Professional Documents
Culture Documents
By 15432
What is RGH3?:
RGH 3 is a new method to glitch your XBOX 360 console. This method only requires 2
wires and some resistors. No glitch chip required.
Phat motherboards
Jasper (16mb/256mb/512mb)
Falcon
NOTE: RGH3 is very hit or miss on some phat consoles. If you have
issues, or strange booting behaviour, your console might not be playing
nice with RGH3 and I would strongly advise using RGH1.2.
Slim motherboards
Trinity
Corona (v1 – v6)
Need help understanding what console you have? Use Octal’s Xbox 360 Identification
Wizard!
Tools:
https://xbox360hub.com/guides/rgh-3-guide/ 1/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
A soldering iron and some soldering experience as you’ll be working with tiny
points.
NOTE: Corona V3/V4/V5/V6 motherboards will need a Post Fix
Adapter, if you are unsure please follow this diagram:
Raspberry Pi Pico:
If you want to use the Raspberry Pi Pico – make sure you are using the latest version of
Octal450’s J-Runner with Extras or Balika011’s J-Runner Pro.
You will also need to flash your Raspberry Pi Pico with the latest version of PicoFlasher
which can be found here: https://github.com/X360Tools/PicoFlasher/releases/
1. Simply hold the BOOTSEL button down on your Pico and plug into your computer,
it should show up as removable storage.
2. Click and drag the UF2 file to the Pico in your file explorer. The device should
automatically unmount on completion.
3. Now, load up J-Runner and you should see PicoFlasher come up as connected
device. Once you see this, follow through with steps below!
Steps:
https://xbox360hub.com/guides/rgh-3-guide/ 2/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
Step 1: Tear down your console to the motherboard, follow guides on YouTube if you get
stuck!
Step 2: Once torn down, solder your NAND headers to your console. Here are some
diagrams for each console variation
Phat motherboards
Trinity motherboards
Corona motherboards
JR-P / NAND-X / xFlasher 360
PicoFlasher
https://xbox360hub.com/guides/rgh-3-guide/ 3/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
Step 3: Once you connect your NAND reader cables, wire up your RGH3 cables. See below
for install points.
Phat motherboards
Trinity motherboards
Corona motherboards
Place a 22k resistor on the PLL point and solder your wire to the other side of the resistor.
Place a 1n4148 diode with the cathode end (black banded end) on POST and solder your
wire to the other side of the Diode.
Bottomside Points
https://xbox360hub.com/guides/rgh-3-guide/ 4/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
https://xbox360hub.com/guides/rgh-3-guide/ 5/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
Step 4: Once you are happy with the points, they are connected properly, and your NAND
cables are installed, it’s time to glitch the console!
Give your console standby power and and connect
your programmer. Follow the steps
below.
J-Runner instructions:
https://xbox360hub.com/guides/rgh-3-guide/ 6/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
To begin – press the ‘?’ button in J-Runner to make sure your programmer can see your
console properly.
If you get an error
– check your programmer wires before continuing!
Video showcase
https://xbox360hub.com/guides/rgh-3-guide/ 7/8
30/07/22, 12:32 RGH 3 Guide – XBOX 360 HUB
https://xbox360hub.com/guides/rgh-3-guide/ 8/8