Professional Documents
Culture Documents
Dashboard
Courses
Engineering
MEM30319 - Certificate III in Engineering - Fabrication Trade
MEM24001B-C3
ASSESSMENT TASK 1
Multiple Choice Test Task 1
Question 1
Correct
Which welding faults are detected by the Dye Penetrant Test (DPT)?
Select all that apply
Surface cracks
Porosity
Laminations
Question 2
Correct
Application of Penetrant
Application of Developer
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 1/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 3
Correct
It may cause to maximize the mistakes that are found by the inspector
Question 4
Correct
What Personal Protective Equipment (PPE) is worn when performing the Dye Penetrant Test (DPT)?
Select all that apply
Coveralls
Gloves
Question 5
Correct
What Personal Protective Equipment (PPE) is worn when performing the DPT in the workplace that
ventilation is restricted?
Select all that apply
A mask
Smoke hood
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 2/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 6
Correct
Question 7
Correct
What factors influence the selection of a sensitivity level on for the Dye Penetrant Test (DPT)?
Select all that apply
Question 8
Correct
Which is the correct statement about the liquid penetrant inspection procedure?
Select all that apply
Liquid penetrant inspection is one of the oldest, simplest, least expensive and most reliable non destructive
examination methods
Liquid penetrant inspection is one of the newest, simplest, least expensive and most reliable non destructive
examination methods
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 3/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 9
Correct
Why does the test surface need to often clean post and after the inspection?
Select all that apply
Because the residue may after the material in a negative way and cause to the unexpected harm to the
material and weld
Because the residue material and weld may be turned into black color
Question 10
Correct
Which is the correct process when using non-aqueous developer (NAD) or dry power to the
sample?
Select all that apply
The sample must be cleaned of the residue penetrant and wetted prior to application
The sample must not be cleaned of the residue penetrant until the final product is finished
Question 11
Correct
Which developer types are available after the excess penetrant has been removed?
Select all that apply
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 4/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 12
Correct
Select one:
It is generally 5 to 30 minutes for the penetrant is allowed time to soak into any flaws
It is generally 1 hour for the penetrant is allowed time to soak into any flaws
It takes only 5 minutes for the penetrant is allowed time to soak into any flaws
It is generally 2 hours for the penetrant is allowed time to soak into any flaws
Question 13
Correct
What is the potential defect if the excess penetrant is not properly removed once the developer is
applied?
Select all that apply
It may leave a background in the developed area that can mask indications or defects
Question 14
Correct
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 5/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 15
Correct
"Lipophilic emulsifiers were introduced in the 1950s and work with both a chemical and
mechanical action".
Question 16
Correct
To reflect and refract the incident ultraviolet light, allowing more of it to interact with the penetrant,
causing more efficient fluorescence
To create a white background so there is a greater degree of contrast between the indication and the
surrounding background
Question 17
Correct
"To meet statutory requirements, the penetrant spray cans should be stored in well-ventilated areas ".
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 6/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 18
Correct
Question 19
Correct
Question 20
Correct
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 7/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Question 21
Correct
Vapour degreasing
Media blasting
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 8/9
3/21/22, 2:33 AM Multiple Choice Test Task 1: Attempt review
Stay in touch
Baxter Institute
http://www.baxter.vic.edu.au
03 9650 0367
mail@baxter.vic.edu.au
Data retention summary
Get the mobile app
https://baxter.edfibre.com/gradejet/mod/quiz/review.php?attempt=107579&cmid=8317 9/9