Professional Documents
Culture Documents
07
Replaces: 22048
/14
Type .-.SE
Size 6
Component series 7X
Maximum operating pressue 630 bar
Maximum flow 25 l/min
H7453
Ordering code
SE 6 7X K4 *
Oil-in-water Further
emulsion, details in clear text
water glycol, No code = Without
mineral oil = E locating bore
Water =W /62 = With locating bore
3 main ports =3 and locating pin
4 main ports =4 ISO 8752-3x8-St
Poppet valve, electrically operated Seal material
No code = NBR seals
Size 6 =6
V = FKM seals
Main ports 3 4 (other seals on request)
A Important!
a b Observe compatibility of seals
– =U with hydraulic fluid used!
a b
P T
No code = Without check
A valve insert,
a b without throttle insert
– =C
a b P = With check valve insert
Symbols
1) Mating
connectors must be ordered separately (see
AC mains (permissible Nominal voltage of the
Order-
code
page 14).
ing
7 3 8 1
Type .-3SE 6 U …
2 5 6
4 T P
A
/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
7 3 8 1
2 16 5 6
4 T A P
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG /14
Symbol
– Starting position:
"D"
The main valve is not operated. Spring (8) holds ball (4.2) a b a b
a b a b
on seat (11). Port P is blocked, and A is connected to T. In
P T P T
addition, a pilot line is connected from A to the large area of
pilot piston (12), which is hence unloaded to the tank. The A B A B
Symbol
pressure applied via P now pushes ball (13) onto seat (14). P
"Y"
is now connected to B, and A to T. a b a b
a b a b
– Transitional position: P T P T
When the main valve is operated, ball (4.1) is shifted against
spring (8) and pushed onto seat (15). This causes blocking
of port T; P, A, and B are briefly connected.
Schematic drawing: Starting position
– Operated position:
P is connected to A. Because the pump pressure acts via 4.1 15 11 4.2 8
the large area of pilot piston (12), ball (13) is pushed onto
seat (10). Consequently, B is connected to T, and P to A.
Ball (13) in the Plus-1 plate has a "positive overlap".
Important! A
In order to prevent pressure intensification when using
single-rod cylinders, the annulus area of the cylinder must be
connected to A.
T P
4/2 directional seat valves with detent analogously to 3/2 di-
rectional poppet valve (see page 4).
A T B P
12 14 13 10
3 8 1
4.2
4.1 11
13
15
12 10
T P
Type .-4SE 6 Y … B A
/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
Standard types
Technical data (for applications outside these parameters, please consult us!)
General
Weight – 3/2 directional • without detent kg 3.8
poppet valve • with detent kg 5.6
– 4/2 directional • without detent kg 4.6
poppet valve • with detent kg 6.4
Installation position Optional
Ambient temperature range °C 5 to 50 (with water, oil-in-water emulsion and water glycol)
°C –15 to +50 (with mineral oil)
Hydraulic
Maximum operating pressure bar see table “Performance limit” on page 9
Maximum flow l/min 25
Hydraulic fluid – Type W-.SE 6 … Water
– Type E-.SE 6 … Oil-in-water emulsion, water glycol, mineral oil (HL, HLP)
to DIN 51524 1); fast bio-degradable hydraulic fluids to
VDMA 24568 (see also RE 90221); HETG (rape seed oil)
1); HEPG (polyglycols) 2); HEES (synthetic esters) 2); other
1) Suitable for NBR and FKM seals 3) The cleanliness classes specified for components must be
2) Suitable only for FKM seals adhered to in hydraulic systems. Effective filtration prevents
malfunction and, at the same time, prolongs the service life
of components.
For the selection of filters, see data sheets RE 50070,
RE 50076, RE 50081, RE 50086, RE 50087 and
RE 50088.
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG /14
Technical data (for applications outside these parameters, please consult us!)
Electrical
Type of voltage DC voltage AC voltage
Available voltages V 12; 24; 42; 48; 96; 110; 205 Only possible via rectifier (see
(further voltages on request) page 14)
Voltage tolerance (nominal voltage) % ±10
Power consumption – Valve solenoid W 35
– Detent solenoid W 30
Duty cycle S1 (continuous operation)
Switching time ON ms 40 to 70 (420 bar); 50 to 80 (630 bar)
to ISO 6403 OFF ms 20 to 30 (420 bar); 15 to 40 (630 bar)
Maximum switching frequency 1/h 3600
Maximum coil temperature 4) °C 150
Type of protection to EN 60529 IP 65 with mating connector mounted and locked
4) Due
to the surface temperatures of solenoid coils, European
standards EN 563 and EN 982 must be observed!
20 20
2
16 16
12 12
8 8
4 4
0 5 10 15 20 25 0 5 10 15 20 25
Flow in l/min → Flow in l/min →
1 A to T 1 A to T 2 B to T
P to A P to A P to B
12 630
600
B08 B10 B12
10
Pressure differential in bar →
500
8 B15
400
6
300
4 B18
200
2 B20
100
0 4 8 12 16 20 24 25 0 4 8 12 16 20 24 25
Flow in l/min → Flow in l/min →
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG /14
P T
Pressure pP ≥ pA ≥ pT
A
a b
C 420/630 420/630 200 25
a b
P T
A
a b
C Pressure pA ≥ pT 420/630 200 25
a b
P T
A B
(flow only possible in the
P T pP > pA ≥ pB > pT
A B
Valve (symbol “C“) in
Y a b conjunction with Plus-1 plate 420/630 420/630 420/630 200 25
a b
P T pP > pA ≥ pB > pT
General notes
– In order to reliably operate and hold the valve in its oper- – When using the Plus-1 plate (4/2 directional function) ob-
ated position, the pressures must be: P ≥ A ≥ T (for design serve the following lower operating values:
reasons). pmin = 8 bar; qV > 3 l/min.
– Ports P, A and T (3/2 directional poppet valve) and P, A, B – The total flow of the valve must not be exceeded.
and T (4/2 directional poppet valve) are clearly assigned
according to their task. They must not be exchanged or
plugged. Flow is only permitted in the direction of the arrow.
10/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
5 1 2 5
15
15
142
135
48,6
8,5
72,9 9 50
64
3 7 8 11
226,2
164,9
20,6 0,01/100
6 Rzmax 4
F1
T F2
9,5
1 Mating connector without circuitry (separate order, see 11 Valve fixing screws
page 14) (included in the scope of supply)
2 Mating connector with circuitry (separate order, – 420 bar variant:
see page 14) 4 hexagon socket head cap screws
ISO 4762 M5 x 50 - 10.9-flZn-240h-L
3 DC solenoid
(Friction coefficient µtotal = 0.09 to 0.14);
4 Nameplate tightening torque MT = 7 Nm ± 10%,
5 Space required to remove mating connector
6 – 630 bar variant (not to ISO 4401):
Attention!
4 hexagon socket head cap screws
Port B is provided as blind countersunk hole on 3/2 direc-
ISO 4762 M6 x 50 - 10.9-flZn-240h-L
tional poppet valves in the 420 bar variant, and not provided
(Friction coefficient µtotal = 0.09 to 0.14);
for the 630 bar variant.
tightening torque MT = 12.5 Nm ± 10%
7 Identical seal rings for ports A, B, P and T
8 Porting pattern to ISO 4401-03-02-0-05
(with locating bore and locating pin ISO 8752-3x8-St);
deviating from standard: Variant “630“
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG 11/14
Unit dimensions: 3/2 directional poppet valve – with detent (nominal dimensions in mm)
5 2 5 1 57 15 5
15
15
1
175,4
4
142
135
48,6
8,5
72,9 9 50
64
3 9 7 8 11
273,6
212,3
78,35
20,6
6
F1
T F2
9,5
A B
0,01/100
F4 P G F3
Rzmax 4
1 Mating connector without circuitry (separate order, see 9 Detent with DC solenoid
page 14) 11 Valve fixing screws
2 Mating connector with circuitry (separate order, (included in the scope of supply)
see page 14) – 420 bar variant:
3 DC solenoid 4 hexagon socket head cap screws
ISO 4762 M5 x 50 - 10.9-flZn-240h-L
4 Nameplate
(Friction coefficient µtotal = 0.09 to 0.14);
5 Space required to remove mating connector tightening torque MA = 7 Nm ± 10%,
6 Attention!
Port B is provided as blind countersunk hole on 3/2 direc- – 630 bar variant (not to ISO 4401):
tional poppet valves in the 420 bar variant, and not provided 4 hexagon socket head cap screws
for the 630 bar variant. ISO 4762 M6 x 50 - 10.9-flZn-240h-L
(Friction coefficient µtotal = 0.09 to 0.14);
7 Identical seal rings for ports A, B, P and T
tightening torque MT = 12.5 Nm ± 10%
8 Porting pattern to ISO 4401-03-02-0-05
(with locating bore and locating pin ISO 8752-3x8-St);
deviating from standard: Variant “630“
12/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
5 1 2 5
15
15
142
135
48,6
44,4
3 10
9
62,7 45
7 72,9 9 50
64
8 11
226,2
164,9
20,6
F1
T F2
9,5
A B 0,01/100
F4 P G F3 Rzmax 4
1 Mating connector without circuitry (separate order, see 11 Valve fixing screws
page 14) (included in the scope of supply)
2 Mating connector with circuitry (separate order, – 420 bar variant:
see page 14) 4 hexagon socket head cap screws
ISO 4762 M5 x 95 - 10.9-flZn-240h-L
3 DC solenoid
(Friction coefficient µtotal = 0.09 to 0.14);
4 Nameplate tightening torque MT = 7 Nm ± 10%,
5 Space required to remove mating connector
7 Identical seal rings for ports A, B, P and T – 630 bar variant (not to ISO 4401):
4 hexagon socket head cap screws
8 Porting pattern to ISO 4401-03-02-0-05 ISO 4762 M6 x 95 - 10.9-flZn-240h-L
(with locating bore and locating pin ISO 8752-3x8-St); (Friction coefficient µtotal = 0.09 to 0.14);
deviating from standard: Variant “630“ tightening torque MT = 12.5 Nm ± 10%
10 Plus-1 plate
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG 13/14
Unit dimensions: 4/2 directional poppet valve – with detent (nominal dimensions in mm)
5 2 5 1 57 15 5
15
15
1
175,4
4
186,4
179,4
48,6
3 9
44,4
10
9
62,7 45
72,9 9 50
64
7 8 11
273,6
212,3
78,55
20,6
F1
T F2
0,01/100
9,5
A B Rzmax 4
F4 P G F3
1 Mating connector without circuitry (separate order, see 11 Valve fixing screws
page 14) (included in the scope of supply)
2 Mating connector with circuitry (separate order, – 420 bar variant:
see page 14) 4 hexagon socket head cap screws
ISO 4762 M5 x 95 - 10.9-flZn-240h-L
3 DC solenoid
(Friction coefficient µtotal = 0.09 to 0.14);
4 Nameplate tightening torque MT = 7 Nm ± 10%,
5 Space required to remove mating connector
7 Identical seal rings for ports A, B, P and T – 630 bar variant (not to ISO 4401):
4 hexagon socket head cap screws
8 Porting pattern to ISO 4401-03-02-0-05 ISO 4762 M6 x 95 - 10.9-flZn-240h-L
(with locating bore and locating pin ISO 8752-3x8-St); (Friction coefficient µtotal = 0.09 to 0.14);
deviating from standard: Variant “630“ tightening torque MT = 12.5 Nm ± 10%
9 Detent with DC solenoid
10 Plus-1 plate
14/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
For details
and further mat-
ing connectors,
see RE 08006
Material no.
With indicator lamp and
Valve With indicator lamp With rectifier Zener diode suppressor cir-
side Colour Without circuitry 12 … 240 V 12 … 240 V cuit 24 V
a Grey R901017010 – – –
a Black – R901017022 R901017025 R901017026
Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
documentation@boschrexroth.de release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.
RE 22042/03.07 .-.SE Hydraulics Bosch Rexroth AG 15/14
Notes
Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
documentation@boschrexroth.de release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.
16/14 Bosch Rexroth AG Hydraulics .-.SE RE 22042/03.07
Notes
Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
documentation@boschrexroth.de release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.