Professional Documents
Culture Documents
CATIA 06 Crtezi
CATIA 06 Crtezi
• Standard
• Format
• Orientation
• Iz linijskog menija bira se: Start > Mechanical Design > Drafting,
po čemu se otvara prozor za dijalog New Drawing Creation.
Vrste pogleda
CATIA obezbeđuje sledeće vrste pogleda:
GENERISANJE POGLEDA
• Postoje dve metode za generisanje pogleda na crtežu po startovanju
praznog fajla u radnom okruženju Drafting. Prvi je automatsko generisanje
korišćenjem vizarda, a drugi, pojedničano generisanje pogleda.
Izabrani parametri za
generisanje pomoćnog pogleda
Zaokrenuti presek
Detalj
Detalj sa profilom
Odsečak sa profilom
• Generisanje skraćenog pogleda (Broken View)
• Definišu se tačke koje pokazuju prvu i drugu liniju skraćenja. Može se
primeniti na projekcije, ali i na izometrijske poglede.
Prozor za dijalog
Enhaced Scene Crtež rastavljenog sklopa
Interaktivno crtanje
• U radnom okruženju crteža moguće je skicirati ravanske crteže, što se
naziva interaktivnim crtanjem.
• Crtanje se vrši poznatim alatima iz palete Geometry Creation, a
podešavanje karakteristika nacrtanih elemanata alatima iz palete
Graphics Properties. .
Moguće je vršiti:
• Promenu razmere,
• Brisanje pogleda,
• Zaokretanje pogleda i
• Skrivanje pogleda.
Tutorial 1
In this tutorial, you will generate the drawing views of the model of Motor
Cover created in Tutorial 2 of Chapter 7. You will generate the front view,
top view, aligned section views from the top view, detail view, and the
isometric view. You will use the A4 standard sheet size and the third
angle projection. The drawing sheet after generating all the views is
shown in Figure A. (Expected time: 30 min)
1. Copy the part document of Tutorial 2 from Chapter 7 to the folder of the current c
2. Start a new file in the Drafting workbench with the standard A4 sheet size.
4. Generate the front view, which will be used as the main view, as shown in Figure
5. Generate the top view using the Projection View tool, as shown in Figure C.
6. Generate the aligned section view from the top view after activating it,
as shown in Figure D and Figure E.
Figure D Sketch for the section view Figure E Drawing sheet after
generating the aligned section
view
9. Save the file in \My Documents\CATIA\c12 folder and then close it.
Tutorial 2
In this tutorial, you will create the Bench Vice assembly and then
generate the front, top, right, and isometric views of the same, as shown
in Figure A. Figure B, Figure C, Figure D, and Figure E shows the
views and dimensions of the components of the Bench Vice assembly.
(Expected time: 2 hrs)
1. Create all components of the Bench Vice assembly and assemble them.
2. Start a new file in the Drafting workbench using the A2 size sheet.
Exercise 1
Create the components of the V-Block and generate the front, top, right,
detail, and isometric views, as shown in Figure A. The views and
dimensions of the components of the V-Block are shown in Figure B and
Figure C.
• Akcija (Action)
• Kreiranje (Creation)
• Brisanje (Deletion)
• Podešavanje veličine
(Resizing)
• Aţuriranje (Update)
DORADA CRTEŽA
• Po generisanju pogleda na crtežu potrebno je generisati kote na pojedinim
pogledima i dodati ostale sadržaje kao što su: napomene, simboli za
kvalitete obrađenih površina, tolerancije, ... Postoje dve vrste podataka koji
mogu dodati crtežu: prvo su generativni podaci kao što su: dimenzije
definisane pri kreiranju delova, a drugo su ručno dadati podaci kao što su:
referentne dimenzije, napomene, ... .
• Generisanje kota
• Generisanje svih kota (all Dimensions
Together)
• Koristi se da se generišu sve dimenzije jednim
klikom. Prvo se pozove prozor za dijalog Options i
izabere Drafting iz Mechanical Design opcija. Po
tome se aktivira tabulator Generation i izabere se
Filter before generation prozor za dijalog. Zatim se
izlazi iz prozora za dijalog Options i bira se komanda
Generate Dimensions iz palete Dimension
Generation koja se otvara po pozivanju Generation
palete alata. Po tome se otavra prozor za dijalog
Dimension Generation Filters. Prozor za dijalog Dimension
Generation Filter
Paleta Dimensions
Prozor za dijalog
Generate Numbering
Crtež po generisanju BOM-a
Postavljanje pozicija(Balloons)
• Koristi se za postavljanje pozicija na crtežima. Aktivira se kroz Generation
> Dimension Generation > Generate Balloons
Tutorial 1
In this tutorial, you will create the model shown in Figure A. After
creating it you need to generate the front, top, and the isometric views in
the Drafting workbench. You also need to generate the dimensions in
the drawing views. The views and dimensions are shown in Figure B.
(Expected time: 45 min)
1. Create the model in the Part workbench and save the file in the c13 folder.
2. Start a new file in the Drafting workbench with the standard sheet of A2 size.
4. Create a standard title block and frame in the background editing mode,
as shown in Figure C.
9. Save the file in \My Documents\CATIA\c13 folder and then close it.
Tutorial 2
In this tutorial, you will generate the front, top, right, and isometric views
of the V-Block assembly created in the Exercise 1 of Chapter 12. You also
need to generate the BOM and balloons.
(Expected time: 30 min)
8. The drawing sheet after generating all the drawing views is shown in Figure A.
11. The final drawing sheet after generating the BOM and balloons is shown in Figur
12. Save the file in \My Documents\CATIA\c13 folder and then close it.
Exercise 1
Generate the front, top, right, and isometric views of the Blower assembly
created in Tutorial 1 of Chapter 11. The drawing view will be generated with
the scale factor of 1:5. After generating the drawing views, you need to
generate the BOM and balloons, as shown in Figure A.
(Expected time: 30 min)