Professional Documents
Culture Documents
1 UPDATES
2
CHAPTER 1
General
Requirements
3
SUMMARY OF REVISIONS
4
Section 103:
OCCUPANCY CATEGORY
OCCUPANCY REVISED
CATEGORY Iw I TO
7
Chapter 2:
MINIMUM DESIGN LOADS
Dead Loads
Live Loads (Floor Live Loads)
Roof Live Load
Wind Load
Earthquake Loads
Soil lateral loads
Rain Loads
Flood Loads
Other Minimum Loads
(Impact Loads, Elevators, Machinery, Water
Accumulation, Hydrostatic Uplift, Crane
Loads, Heliport & Helistop Landing Areas) 8
Section 203 : Load Combinations
Symbols and Notations
D = Dead Load
W = Wind Load
E = Earthquake Load
P = ponding load
12
Load Combinations, Strength Design
D + (W or E/1.4) D + H + F + (W or
E/1.4)
0.9D+ (E/1.4)
0.9D - (E/1.4)
D + 0.75 [L + Lr D + H + F + 0.75 [ L + T
+(W or E/1.4)] + (Lr or R)]
ASD Alternate Basic
Load Combinations
NSCP 2001 NSCP 2010
Sec. 203.4.2 Sec. 203.4.2
D + H + F + 0.75 [L + Lr + (W or
D + L +Lr
E/1.4)]
D+L+W 0.6D + W + H
D + L + (Lr or R)
D + L + E/1.4 0.6D + (E/1.4) + H
D+L+W
D + L + (E/1.4)
0.9D + 1.0 Em
0.9D - 1.0 Em
where:
f1 = 1.0 for floors in places of public
assembly, for live loads in excess of
4.8kPa, and for garage live load
= 0.5 for other live loads
Em = the estimated maximum earthquake
force that can be developed in the
structure.
Sec. 104.5 DESIGN REVIEW
(Peer Review)
18
Sec. 104.5 DESIGN REVIEW
(Peer Review)
20
21
PART 1
SEISMIC LOAD
CALCULATION
Design Base Shear
V= Cv I W (Eq. 208-4)
RT
Where:
V = is the total design seismic force
Cv = Seismic coefficient in Table 208-8
I = Importance factor in Table 208-1
W = Total dead load per Sect.
208.5.1.1
R = Numerical coefficient in Table
208-11
Design Base Shear (Cont’n.)
Base Shear need not exceed the ff:
Where:
Ca = Seismic Coefficient in
Table 208-7
I, W, & R = as previously defined
Design Base Shear ( Cont’n.)
Base Shear shall not be < the ff:
V= 0.11 Ca I W Eq.
208-6
In Zone 4, Base Shear shall not be <
the ff:
V= 0.8 Z Nv I W Eq. 208-7
R
Where:
Z = Seismic Zone Factor in Table 208-3
Seismic Parameters
Table 208-1 - Seismic Importance Factors
Seismic Seismic
Occupancy
1 Importance Importance 2
Category
Factor, I Factor, Ip
I. Essential
Facilities 3 1.5 1.25 1.50
II. Hazardous
Facilities 1.5 1.25 1.50
III. Special
Occupancy 1.00 1.00
Structures4
IV. Standard
Occupancy 1.00 1.00
Structures4
V.Miscellaneous
1.00 1.00
structures
Table 208-2 - Soil Profile Types
Average Soil Properties For Top 30 m Of
Soil Profile
Soil Profile Shear
Soil Profile
Name/ Generic Wave SPT, N
Type Undrained Shear
Description Velocity, (blows /
Strength, (kPa)
Vs 300 mm)
(m/s)
SA Hard Rock > 1,500
760 to
SB Rock
1,500
Very Dense
360 to
SC Soil ad Soft > 50 > 100
760
Rock
Stiff Soil 180 to 15 to
SD 50 to 100
Profile 360 50
Soft Soil
S E1 < 180 < 15 < 50
Profile
Soil Requiring Site-specific Evaluation.
SF
See Section 208.4.3.1
1
Soil Profile Type SE also includes any soil profile with more than 3.0 meters of
soft clay defined as a soil with plasticity index, Pl>20, wmc ≥ 40 percent and su <
24 kPa. The Plasticity Index, PI, and the moisture content, wmc, shall be
determined in accordance with approved national standards.
Seismic Parameters
T= Ct (hn)3/4