Professional Documents
Culture Documents
CS/CJ Series
HOST Link Driver
1 System Configuration....................................................................................................... 3
2 Selection of External Device .......................................................................................... 13
3 Example of Communication Setting ............................................................................... 14
4 Setup Items .................................................................................................................... 58
5 Cable Diagram ............................................................................................................... 63
6 Supported Device......................................................................................................... 139
7 Device Code and Address Code.................................................................................. 145
8 Error Messages............................................................................................................ 147
1
CS/CJ Series HOST Link Driver
Introduction
This manual describes how to connect the Display and the External Device (target PLC).
In this manual, the connection procedure will be described by following the below sections:
1 System Configuration
)"1 System Configuration" (page 3)
This section shows the types of External
Devices which can be connected and SIO
type.
4 Communication Settings
)"4 Setup Items" (page 58)
This section describes communication
setup items on the Display.
Set communication settings of the Display
with GP-Pro EX or in offline mode.
5 Cable Diagram
)"5 Cable Diagram" (page 63)
This section shows cables and adapters
for connecting the Display and the
External Device.
Operation
1 System Configuration
The system configuration in the case when the External Device and the Display are connected is shown.
Communication
Series CPU*1 Connection Port SIO Type Cable Diagram
Settings
Communication
Series CPU*1 Connection Port SIO Type Cable Diagram
Settings
CJ1W-SCU31-V1 RS422/485
CJ2H-CPU68-EIP Setting Example 6 Cable Diagram 4
(4wire)
CJ2H-CPU67-EIP (page 30) (page 78)
Multilink
CJ2H-CPU66-EIP
CJ2H-CPU65-EIP
CJ2H-CPU64-EIP Setting Example 5 Cable Diagram 1
RS-232C
(page 26) (page 63)
CJ2
RS232C serial port Setting Example 11 Cable Diagram 1
RS-232C
on the CPU unit (page 46) (page 63)
Communication
Series CPU*1 Connection Port SIO Type Cable Diagram
Settings
CJ1W-SCU31-V1 RS422/485
Setting Example 6 Cable Diagram 4
(4wire)
CJ2M-CPU35 (page 30) (page 78)
Multilink
CJ2M-CPU34
CJ2 CJ2M-CPU33
CJ2M-CPU32 Setting Example 5 Cable Diagram 1
RS-232C
CJ2M-CPU31 (page 26) (page 63)
Communication
Series CPU*1 Connection Port SIO Type Cable Diagram
Settings
CJ1W-SCU31-V1 RS422/485
Setting Example 6 Cable Diagram 4
(4wire)
(page 30) (page 78)
Multilink
CP1E-NDR-A
CP1E-NDT-A
Internal RS-232C
CP1E-NDT1-A Setting Example 12 Cable Diagram 1
CP1E port on the CPU RS232C
CP1E-NDR-D (page 49) (page 63)
unit
CP1E-NDT-D
CP1E-NDT1-D
Communication
Series CPU*1 Connection Port SIO Type Cable Diagram
Settings
Internal RS-232C
Setting Example 11 Cable Diagram 9
port on the CPU RS232C
(page 46) (page 135)
CP2E-ED- unit
CP2E-SD- Internal RS-485
RS422/485 Setting Example 13 Cable Diagram 7
port on the CPU
(2wire) (page 52) (page 111)
unit
RS422/485
CP1W-CIF11 Setting Example 10 Cable Diagram 6
(4wire)
CP2E CP1W-CIF12-V1 (page 43) (page 99)
*4 Multilink
• When the time of GP4000 series is automatically updated in [Clock Update Settings] of GP-Pro
EX, there are some restrictions as shown below.
For details on [Clock Update Settings], refer to GP-Pro EX Reference Manual.
•CP1L, CP1E and CJ2H does not support automatic update of the time. Specify [Customize] in
[Clock Update Settings].
Connection Configuration
• 1:1 Connection
• 1:n Connection
Usable port
Usable Port
Series
RS-232C RS-422/485(4 wire) RS-422/485(2 wire)
COM1*1 , COM2,
PS-2000B - -
COM3*1, COM4
PS-3450A, PS-3451A,
COM1, COM2*1*2 COM2*1*2 COM2*1*2
PS3000-BA, PS3001-BD
PS-3650A (T41 model),
COM1*1 - -
PS-3651A (T41 model)
PS-3650A (T42 model),
COM1*1*2, COM2 COM1*1*2 COM1*1*2
PS-3651A (T42 model)
PS-3700A (Pentium®4-M) COM1*1, COM2*1,
COM3*2 COM3*2
PS-3710A COM3*2 , COM4
PS-3711A COM1*1, COM2*2 COM2*2 COM2*2
PS4000*3 COM1, COM2 - -
COM1*1*2, COM2*1,
PL3000 COM1*1*2 COM1*1*2
COM3, COM4
PE-4000B Atom N270 COM1, COM2 - -
*4 COM4*4, COM3*4, COM4*4,
COM3 ,
PE-4000B Atom N2600 COM1, COM2
COM5*4, COM6*4 COM5*4, COM6*4
PS5000 (Slim Panel Type
COM1, COM2*4 COM2*4 COM2*4
Core i3 Model) *5 *6
PS5000 (Slim Panel Type
Atom Model) COM1, COM2*7 COM2*7 COM2*7
*5 *6
*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.
*2 Set up the SIO type with the DIP Switch. Please set up as follows according to SIO type to be used.
*3 When making communication between an External Device and COM port on the Expansion slot,
only RS-232C is supported. However, ER (DTR/CTS) control cannot be executed because of the
specification of COM port.
For connection with External Device, use user-created cables and disable Pin Nos. 1, 4, 6 and 9.
Please refer to the IPC manual for details of pin layout.
*4 Set up the SIO type with the BIOS. Please refer to the IPC manual for details of BIOS.
*5 When setting up communication between an External Device and the RS-232C/422/485 interface
module, use the IPC (RS-232C) or PS5000 (RS-422/485) cable diagrams. However, when using
PFXZPBMPR42P2 in a RS-422/485 (4-wire) configuration with no flow control, connect 7.RTS+
and 8.CTS+, and connect 6.RTS- and 9.CTS-.
When using RS-422/485 communication with External Devices, you may need to reduce the
transmission speed and increase the TX Wait time.
*6 To use RS-422/485 communication on the RS-232C/422/485 interface module, the DIP Switch
setting is required. Please refer to "Knowledge Base" (FAQs) on the support site. (http://www.pro-
face.com/trans/en/manual/1001.html)
Settings FAQ ID
PFXZPBMPR42P2, RS422/485 change method FA263858
PFXZPBMPR42P2 termination resistor setting FA263974
PFXZPBMPR44P2, RS422/485 change method FA264087
PFXZPBMPR44P2 termination resistor setting FA264088
*7 Set up the SIO type with the DIP Switch. Please refer to the IPC manual for details of DIP Switch.
The BOX Atom has not a switch to set the RS-232C, RS-422/485 mode. Use the BIOS for the
setting.
*8 For the connection with the External Device, on the user-created cable read as if the connector on
the Display-side is a M12 A-coding 8 pin socket. The pin assignment is the same as described in
the cable diagram. For the M12 A-coding connector, use PFXZPSCNM122.
*9 In addition to COM1, you can also use the RS-232C COM port on the optional interface.
*10 Install the optional interface in the expansion slot.
RS-422/485 (4 wire)
RS-422/485 (2 wire)
Examples of communication settings of the Display and the External Device, recommended by Pro-face, are
shown.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
• Do not set the duplicate node address in the same network address group.
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Set the unit No. you set in the External Device for "Unit No.".
• If you do not access beyond network, set "0" for "Network" and "Node" settings.
Notes
• Do not set the duplicate node address in the same network address group.
4 Setup Items
Set communication settings of the Display with GP-Pro EX or in offline mode of the Display.
The setting of each parameter must be identical to that of External Device.
)"3 Example of Communication Setting" (page 14)
4.1 Setup Items in GP-Pro EX
Communication Settings
To display the setup screen, from the [Project] menu, point to [System Settings] and select [Device/PLC].
Device Setting
To display the [Individual Device Settings] dialog box, from [Device-Specific Settings] in the [Device/PLC]
window, select the external device and click [Settings] .
To connect multiple External Devices, from [Device-Specific Settings] in the [Device/PLC] window, click [Add
Device] to add another External Device.
• Refer to the Maintenance/Troubleshooting Guide for information on how to enter offline mode or
about the operation.
• The number of the setup items to be displayed for 1 page in the offline mode depends on the
Display in use. Please refer to the Reference manual for details.
Communication Settings
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings] in offline mode. Touch the
External Device you want to set from the displayed list.
To make the communication settings correctly, confirm the serial interface specifications of
SIO Type
Display unit for [SIO Type].
We cannot guarantee the operation if a communication type that the serial interface does not
support is specified.
For details concerning the serial interface specifications, refer to the manual for Display unit.
Speed Select speed between the External Device and the Display.
Data Length Select data length.
Parity Select how to check parity.
Stop Bit Select stop bit length.
Flow Control Select the communication control method to prevent overflow of transmission and reception data.
Use an integer from 1 to 127 to enter the time (s) for which the Display waits for the response from
Timeout
the External Device.
Device Setting
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device
you want to set from the displayed list, and touch [Device].
Option
To display the setting screen, touch [Device/PLC Settings] from [Peripheral Settings]. Touch the External Device
you want to set from the displayed list, and touch [Option].
• GP-4100 series, GP-4*01TM, GP-Rear Module, LT-4*01TM and LT-Rear Module do not
have the [Option] setting in the offline mode.
5 Cable Diagram
The following cable diagrams may be different from cable diagrams recommended by External Device
Manufacturer.
Please be assured there is no operational problem in applying the cable diagram shown in this manual.
• The FG pin of the External Device body must be grounded according to your country’s applicable standard.
Refer to your External Device manual for details.
• SG and FG are connected inside the Display. When connecting the External Device to SG, design your system
to avoid short-circuit loops.
• Connect an isolation unit if the communication is not stable due to noise or other factors.
Display
Cable Notes
(Connection Port)
GP3000 (COM1) Omron PLC SYSMAC Link Cable (5m) by Pro-face
GP4000*1 (COM1) CA3-CBLSYS-01
SP5000*2 (COM1/2) 1A or
SP-5B00 (COM1) XW2Z-200S-V (2m) or
ST3000 (COM1) XW2Z-500S-V (5m) by OMRON Corporation The cable length must be
ST6000 (COM1) 15m or less.
STM6000 (COM1)
LT3000 (COM1) 1B User-created cable
IPC*3
PC/AT
GP-4105 (COM1)
GP-4115T (COM1) The cable length must be
1C User-created cable
GP-4115T3 (COM1) 15m or less.
LT-4*01TM (COM1)
RJ45 RS-232C Cable (5m) by Pro-face
LT-Rear Module The cable length must be
1D PFXZLMCBRJR21
(COM1) 5m or less.
1A)
CA3-CBLSYS-01
or
XW2Z-200S-V
External
Display or
Device
XW2Z-500S-V
1B)
Display side External Device side
D-sub 9 pin (socket) Shield D-sub 9 pin (plug)
Signal Signal
Pin name Pin name
Display 3 SD(TXD) 2 SD(TXD)
2 RD(RXD) 3 RD(RXD)
7 RS(RTS) 4 RS(RTS)
8 CS(CTS) 5 CS(CTS)
5 SG 9 SG
1 FG
1C)
Display side External Device side
Terminal block Shield D-sub 9 pin (plug)
Signal Signal
name Pin name
Display SD(TXD) 2 SD(TXD)
RD(RXD) 3 RD(RXD)
RS(RTS) 4 RS(RTS)
CS(CTS) 5 CS(CTS)
SG 9 SG
1 FG
1D)
External Device side
D-sub 9 pin (plug)
Signal
Pin name
Display
RXD 2 SD(TXD)
TXD
3 RD(RXD)
4 RS(RTS)
PFXZLMCBRJR21
5 CS(CTS)
GND
9 SG
1 FG
Display
Cable Notes
(Connection Port)
User-created cable
+
2C
GP-4105 (COM1) CS1W-CN225 (2m) or CS1W-CN625 (6m)
GP-4115T (COM1) by OMRON Corporation The cable length must be
GP-4115T3 (COM1) User-created cable 15m or less.
+
2D
CS1W-CN226 (2m) or CS1W-CN626 (6m)
by OMRON Corporation
2A)
D-sub 25 pin (socket)
Display side for Peripheral Port
D-sub 9 pin (socket) Connection Cable
Signal Signal
Pin name Pin name
2 RD(RXD) 3 RD(RXD)
7 RS(RTS) 4 RS(RTS)
CS1W-CN225
8 CS(CTS) 5 CS(CTS) or
5 SG 7 SG CS1W-CN625
1 FG
User-created cable
2B)
D-sub 9 pin (plug)
Display side
for Peripheral Port
D-sub 9 pin (socket) Connection Cable
Signal Signal
Pin name Pin name
5 SG 5 SG
User-created cable
2C)
D-sub 25 pin (socket)
Display side for Peripheral Port
Terminal block Connection Cable
Signal Signal
name Pin name
RD(RXD) 3 RD(RXD)
RS(RTS) 4 RS(RTS)
CS1W-CN225
CS(CTS) 5 CS(CTS) or
SG 7 SG CS1W-CN625
1 FG
User-created cable
2D)
D-sub 9 pin (plug)
Display side
for Peripheral Port
Terminal block
Connection Cable
Signal Signal
name Pin name
SG 5 SG
User-created cable
2E)
D-sub 25 pin (socket)
for Peripheral Port
Connection Cable
Signal
Pin name
Display
RXD 2 SD(TXD)
TXD
3 RD(RXD)
4 RS(RTS)
PFXZLMCBRJR21
CS1W-CN225
5 CS(CTS)
or
GND
7 SG CS1W-CN625
1 FG
2F)
D-sub 9 pin (plug)
for Peripheral Port
Connection Cable
Signal
Pin name
Display
RXD 2 RD(RXD)
TXD
3 SD(TXD)
7 RS(RTS) CS1W-CN226
PFXZLMCBRJR21 or
8 CS(CTS) CS1W-CN626
GND
5 SG
Display
Cable Notes
(Connection Port)
3B User-created cable
*8 When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block
Conversion Adapter, refer to Cable Diagram 3A.
*9 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
IPC COM Port (page 10)
3A)
• 1:1 connection
Terminal External Device side
block Shield D-sub 9 pin (plug)
Termination Signal Signal
resistance Pin name
name
220Ω 1/4W
RDA 2 SDB
Display RDB 1 SDA
CA3-ADPCOM-01
SDA 8 RDB
SDB 6 RDA
CA3-ADPTRM-01 TERMRX Shell FG
SG
FG
User-created cable
• 1:n connection
Terminal External Device side External Device side
block Shield D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
Termination Signal Signal
Signal Pin Pin
resistance name name name
220Ω 1/4W RDA SDB 2 SDB
2
Display RDB 1 SDA 1 SDA
CA3-ADPCOM-01
SDA 8 RDB 8 RDB
SDB 6 RDA 6 RDA
CA3-ADPTRM-01 TERMRX Shell FG Shell FG
SG
FG
User-created cable
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
3B)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield D-sub 9 pin (plug)
Termination
resistance Signal Signal name
Pin name Pin
220Ω 1/4W
1 RDA 2 SDB
Display 2 RDB 1 SDA
3 SDA 8 RDB
7 SDB 6 RDA
6 CSB Shell FG
9 ERB
8 CSA
4 ERA
• 1:n connection
Display side External Device side
Shield External Device side
Termination D-sub 9 pin (socket) D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
resistance Signal
Pin Signal name Signal name
220Ω 1/4W name Pin Pin
1 RDA 2 SDB 2 SDB
Display 2 RDB 1 SDA 1 SDA
3 SDA 8 RDB 8 RDB
7 SDB 6 RDA 6 RDA
6 CSB Shell FG Shell FG
9 ERB
8 CSA
4 ERA
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
3C)
• 1:1 connection
External Device side
Terminal block Shield D-sub 9 pin (plug)
Termination Signal Signal
Pin
resistance name name
220Ω 1/4W RDA 2 SDB
Display RDB 1 SDA
CA4-ADPONL-01
SDA 8 RDB
SDB 6 RDA
CA3-ADPTRM-01 TERMRX Shell FG
SG
FG
User-created cable
• 1:n connection
External Device side External Device side
Terminal block Shield D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
Termination
resistance Signal Signal Signal
name Pin name Pin name
220Ω 1/4W
RDA 2 SDB 2 SDB
Display RDB 1 SDA 1 SDA
CA4-ADPONL-01
SDA 8 RDB 8 RDB
SDB 6 RDA 6 RDA
CA3-ADPTRM-01 TERMRX Shell FG Shell FG
SG
FG
User-created cable
3D)
• 1:1 connection
External Device side
Termination D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
resistance Signal Signal
Pin name Pin name
Display 220Ω 1/4W
2 RDA 2 SDB
7 RDB 1 SDA
3 SDA 8 RDB
CA4-ADPONL-01 8 SDB 6 RDA
Shell FG
User-created cable
• 1:n connection
External Device side External Device side
Termination D-sub 9 pin (plug) Shield D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
resistance Signal Signal Signal
Pin name Pin name
Pin name
Display 220Ω 1/4W
2 RDA 2 SDB 2 SDB
7 RDB 1 SDA 1 SDA
3 SDA 8 RDB 8 RDB
CA4-ADPONL-01 8 SDB 6 RDA 6 RDA
Shell FG Shell FG
User-created cable
3E)
• 1:1 connection
Display side External Device side
Terminal block Shield D-sub 9 pin (plug)
Termination Signal Pin Signal name
name
resistance*1
RDA 2 SDB
Display RDB 1 SDA
SDA 8 RDB
SDB 6 RDA
CSB Shell FG
ERB
CSA
ERA
• 1:n connection
Display side External Device side External Device side
Terminal block Shield D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
Termination Signal
resistance*1 name Pin Signal name Pin Signal name
RDA 2 SDB 2 SDB
Display RDB 1 SDA 1 SDA
SDA 8 RDB 8 RDB
SDB
6 RDA 6 RDA
CSB Shell FG Shell FG
ERB
CSA
ERA
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
3F)
• 1:1 connection
Terminal External Device side
block Shield D-sub 9 pin (plug)
Termination Signal Signal
resistance Pin name
name
220Ω 1/4W
RDA 2 SDB
Display RDB 1 SDA
SDA 8 RDB
SDB 6 RDA
PFXZCBADTM1 TERMRX Shell FG
SG
FG
User-created cable
• 1:n connection
Terminal External Device side External Device side
block Shield D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
Termination Signal Signal Signal
resistance Pin name
Pin name
name
220Ω 1/4W RDA SDB 2 SDB
2
Display RDB 1 SDA 1 SDA
SDA 8 RDB 8 RDB
SDB 6 RDA 6 RDA
PFXZCBADTM1 TERMRX Shell FG Shell FG
SG
FG
User-created cable
3G)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield D-sub 9 pin (plug)
Termination
resistance Signal Signal name
Pin name Pin
220Ω 1/4W
3 Rx+ 2 SDB
Display 4 Rx+ 1 SDA
2 Tx+ 8 RDB
1 Tx- 6 RDA
6 NC Shell FG
9 NC
8 NC
7 NC
• 1:n connection
Display side External Device side
Shield External Device side
Termination D-sub 9 pin (socket) D-sub 9 pin (plug) Shield D-sub 9 pin (plug)
resistance Signal
Pin Signal name Signal name
220Ω 1/4W name Pin Pin
3 Rx+ 2 SDB 2 SDB
Display 4 Rx- 1 SDA 1 SDA
2 Tx+ 8 RDB 8 RDB
1 Tx- 6 RDA 6 RDA
6 NC Shell FG Shell FG
9 NC
8 NC
7 NC
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
Displayy
Cable Notes
(Connection Port)
COM Port Conversion Adapter by Pro-face
CA3-ADPCOM-01
+
4A Terminal Block Conversion Adapter by Pro-face
GP3000*1 (COM1) CA3-ADPTRM-01
AGP-3302B (COM2) +
GP-4*01TM (COM1) User-created cable
GP-Rear Module (COM1) The cable length must be
ST3000*2 (COM2) COM Port Conversion Adapter by Pro-face 500m or less.
LT3000 (COM1) CA3-ADPCOM-01
IPC*3 +
4B Multi-Link Cable (5m) by Pro-face
CA3-CBLMLT-01
+
User-created cable
4C User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
+
4D Terminal Block Conversion Adapter by Pro-face
CA3-ADPTRM-01
+
User-created cable
Online Adapter by Pro-face
*1 CA4-ADPONL-01 The cable length must be
GP3000 (COM2)
+ 500m or less.
4E Multi-Link Cable (5m) by Pro-face
CA3-CBLMLT-01
+
User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
4F
+
User-created cable
GP-4106 (COM1)
The cable length must be
GP-4116T (COM1) 4G User-created cable
500m or less.
Displayy
Cable Notes
(Connection Port)
RS-422 Terminal Block Conversion Adapter by
Pro-face
GP4000*4 (COM2) PFXZCBADTM1
4H *7
GP-4201T (COM1)
SP5000*5 (COM1/2) +
SP-5B00 (COM2) User-created cable
The cable length must be
ST6000*6 (COM2)
Multi-Link Cable (5m) by Pro-face 500m or less.
ST-6200 (COM1)
STM6000 (COM1) PFXZCBCBML1
4I *8
+
User-created cable
4C User-created cable
*9
PE-4000B
The cable length must be
PS5000*9 4J User-created cable
500m or less.
PS6000*9
*1 All GP3000 models except AGP-3302B
*2 Except AST-3211A and AST-3302B
*3 Only the COM port which can communicate by RS-422/485 (4 wire) can be used. (Except PE-4000B, PS5000,
and PS6000)
IPC COM Port (page 10)
*4 All GP4000 models except GP-4100 series, GP-4*01TM, GP-Rear Module, GP-4201T and GP-4*03T
*5 Except SP-5B00
*6 Except ST-6200
*7 When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block
Conversion Adapter, refer to Cable Diagram 4A.
*8 When using a Multilink Cable (CA3-CBLMLT-01) instead of the Multilink Cable, refer to Cable Diagram 4B.
*9 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
IPC COM Port (page 10)
4A)
• n:1 connection
CA3-ADPTRM-01 CA3-ADPTRM-01
CA3-ADPCOM-01 CA3-ADPCOM-01
Display Display
User-created cable
4B)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) D-Sub 9 pin (plug)
Termination Shield
resistance Signal name Signal name Pin Signal name
220Ω 1/4W
RDA RDA 2 SDB
RDB RDB 1 SDA
SDA SDA 8 RDB
SDB SDB 6 RDA
Connector
SG SG shell FG
FG FG
CA3-CBLMLT-01 CA3-CBLMLT-01
CA3-ADPCOM-01 CA3-ADPCOM-01
Display Display
User-created cable
4C)
• n:1 connection
Display side Terminal block Terminal block External Device side
D-sub 9 pin (socket) (M3 screw) (M3 screw) D-Sub 9 pin (plug)
Termination
resistance Pin Signal name Signal name Signal name Pin Signal name
220Ω 1/4W
1 RDA RDA RDA 2 SDB
2 RDB RDB RDB 1 SDA
Display 3 SDA SDA SDA 8 RDB
7 SDB SDB SDB 6 RDA
5 SG SG SG Connector
shell FG
4 ERA FG FG
8 CSA
9 ERB
6 CSB
Shell FG
Display side
D-sub 9 pin (socket)
1 RDA RDA
2 RDB RDB
Display SDA
3 SDA
7 SDB SDB
5 SG SG
4 ERA FG
8 CSA
9 ERB
6 CSB
Shell FG
4D)
• n:1 connection
Terminal Terminal External Device side
block Shield block D-Sub 9 pin (plug)
Termination Shield
resistance Signal name Signal name Pin Signal name
220Ω 1/4W
RDA RDA 2 SDB
RDB RDB 1 SDA
SDA SDA 8 RDB
SDB SDB 6 RDA
SG SG Connector FG
shell
TRM FG
CA3-ADPTRM-01 CA3-ADPTRM-01
CA4-ADPONL-01 CA4-ADPONL-01
Display Display
User-created cable
4E)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) D-Sub 9 pin (plug)
Termination Shield
resistance Signal name Signal name Pin Signal name
220Ω 1/4W
RDA RDA 2 SDB
RDB RDB 1 SDA
SDA SDA 8 RDB
SDB SDB 6 RDA
SG SG Connector FG
shell
FG FG
CA3-CBLMLT-01 CA3-CBLMLT-01
CA4-ADPONL-01 CA4-ADPONL-01
Display Display
User-created cable
4F)
• n:1 connection
Terminal block Terminal block External Device side
D-sub 9 pin (plug) (M3 screw) (M3 screw) D-Sub 9 pin (plug)
Termination
resistance Pin Signal name Signal name Signal name Pin Signal name
220Ω 1/4W
2 RDA RDA RDA 2 SDB
7 RDB RDB RDB 1 SDA
Display 3 SDA SDA SDA 8 RDB
8 SDB SDB SDB 6 RDA
5 SG SG SG Connector
shell FG
CA4-ADPONL-01 Shell FG FG FG
2 RDA RDA
7 RDB RDB
Display 3 SDA SDA
8 SDB SDB
5 SG SG
CA4-ADPONL-01 Shell FG FG
4G)
• n:1 connection
Display side Display side External Device side
Terminal block Terminal block D-Sub 9 pin (plug)
Termination Signal name Signal name Pin Signal name
resistance*1
RDA RDA 2 SDB
RDB RDB 1 SDA
SDA SDA 8 RDB
SDB SDB 6 RDA
SG SG Connector
shell FG
ERA ERA
CSA CSA
ERB ERB
CSB CSB
Display Display
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
For the Display other than that used as the terminal, set the DIP Switch 1-4 on the rear of the Display to
OFF in the n:1 connection.
4H)
• n:1 connection
PFXZCBADTM1 PFXZCBADTM1
Display Display
User-created cable
4I)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) D-Sub 9 pin (plug)
Termination Shield
resistance Signal name Signal name Pin Signal name
220Ω 1/4W
RDA RDA 2 SDB
RDB RDB 1 SDA
SDA SDA 8 RDB
SDB SDB 6 RDA
Connector
SG SG shell FG
FG FG
PFXZCBCBML1 PFXZCBCBML1
Display Display
User-created cable
4J)
• n:1 connection
Display side Terminal block Terminal block External Device side
D-sub 9 pin (socket) (M3 screw) (M3 screw) D-Sub 9 pin (plug)
Termination
resistance Pin Signal name Signal name Signal name Pin Signal name
220Ω 1/4W
3 Rx+ Rx+ Rx+ 2 SDB
4 Rx- Rx- Rx- 1 SDA
Display 2 Tx+ Tx+ Tx+ 8 RDB
1 Tx- Tx- Tx- 6 RDA
5 GND GND GND Connector
shell FG
7 NC FG FG
8 NC
9 NC
6 NC
Shell FG
Display side
D-sub 9 pin (socket)
3 Rx+ Rx+
4 Rx- Rx-
Display Tx+ Tx+
2
1 Tx- Tx-
5 GND GND
7 NC FG
8 NC
9 NC
6 NC
Shell FG
Display
Cable Notes
(Connection Port)
5B User-created cable
*8 When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block
Conversion Adapter, refer to Cable Diagram 5A.
*9 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
IPC COM Port (page 10)
5A)
• 1:1 connection
Terminal External Device side
block Shield Terminal block
Termination Signal Signal
resistance name name
220Ω 1/4W
RDA SDB+
Display RDB SDA-
CA3-ADPCOM-01
SDA RDB+
SDB RDA-
CA3-ADPTRM-01 TERMRX FG
SG
FG
User-created cable
• 1:n connection
Terminal External Device side External Device side
block Shield Terminal block Shield Terminal block
Termination Signal Signal Signal
resistance name name name
220Ω 1/4W RDA SDB+ SDB+
Display RDB SDA- SDA-
CA3-ADPCOM-01
SDA RDB+ RDB+
SDB RDA- RDA-
CA3-ADPTRM-01 TERMRX FG FG
SG
FG
User-created cable
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
5B)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination
resistance Signal Signal name
Pin name
220Ω 1/4W
1 RDA SDB+
Display 2 RDB SDA-
3 SDA RDB+
7 SDB RDA-
6 CSB FG
9 ERB
8 CSA
4 ERA
• 1:n connection
Display side External Device side
Shield External Device side
Termination D-sub 9 pin (socket) Terminal block Shield Terminal block
resistance Signal
Pin name Signal name Signal name
220Ω 1/4W
1 RDA SDB+ SDB+
Display 2 RDB SDA- SDA-
3 SDA RDB+ RDB+
7 SDB RDA- RDA-
6 CSB FG FG
9 ERB
8 CSA
4 ERA
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
5C)
• 1:1 connection
External Device side
Terminal block Shield Terminal block
Termination Signal Signal
resistance name name
220Ω 1/4W RDA SDB+
Display RDB SDA-
CA4-ADPONL-01
SDA RDB+
SDB RDA-
CA3-ADPTRM-01 TERMRX FG
SG
FG
User-created cable
• 1:n connection
External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
Termination
resistance Signal Signal Signal
name name name
220Ω 1/4W
RDA SDB+ SDB+
Display RDB SDA- SDA-
CA4-ADPONL-01
SDA RDB+ RDB+
SDB RDA- RDA-
CA3-ADPTRM-01 TERMRX FG FG
SG
FG
User-created cable
5D)
• 1:1 connection
External Device side
Termination D-sub 9 pin (plug) Shield Terminal block
resistance Signal Signal
Pin name name
Display 220Ω 1/4W
2 RDA SDB+
7 RDB SDA-
3 SDA RDB+
CA4-ADPONL-01 8 SDB RDA-
FG
User-created cable
• 1:n connection
External Device side External Device side
Termination D-sub 9 pin (plug) Shield Terminal block Shield Terminal block
resistance Pin Signal Signal Signal
220Ω 1/4W name name name
Display
2 RDA SDB+ SDB+
7 RDB SDA- SDA-
3 SDA RDB+ RDB+
CA4-ADPONL-01 8 SDB RDA- RDA-
FG FG
User-created cable
5E)
• 1:1 connection
Display side External Device side
Terminal block Shield Terminal block
Termination Signal Signal name
name
resistance*1
RDA SDB+
Display RDB SDA-
SDA RDB+
SDB RDA-
CSB FG
ERB
CSA
ERA
• 1:n connection
Display side External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
Termination Signal
resistance*1 name Signal name Signal name
RDA SDB+ SDB+
Display RDB SDA- SDA-
SDA RDB+ RDB+
SDB RDA- RDA-
CSB FG FG
ERB
CSA
ERA
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
5F)
• 1:1 connection
Terminal External Device side
block Shield Terminal block
Termination Signal Signal
resistance name name
220Ω 1/4W
RDA SDB+
Display RDB SDA-
SDA RDB+
SDB RDA-
PFXZCBADTM1 TERMRX FG
SG
FG
User-created cable
• 1:n connection
Terminal External Device side External Device side
block Shield Terminal block Shield Terminal block
Termination Signal Signal Signal
resistance name name name
220Ω 1/4W RDA SDB+ SDB+
Display RDB SDA- SDA-
SDA RDB+ RDB+
SDB RDA- RDA-
PFXZCBADTM1 TERMRX FG FG
SG
FG
User-created cable
5G)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination
resistance Signal Signal name
Pin name
220Ω 1/4W
3 Rx+ SDB+
Display 4 Rx+ SDA-
2 Tx+ RDB+
1 Tx- RDA-
6 NC FG
9 NC
8 NC
7 NC
• 1:n connection
Display side External Device side
Shield External Device side
Termination D-sub 9 pin (socket) Terminal block Shield Terminal block
resistance Signal
Pin name Signal name Signal name
220Ω 1/4W
3 Rx+ SDB+ SDB+
Display 4 Rx- SDA- SDA-
2 Tx+ RDB+ RDB+
1 Tx- RDA- RDA-
6 NC FG FG
9 NC
8 NC
7 NC
• When the display unit you use is an IPC, turn ON the DIP switch 6 to insert the termination
resistance.
• The cable length must be 500m or less.
Displayy
Cable Notes
(Connection Port)
COM Port Conversion Adapter by Pro-face
CA3-ADPCOM-01
+
6A Terminal Block Conversion Adapter by Pro-face
GP3000*1 (COM1) CA3-ADPTRM-01
AGP-3302B (COM2) +
GP-4*01TM (COM1) User-created cable
GP-Rear Module (COM1) The cable length must be
ST3000*2 (COM2) COM Port Conversion Adapter by Pro-face 500m or less.
LT3000 (COM1) CA3-ADPCOM-01
IPC*3 +
6B Multi-Link Cable (5m) by Pro-face
CA3-CBLMLT-01
+
User-created cable
6C User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
+
6D Terminal Block Conversion Adapter by Pro-face
CA3-ADPTRM-01
+
User-created cable
Online Adapter by Pro-face
*1 CA4-ADPONL-01 The cable length must be
GP3000 (COM2)
+ 500m or less.
6E Multi-Link Cable (5m) by Pro-face
CA3-CBLMLT-01
+
User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
6F
+
User-created cable
GP-4106 (COM1)
The cable length must be
GP-4116T (COM1) 6G User-created cable
500m or less.
Displayy
Cable Notes
(Connection Port)
RS-422 Terminal Block Conversion Adapter by
Pro-face
GP4000*4 (COM2) PFXZCBADTM1
6H *7
GP-4201T (COM1)
SP5000*5 (COM1/2) +
SP-5B00 (COM2) User-created cable
The cable length must be
ST6000*6 (COM2)
Multi-Link Cable (5m) by Pro-face 500m or less.
ST-6200 (COM1)
STM6000 (COM1) PFXZCBCBML1
6I *8
+
User-created cable
6C User-created cable
*9
PE-4000B
The cable length must be
PS5000*9 6J User-created cable
500m or less.
PS6000*9
*1 All GP3000 models except AGP-3302B
*2 Except AST-3211A and AST-3302B
*3 Only the COM port which can communicate by RS-422/485 (4 wire) can be used. (Except PE-4000B, PS5000,
and PS6000)
IPC COM Port (page 10)
*4 All GP4000 models except GP-4100 series, GP-4*01TM, GP-Rear Module, GP-4201T and GP-4*03T
*5 Except SP-5B00
*6 Except ST-6200
*7 When using a Terminal Block Conversion Adapter (CA3-ADPTRM-01) instead of the RS-422 Terminal Block
Conversion Adapter, refer to Cable Diagram 6A.
*8 When using a Multilink Cable (CA3-CBLMLT-01) instead of the Multilink Cable, refer to Cable Diagram 6B.
*9 Only the COM port which can communicate by RS-422/485 (4 wire) can be used.
IPC COM Port (page 10)
6A)
• n:1 connection
Terminal Terminal External Device side
block Shield block Shield Terminal block
Termination
resistance Signal name Signal name Signal name
220Ω 1/4W
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
TRM FG
CA3-ADPTRM-01 CA3-ADPTRM-01
CA3-ADPCOM-01 CA3-ADPCOM-01
Display Display
User-created cable
6B)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) Terminal block
Termination Shield
resistance Signal name Signal name Signal name
220Ω 1/4W
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
FG FG
CA3-CBLMLT-01 CA3-CBLMLT-01
CA3-ADPCOM-01 CA3-ADPCOM-01
Display Display
User-created cable
6C)
• n:1 connection
Display side Terminal block Terminal block External Device side
D-sub 9 pin (socket) (M3 screw) (M3 screw) Terminal block
Termination
resistance Pin Signal name Signal name Signal name Signal name
220Ω 1/4W
1 RDA RDA RDA SDB+
2 RDB RDB RDB SDA-
Display 3 SDA SDA SDA RDB+
7 SDB SDB SDB RDA-
5 SG SG SG FG
4 ERA FG FG
8 CSA
9 ERB
6 CSB
Shell FG
Display side
D-sub 9 pin (socket)
1 RDA RDA
2 RDB RDB
Display SDA
3 SDA
7 SDB SDB
5 SG SG
4 ERA FG
8 CSA
9 ERB
6 CSB
Shell FG
6D)
• n:1 connection
Terminal Terminal External Device side
block Shield block Terminal block
Termination Shield
resistance Signal name Signal name Signal name
220Ω 1/4W
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
TRM FG
CA3-ADPTRM-01 CA3-ADPTRM-01
CA4-ADPONL-01 CA4-ADPONL-01
Display Display
User-created cable
6E)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) Terminal block
Termination Shield
resistance Signal name Signal name Signal name
220Ω 1/4W
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
FG FG
CA3-CBLMLT-01 CA3-CBLMLT-01
CA4-ADPONL-01 CA4-ADPONL-01
Display Display
User-created cable
6F)
• n:1 connection
Terminal block Terminal block External Device side
D-sub 9 pin (plug) (M3 screw) (M3 screw) Terminal block
Termination
resistance Pin Signal name Signal name Signal name Signal name
220Ω 1/4W
2 RDA RDA RDA SDB+
7 RDB RDB RDB SDA-
Display 3 SDA SDA SDA RDB+
8 SDB SDB SDB RDA-
5 SG SG SG FG
CA4-ADPONL-01 Shell FG FG FG
2 RDA RDA
7 RDB RDB
Display 3 SDA SDA
8 SDB SDB
5 SG SG
CA4-ADPONL-01 Shell FG FG
6G)
• n:1 connection
Display side Display side External Device side
Terminal block Terminal block Terminal block
Termination Signal name Signal name Signal name
resistance*1
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
ERA ERA
CSA CSA
ERB ERB
CSB CSB
Display Display
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
For the Display other than that used as the terminal, set the DIP Switch 1-4 on the rear of the Display to
OFF in the n:1 connection.
6H)
• n:1 connection
PFXZCBADTM1 PFXZCBADTM1
Display Display
User-created cable
6I)
• n:1 connection
Terminal Terminal
block block External Device side
(M3 screw) Shield (M3 screw) Terminal block
Termination Shield
resistance Signal name Signal name Signal name
220Ω 1/4W
RDA RDA SDB+
RDB RDB SDA-
SDA SDA RDB+
SDB SDB RDA-
SG SG FG
FG FG
PFXZCBCBML1 PFXZCBCBML1
Display Display
User-created cable
6J)
• n:1 connection
Display side Terminal block Terminal block External Device side
D-sub 9 pin (socket) (M3 screw) (M3 screw) Terminal block
Termination
resistance Pin Signal name Signal name Signal name Signal name
220Ω 1/4W
3 Rx+ Rx+ Rx+ SDB+
4 Rx- Rx- Rx- SDA-
Display 2 Tx+ Tx+ Tx+ RDB+
1 Tx- Tx- Tx- RDA-
5 GND GND GND FG
7 NC FG FG
8 NC
9 NC
6 NC
Shell FG
Display side
D-sub 9 pin (socket)
3 Rx+ Rx+
4 Rx- Rx-
Display Tx+ Tx+
2
1 Tx- Tx-
5 GND GND
7 NC FG
8 NC
9 NC
6 NC
Shell FG
Display
Cable Notes
(Connection Port)
COM Port Conversion Adapter by Pro-face
GP3000*1 (COM1) CA3-ADPCOM-01
AGP-3302B (COM2) +
GP-4*01TM (COM1) 7A Terminal Block Conversion Adapter by Pro-face The cable length
GP-Rear Module CA3-ADPTRM-01 must be 500m or
(COM1) + less.
ST3000*2 (COM2) User-created cable
LT3000 (COM1)
7B User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
+
7C Terminal Block Conversion Adapter by Pro-face
CA3-ADPTRM-01 The cable length
GP3000*3 (COM2) + must be 500m or
User-created cable less.
Online Adapter by Pro-face
CA4-ADPONL-01
7D
+
User-created cable
COM Port Conversion Adapter by Pro-face
CA3-ADPCOM-01
+
7E Terminal Block Conversion Adapter by Pro-face The cable length
IPC*4
CA3-ADPTRM-01 must be 500m or
+ less.
User-created cable
7F User-created cable
GP-4106 (COM1) The cable length
GP-4116T (COM1) 7G User-created cable must be 500m or
less.
GP-4107 (COM1)
The cable length
GP-4*03T*5 (COM2)
7H User-created cable must be 500m or
GP-4203T (COM1)
less.
LT-4*01TM (COM1)
RJ45 RS-485 Cable (5m) by Pro-face The cable length
LT-Rear Module
7J PFXZLMCBRJR81 must be 500m or
(COM1)
less.
7A)
• 1:1 connection
Display side
Terminal block Shield
User-created cable
• 1:n connection
Display side
Terminal block
Termination Signal name Shield Shield
resistance External Device side External Device side
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
CA3-ADPCOM-01
SDA B(+) B(+)
SDB A(-) A(-)
CA3-ADPTRM-01 SG FG FG
FG
User-created cable
7B)
• 1:1 connection
Display side
D-sub 9 pin (socket) Shield
Termination Pin Signal name
resistance External Device side
220Ω 1 RDA Terminal block
Display 2 RDB Signal name
3 SDA B(+)
7 SDB A(-)
5 SG FG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
• 1:n connection
Display side
D-sub 9 pin (socket) Shield
Termination Pin Signal name Shield
resistance External Device side External Device side
220Ω 1 RDA Terminal block Terminal block
Display 2 RDB Signal name Signal name
3 SDA B(+) B(+)
7 SDB A(-) A(-)
5 SG FG FG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
7C)
• 1:1 connection
Display side
Terminal block
Termination Shield
Signal name
resistance External Device side
220Ω RDA Terminal block
Display RDB Signal name
CA4-ADPONL-01
SDA B(+)
SDB A(-)
CA3-ADPTRM-01 SG FG
FG
User-created cable
• 1:n connection
Display side
Terminal block
Termination Signal name
Shield Shield
resistance External Device side External Device side
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
CA4-ADPONL-01
SDA B(+) B(+)
SDB A(-) A(-)
CA3-ADPTRM-01 SG FG FG
FG
User-created cable
7D)
• 1:1 connection
Display side
D-sub 9 pin (plug)
Termination Shield
Pin Signal name
resistance External Device side
220Ω 2 RDA Terminal block
Display 7 RDB Signal name
3 SDA B(+)
8 SDB A(-)
CA4-ADPONL-01 5 SG FG
Shell FG
User-created cable
• 1:n connection
Display side
D-sub 9 pin (plug)
Termination Shield Shield
Pin Signal name
resistance External Device side External Device side
220Ω 2 RDA Terminal block Terminal block
Display 7 RDB Signal name Signal name
3 SDA B(+) B(+)
8 SDB A(-) A(-)
CA4-ADPONL-01 5 SG FG FG
Shell FG
User-created cable
7E)
• 1:1 connection
Display side External Device side
Terminal block Shield Terminal block
Termination Signal name Signal name
resistance
220Ω RDA B(+)
Display RDB A(-)
CA3-ADPCOM-01
SDA FG
SDB
CA3-ADPTRM-01 SG
FG
User-created cable
• 1:n connection
Display side External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
Termination Signal name Signal name Signal name
resistance
220Ω RDA B(+) B(+)
Display RDB A(-) A(-)
CA3-ADPCOM-01
SDA FG FG
SDB
CA3-ADPTRM-01 SG
FG
User-created cable
7F)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 1 DATA+ B(+)
Display 2 DATA- A(-)
3 NC FG
7 NC
5 SG(GND)
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination Pin Signal name Signal name Signal name
resistance
220Ω 1 DATA+ B(+) B(+)
Display 2 DATA- A(-) A(-)
3 NC FG FG
7 NC
5 SG(GND)
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
7G)
• 1:1 connection
Display side External Device side
Terminal block Shield Terminal block
• 1:n connection
Display side External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
7H)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 3 LINE+ B(+)
Display 8 LINE- A(-)
5 SG(GND) FG
1 NC
2 NC
4 RS(RTS)
6 5V
7 NC
9 NC
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination Pin Signal name Signal name Signal name
resistance
220Ω 3 LINE+ B(+) B(+)
Display 8 LINE- A(-) A(-)
5 SG(GND) FG FG
1 NC
2 NC
4 RS(RTS)
6 5V
7 NC
9 NC
Shell FG
7I)
• 1:1 connection
Display side
Terminal block
Termination Signal name Shield
resistance External Device side
220Ω RDA Terminal block
Display RDB Signal name
SDA B(+)
SDB A(-)
PFXZCBADTM1 SG FG
FG
User-created cable
• 1:n connection
Display side
Terminal block
Termination Signal name Shield Shield
resistance
External Device side External Device side
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
SDA B(+) B(+)
SDB A(-) A(-)
PFXZCBADTM1 SG FG FG
FG
User-created cable
7J)
• 1:1 connection
External Device side
Terminal block
• 1:n connection
External Device side External Device side
Terminal block Shield Terminal block
7K)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 2 DATA+ B(+)
Display 1 DATA- A(-)
3 NC FG
7 NC
5 GND
4 NC
8 NC
9 NC
6 NC
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination Pin Signal name Signal name Signal name
resistance
220Ω 2 DATA+ B(+) B(+)
Display 1 DATA- A(-) A(-)
3 NC FG FG
7 NC
5 GND
4 NC
8 NC
9 NC
6 NC
Shell FG
Display
Cable Notes
(Connection Port)
COM Port Conversion Adapter by Pro-face
GP3000*1 (COM1) CA3-ADPCOM-01
AGP-3302B (COM2) +
GP-4*01TM (COM1) 8A Terminal Block Conversion Adapter by Pro-face The cable length
GP-Rear Module CA3-ADPTRM-01 must be 500m or
(COM1) + less.
ST3000*2 (COM2) User-created cable
LT3000 (COM1)
8B User-created cable
Online Adapter by Pro-face
CA4-ADPONL-01
+
8C Terminal Block Conversion Adapter by Pro-face
CA3-ADPTRM-01 The cable length
GP3000*3 (COM2) + must be 500m or
User-created cable less.
Online Adapter by Pro-face
CA4-ADPONL-01
8D
+
User-created cable
COM Port Conversion Adapter by Pro-face
CA3-ADPCOM-01
+
8E Terminal Block Conversion Adapter by Pro-face The cable length
IPC*4
CA3-ADPTRM-01 must be 500m or
+ less.
User-created cable
8F User-created cable
GP-4106 (COM1) The cable length
GP-4116T (COM1) 8G User-created cable must be 500m or
less.
GP-4107 (COM1)
The cable length
GP-4*03T*5 (COM2)
8H User-created cable must be 500m or
GP-4203T (COM1)
less.
LT-4*01TM (COM1)
RJ45 RS-485 Cable (5m) by Pro-face The cable length
LT-Rear Module
8J PFXZLMCBRJR81 must be 500m or
(COM1)
less.
8A)
• 1:1 connection
Display side
Terminal block Shield
Termination Signal name
resistance External Device side
220Ω RDA Terminal block
Display RDB Signal name
CA3-ADPCOM-01
SDA SDA-
SDB SDB+
CA3-ADPTRM-01 SG FG
FG
User-created cable
• 1:n connection
Display side
Terminal block
Termination Signal name Shield Shield
resistance External Device side External Device side
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
CA3-ADPCOM-01
SDA SDA- SDA-
SDB SDB+ SDB+
CA3-ADPTRM-01 SG FG FG
FG
User-created cable
8B)
• 1:1 connection
Display side
D-sub 9 pin (socket) Shield
Termination Pin Signal name
resistance External Device side
220Ω 1 RDA Terminal block
Display 2 RDB Signal name
3 SDA SDA-
7 SDB SDB+
5 SG FG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
• 1:n connection
Display side
D-sub 9 pin (socket) Shield
Termination Pin Signal name Shield
resistance External Device side External Device side
220Ω 1 RDA Terminal block Terminal block
Display 2 RDB Signal name Signal name
3 SDA SDA- SDA-
7 SDB SDB+ SDB+
5 SG FG FG
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
8C)
• 1:1 connection
Display side
Terminal block
Termination Signal name
Shield
resistance External Device side
220Ω RDA Terminal block
Display RDB Signal name
CA4-ADPONL-01
SDA SDA-
SDB SDB+
CA3-ADPTRM-01 SG FG
FG
User-created cable
• 1:n connection
Display side
Terminal block
Shield Shield
Termination Signal name
External Device side External Device side
resistance
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
CA4-ADPONL-01
SDA SDA- SDA-
SDB SDB+ SDB+
CA3-ADPTRM-01 SG FG FG
FG
User-created cable
8D)
• 1:1 connection
Display side
D-sub 9 pin (plug)
Termination
Shield
Pin Signal name
resistance External Device side
220Ω 2 RDA Terminal block
Display 7 RDB Signal name
3 SDA SDA-
8 SDB SDB+
CA4-ADPONL-01 5 SG FG
Shell FG
User-created cable
• 1:n connection
Display side
D-sub 9 pin (plug)
Shield Shield
Termination Pin Signal name
resistance External Device side External Device side
220Ω 2 RDA Terminal block Terminal block
Display 7 RDB Signal name Signal name
3 SDA SDA- SDA-
8 SDB SDB+ SDB+
CA4-ADPONL-01 5 SG FG FG
Shell FG
User-created cable
8E)
• 1:1 connection
Display side External Device side
Terminal block Shield Terminal block
Termination Signal name Signal name
resistance
220Ω RDA SDA-
Display RDB SDB+
CA3-ADPCOM-01
SDA FG
SDB
CA3-ADPTRM-01 SG
FG
User-created cable
• 1:n connection
Display side External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
Termination Signal name Signal name Signal name
resistance
220Ω RDA SDA-
B(+) SDA-
Display RDB SDB+
A(-) SDB+
CA3-ADPCOM-01
SDA FG FG
SDB
CA3-ADPTRM-01 SG
FG
User-created cable
8F)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 1 DATA+ SDA-
Display 2 DATA- SDB+
3 NC FG
7 NC
5 SG(GND)
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination Pin Signal name Signal name Signal name
resistance
220Ω 1 DATA+ SDA- SDA-
Display 2 DATA- SDB+ SDB+
3 NC FG FG
7 NC
5 SG(GND)
4 ERA
8 CSA
9 ERB
6 CSB
Shell FG
8G)
• 1:1 connection
Display side External Device side
Terminal block Shield Terminal block
Termination Signal name Signal name
resistance *1
RDA SDA-
Display RDB SDB+
SDA FG
SDB
SG
ERA
CSA
ERB
CSB
• 1:n connection
Display side External Device side External Device side
Terminal block Shield Terminal block Shield Terminal block
*1 The resistance in the Display is used as the termination resistance. Set the value of the DIP Switch on the
rear of the Display as shown in the table below.
8H)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 3 LINE+ SDA-
Display 8 LINE- SDB+
5 SG(GND) FG
1 NC
2 NC
4 RS(RTS)
6 5V
7 NC
9 NC
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination Pin Signal name Signal name Signal name
resistance
220Ω 3 LINE+ SDA- SDA-
Display 8 LINE- SDB+ SDB+
5 SG(GND) FG FG
1 NC
2 NC
4 RS(RTS)
6 5V
7 NC
9 NC
Shell FG
8I)
• 1:1 connection
Display side
Terminal block
Signal name Shield
Termination
External Device side
resistance
220Ω RDA Terminal block
Display RDB Signal name
SDA SDA-
SDB SDB+
PFXZCBADTM1 SG FG
FG
User-created cable
• 1:n connection
Display side
Terminal block
Termination Signal name
Shield Shield
resistance
External Device side External Device side
220Ω RDA Terminal block Terminal block
Display RDB Signal name Signal name
SDA SDA- SDA-
SDB SDB+ SDB+
PFXZCBADTM1 SG FG FG
FG
User-created cable
8J)
• 1:1 connection
External Device side
Terminal block
• 1:n connection
External Device side External Device side
Terminal block Shield Terminal block
8K)
• 1:1 connection
Display side External Device side
D-sub 9 pin (socket) Shield Terminal block
Termination Pin Signal name Signal name
resistance
220Ω 2 DATA+ SDA-
Display 1 DATA- SDB+
3 NC FG
7 NC
5 GND
4 NC
8 NC
9 NC
6 NC
Shell FG
• 1:n connection
Display side External Device side External Device side
D-sub 9 pin (socket) Shield Terminal block Shield Terminal block
Termination
Pin Signal name Signal name Signal name
resistance
220Ω 2 DATA+ SDA- SDA-
Display 1 DATA- SDB+ SDB+
3 NC FG FG
7 NC
5 GND
4 NC
8 NC
9 NC
6 NC
Shell FG
Display
Cable Notes
(Connection Port)
GP3000 (COM1)
GP4000*1 (COM1)
SP5000*2 (COM1/2)
SP-5B00 (COM1)
ST3000 (COM1) The cable length must
9A User-created cable
ST6000 (COM1) be 15m or less.
STM6000 (COM1)
LT3000 (COM1)
IPC*3
PC/AT
GP-4105 (COM1)
GP-4115T (COM1) The cable length must
9B User-created cable
GP-4115T3 (COM1) be 15m or less.
LT-4*01TM (COM1)
RJ45 RS-232C Cable (5m) by Pro-face
LT-Rear Module The cable length must
9C PFXZLMCBRJR21
(COM1) be 5m or less.
9A)
Display side External Device side
D-sub 9 pin (socket) Terminal block
Pin Signal name Shield Pin Signal name
Display 2 RD(RXD) 1 SD(TXD)
3 SD(TXD) 2 RD(RXD)
5 SG 3 RS(RTS)
7 RS(RTS) 4 CS(CTS)
8 CS(CTS) 5 SG
6 FG
9B)
Display side External Device side
Terminal block Terminal block
Signal name Shield Pin Signal name
Display RD(RXD) 1 SD(TXD)
SD(TXD) 2 RD(RXD)
SG 3 RS(RTS)
RS(RTS) 4 CS(CTS)
CS(CTS) 5 SG
6 FG
9C)
External Device side
Terminal block
Pin Signal name
Display RXD
1 SD(TXD)
TXD RD(RXD)
2
(1) 3 RS(RTS)
4 CS(CTS)
GND
5 SG
6 FG
Display
Cable Notes
(Connection Port)
GP3000 (COM1)
GP4000*1 (COM1)
SP5000*2 (COM1/2)
SP-5B00 (COM1)
ST3000 (COM1) The cable length must
10A User-created cable
ST6000 (COM1) be 15m or less.
STM6000 (COM1)
LT3000 (COM1)
IPC*3
PC/AT
GP-4105 (COM1)
GP-4115T (COM1) The cable length must
10B User-created cable
GP-4115T3 (COM1) be 15m or less.
LT-4*01TM (COM1)
RJ45 RS-232C Cable (5m) by Pro-face
LT-Rear Module The cable length must
10C PFXZLMCBRJR21
(COM1) be 5m or less.
10A)
Display side External Device side
D-sub 9 pin (socket) Terminal block
Shield
Pin Signal name Pin Signal name
Display 2 RD(RXD) 1 SD(TXD)
3 SD(TXD) 2 RD(RXD)
5 SG 3 SG
7 RS(RTS) 4 FG
8 CS(CTS) 5 SD(TXD)
6 RD(RXD)
7 SG
8 FG
10B)
Display side External Device side
Terminal block Terminal block
Shield
Signal name Pin Signal name
Display RD(RXD) 1 SD(TXD)
SD(TXD) 2 RD(RXD)
SG 3 SG
RS(RTS) 4 FG
CS(CTS) 5 SD(TXD)
6 RD(RXD)
7 SG
8 FG
10C)
External Device side
Terminal block
Pin Signal name
Display RXD
1 SD(TXD)
TXD RD(RXD)
2
GND
(1) 3 SG
4 FG
5 SD(TXD)
6 RD(RXD)
7 SG
8 FG
6 Supported Device
Range of supported device address is shown in the table below. Please note that the actually supported range of
the devices varies depending on the External Device to be used. Please check the actual range in the manual of
your External Device.
Timer *2
T0000-T4095 -
(Time Up Flag)
Counter *2
C0000-C4095 -
(Count Up Flag)
Task Flag *2
TKB00-TKB31 -
(Bit)
Task Flag
TK00.00-TK31.07 TK00-TK30 *2
(Status)
• Please refer to the GP-Pro EX Reference Manual for system data area.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
• Please refer to the precautions on manual notation for icons in the table.
)"Manual Symbols and Terminology"
32
Device Bit Address Word Address Notes
bits
*3
Counter (Count Up Flag) C0000 - C4095 -
Task Flag *3
TKB000 - TKB127 -
(Bit)
Task Flag *3
TK000.00 - TK127.07 TK000 - TK126
(Status)
*5
Data Register - DR00 - DR15
*1 Do not write in Channel I/O address 1500-1899 and Data Memory address D30000-D31599 from the Display.
Because those address are used for setting the system on the External Device.
*2 Write disable in A000 - A447 and A10000 - A11535.
*3 Write disable
*4 Max 24 bank (E0 to E18) can be used. 1 bank is 32768 words. Available bank number is different depending
on the CPU unit.
*5 Write disable during RUN
• Please refer to the GP-Pro EX Reference Manual for system data area.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
• Please refer to the precautions on manual notation for icons in the table.
)"Manual Symbols and Terminology"
32bit
Device Bit Address Word Address Notes
s
Timer *2
T0000-T4095 -
(Time Up Flag)
Counter *2
C0000-C4095 -
(Count Up Flag)
Task Flag *2
TKB00-TKB31 -
(Bit)
Task Flag *2
TK00.00-TK31.07 TK00-TK30
(Status)
• Please refer to the GP-Pro EX Reference Manual for system data area.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
• Please refer to the precautions on manual notation for icons in the table.
)"Manual Symbols and Terminology"
32bit
Device Bit Address Word Address Notes
s
Timer *2
T000-T255 -
(Time Up Flag)
Counter *2
C000-C255 -
(Count Up Flag)
• Please refer to the GP-Pro EX Reference Manual for system data area.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
• Please refer to the precautions on manual notation for icons in the table.
)"Manual Symbols and Terminology"
32bit
Device Bit Address Word Address Notes
s
Timer *2
T000-T255 -
(Time Up Flag)
Counter *2
C000-C255 -
(Count Up Flag)
• Please refer to the GP-Pro EX Reference Manual for system data area.
Cf. GP-Pro EX Reference Manual "LS Area (Direct Access Method Area)"
• Please refer to the precautions on manual notation for icons in the table.
)"Manual Symbols and Terminology"
Use device code and address code when you select "Device & Address" for the address type in data displays.
Task Flag
TK 0002 Word Address
(Status)
8 Error Messages
Error messages are displayed on the screen of Display as follows: "No. : Device Name: Error Message (Error
Occurrence Area)". Each description is shown below.
Item Description
No. Error No.
Name of External Device where error occurs. Name of External Device is a title of
Device Name
External Device set with GP-Pro EX. (Initial value [PLC1])
Error Message Displays messages related to the error which occurs.
Displays IP address or device address of External Device where error occurs, or error codes
received from External Device.
• Device specific error codes (2 bytes) are structured as "Main Response Code (1 byte)" and "Sub
Response Code (1 bytes)". If the Main Response Code is 0x11 and the Sub Response Code is 0x03,
then the received error code is 0x1103.
• Refer to your External Device manual for details on received error codes.
• Refer to "Display-related errors" in "Maintenance/Troubleshooting Guide" for details on the error
messages common to the driver.