Professional Documents
Culture Documents
150
SOURCE_DC_1 SUPPLY_1
0.16A LOAD_1
0.14A 0.9V, 1.76A 0.2A
10V - 14V 10AX066_VCC
10.0A m ax
TPS563200 LOAD_9
1.56A
10AX066_VCCP
SUPPLY_2
LOAD_10
0.01A 1.8V, 0.08A 0.01A
10AX066_VCCPT
® TPS62171
LOAD_4
0.01A
10AX066_VCCIO#3
LOAD_5
0.01A
10AX066_VCCIO#4
LOAD_7
10AX066_VCCIO#5
LOAD_8
0.01A
Created : 2017-05-11 12:53:46.150 10AX066_VCCIO#7
Project Summary
1. Total System Efficiency 76.712 %
2. Total System BOM Count 15.0
3. Total System Footprint 148.0 mm2
4. Total System BOM Cost $2.79
5. Total System Power Dissipation 512.1 mW
--> Launch WEBENCH Power Architect.
My Comments
No comments
Power Supplies
# Name NSID Description Vout Iout Efficiency Foot- Cost Design Page
print
1. SUPPLY_1 TPS563200 Switcher : 17V, 3A,6-pin, Low Iq 0.9 V 1.761 A 79.9% 74 $1.68 910 4
Synchronous buck converter with
Advanced Eco-mode
2. SUPPLY_2 TPS62171 Switcher : 1.8 V 0.08 A 70.8% 62 $0.95 912 13
3V-17V,1.8Vout,0.5A,Buck
Converter with Power Good
3. SUPPLY_3 LP5910-1.2 LDO : Ultra Low-Noise, 300-mA 1.2 V 0.07 A 60.5% 12 $0.16 911 9
Linear Regulator for RF/Analog
Circuits
Power Loads
# Name VLoad ILoad Description
1. 10AX066_VCC 0.9 V 0.2 A VoutRipple=5%
2. 10AX066_VCCP 0.9 V 1.561 A VoutRipple=10%
3. 10AX066_VCCIO#1 1.2 V 0.01 A VoutRipple=10%
4. 10AX066_VCCIO#2 1.2 V 0.01 A VoutRipple=10%
5. 10AX066_VCCIO#3 1.2 V 0.01 A VoutRipple=10%
6. 10AX066_VCCIO#4 1.2 V 0.01 A VoutRipple=10%
7. 10AX066_VCCIO#5 1.2 V 0.01 A VoutRipple=10%
8. 10AX066_VCCIO#6 1.2 V 0.01 A VoutRipple=10%
9. 10AX066_VCCIO#7 1.2 V 0.01 A VoutRipple=10%
10. 10AX066_VCCPT 1.8 V 0.01 A VoutRipple=10%
FPGAs, Processors
# Manufacturer Part Number Name Series Description
1. Altera 10AX066 FPGA_1 Arria 10 GX FPGA Altera Arria 10 GX 10AX066
http://www.altera.com/literature/hb/arria-10/a10_datasheet.pdf
WEBENCH Project Report Project : 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Project Diagram
WEBENCH® Power Architect Project ID : 113 PA_Project_304 (m odified from 301) FPGA Architect 2017- 05- 11 12:53:46.150
SOURCE_DC_1 SUPPLY_1
0.16A LOAD_1
0.14A 0.9V, 1.76A 0.2A
10V - 14V 10AX066_VCC
10.0A m ax
TPS563200 LOAD_9
1.56A
10AX066_VCCP
SUPPLY_2
TPS62171 SUPPLY_3
LOAD_2
0.07A 1.2V, 0.07A 0.01A
10AX066_VCCIO#1
0.01A LOAD_4
10AX066_VCCIO#3
0.01A LOAD_5
10AX066_VCCIO#4
0.01A LOAD_6
10AX066_VCCIO#5
0.01A LOAD_7
10AX066_VCCIO#6
0.01A LOAD_8
10AX066_VCCIO#7
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
L1
1.5 μH
14.4 m Ohm
TPS5 6 3 2 0 0 DDC
VIN SW Cbst
100.0 nF
280.0 m Ohm
EN U1 VBST _Vout_1
Cin
22.0 μF Cout
2.0 m Ohm 68.0 μF
Rfbb 3.494 m Ohm
10.0 kOhm
63.0 m W
_GND_1
_Vout_2
Iout_2
Electrical BOM
# Name Manufacturer Part Number Properties Qty Price Footprint
VDC= 25.0 V
IRMS= 0.0 A
2. Cin MuRata GRM32ER61E226KE15L Cap= 22.0 uF 1 $0.17
Series= X5R ESR= 2.0 mOhm 1210 15 mm
2
VDC= 25.0 V
IRMS= 3.67 A
3. Cout TDK C3216X6S0G686M160AC Cap= 68.0 uF 1 $0.37
Series= X6S ESR= 3.494 mOhm 1206_190 11 mm
2
VDC= 4.0 V
IRMS= 3.8813 A
4. L1 Coilcraft XFL4020-152MEB L= 1.5 μH 1 $0.61
DCR= 14.4 mOhm
2
XFL4020 25 mm
5. Rfbb Vishay-Dale CRCW040210K0FKED Res= 10.0 kOhm 1 $0.01
Series= CRCW..e3 Power= 63.0 mW 0402 3 mm
2
Tolerance= 1.0%
6. Rfbt Vishay-Dale CRCW04021K87FKED Res= 1.87 kOhm 1 $0.01
Series= CRCW..e3 Power= 63.0 mW 0402 3 mm
2
Tolerance= 1.0%
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
L Ipp Vout p- p
0 .9 0 0 0 .0 1 0 0
0 .8 9 5 0 .0 0 9 5
0 .8 9 0 0 .0 0 9 0
0 .8 8 5 0 .0 0 8 5
0 .8 8 0
0 .0 0 8 0
0 .8 7 5
0 .0 0 7 5
Vout p- p(V)
0 .8 7 0
L Ipp(A)
0 .0 0 7 0
0 .8 6 5
0 .8 6 0 0 .0 0 6 5
0 .8 5 5 0 .0 0 6 0
0 .8 5 0 0 .0 0 5 5
0 .8 4 5 0 .0 0 5 0
0 .8 4 0
0 .0 0 4 5
0 .8 3 5
0 .0 0 4 0
0 .8 3 0
0 .0 0 3 5
0 .8 2 5
0 .8 2 0 0 .0 0 3 0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
6 .5
6 .0 0 .9 0 2 1 2 0 0 0 1
5 .5
5 .0 0 .9 0 2 1 2 0 0 0 0
4 .5
4 .0 0 .9 0 2 1 1 9 9 9 9
3 .5
3 .0 0 .9 0 2 1 1 9 9 9 8
2 .5
2 .0 0 .9 0 2 1 1 9 9 9 7
1 .5
1 .0 0 .9 0 2 1 1 9 9 9 6
0 .5
0 .0 0 .9 0 2 1 1 9 9 9 5
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 0 .2 5 0 .5 0 0 .7 5 1 .0 0 1 .2 5 1 .5 0 1 .7 5
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Efficiency IC Tj
85 5 2 .5
80
5 0 .0
75
4 7 .5
70
65 4 5 .0
Efficiency(%)
IC Tj(degC)
60
4 2 .5
55
4 0 .0
50
45 3 7 .5
40
3 5 .0
35
30 3 2 .5
25 3 0 .0
20
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Cin IRMS(A)
0 .3 5
Cin Pd(W)
0 .0 0 0 3 5
0 .3 0
0 .0 0 0 3 0
0 .2 5
0 .0 0 0 2 5
0 .2 0
0 .0 0 0 2 0
0 .0 0 0 1 5 0 .1 5
0 .0 0 0 1 0 0 .1 0
0 .0 0 0 0 5 0 .0 5
0 .0 0 0 0 0 0 .0 0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
0 .1 2 1 .0
Pout(W)
0 .1 1 0 .9
0 .1 0 0 .8
0 .0 9
0 .7
0 .0 8
0 .0 7 0 .6
0 .0 6 0 .5
0 .0 5 0 .4
0 .0 4
0 .3
0 .0 3
0 .2
0 .0 2
0 .0 1 0 .1
0 .0 0 0 .0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Cout Pd(W)
0 .1 7 5 0 .0 0 0 1 7 5
0 .1 5 0 0 .0 0 0 1 5 0
0 .1 2 5 0 .0 0 0 1 2 5
0 .1 0 0 0 .0 0 0 1 0 0
0 .0 7 5 0 .0 0 0 0 7 5
0 .0 5 0 0 .0 0 0 0 5 0
0 .0 2 5 0 .0 0 0 0 2 5
0 .0 0 0 0 .0 0 0 0 0 0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Total Pd IC Iq Pd
0 .0 0 2 4 5
0 .4 0 0
0 .0 0 2 4 0
0 .3 7 5
0 .0 0 2 3 5
0 .3 5 0
0 .0 0 2 3 0
0 .3 2 5
0 .0 0 2 2 5
0 .3 0 0
0 .0 0 2 2 0
0 .2 7 5
0 .0 0 2 1 5
Total Pd(W)
IC Iq Pd(W)
0 .2 5 0
0 .0 0 2 1 0
0 .2 2 5
0 .0 0 2 0 5
0 .2 0 0
0 .0 0 2 0 0
0 .1 7 5 0 .0 0 1 9 5
0 .1 5 0 0 .0 0 1 9 0
0 .1 2 5 0 .0 0 1 8 5
0 .1 0 0 0 .0 0 1 8 0
0 .0 7 5 0 .0 0 1 7 5
0 .0 5 0 0 .0 0 1 7 0
0 .0 2 5 0 .0 0 1 6 5
0 .0 0 0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
IC Pd L Pd
0 .0 4 7 5
0 .3 5 0 0 .0 4 5 0
0 .3 2 5 0 .0 4 2 5
0 .0 4 0 0
0 .3 0 0
0 .0 3 7 5
0 .2 7 5 0 .0 3 5 0
0 .2 5 0 0 .0 3 2 5
0 .2 2 5 0 .0 3 0 0
IC Pd(W)
L Pd(W)
0 .0 2 7 5
0 .2 0 0
0 .0 2 5 0
0 .1 7 5 0 .0 2 2 5
0 .1 5 0 0 .0 2 0 0
0 .0 1 7 5
0 .1 2 5
0 .0 1 5 0
0 .1 0 0 0 .0 1 2 5
0 .0 7 5 0 .0 1 0 0
0 .0 0 7 5
0 .0 5 0
0 .0 0 5 0
0 .0 2 5 0 .0 0 2 5
0 .0 0 0 0 .0 0 0 0
0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8 0 .0 0 .1 0 .2 0 .3 0 .4 0 .5 0 .6 0 .7 0 .8 0 .9 1 .0 1 .1 1 .2 1 .3 1 .4 1 .5 1 .6 1 .7 1 .8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
55
50
45
40
35
30
25
20
15
10
5
0
1 E- 4 1 E- 3 1 E- 2 1 E- 1 1 E0
Iout(A)
1 0 .0 1 2 .0 1 4 .0
Operating Values
# Name Value Category Description
1. Cin IRMS 452.862 mA Current Input capacitor RMS ripple current
2. Cout IRMS 259.557 mA Current Output capacitor RMS ripple current
3. Iin Avg 141.63 mA Current Average input current
4. L Ipp 899.13 mA Current Peak-to-peak inductor ripple current
5. BOM Count 7 General Total Design BOM count
6. FootPrint 74.0 mm
2
General Total Foot Print Area of BOM components
7. Frequency 669.01 kHz General Switching frequency
8. Mode CCM General Conduction Mode
9. Pout 1.585 W General Total output power
10. Total BOM $1.68 General Total BOM Cost
11. Vout Actual 902.12 mV Op_Point Vout Actual calculated based on selected voltage divider resistors
12. Vout OP 900.0 mV Op_Point Operational Output Voltage
13. Duty Cycle 6.945 % Op_point Duty cycle
14. Efficiency 79.932 % Op_point Steady state efficiency
15. IC Tj 52.113 degC Op_point IC junction temperature
16. ICThetaJA 62.9 degC/W Op_point IC junction-to-ambient thermal resistance
17. IOUT_OP 1.761 A Op_point Iout operating point
18. VIN_OP 14.0 V Op_point Vin operating point
19. Vout p-p 4.238 mV Op_point Peak-to-peak output ripple voltage
20. Cin Pd 410.168 μW Power Input capacitor power dissipation
21. Cout Pd 235.391 μW Power Output capacitor power dissipation
22. IC Iq Pd 2.417 mW Power IC Iq Pd
23. IC Pd 351.561 mW Power IC power dissipation
24. L Pd 45.626 mW Power Inductor power dissipation
25. Total Pd 397.912 mW Power Total Power Dissipation
26. Vout Tolerance 1.638 % Vout Tolerance based on IC Tolerance (no load) and voltage divider
resistors if applicable
Design Inputs
# Name Value Description
1. Iout 1.761 Maximum Output Current
2. VinMax 14.0 Maximum input voltage
3. VinMin 10.0 Minimum input voltage
4. Vout 900.0 m Output Voltage
5. base_pn TPS563200 Base Product Number
6. source DC Input Source Type
7. Ta 30.0 Ambient temperature
Design Assistance
1. TPS563200 Product Folder : http://www.ti.com/product/TPS563200 : contains the data sheet and other resources.
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
LP5 9 1 0 - 1 P2 YKA
IN OUT
U1
EN GND
_Vout_1
Vin
Cin Cout
1.0 μF 1.0 μF
6.065 m Ohm 6.065 m Ohm
Iout_1
_GND_1
Electrical BOM
# Name Manufacturer Part Number Properties Qty Price Footprint
VDC= 6.3 V
IRMS= 1.36934 A
2. Cout MuRata GRM188R60J105KA01D Cap= 1.0 uF 1 $0.01
Series= X5R ESR= 6.065 mOhm 0603 5 mm
2
VDC= 6.3 V
IRMS= 1.36934 A
3. U1 Texas Instruments LP5910-1.2YKAR Switcher 1 $0.14
2
YKA0004ACAC 3 mm
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
0 .0 6 5 73
72
0 .0 6 0
71
0 .0 5 5
70
0 .0 5 0 69
Efficiency(%)
Iin Avg(A)
0 .0 4 5 68
0 .0 4 0 67
0 .0 3 5 66
65
0 .0 3 0
64
0 .0 2 5
63
0 .0 2 0
62
0 .0 1 5 61
0 .0 1 0 60
0 .0 0 5 59
58
0 .0 0 0
0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7
Output Current (A) Output Current (A)
Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V
IC Pd Total Pd
0 .0 5 5 0 .0 5 5
0 .0 5 0 0 .0 5 0
0 .0 4 5 0 .0 4 5
0 .0 4 0 0 .0 4 0
Total Pd(W)
0 .0 3 5 0 .0 3 5
IC Pd(W)
0 .0 3 0 0 .0 3 0
0 .0 2 5 0 .0 2 5
0 .0 2 0 0 .0 2 0
0 .0 1 5 0 .0 1 5
0 .0 1 0 0 .0 1 0
0 .0 0 5 0 .0 0 5
0 .0 0 0 0 .0 0 0
0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7
Output Current (A) Output Current (A)
Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V
Pout IC Tj
0 .0 8 5
41
0 .0 8 0
0 .0 7 5 40
0 .0 7 0 39
0 .0 6 5
38
0 .0 6 0
IC Tj(degC)
0 .0 5 5 37
Pout(W)
0 .0 5 0
36
0 .0 4 5
0 .0 4 0 35
0 .0 3 5 34
0 .0 3 0
33
0 .0 2 5
0 .0 2 0 32
0 .0 1 5
31
0 .0 1 0
0 .0 0 5 30
0 .0 0 0
0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7
Output Current (A) Output Current (A)
Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Output Current(A)
0 .2 2 5
IC Iground(A)
0 .0 0 0 1 0 2 5
0 .2 0 0
0 .0 0 0 1 0 0 0
0 .1 7 5
0 .0 0 0 0 9 7 5 0 .1 5 0
0 .0 0 0 0 9 5 0 0 .1 2 5
0 .0 0 0 0 9 2 5 0 .1 0 0
0 .0 0 0 0 9 0 0 0 .0 7 5
0 .0 0 0 0 8 7 5 0 .0 5 0
0 .0 0 0 0 8 5 0 0 .0 2 5
0 .0 0 0
0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 1 .2 5 1 .5 0 1 .7 5 2 .0 0 2 .2 5 2 .5 0 2 .7 5 3 .0 0 3 .2 5
Output Current (A) Input Voltage
Vin= 1 .6 2 V Vin= 1 .8 V Vin= 1 .9 8 V Safe Operating Area Operating Point
PSRR vs Frequency
85
80
75
70
PSRR((dB))
65
60
55
50
45
40
35
30
100 1 0 ,0 0 0 1 ,0 0 0 ,0 0 0
Frequency
1
Operating Values
# Name Value Category Description
1. IC Iground 111.25 μA Current IC ground current
2. Iin Avg 70.111 mA Current Average input current
3. BOM Count 3 General Total Design BOM count
4. FootPrint 12.0 mm
2
General Total Foot Print Area of BOM components
5. IC Tolerance 24.0 mV General IC Feedback Tolerance
6. Output Noise RMS 12.0 μV General Noise RMS
7. Pout 84.0 mW General Total output power
8. Total BOM $0.16 General Total BOM Cost
9. Vin p-p 2.399 mV Op_Point Input Source ripple voltage
10. Vout OP 0.0 V Op_Point Operational Output Voltage
11. Efficiency 60.51 % Op_point Steady state efficiency
12. IC Tj 41.118 degC Op_point IC junction temperature
13. ICThetaJA 202.8 degC/W Op_point IC junction-to-ambient thermal resistance
14. IOUT_OP 70.0 mA Op_point Iout operating point
15. Input Ripple Frequency 867.1 kHz Op_point Input Source Ripple Frequency for PSRR Calculation
16. PSRR est. -34.474 dB Op_point Power Supply Rejection Ratio estimated
17. VIN_OP 1.98 V Op_point Vin operating point
18. Vout p-p 45.321 μV Op_point Peak-to-peak output ripple voltage
19. IC Pd 54.82 mW Power IC power dissipation
20. Total Pd 54.82 mW Power Total Power Dissipation
21. Vout Tolerance 2.0 % Vout Tolerance based on IC Tolerance (no load) and voltage divider
resistors if applicable
Design Inputs
# Name Value Description
1. Iout 70.0 m Maximum Output Current
2. VinMax 1.98 Maximum input voltage
3. VinMin 1.62 Minimum input voltage
4. Vout 1.2 Output Voltage
5. base_pn LP5910-1.2 Base Product Number
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Design Assistance
1.
2. LP5910-1.2 Product Folder : http://www.ti.com/product/LP5910 : contains the data sheet and other resources.
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
L1
2.2 μH
TPS6 2 1 7 1 47.0 m Ohm
VIN SW
EN VOS _Vout_1
Rpg
100.0 kOhm
63.0 m W
Vin U1
AGND PG
PGND FB
Cin
10.0 μF Cout Iout_1
2.553 m Ohm 22.0 μF
3.593 m Ohm
ETPAD
_GND_1
_Vout_2
Iout_2
Electrical BOM
# Name Manufacturer Part Number Properties Qty Price Footprint
VDC= 25.0 V
IRMS= 0.0 A
2. Cout MuRata GRM31CR70J226KE19L Cap= 22.0 uF 1 $0.12
Series= X7R ESR= 3.593 mOhm 1206_190 11 mm
2
VDC= 6.3 V
IRMS= 3.44359 A
3. L1 Bourns SDR0403-2R2ML L= 2.2 μH 1 $0.18
DCR= 47.0 mOhm
2
SDR0403 28 mm
4. Rpg Vishay-Dale CRCW0402100KFKED Res= 100.0 kOhm 1 $0.01
Series= CRCW..e3 Power= 63.0 mW 0402 3 mm
2
Tolerance= 1.0%
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
L Ipp Vout p- p
0 .3 6 5 0 .0 0 2 4 0 0 0
0 .0 0 2 3 9 7 5
0 .3 6 0
0 .0 0 2 3 9 5 0
0 .3 5 5 0 .0 0 2 3 9 2 5
0 .0 0 2 3 9 0 0
0 .3 5 0
0 .0 0 2 3 8 7 5
0 .0 0 2 3 8 5 0
Vout p- p(V)
0 .3 4 5
0 .0 0 2 3 8 2 5
L Ipp(A)
0 .3 4 0 0 .0 0 2 3 8 0 0
0 .0 0 2 3 7 7 5
0 .3 3 5
0 .0 0 2 3 7 5 0
0 .3 3 0 0 .0 0 2 3 7 2 5
0 .0 0 2 3 7 0 0
0 .3 2 5 0 .0 0 2 3 6 7 5
0 .0 0 2 3 6 5 0
0 .3 2 0
0 .0 0 2 3 6 2 5
0 .3 1 5 0 .0 0 2 3 6 0 0
0 .0 0 2 3 5 7 5
0 .3 1 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Efficiency(%)
6 .0
5 .5 6 7 .5
5 .0
4 .5 6 5 .0
4 .0
3 .5
6 2 .5
3 .0
2 .5
6 0 .0
2 .0
1 .5
1 .0 5 7 .5
0 .5
0 .0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
IC Tj Cin Pd
3 3 .7 5
0 .0 0 0 0 1 8
3 3 .5 0
0 .0 0 0 0 1 7
3 3 .2 5
0 .0 0 0 0 1 6
3 3 .0 0 0 .0 0 0 0 1 5
3 2 .7 5 0 .0 0 0 0 1 4
3 2 .5 0 0 .0 0 0 0 1 3
0 .0 0 0 0 1 2
IC Tj(degC)
3 2 .2 5
Cin Pd(W)
0 .0 0 0 0 1 1
3 2 .0 0
0 .0 0 0 0 1 0
3 1 .7 5
0 .0 0 0 0 0 9
3 1 .5 0 0 .0 0 0 0 0 8
3 1 .2 5 0 .0 0 0 0 0 7
3 1 .0 0 0 .0 0 0 0 0 6
3 0 .7 5 0 .0 0 0 0 0 5
0 .0 0 0 0 0 4
3 0 .5 0
0 .0 0 0 0 0 3
3 0 .2 5
0 .0 0 0 0 0 2
3 0 .0 0
0 .0 0 0 0 0 1
2 9 .7 5 0 .0 0 0 0 0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
0 .0 5 5
Iin Avg(A)
0 .0 1 2
0 .0 5 0 0 .0 1 1
0 .0 4 5 0 .0 1 0
0 .0 4 0 0 .0 0 9
0 .0 3 5 0 .0 0 8
0 .0 3 0 0 .0 0 7
0 .0 2 5 0 .0 0 6
0 .0 0 5
0 .0 2 0
0 .0 0 4
0 .0 1 5
0 .0 0 3
0 .0 1 0 0 .0 0 2
0 .0 0 5 0 .0 0 1
0 .0 0 0 0 .0 0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Pout IC Ipk
0 .1 5 0 .3 6 5
0 .1 4
0 .3 6 0
0 .1 3
0 .3 5 5
0 .1 2
0 .1 1 0 .3 5 0
0 .1 0
0 .3 4 5
IC Ipk(A)
0 .0 9
Pout(W)
0 .3 4 0
0 .0 8
0 .0 7 0 .3 3 5
0 .0 6
0 .3 3 0
0 .0 5
0 .3 2 5
0 .0 4
0 .0 3 0 .3 2 0
0 .0 2
0 .3 1 5
0 .0 1
0 .3 1 0
0 .0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
0 .0 6 0
Cout IRMS(A)
0 .0 0 0 0 1 7 5
Cout Pd(W)
0 .0 5 5
0 .0 5 0 0 .0 0 0 0 1 5 0
0 .0 4 5
0 .0 4 0 0 .0 0 0 0 1 2 5
0 .0 3 5
0 .0 0 0 0 1 0 0
0 .0 3 0
0 .0 2 5 0 .0 0 0 0 0 7 5
0 .0 2 0
0 .0 0 0 0 0 5 0
0 .0 1 5
0 .0 1 0
0 .0 0 0 0 0 2 5
0 .0 0 5
0 .0 0 0 0 .0 0 0 0 0 0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Total Pd IC Iq Pd
0 .0 3 0 0
0 .0 6 0
0 .0 2 7 5
0 .0 5 5
0 .0 2 5 0
0 .0 5 0
0 .0 2 2 5
0 .0 4 5
0 .0 2 0 0
0 .0 4 0
Total Pd(W)
IC Iq Pd(W)
0 .0 3 5 0 .0 1 7 5
0 .0 3 0 0 .0 1 5 0
0 .0 2 5 0 .0 1 2 5
0 .0 2 0 0 .0 1 0 0
0 .0 1 5 0 .0 0 7 5
0 .0 1 0 0 .0 0 5 0
0 .0 0 5 0 .0 0 2 5
0 .0 0 0 0 .0 0 0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
IC Pd L Pd
0 .0 6 0 0 .0 0 0 8 5
0 .0 0 0 8 0
0 .0 5 5
0 .0 0 0 7 5
0 .0 5 0 0 .0 0 0 7 0
0 .0 4 5 0 .0 0 0 6 5
0 .0 0 0 6 0
0 .0 4 0 0 .0 0 0 5 5
IC Pd(W)
L Pd(W)
0 .0 3 5 0 .0 0 0 5 0
0 .0 0 0 4 5
0 .0 3 0
0 .0 0 0 4 0
0 .0 2 5 0 .0 0 0 3 5
0 .0 0 0 3 0
0 .0 2 0
0 .0 0 0 2 5
0 .0 1 5 0 .0 0 0 2 0
0 .0 1 0 0 .0 0 0 1 5
0 .0 0 0 1 0
0 .0 0 5
0 .0 0 0 0 5
0 .0 0 0 0 .0 0 0 0 0
0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8 0 .0 0 0 .0 1 0 .0 2 0 .0 3 0 .0 4 0 .0 5 0 .0 6 0 .0 7 0 .0 8
Output Current (A) Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
7 5 .0
7 2 .5
7 0 .0
Efficiency(%)
6 7 .5
6 5 .0
6 2 .5
6 0 .0
5 7 .5
1 E- 3 3 .1 6 E- 3 1 E- 2 3 .1 6 E- 2
Output Current (A)
Vin= 1 0 .0 V Vin= 1 2 .0 V Vin= 1 4 .0 V
Operating Values
# Name Value Category Description
1. Cin IRMS 83.825 mA Current Input capacitor RMS ripple current
2. Cout IRMS 83.825 mA Current Output capacitor RMS ripple current
3. IC Ipk 362.182 mA Current Peak switch current in IC
4. Iin Avg 14.54 mA Current Average input current
5. L Ipp 362.18 mA Current Peak-to-peak inductor ripple current
6. BOM Count 5 General Total Design BOM count
7. FootPrint 62.0 mm
2
General Total Foot Print Area of BOM components
8. Frequency 867.1 kHz General Switching frequency
9. Mode DCM General Conduction Mode
10. Pout 144.198 mW General Total output power
11. Total BOM $0.95 General Total BOM Cost
12. Vout OP 1.8 V Op_Point Operational Output Voltage
13. Duty Cycle 5.699 % Op_point Duty cycle
14. Efficiency 70.837 % Op_point Steady state efficiency
15. IC Tj 33.615 degC Op_point IC junction temperature
16. ICThetaJA 61.8 degC/W Op_point IC junction-to-ambient thermal resistance
17. IOUT_OP 80.11 mA Op_point Iout operating point
18. VIN_OP 14.0 V Op_point Vin operating point
19. Vout p-p 2.399 mV Op_point Peak-to-peak output ripple voltage
20. Cin Pd 17.939 μW Power Input capacitor power dissipation
21. Cout Pd 25.247 μW Power Output capacitor power dissipation
22. IC Iq Pd 28.886 mW Power IC Iq Pd
23. IC Pd 58.496 mW Power IC power dissipation
24. L Pd 825.536 μW Power Inductor power dissipation
25. Total Pd 59.364 mW Power Total Power Dissipation
Design Inputs
# Name Value Description
1. Iout 80.11 m Maximum Output Current
2. VinMax 14.0 Maximum input voltage
3. VinMin 10.0 Minimum input voltage
4. Vout 1.8 Output Voltage
5. base_pn TPS62171 Base Product Number
6. source DC Input Source Type
7. Ta 30.0 Ambient temperature
Design Assistance
1. Feature Highlights: DCS-Control(TM) Architecture with upto 0.5A output current, 3V to 17V Input Voltage Range, 1.8V Fixed Output voltage,
Seamless Power Save Mode for Light Load Efficiency, Power Good Output, 100% Duty Cycle mode, Short Circuit Protection, Thermal
Shutdown
2. TPS62171 Product Folder : http://www.ti.com/product/TPS62171 : contains the data sheet and other resources.
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00
®
WEBENCH Power Architect Project
Texas Instruments' WEBENCH simulation tools attempt to recreate the performance of a substantially equivalent physical implementation
of the design. Simulations are created using Texas Instruments' published specifications as well as the published specifications of other
device manufacturers. While Texas Instruments does update this information periodically, this information may not be current at the time the
simulation is built. Texas Instruments does not warrant the accuracy or completeness of the specifications or any information contained therein.
Texas Instruments does not warrant that any designs or recommended parts will meet the specifications you entered, will be suitable for your
application or fit for any particular purpose, or will operate as shown in the simulation in a physical implementation. Texas Instruments does not
warrant that the designs are production worthy.
You should completely validate and test your design implementation to confirm the system functionality for your application prior to
production.
Use of Texas Instruments' WEBENCH simulation tools is subject to Texas Instruments' Site Terms and Conditions of Use. Prototype boards
based on WEBENCH created designs are provided AS IS without warranty of any kind for evaluation and testing purposes and are subject to
the terms of the Evaluation License Agreement.
WEBENCH Project Report 113 : PA_Project_304 (modified from 301) May 11, 2017 12:54:02 GMT-07:00