Professional Documents
Culture Documents
Electric Horn
25500096 Rev A5 1221
Limited Warranty: This product’s limited warranty can • The nameplate should NOT be obscured, as it
be found at www.fedsig.com/SSG-Warranty. contains cautionary and/or other information of
importance to maintenance personnel.
Messages to Installers and Users This product
Failure to follow all safety precautions and
should be installed to code by a licensed electrician instructions may result in property damage, serious
and follow all safety instructions. Failure to do so may injury, or death.
result in property damage, serious injury, or death.
Unpacking the Device: After unpacking the device,
The selection of the mounting location for this horn, examine it for damage and verify the parts. If a part
its controls, and the routing of the wiring are to be is missing or appears damaged, do not attempt to
accomplished under the direction of the Facilities install. Contact Federal Signal Customer Support at
Engineer and the Safety Engineer. Listed below +1 708-587-3587 or iordersup@fedsig.com.
are some other important safety instructions and
SOUND RESTRICTION: Do not paint the horn. No
precautions you should follow:
finish or coating is required. Paint may obstruct the
• Read and understand all instructions before sound output, reducing the effectiveness of the horn.
installing, operating, or maintaining this Failure to heed this warning may cause serious injury
or death.
equipment.
• Do not connect this unit to the system when Overview: The Model 450E is a polarized, high-output,
power is on. continuous duty, indoor/outdoor-rated, electronic horn
suitable for use in fire alarm systems in public mode
• Optimum sound distribution will be severely applications. It is capable of reproducing coded blasts
reduced if any objects are in front of the horn. or sustained tones.
You should ensure that the front of the horn is
In addition to fire alarm system applications, the
clear of any obstructions.
Federal Signal 450E horn is excellent for general
• All effective warning horns produce loud alarm, start and dismissal, coded paging, and process
sounds, which may cause, in certain situations, control signaling in areas of high ambient noise levels.
permanent hearing loss. The device should be
Meets Type 4X and IP66 requirements when used with
installed far enough away from potential listeners separately purchased Model WB or WB-NM mounting
to limit their exposure while still maintaining accessories.
its effectiveness. The OSHA Code of Federal
Regulations 1910.95 Noise Standard provides Table 1 Specifications
guidelines for permissible noise exposure levels. Operating Voltage Fire Alarm Use: Regulated 24 Vdc
(16-33 Vdc)
• After installation, ensure that all mounting
General Signaling Use: 12-24 Vdc
screws are tightened.
Current 0.25 A
• Establish a procedure to routinely check Inrush Current 764 mARMS over a 16.7 ms time
the signal system for proper activation and window
operation. Audibility Rating 89 dB per UL Reverberation Room.
• Any maintenance to the unit MUST be performed 98 dBA per ULC Anechoic Chamber.
For directional characteristics, refer
by a trained electrician in accordance with NEC
to Figure 1.
Guidelines and local codes.
• Never alter the unit in any manner.
Figure 1 Dispersion characteristics for Mounting the Horn
audible signal devices There is no specific mounting orientation required for
3m AUDIBLE SIGNAL DEVICE 3m the horn. For the required spacing between horns, refer
85 dB 85 dB
to the local fire alarm code. There are three mounting
options: non-weatherproof mounting, weatherproof
14º
27º mounting, and weatherproof panel mounting.
-6 dB -6 dB
Non-Weatherproof Mounting
–3 dB –3 dB
If weatherproof mounting is not required, mount the
99 dB
horn on a 4" x 4" outlet box with the two supplied
#8-32 x 1-5/8" screws. Torque the mounting screws to
a maximum of 16 in-lb (1.8 Nm). See Figure 3.
Wiring the Horn
SHOCK HAZARD: To avoid electrical shock hazards,
Figure 3 Non-weatherproof mounting
do not connect wires when power is applied. Failure
to heed this warning may cause serious injury or #8-32 KEPS NUT (2)
death.
PANEL
AGUJERO DE CONTOURS DE
3-3/8"
PASO PARA DÉCOUPE POUR
(85.7 mm) DISPOSITIF
DISPOSITIVO
TYP./TIP
1/2"
1-11/16" OUTLINE OF
(12.7 mm)
(42.9 mm) CLEARANCE
TYP./TIP
TYP./TIP HOLE FOR
DEVICE
98 dBA según la norma de cámara para usar en sistemas supervisados. Consulte los
anecoica de ULC. códigos locales de alarmas contra incendios si es
Para los características necesario un dispositivo de final de línea.
direccionales, consulte la Figura 1.
Figura 1 Características de dispersión para Montaje de la bocina
dispositivos con señal sonora No hay una orientación específica de montaje
85 dB
3m DISPOSITIVO CON SEÑAL SONORA 3m
85 dB
requerida para la bocina. Para conocer el espacio
requerido entre las bocinas, consulte el código local
14º
de alarmas contra incendios. Hay tres opciones
27º
de montaje: Montaje resistente a la intemperie,
-6 dB -6 dB
montaje resistente a la intemperie y montaje en panel
resistente a la intemperie.
–3 dB –3 dB
Montaje no impermeable
99 dB
Mantenimiento y servicio
Asistencia técnica: póngase en contacto con nuestro
equipo de Soporte Técnico al
+1 708-587-3587 o escriba a
signalsupport@fedsig.com.
PANEL
290A7663
AGUJERO DE CONTOURS DE
3-3/8"
PASO PARA DÉCOUPE POUR
(85.7 mm) DISPOSITIF
DISPOSITIVO
TYP./TIP
1/2"
1-11/16" OUTLINE OF
(12.7 mm)
(42.9 mm) CLEARANCE
TYP./TIP
TYP./TIP HOLE FOR
DEVICE
- DE L'UNITÉ DE CONTRÔLE
-
Tableau 1 Caractéristiques techniques
Tension de Utilisation d’une alarme incendie
fonctionnement (16-33 Vcc)
Utilisation de signalisation générale
+
(12-24 Vcc)
Intensité 0,25 A -
Courant d’appel Valeur efficace de 764 mA sur une
période de 16,7 ms REMARQUE : Cet appareil est polarisé par une 290A7655
Maintenance et entretien
Assistance technique : Contactez notre équipe
d’assistance technique au +1 708-587-3587 ou à
l’adresse signalsupport@fedsig.com.
Un joint en caoutchouc plat est fourni pour les Retours de produits : Les retours requièrent
installations d’avertisseur sonore qui nécessitent un l’autorisation de Federal Signal. Contactez votre
joint étanche à l’eau lors du montage sur panneau. distributeur agréé pour obtenir plus d’informations
Voir la figure 5. concernant notre politique de retour ou pour demander
le retour d’un produit.
Figure 5 Montage avec panneau à l’épreuve
des intempéries
ÉCROUS
KEPS 8-32
JOINT
PANNEAU
290A7658
AGUJERO DE CONTOURS DE
3-3/8"
PASO PARA DÉCOUPE POUR
(85.7 mm) DISPOSITIF
DISPOSITIVO
TYP./TIP
1/2"
1-11/16" OUTLINE OF
(12.7 mm)
(42.9 mm) CLEARANCE
TYP./TIP
TYP./TIP HOLE FOR
DEVICE