Professional Documents
Culture Documents
installation conditions. “Bolt size is hole size” – the drill bit Machine Lathed
Expansion Cone
diameter needed for proper installation is the same as the
anchor diameter.
Key Features & Benefits USA ENGINEERED
Drill the hole deeper than the intended embedment, but not closer than
two diameters to the opposite surface of the concrete.
2. A clean hole is necessary for proper performance. Clean the hole using a 1 2
nylon brush and compressed air.
3. Assemble the nut and washer onto the anchor. Drive the anchor through
the material to be fastened at the calculated embedment depth.
4. Tighten the nut, or head, 3 to 5 turns past the hand tight position.
Installing with a torque wrench is recommended for optimum
performance. Refer to Recommended Setting Torque* in the table below.
NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide-tipped drill
bits meeting ANSI B212.15 diameter standards.
3 4
Installation Data
Recommended Setting Torque (ft-lbs)*
Anchor Drill Bit Fixture Clearance Thread Nut Washer Wrench
Dia. (in.) Dia. (in.) Hole (in.) Size (UNC) Height (in.) Diameter (in.) Size (in.) Zinc & Stainless W/O Inspection
Galvanized Steel Turns to Set
1/4 1/4 5/16 1/4-20 7/32 5/8 7/16 6-8 4-8 3-5
3/8 3/8 7/16 3/8-16 21/64 13/16 9/16 20-25 20-25 3-5
1/2 1/2 9/16 1/2-13 7/16 1-1/16 3/4 50-55 40-50 3-5
5/8 5/8 11/16 5/8-11 35/64 1-3/4 15/16 90-95 80-90 3-5
3/4 3/4 13/16 3/4 -10 41/64 2 1-1/8 165-175 145-155 3-5
7/8 7/8 15/16 7/8-9 3/4 2-1/4 1-5/16 240-250 220-230 3-5
1 1 1-1/8 1-8 55/64 2-1/2 1-1/2 290-300 255-280 3-5
1-1/4 1-1/4 1-3/8 11/4-7 1-1/16 3 1-7/8 400-410 390-400 3-5
*Installation torque is listed for anchors installed in normal weight concrete
Min. 2"
Max. 3"
Anchor
(TYP)
Hot-Dip Galvanized Steel with Type 304 SS Clip Hot-Dip Galvanized Steel with Type 304 SS Clip
Anchor Min. Thread Anchor Min. Thread
Quantity Quantity Quantity Quantity
Catalog No. Size Embed. Length Catalog No. Size Embed. Length
Box Carton Box Carton
(in.) (in.) (in.) (in.) (in.) (in.)
ATG1413 1/4 x 1-3/4 1-1/4 3/4 100 800 ATG3441 3/4 x 4-1/4 3-1/4 2 10 80
ATG1421 1/4 x 2-1/4 1-1/4 1-1/4 100 800 ATG3443 3/4 x 4-3/4 3-1/4 2-1/2 10 80
ATG1431 1/4 x 3-1/4 1-1/4 2-1/4 100 800 ATG3452 3/4 x 5-1/2 3-1/4 3-1/4 10 60
ATG3821 3/8 x 2-1/4 1-3/4 1 50 400 ATG3461 3/4 x 6-1/4 3-1/4 3-3/4 10 60
ATG3823 3/8 x 2-3/4 1-3/4 1-1/2 50 400 ATG3470 3/4 x 7 3-1/4 4-3/4 10 60
ATG3830 3/8 x 3 1-3/4 1-3/4 50 400 ATG3482 3/4 x 8-1/2 3-1/4 5 10 40
ATG3833 3/8 x 3-3/4 1-3/4 2-1/2 50 400 ATG3410 3/4 x 10 3-1/4 5 10 40
ATG3850 3/8 x 5 1-3/4 3-1/4 50 400 ATG3412 3/4 x 12 3-1/4 5 4 16
ATG3870 3/8 x 7 1-3/4 4-1/2 50 300 ATG7860 7/8 x 6 3-7/8 3-1/2 4 24
ATG1223 1/2 x 2-3/4 2-1/8 1-1/8 25 200 ATG7880 7/8 x 8 3-7/8 5 4 16
ATG1233 1/2 x 3-3/4 2-1/8 2-1/8 25 200 ATG7810 7/8 x 10 3-7/8 5 4 16
ATG1241 1/2 x 4-1/4 2-1/8 2-5/8 25 200 ATG1060 1x6 4 3 4 24
ATG1242* 1/2 x 4-1/2 2-1/8 2-5/8 25 200 ATG1090 1x9 4 5 4 16
ATG1252 1/2 x 5-1/2 2-1/8 3-3/4 25 150 ATG1012 1 x 12 4 5 4 16
ATG1270 1/2 x 7 2-1/8 4-1/2 25 150 ATG11490* 1-1/4 x 9 5-5/8 5 4 12
ATG1282 1/2 x 8-1/2 2-1/8 5 10 40 ATG11412* 1-1/4 x 12 5-5/8 5 4 12
ATG1210 1/2 x 10 2-1/8 5 10 40 *Special Order
ATG5832 5/8 x 3-1/2 2-5/8 1-1/2 10 80
ATG5841 5/8 x 4-1/4 2-5/8 2-3/8 10 80
ATG5842* 5/8 x 4-1/2 2-5/8 2-5/8 10 80
ATG5850 5/8 x 5 2-5/8 3-1/8 10 80
ATG5860 5/8 x 6 2-5/8 4 10 80
ATG5870 5/8 x 7 2-5/8 4-1/2 10 80
ATG5882 5/8 x 8-1/2 2-5/8 5 10 40
ATG5810 5/8 x 10 2-5/8 5 10 40
ATG5812 5/8 x 12 2-5/8 5 10 40
Phone: 203-857-2200
Fax: 203-857-2201 • E-mail: sales@wejit.com
www.toggler.com • www.wejit.com
Ankr-TITE™, TOGGLER logo and typeface, Wej-It® and High-Performance Anchors®
are trademarks of Mechanical Plastics Corp. ©2014 Mechanical Plastics Corp. Rev. 8/15