Professional Documents
Culture Documents
Wedge
Technical Recommendations
Essentially the thread build portion has a smooth
‘ski slope’ transition into a linear torque climb as the
connection makes up.
IDM Code GDL23355/2 / March 2020
TORQUE
Yield Torque
Safety Margin
Operating Torque
TURNS
RUNNING MANUAL
TenarisHydril
1
By design Wedge Series 400™, Wedge Series 500™
10. Wedge Series™ Make up Acceptance
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
W1 TURNS
Acceptable
2
Computer Graph Wedge Series
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
W2 TURNS
IDM Code GDL23355/2 / March 2020
Acceptable
The first graph of this type of thread build should be disassembled and
the connections checked. Thereafter all similar graphs can be accepted
if all visual indications of correct connection assembly are acceptable.
TORQUE
OPTIMUM TORQUE
MINIMUM TORQUE
RUNNING MANUAL
W3 TURNS
Acceptable
TenarisHydril
TORQUE
OPTIMUM TORQUE
Technical Recommendations
W4 TURNS
Acceptable
. Possible Causes
. application guidelines.
.
Pipe movement during spin in.
Excessive thread compound .
Stabilize pipe during make up.
Reduce spin in speed.
. application.
Pipe OD contact from external
. equipment.
Excessive spin in speed.
RUNNING MANUAL
TenarisHydril
4
Computer Graph Wedge Series
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
W5 TURNS
IDM Code GDL23355/2 / March 2020
Acceptable
. Possible Causes
. pipe OD.
.
Clogged tong dies.
.
Ensure tong is level.
.
Worn tong dies.
.
Clean pipe OD.
.
Incorrect dies or tong jaws. Check snub line.
.
Tong not level.
.
Snub line movement.
Wet or oil covered pipe OD.
RUNNING MANUAL
TenarisHydril
5
Computer Graph Wedge Series
10. Wedge Series™ Make up Acceptance
TORQUE
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
w6 TURNS
Unacceptable
. reoccurrence
. Possible Causes
.
Clean or replace tong dies.
.
Clogged tong dies. Ensure tong and back up is
.
Worn tong dies. level and dies contact pipe OD
.
Incorrect dies or tong jaws. evenly.
.
Tong not level.
.
Snub line movement.
Wet or oil covered pipe OD.
. Recommendations
Break out, clean and inspect
6
Computer Graph Wedge Series
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
w7 TURNS
IDM Code GDL23355/2 / March 2020
Unacceptable
. Possible Causes
. both connections for damage.
.
Galled threads. If no damage found re-apply
.
Damaged threads. thread compound then
.
Pipe movement during spin in.
. re-make up connection.
.
Incorrect thread compound.
Contaminated thread
Ensure thread compound
is correct type and is not
. compound.
. contaminated.
.
Contaminated connections.
Misalignment. .
Stabilize pipe during make up.
Ensure threads are completely
clean prior to applying thread
. compound.
RUNNING MANUAL
Remedy misalignment.
TenarisHydril
7
Computer Graph Wedge Series
10. Wedge Series™ Make up Acceptance
TORQUE
OPTIMUM TORQUE
MINIMUM TORQUE
Technical Recommendations
w8 TURNS
Unacceptable
.
Pipe movement during spin in.
. for damage.
.
Incorrect thread compound.
Contaminated thread
If no damage found re-apply
thread compound then
. compound.
Running compound not . re-make up connection.
If no damage found accept
. homogenised.
. further graphs of similar type.
.
Excessive thread compound.
Misalignment.
Ensure thread compound
is correct type and is not
. contaminated.
Reduce quantity of thread
RUNNING MANUAL
.
Stabilize pipe during make up.
Ensure threads are completely
clean prior to applying thread
. compound.
TenarisHydril
Remedy misalignment.
8
10. Wedge Series™ Make up Acceptance
Technical Recommendations
IDM Code GDL23355/2 / March 2020
RUNNING MANUAL
Tenaris has produced this manual for general information only. While every effort has been made to
ensure the accuracy of the information contained within this publication, Tenaris does not assume any
TenarisHydril
responsibility or liability for any loss, damage, injury resulting from the use of information and data
herein. Tenaris products and services are only subject to the Company’s standard terms and Conditions
or otherwise to the terms resulting from the respective contracts of sale, services or license, as the case
may be. The information in this publication is subject to change or modification without notice. For more
complete information please contact a Tenaris’s representative or visit our website at www.tenaris.com.
This manual supersedes Version 03 / March 2018. ©Tenaris 2020. All rights reserved.