Professional Documents
Culture Documents
In the year of 2006, CHINT ranked 15th in the list of top 100
Companies released by Forbes, which were appraised from
all private companies (both listed as public and not) in China.
CHINT was also nominated as National Well-known Trademark,
one of the most prestigious honors for outstanding enterp-
rises by China State Administration of Industry and Commerce.
C US LISTED
R
TUV
EU Netherland Germany Germany Sweden Finland Czech Indonesia Ukrain Russia South Africa USA Canada UK
Summary
NA1-1000 NA1-2000
200A to 1000A 400A to 2000A
.1.
Air Circuit Breaker
1. General
1.1 Application scope
NA1 series air circuit breaker is suitable for the circuit of AC 50Hz/60Hz with rated service voltage 400V, 690V and rated service current up to
6300A. It is mainly used to distribute electric energy and protect circuits and electric equipment against over-load, under-voltage, short-circuit
and single-phase earthing fault. With intelligentized and selective protection functions, the breaker can improve the reliability of power supply,
and avoid unnecessary power failure. The breaker is applicable for power stations, factories, mines (for 690V) and modern high-buildings, especially
for the distribution system of intelligentized building.
1.2 Standard: IEC/EN 60947-2.
2. Operation Conditions
2.1 Temperature Condition: -5℃~40℃; the average value within 24h shall not exceed +35℃(special situation excluded);
2.2 Altitude:≤2000m;
2.3 Pollution grade: Grade 3;
2.4 Air conditions:
At mounting site, relative humidity not exceed 50% at the max temperature of +40℃, higher relative humidity is allowable under lower temperature,
RH could be 90% at +20℃, special measures should be taken to occurrence of dews;
2.5 Note: Without the intelligent controller, the breaker functions as a switch-disconnector.
3. Structure
+ =
.4.
Fault-breaking indicator Enclosure Under-voltage release
reset button Making button page 50
Closing release
Breaking/making
Name plate page 51
indicator
Auxiliary contact
page 51
Motor-driven energy
storage mechanism
Structure for in and out Locking device page 51
Rotary handle page 52
.5.
Air Circuit Breaker
Type NA1-2000
Rated ultimate short circuit breaking capacity Icu=80kA 400V 50kA 690V
Rated service short circuit breaking capacity Ics=50kA 400V 40kA 690V
Rated short-time withstand current Icw=50kA 1s 400V 40kA 1s 690V
Rated current In (A) 400 630 800 1000 1250 1600 2000
Number of poles 3, 4
Rated voltage Ue (V) 400, 690
Rated insulation voltage Ui (V) 1000
Rated current of N-pole In (A) 50%In, 100%In
Fixed disconnection time (ms) 23~32
Intelligent Standard type (M)
controller Communication type (H)
Electric life 5000
Operation
Non-maintenance 10,000
performance Mechanical life
Maintenance 20,000
Connection pattern Horizontal, Vertical
Drawout 3P/4P 68/77 70/80 74/81
Weight (kg)
Fixed 3P/4P 42/51 43/52 45/53
Rated ultimate short circuit breaking capacity Icu=80kA 400V 65kA 690V
Rated service short circuit breaking capacity Ics=65kA 400V 65kA 690V
Rated short-time withstand current Icw=65kA 1s 400V 50kA 1s 690V
Rated current In (A) 2000 2500 3200 4000
Number of poles 3, 4 3
Rated voltage Ue (V) 400, 690
Rated insulation voltage Ui (V) 1000
Rated current of N-pole In (A) 50%In, 100%In
Fixed disconnection time (ms) 23~32
Intelligent Standard type (M)
controller Communication type (H)
.6.
Type NA1-3200, NA1-4000
Electric life 5000
Operation
Non-maintenance 10,000
performance Mechanical life
Maintenance 20,000
Connection pattern Horizontal, Vertical
Drawout 3P/4P 94.5/117 119
Weight (kg)
Fixed 3P/4P 52.5/65.5
Type NA1-6300
Rated ultimate short circuit breaking capacity Icu=120kA 400V 85kA 690V
Rated service short circuit breaking capacity Ics=100kA 400V 75kA 690V
Rated short-time withstand current Icw=100kA 1s 400V 75kA 1s 690V
rated current In (A) 4000 5000 6300
Number of poles 3, 4 3
Rated voltage Ue (V) 400, 690
Rated insulation voltage Ui (V) 1000
Rated current of N-pole In (A) 50%In, 100%In
Fixed disconnection time (ms) 23~32
Intelligent Standard type (M)
controller Communication type (H)
Electric life 2500
Operation
Non-maintenance 5000
performance Mechanical life
Maintenance 10,000
Connection pattern Horizontal, Vertical
Drawout 3P/4P 210/233 233
Weight (kg)
Fixed 3P/4P
.7.
Air Circuit Breaker
268
H
N 226
315
259
101.5
8×φ5
312
270
Installation panel
46.5
5
216 15 A 9
N 239
70 70 70 Installation hole on right side
12
n×φ13
200,400A 35
15
35 53
n×φ10.5
12
18
630,800,
1000A NA1-1000 L1 L In(A) A(mm) n(3P/4P) H(mm)
12
4-9×13
800、1000 50 6/8 10
L1
NA1-1000 Fixed-type
216 34 Boring dimension of doorcase
268
N 226
H
362
8×φ5
101.5
316
304
358
Installation panel
5
91.5
16
Disconnected
L1 45 position Installation hole on right side
105 158
L 65
A 323
N 27 Connected positing
70 70 70
12
200,400A n×φ13
35
NA1-1000 L1 L
12
15
35
3P 194 284
18
630 50 6/8 8
2-11.5×8.5
800、1000 50 6/8 10
L1(3P)
L1(4P)
.8.
NA1-2000 Drawout-type
45(Disconnected position)
448(4-pole)
a
353(3-pole)
a
360(4-pole)
Φ11
265(3-pole)
112
258
439
2-11×17
42.5
Φ14
92
37
70
23
55
10 97 175
187.5 175
421 33
292
465 Right &outer side of breaker
375(3-pole)
470(4-pole)
21.5
8-Φ13
60
N-pole 28
14
155
37.5
268
302
378
302
95 95 95
47 20
Horizontal
Right & outer
N-pole
side of breaker
115
172 In A a mm
11-Φ5
40
15.5 Installation panel
344 10
17
630
800~1600 15 28
32-Φ13
Opening hole on panel 2000 20 60
95 95 95
Vertical
NA1-2000 Fixed-type
8-Φ13
335
60
112
N-pole 28
42
258
55
17
95 95 95
60
50 150
Horizontal
21
290
359 11 11
13
181
340(3-pole)
435(4-pole)
4-Φ12
311.2
150
269
N-pole
115
300
40
17
Installation hole on
28.5
340(4-pole)
Right &outer side Installation hole on 32-Φ13 28
435(4-pole) 8-φ5 right side of breaker 2 60
of breaker
342.2 95 95 95
Installation panel
.9.
Air Circuit Breaker
NA1-3200 Drawout-type
45(Disconnected position)
528(4-pole)
a
413(3-pole) In A A(mm)
2000~2500 20
a
3200 30
16-Φ13
112
100
258
439
25
N-pole 50
42.5
92
37
100
70
23
10 97 175
50
217.5 115 125 125
491
352 Horizontal
536
435(3-pole)
550(4-pole)
21.5
155
Φ11
440(4-pole)
268
302
325(3-pole)
378
362 115
N-pole
47 20
2-11×17
40
Φ14
17
32-Φ13 40
55
Right&outer
202 side of breaker 100
175 11-Φ5 15.5
33 404 115 125 125
Installation panel
Right &outer side of breaker
Opening hole on panel Vertical
86
a
15
N-pole 40
335
112
72
258
55
40
50 150
21
290
Horizontal
389 11 11
13
211
400(3-pole)
515(4-pole)
4-Φ12
150
N-pole
311
269
115
40
362
15
32-Φ13 40
86
515(4-pole) Right &outer side Installation hole on
of breaker 8-φ5 right side of breaker 2 115 115 115
404
Installation panel
Vertical
Opening hole on panel
.10.
NA1-4000 Drawout-type (3-pole)
45(Disconnected position)
30 528
439
258
112
42.5
92
70
10 97 175 217.5
37
494 352
550
21.5
20
155
268
302
40
103
Φ11
378
362
440
47 20
2-11×17 12-Φ13 50
Φ14 140
Right&outer
202 side of breaker
11-Φ5 15.5 197.5 197.5
55
45(Disconnected position)
928(4-pole)
813(3-pole)
30
112
258
449
42.5
37
92
70
10 97 175
217.5
494 352
835(3-pole)
950(4-pole)
N-pole)
21.5
28-Φ15
135 155 210
20
155
268
302
Φ11
818(4-pole)
40
103
378
362
703(3-pole)
47 20
2-11×17
55
Φ14
Right & outer
182 247 247
side of breaker
202
55
11-Φ5 15.5
175 Installation panel
33 404
.11.
Air Circuit Breaker
NA1-6300(In=6300A) Drawout-type(3-pole)
45(Disconnected position)
30 928
258
449
112
42.5
37
92
70
10 97 175 217.5
352
494
950
21.5
180 260
20
155
Φ11
268
302
40
103
378
362
818
47 20
2-11×17 24-Φ15 80
Φ14 337 337
Right & outer
202 side of breaker
55
11-Φ5 15.5
175 404 Installation panel
33
Right & outer
side of breaker Opening hole on panel
.12.
6. Secondary circuit wiring
6.1 NA1-1000
▲
3 5 7 9 14 15 17 19 21 23 25 27 29 31 33 35 37 39 XT
FU
Intelligent Q F X M
controller
Power of control circuit
DF1 DF2 DF3
SA DF4
TA
FU
1 2 4 6 8 10 11 12 13 16 18 20 22 24 26 28 30 32 34 36 38 40 XT
DC24V
+Power-
module
.13.
Air Circuit Breaker
L1 FU
N
PE
Profibus-DP L N PE
Fault indicator 1 2 3 4 5 6 7 8 9 10 11
+ + COM
D11D12D13
DC24V
ST201 SB1 SB2 SB3
D01 D02 D03
HL1 HL2 12 13 14 15 16 17
▲
Green Red
3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 XT
Intelligent Q F X M
controller
SA
TA
1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 XT
DC24V
+
Power-
module
# #
Hl1: Failure indicator 8 ,9 : Making indicator(capacity AC400V,1A)
HL2: Close indicator 10#, 11#: communication output
# #
HL3: Energy storage indicator 12 , 13 : Signal alarm of load 1 output
SB1: Under-voltage button 14 , 15#: Signal alarm of load 2 output
#
3#,4#,5#: Fault trip contact output(4# common terminal, 33#,34#,35#: Energy storage motor
contact capacity AC230V,5A 36#~40#: Auxiliary contact (capacity:AC230V,5A)
# #
6 , 7 : to be connected with current transformer(N/O auxiliary
contact, capacity AC400V, 1A,when no current transformer)
Note: Dashed is to be connected by users.
.14.
6.2 NA1-2000, 3200, 4000, 6300
motor
Main circuit Over-current release Emergent
disconnection
motor
driven
break
driven
close
auxiliary switch
FU
Power
Processing
unit Intelligent Controller
FU
_ 110V
~
_ 230V
~
Intelligent release power("1"connect positive pole,and"2"connect negative pole for direct current)
~400V
Sb1 Shunt button SB2 Under-voltage button SB3 Making button SA Position switch
Q Under-voltage release or under-voltage time-delay release F Shunt release
X Closing release M Energy-storage motor XT Connection terminal
Note: If control voltage of Q, F, X is different from each other, they can be connected to different power. If model ST intelligent release is DC, it
must pass through U1 and U2 before directly connected to terminal 1 or 2.Circuit explanation for signal output
a.Broken-line parts shall be provided by customers.
b.Terminals 6# ~7# can output NC (normal close) contact if that is required by users.
c.Terminal 35# can be directly connected to power (automatic pre-storing energy), alternatively connect power after connecting NO button (manual-
controlled pre-storing energy).
In order to avoid the damage to shunt release and closing electromagnet, one group of NO (shunt release) or NC (closing electromagnet) contact
should be separately connected to the control circuit.
.15.
Air Circuit Breaker
1 2
L1
N
PE
To T03 busbar 1 2 3 4 5
ST Power Supply Modular IV
L N L N PE
Profibus-DP + - + - + - + -
ST-DP 12 13 14 15 16 17 18 19
Device + - + -
1 2 3 4 5 6 7 8 9 10 11
Special connecting wire
D11D12D13
to the incoming-line side DO24V DO24VCOM
Modbus-RTV PE Un U1 U2 U3 ST201
DO1 DO3
Transformer 12 13 14 15 1 6 17 18 19
connected
Red Green
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
Q F X
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49
Fault Energy-
storage Open Close
FU2
FU1 QF
101 27 Q
L1,L2,L3 28
SB1 F
29 30
139 102
QF SB2 X
31 32
103 107
34 SA 33 171 YE
L11,L12,L13
SA 35
M
TA1 TA2 TA3
46 45 105 GN
47 135 RD
1 2
Processing unit
.16.
QF: Circuit breaker NA1-□
FU1~2: Fuse RT14-20/10A
SB1~2: Button LA18-22 Each one for red and green
YEHL: Signal indicator AD11-25~230V Yellow
GNHL: Signal indicator AD11-25~230V Green
RDHL: Signal indicator AD11-25~230V Red
Number inside the broken-line circle, is the terminal number on terminal block of NA1 body
(Na1 Inner components)
Q: Under-voltage coil~400V
F: Shunt coil~230V
X: Closing release~230V
M: Energy-storage motor~230V
SA: Motor limit switch
45 46
L1,L2,L3 L1,L2,L3 40 39
43 42
SA 35 171
L11,L12,L13 L11,L12,L13 M
46 45 105 IGN
1TA1 1TA2 1TA3 2TA1 2TA2 2TA3
47 135 IRD
1 2
processing unit
.17.
Air Circuit Breaker
7. Installation
7.1 Installation
7.1.1 Unload the breaker from the soleplate of package. If it is drawout type, firstly pull out the handle under the drawer-base of breaker, and
plug it into the hole on central part of plastic cover under the drawer-base crossbeam, anticlockwise turns the handle,body will slowly slide
along the outside of drawer-base. When the guide rod points to separated position and handle can't be rotated any longer, pull out the
handle and firmly grasp the aluminum handle on drawer-base, pull out the breaker body and remove it form the base, then move the base
from the soleplate and clean up the dirty things inside the drawer-base.
Possible positions
7.1.2 Check the insulation resistance with a 500V megger, resistance should not be less than 20MΩwhen ambient temperature is 20℃±5℃and
relative humidity is 50%~70%. Otherwise dry it.
7.1.3 Power supply
NA1 devices can be supplied either from the top or from the bottom without reduction in performance, in order to facilitate connection
when installed in a switchboard.
7.1.4 Put the breaker (fixed-type) or drawer-base (drawout-type) into the installation-bracket, and make it fixed, directly connect the cable wire of
main circuit to the bus wire of fixed-type circuit breaker. Alternatively put breaker body onto the slideway of drawer-base. Plug the handle
into installation hole, clockwise turns it until the under-part of drawer-base points at the connection position and “click”sound is heard. It indicates
that breaker body has been connected to its place, then connect the cable of main circuit to drawer-base.
Mounting the circuit-breaker
It is important to distribute the weight of the device uniformily over a rigid mounting surface such as rails or a base plate.
This mounting plane should be perfectly flat (tolerance on support flatness: 2 mm).This eliminates any risk of deformation which could interfere
with correct operation of the circuit breaker.
NA1 devices can also be mounted on a vertical plane using the special brackets.
.18.
Mounting with vertical brackets Mounting on rails
7.1.5 Partitions
Sufficient openings must be provided in partitions to ensure
good air circulation around the circuit breaker;Any partition
between upstream and downstream connections of the device
must be made of nonmagnetic material.
For high-currents, of 2500 A and upwards, the metal supports or
barriers in the immediate vicinity of a conductor must be made of
non-magnetic material A;Metal barriers through which a conductor Busbars
passes must not form a magnetic loop. The mechanical connection must be exclude the possibility of
formation of a magnetic loop around a conductor
B C B
.19.
Air Circuit Breaker
7.1.8 Clamping
Correct clamping of busbars depends on the tightening torques used for
1 2 3 4
the nuts and bolts,etc. Over-tightening may have the same consequences as
under-tightening.
For connecting busbars to the circuit breaker, the tightening torques to be used
are shown in the table below.These values are for use with copper busbars and
steel nuts and bolts, class 8.8.
1 breaker terminal
2 busbar
3 bolt
4 washer
5 nut
5
Examples
.20.
Connected position Test position Disconnected position Drawout position
Main body
Drawer seat
Handle Slideway
.21.
Air Circuit Breaker
Making the secondary circuit power, the motor-driven mechanism can Manual energy-storage
store energy automatically until hearing the click and energy stored
"indicating on the panel. Otherwise press the storage handle for 6
times until hearing the click and the indicator display energy stored”
And the closing operation can be realized either by closing
electromagnet or manual button.
Note: the specifications in the table is obtained as the ambient temperature of air circuit breaker is 40℃, with open installation; this is in
compliance with the specification of copper busbars adopted under the heating conditions regulated in IEC/EN60947-2.
9. Power loss
Inm(A) NA1-1000 NA1-2000 NA1-3200 NA1-4000 NA1-6300
In(A) 200 400 630 800 1000 630 800 1000 1250 1600 2000 2000 2500 3200 4000/3P 4000/4P 4000 5000 6300
Power Drawer type 40 101 123 110 177 70 110 172 268 440 530 384 600 737 921 900 575 898 1426
loss (W) Fixed type 33 85 107 94 476 34.4 50 78 122 200 262 200 312 307 - - - - -
341
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
20 40 60 80 100 120 Is(kA)
.22.
11. Temperature compensation correction
Ambient NA1-3200
Standard NA1-1000 NA1-2000 NA1-6300
temperature NA1-4000
40℃ 200 400 630 800 1000 630 800 1000 1250 1600 2000 2000 2500 3200 4000 4000 5000 6300
45℃ 195 395 623 790 985 630 800 1000 1250 1600 1900 2000 2400 3000 3800 4000 5000 6000
50℃ 192 384 605 768 960 630 800 1000 1250 1500 1900 2000 2300 3000 3600 4000 5000 5600
IEC/EN60947-2
55℃ 182 328 584 725 924 630 800 1000 1200 1500 1800 2000 2200 2800 3400 4000 4800 5400
60℃ 174 248 548 696 870 610 800 1000 1150 1300 1700 2000 2200 2800 3200 4000 4800 5200
65℃ 163 192 500 620 810 610 800 1000 1150 1300 1650 2000 2200 2600 3200 4000 4800 5100
Note: The ACB is to calibrated at 40℃, special application please refer to the table above and the curve below.
5000 7000
4800 6800
4600 6600
4400 6400
4200 6200
4000 In=4000A 6000 In=6300A
3800 5800
Rated current (A)
3600 5600
3400 5400
3200 In=3200A 5200 In=5000A
3000 5000
2800 4800
2600 In=2500A 4600
2400 4400
2200 4200
In=2000A In=4000A
2000 4000
1800 3800
40 45 50 55 60 65 70 40 45 50 55 60 65 70
.23.
Air Circuit Breaker
.24.
Type of air circuit Number and area of the Breaking capacity of
Air circuit breaker
breaker for busbar for main circuit air circuit breaker
for branch circuit
main circuit (n×W×T) for branch circuit (kA)
NA1-1000-400 9
NA1-1000-400 240mm 2
18.5 NA1, NM8
NA1-1000-400 27.5
NA1-1000-630 11.4
NA1-1000-630 300mm 2 22.7 NA1, NM8
NA1-1000-630 34.1
NA1-1000-630 14.4
NA1-1000-630 30×10 28.8 NA1, NM8
NA1-1000-630 43.2
NA1-1000-800 18
NA1-1000-800 2×40×5 36.1 NA1, NM8
NA1-1000-800 54.1
NA1-1000-1000 22.7
NA1-1000-1000 2×50×5 44.5 NA1, NM8
NA1-2000-1000 67.2
NA1-2000-1250 19.3
NA1-2000-1250 3×50×5 38.5 NA1, NM8
NA1-2000-1250 57.8
NA1-2000-1600 24
NA1-2000-1600 2×60×10 48.1 NA1, NM8
NA1-2000-1600 72.1
NA1-2000-2000 30
NA1-2000-2000 2×80×10 60.1 NA1, NM8
NA1-2000-2000 90.1
NA1-3200-2500 36.5
NA1-3200-2500 2×100×10 73 NA1, NM8
NA1-3200-2500 109.5
NA1-3200-3200 48.2
NA1-3200-3200 2×120×10 96.3 NA1, NM8
NA1-3200-3200 144.5
NA1-4000-4000 60
2×(2×80×10) NA1, NM8
NA1-4000-4000 120
NA1-6300-5000 75.8
2×(2×120×10) NA1, NM8
NA1-6300-5000 151.6
.25.
Air Circuit Breaker
Rated
400 630 800 1000 1250
current (A)
Delayed tripping
0.1, 0.2, 0.3, 0.4
time (s)
Returnable time 0.06, 0.14, 0.23, 0.35
.26.
NA1-3200 NA1-4000 NA1-6300
1600 2000 2000 2500 3200 3200 4000 4000 5000 6300
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.656~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.725~24 1.725~30 1.725~30 1.725~37.7 1.725~48 1.725~48 1.725~60 1.725~60 1.725~75 1.725~94.5
2.07~24 2.07~30 2.07~30 2.07~37.7 2.07~48 2.07~48 2.07~60 2.07~60 2.07~75 2.07~94.5
1.6~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
1.656~24 2~30 2~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
2.208~24 2.208~30 2.208~30 2.5~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
2.65~24 2.65~30 2.65~30 2.65~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
2.76~24 2.76~30 2.76~30 2.76~37.7 3.2~48 3.2~48 4~60 4~60 5~75 6.3~94.5
3.312~24 3.312~30 3.312~30 3.312~37.7 3.312~48 3.312~48 4~60 4~60 5~75 6.3~94.5
3.45~24 3.45~30 3.45~30 3.45~37.7 3.45~48 3.45~48 4~60 4~60 5~75 6.3~94.5
4.14~24 4.14~30 4.14~30 4.14~37.7 4.14~48 4.14~48 4.14~60 4.14~60 5~75 6.3~94.5
.27.
Air Circuit Breaker
Rated
400 630 800 1000 1250
current (A)
Delayed tripping
0.1, 0.2, 0.3, 0.4
time (s)
Returnable time 0.06, 0.14, 0.23, 0.35
.28.
NA1-3200 NA1-4000 NA1-6300
1600 2000 2000 2500 3200 3200 4000 4000 5000 6300
3.45~24 3.45~30 3.45~30 3.45~37.7 3.45~48 3.45~48 4~60 4~60 5~75 6.3~94.5
4.14~24 4.14~30 4.14~30 4.14~37.7 4.14~48 4.14~48 4.14~60 4.14~60 5~75 6.3~94.5
4.347~24 4.347~30 4.347~30 4.347~37.7 4.347~48 4.347~48 4.347~60 4.347~60 5~75 6.3~94.5
5.216~24 5.216~30 5.216~30 5.216~37.7 5.216~48 5.216~48 5.216~60 5.216~60 5.216~75 6.3~94.5
4.83~24 4.83~30 4.83~30 4.83~37.7 4.83~48 4.83~48 4.83~60 4.83~60 5~75 6.3~94.5
5.796~24 5.796~30 5.796~30 5.796~37.7 5.796~48 5.796~48 5.796~60 5.796~60 5.796~75 6.3~94.5
5.52~24 5.52~30 5.52~30 5.52~37.7 5.52~48 5.52~48 5.52~60 5.52~60 5.52~75 6.3~94.5
6.624~24 6.624~30 6.624~30 6.624~37.7 6.624~48 6.624~48 6.624~60 6.624~60 6.624~75 6.624~94.5
6.9~24 6.9~30 6.9~30 6.9~37.7 6.9~48 6.9~48 6.9~60 6.9~60 6.9~75 6.9~94.5
8.28~24 8.28~30 8.28~30 8.28~37.7 8.28~48 8.28~48 8.28~60 8.28~60 8.28~75 8.28~94.5
8.694~24 8.694~30 8.694~30 8.694~37.7 8.694~48 8.694~48 8.694~60 8.694~60 8.694~75 8.694~94.5
10.44~24 10.44~30 10.44~30 10.44~37.7 10.44~48 10.44~48 10.44~60 10.44~60 10.44~75 10.44~94.5
8.694~24 8.694~30 8.694~30 8.694~37.7 8.694~48 8.694~48 8.694~60 8.694~60 8.694~75 8.694~94.5
10.44~24 10.44~30 10.44~30 10.44~37.7 10.44~48 10.44~48 10.44~60 10.44~60 10.44~75 10.44~94.5
9.66~24 9.66~30 9.66~30 9.66~37.7 9.66~48 9.66~48 9.66~60 9.66~60 9.66~75 9.66~94.5
11.59~24 11.59~30 11.59~30 11.59~37.7 11.59~48 11.59~48 11.59~60 11.59~60 11.59~75 11.59~94.5
11.04~24 11.04~30 11.04~30 11.04~37.7 11.04~48 11.04~48 11.04~60 11.04~60 11.04~75 11.04~94.5
13.25~24 13.25~30 13.25~30 13.25~37.7 13.25~48 13.25~48 13.25~60 13.25~60 13.25~75 13.25~94.5
13.8~24 13.8~30 13.8~30 13.8~37.7 13.8~48 13.8~48 13.8~60 13.8~60 13.8~75 13.8~94.5
16.56~24 16.56~30 16.56~30 16.56~37.7 16.56~48 16.56~48 16.56~60 16.56~60 16.56~75 16.56~94.5
17.25~24 17.25~30 17.25~30 17.25~37.7 17.25~48 17.25~48 17.25~60 17.25~60 17.25~75 17.25~94.5
20.7~24 20.7~30 20.7~30 20.7~37.7 20.7~48 20.7~48 20.7~60 20.7~60 20.7~75 20.7~94.5
.29.
Air Circuit Breaker
Rated
400 630 800 1000 1250
current (A)
Delayed tripping
0.1, 0.2, 0.3, 0.4
time (s)
Returnable time 0.06, 0.14, 0.23, 0.35
Note: It can satisfy the selective protection if only the short time-delay setting value of the superior breaker 1.32 times more than the subordinate breaker,
when the instantaneous setting value is adjustive.
.30.
NA1-3200 NA1-4000 NA1-6300
1600 2000 2000 2500 3200 3200 4000 4000 5000 6300
6.348~24 6.348~30 6.348~30 6.348~37.7 6.348~48 6.348~48 6.348~60 6.348~60 6.348~75 6.348~94.5
9.998~24 9.998~30 9.998~30 9.998~37.7 9.998~48 9.998~48 9.998~60 9.998~60 9.998~75 9.998~94.5
12.696~24 12.696~30 12.696~30 12.696~37.7 12.696~48 12.696~48 12.696~60 12.696~60 12.696~75 12.696~94.5
15.87~24 15.87~30 15.87~30 15.87~37.7 15.87~48 15.87~48 15.87~60 15.87~60 15.87~75 15.87~94.5
19.837~24 19.837~30 19.837~30 19.837~37.7 19.837~48 19.837~48 19.837~60 19.837~60 19.837~75 19.837~94.5
25.392~30 25.392~30 25.392~37.7 25.392~48 25.392~48 25.392~60 25.392~60 25.392~75 25.392~94.5
31.74~37.7 31.74~48 31.74~48 31.74~60 31.74~60 31.74~75 31.74~94.5
31.74~37.7 31.74~48 31.74~48 31.74~60 31.74~60 31.74~75 31.74~94.5
39.675~48 39.675~48 39.675~60 39.675~60 39.675~75 39.675~94.5
50.784~60 50.784~60 50.784~75 50.784~94.5
50.784~60 50.784~60 50.784~75 50.784~94.5
63.48~75 63.48~94.5
63.48~75 63.48~94.5
79.35~94.5
.31.