Professional Documents
Culture Documents
60MK183
Copyright © SUZUKI (MYANMAR) MOTOR CO., LTD. 2016 All Rights Reserved
No part of this document may be reproduced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, without the express written permission of SUZUKI (MYANMAR) MOTOR CO., LTD.
60MK1-82E
FOREWORD IMPORTANT
This manual should be considered a per- All information in this manual is based WARNING/ CAUTION/NOTICE/
manent part of the vehicle and should on the latest product information avail- NOTE
remain with the vehicle when resold or oth- able at the time of publication. Due to Please read this manual and follow its
erwise transferred to a new owner or oper- improvements or other changes, there instructions carefully. To emphasize spe-
ator. Please read this manual carefully may be discrepancies between informa- cial information, the symbol and the
before operating your new SUZUKI and tion in this manual and your vehicle. words WARNING, CAUTION, NOTICE
review the manual from time to time. It SUZUKI (MYANMAR) MOTOR CO., LTD. and NOTE have special meanings. Pay
contains important information on safety, reserves the right to make production particular attention to messages high-
operation and maintenance. changes at any time, without notice and lighted by these signal words:
without incurring any obligation to
make the same or similar changes to WARNING
SUZUKI (MYANMAR) MOTOR CO., LTD. vehicles previously built or sold.
Indicates a potential hazard that
This vehicle may not comply with stan- could result in death or serious
dards or regulations of other countries. injury.
Before attempting to register this vehi-
cle in any other country, check all appli-
cable regulations and make any CAUTION
necessary modifications. Indicates a potential hazard that
could result in minor or moderate
injury.
NOTICE
Indicates a potential hazard that
could result in vehicle damage.
NOTE:
Indicates special information to make
maintenance easier or instructions clearer.
60MK1-82E
MODIFICATION WARNING
WARNING
Do not modify this vehicle. Modifica-
tion could adversely affect safety,
handling, performance, or durability
and may violate governmental regula-
tions. In addition, damage or perfor-
mance problems resulting from
modification may not be covered
under warranty.
75F135
NOTICE
The circle with a slash in this manual
Improper installation of mobile com-
means “Don’t do this” or “Don’t let this hap-
pen”. munication equipment such as cellu-
lar telephones or CB (Citizen’s Band)
radios may cause electronic interfer-
ence with your vehicle’s ignition sys-
tem, resulting in vehicle performance
problems. Consult your SUZUKI
dealer or qualified service technician
for advice on installing such mobile
communication equipment.
60MK1-82E
INTRODUCTION
Thank you for choosing SUZUKI and welcome to our growing family. Your choice was a wise one; SUZUKI products are a great value
that will give you years of driving pleasure.
This Owner’s Manual was prepared to help you have a safe, enjoyable, and trouble-free experience with your SUZUKI. In it you will learn
about the vehicle’s operation, its safety features and maintenance requirements. Please read it carefully before operating your vehicle.
Afterwards, keep this Manual in the glove box for future reference.
Should you resell the vehicle, please leave this Manual with it for the next owner.
In addition to the Owner’s Manual, the other booklets provided with your SUZUKI explain the vehicle’s warranties. We recommend you
read them as well to familiarize yourself with this important information.
When planning the regular scheduled maintenance of your SUZUKI, we recommend you visit your local SUZUKI dealership. Their fac-
tory-trained technicians will provide the best possible service and use only genuine SUZUKI parts and accessories.
60MK1-82E
RECOMMENDATION OF GENUINE SUZUKI PARTS AND ACCESSORIES USE
SUZUKI strongly recommends the use of genuine SUZUKI parts and accessories. Genuine SUZUKI parts and accessories are built to
the highest standards of quality and performance, and are designed to fit your vehicle’s exact specifications.
A wide variety of non-genuine replacement parts and accessories for SUZUKI vehicles are currently available in the market. Using these
parts and accessories can affect the vehicle performance and shorten its useful life. Therefore, installation of non-genuine SUZUKI parts
and accessories is not covered under warranty.
60MK1-82E
Suzuki recommends genuine parts and
oil/chemical to maintain high levels of
safety, reliability, comfort and performance.
Authorized Suzuki dealers will be pleased to help you with Suzuki service. With their expertise and experience, Suzuki dealers
can offer you the best service to ensure a safe and comfortable driving experience.
60MK1-82E
SERVICE STATION GUIDE
1. Fuel (see section 1)
2. Engine hood (see section 5)
3. Tire changing tools (see section 8)
4. Engine oil dipstick <Yellow>
(see section 7)
5. Automatic transaxle fluid dipstick
<Red> (see section 7)
6. Engine coolant (see section 7) 3
7
7. Windshield washer fluid
(see section 7)
8. Battery (see section 7)
9. Tire pressure (see Tire Information 4
2
Label on driver’s door lock pillar)
10. Spare tire (see section 8) 5 10
6 8 2 1
9 1
60MK100
60MK1-82E
TABLE OF CONTENTS FUEL RECOMMENDATION 1
BEFORE DRIVING 2
DRIVING TIPS 4
EMERGENCY SERVICE 8
APPEARANCE CARE 9
GENERAL INFORMATION 10
SPECIFICATIONS 11
INDEX 12
60MK1-82E
ILLUSTRATED TABLE OF CONTENTS
EXTERIOR
1. Rear Window Wiper (P.2-63)
2. High-mount Stop Light (P.7-28)
3. Radio Antenna (P.5-7)
4. Engine Hood (P.5-10)
5. Headlight (P.2-59, 7-25) 1 2 3 4 5 6 7
6. Windshield Wiper (P.2-62)
7. Fuel Filler Cap (P.5-9)
8. Parking Sensor (P.3-15)
9. License Plate Light (P.7-27)
10. Tailgate (P.2-5)
11. Rear Combination Light (P.7-27)
12. Front Fog Light (P.2-60, 7-27)
13. Outside Rearview Mirror (P.2-17)
14. Door Locks (P.2-3)
8 9 10 11 12 13 14
EXAMPLE
60MK184
60MK1-82E
ILLUSTRATED TABLE OF CONTENTS
INTERIOR
1. Interior Light (P.5-12, 7-24) 5. Electric Mirrors Control Switch (P.2-17)/ 9. Parking Brake Lever (P.3-8)
2. Seat Belts (P.2-25) Electric Window Controls (P.2-15) 10. Front Seats (P.2-18)
3. Assist Grips (P.5-14) 6. Sun Visor (P.5-11) 11. Gearshift Lever (P.3-13)
4. Overhead Rear Air Conditioning Sys- 7. Inside Rearview Mirror (P.2-17)
tem (P.5-3) 8. Rear Seats (P.2-20)
EXAMPLE 1 2 3 4 5 6 1 7
8 2 8 9 10 11
60MK197
60MK1-82E
ILLUSTRATED TABLE OF CONTENTS
INSTRUMENT PANEL
1. Lighting Control Lever (P.2-59)/
Turn Signal Control Lever (P.2-60)
2. Front Air Bags (P.2-38)
3. Instrument Cluster (P.2-43)
4. Windshield Wiper and Washer Lever
(P.2-62)/Rear Window Wiper and
Washer Switch (P.2-63) 1 2 3 4 5 6 2
5. Audio (if equipped) (P.5-8)
6. Hazard Warning Switch (P.2-61)
7. Remote Audio Controls
8. Front Fog Light Switch (P.2-60)
9. Fuse Box (P.7-21)
10. Engine Hood Release Handle
(P.5-10)
11. Parking Sensor Switch (P.3-17)
12. Tilt Steering Lock Lever (P.2-64)
13. Engine Switch (P.3-3)
14. Manual Heating and Air Conditioning
System (P.5-1)
15. Universal Serial Bus (USB) Socket
(P.5-14)
16. Accessory Socket (P.5-13)
17. Heated Rear Window Switch (P.2-65)
18. Glove Box (P.5-15)
7 8 9 10 11 12 13 14 15 16 17 18
EXAMPLE
60MK186
60MK1-82E
FUEL RECOMMENDATION
FUEL RECOMMENDATION 1
Fuel Recommendation ........................................................ 1-1
65D394
60MK1-82E
FUEL RECOMMENDATION
1-1
60MK1-82E
BEFORE DRIVING
BEFORE DRIVING
Keys ...................................................................................... 2-1
Door Locks .......................................................................... 2-3 2
Keyless Push Start System Remote Controller ............... 2-6
Theft Deterrent Alarm System ........................................... 2-12
Windows .............................................................................. 2-15
Mirrors .................................................................................. 2-17
Front Seats .......................................................................... 2-18
Rear Seats ............................................................................ 2-20
Seat Belts and Child Restraint Systems ........................... 2-25
Supplemental Restraint System (air bags) ....................... 2-37
Instrument Cluster .............................................................. 2-43
Warning and Indicator Lights ............................................ 2-44
Speedometer ....................................................................... 2-49
Tachometer .......................................................................... 2-50
60G404 Fuel Gauge ........................................................................... 2-50
Temperature Gauge ............................................................ 2-51
Brightness Control .............................................................. 2-51
Information Display ............................................................. 2-52
Lighting Control Lever ........................................................ 2-59
Front Fog Light Switch ....................................................... 2-60
Turn Signal Control Lever .................................................. 2-60
Hazard Warning Switch ...................................................... 2-61
Windshield Wiper and Washer Lever ................................ 2-62
Tilt Steering Lock Lever ..................................................... 2-64
Horn ...................................................................................... 2-64
Heated Rear Window Switch .............................................. 2-65
60MK1-82E
BEFORE DRIVING
(1)
(5)
(2) 57L21003
60MK152
The key identification number (4) is
Your vehicle comes with two identical key- 57L21016 stamped on a metal tag (5) provided with
less push start system remote controllers the keys. Keep the tag in a safe place. If
(1), each with a detachable key (2) housed To stow the key into the remote controller,
you lose your keys, you will need this num-
inside. push the key in the remote controller until
ber to have new keys made. Write the
you hear a click.
number below for your future reference.
KEY NUMBER:
(3)
60MK153
2-1
60MK1-82E
BEFORE DRIVING
Immobilizer System If the light still blinks after the ignition mode
This system is designed to help prevent is changed back to “ON”, there may be NOTICE
vehicle theft by electronically disabling the something wrong with your key or with the
engine starting system. immobilizer system. Ask your SUZUKI The remote controllers are sensitive
The engine can be started only with your dealer to have the system inspected. electronic instruments. To avoid
vehicle’s original keyless push start system damaging them:
The immobilizer/keyless push start system • Do not expose them to impacts,
remote controller which has an electronic warning light may also blinks if the remote
identification code programmed into it. The moisture or high temperature such
controller is not in the vehicle when you as on the dashboard under direct
remote controller communicates the identi- close the door or attempt to start the
fication code to the vehicle when the sunlight.
engine. • Keep them away from magnetic
engine switch is pressed to change the
ignition mode to “ON”. If you need to make objects.
NOTE:
spare keys or remote controllers, see your • If you lose your remote controller, see
SUZUKI dealer. The vehicle must be pro- This immobilizer system, model 37290-
your SUZUKI dealer as soon as possible 79M0 is in compliance with the essential
grammed with the correct identification to have the lost one deactivated, then
code for the spare. A key made by an ordi- requirements and other provisions of the
have the new remote controller made by Directive 1999/5/EC.
nary locksmith will not work. them.
• If you own other vehicles with immobi-
lizer keys, keep those keys away from
the engine switch when using your
SUZUKI, or the engine may not be
started because they may interfere with
your SUZUKI’s immobilizer system.
• If you attach any metal objects to the
80JM122 remote controller, it may not start the
If the immobilizer/keyless push start sys- engine.
tem warning light blinks when the ignition
mode is “ON”, the engine will not start.
If this light blinks, change the ignition mode
to “LOCK” (OFF), then change back to
“ON”. Also refer to “If the “PUSH” indicator
light blinks and the engine cannot be
started” in “Starting the Engine (Vehicle
with Keyless Push Start System)” in the
“OPERATING YOUR VEHICLE” section.
2-2
60MK1-82E
BEFORE DRIVING
(3)
(1)
(3)
(4)
(4)
60MK103
EXAMPLE
EXAMPLE (1) LOCK 60MK144
2-3
60MK1-82E
BEFORE DRIVING
EXAMPLE
60MH006
(1)
(2) (1) LOCK
(2) UNLOCK
2-4
60MK1-82E
BEFORE DRIVING
Tailgate
EXAMPLE
WARNING
Always make sure that the tailgate is
closed and latched securely. Com-
pletely closing the tailgate helps pre-
vent occupants from being thrown
from the vehicle in the event of an
accident. Completely closing it also (1)
helps keep exhaust gases from enter-
ing the vehicle.
(2)
60MK198 60MH008
You can lock and unlock the tailgate by 2) Push open the tailgate from inside by
using the key in the driver’s door lock. pushing up on the emergency lever (2)
using a flat blade screwdriver or the
To open the tailgate, pull up and hold the jack handle. The tailgate will be latched
tailgate handle (1) and lift the tailgate. again by closing the tailgate simply.
If you cannot unlatch the tailgate by pulling If the tailgate cannot be unlatched by pull-
up the tailgate handle (1) due to a dis- ing up the tailgate handle (1), have the
charged battery or malfunction, follow the vehicle inspected by your SUZUKI dealer.
procedures below to unlatch the tailgate
from inside the vehicle.
CAUTION
1) Fold the 3rd row seat forward for easier • To avoid injury, do not use your fin-
access. Refer to “Folding Rear Seats” ger to push the emergency lever.
section for details on how to fold the 3rd • Make sure there is no one near the
row seat forward. tailgate when pushing open the tail-
gate from inside the vehicle.
2-5
60MK1-82E
BEFORE DRIVING
Keyless Push Start System The remote controller enables the follow- Central door locking system
ing operations: • To lock all doors, push the “LOCK” but-
Remote Controller • You can lock or unlock the doors by ton (1) once.
operating the LOCK/UNLOCK buttons • To unlock only the driver’s door, push the
WARNING on the remote controller. Refer to the “UNLOCK” button (2) once.
explanation in this section. • To unlock other doors, push the
Radio waves from the keyless push • You can lock or unlock the doors by “UNLOCK” button (2) once again.
start system antenna(s) may interfere pushing the request switch. For details,
with operation of electrical medical refer to the explanation in this section. NOTE:
equipment such as pacemakers. Fail- • You can start the engine without using You can switch the function that unlocks all
ure to take the precautions listed an ignition key. For details, refer to doors from twice operations to once opera-
below can increase the risk of severe “Engine Switch” in the “OPERATING tion, and vice versa, via the setting mode
injury or death due to radio wave YOUR VEHICLE” section. of the information display. For details on
interference. how to use the information display, refer to
• Anyone who uses electrical medi- “Information Display” in this section.
cal equipment such as a pace-
maker should consult the medical The turn signal lights will flash once and
equipment supplier or their medical (2) the exterior buzzer will sound once when
advisor about whether radio waves the doors are locked.
from the antenna(s) can interfere
with the medical equipment. (1)
When the doors are unlocked:
• If radio wave interference is a con- • The turn signal lights will flash twice and
cern, have the function of the the exterior buzzer will sound twice.
antenna(s) disabled by your • If the interior light switch is in the
SUZUKI dealer. “DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you press the engine switch
68LM206 during this time, the light will start to fade
(1) “LOCK” button out immediately.
(2) “UNLOCK” button
2-6
60MK1-82E
BEFORE DRIVING
Be sure the doors are locked after you Keyless unlocking/locking using the To unlock a door or all doors:
operate the “LOCK” button (1). request switches • Push one of the request switches once
If no door is opened within about 30 sec- to unlock only one door.
onds after the “UNLOCK” button (2) is • Push one of the request switches twice
operated, the doors will automatically lock to unlock all doors.
again.
NOTE:
NOTE: You can switch the function that unlocks all
You can set whether the exterior buzzer doors from twice operations to once opera-
sounds when locking or unlocking the tion, and vice versa, via the setting mode
doors via the setting mode of the informa- of the information display. For details on
tion display. For details on how to use the how to use the information display, refer to
information display, refer to “Information “Information Display” in this section.
Display” in this section. (1) EXAMPLE When the doors are unlocked:
NOTE: 60MK188
• The turn signal lights will flash twice and
• The maximum operating distance of the the exterior buzzer will sound twice.
remote controller is about 5 m (16 ft.), When the remote controller is within the • If the interior light switch is in the
but this can vary depending on the sur- operating range described in this section, “DOOR” position, the interior light will
roundings, especially near other trans- you can lock or unlock the doors (including turn on for about 15 seconds and then
mitting devices such as radio towers or the tailgate) by pushing the request switch fade out. If you press the engine switch
CB (Citizen’s Band) radios. (1) on the driver’s door handle, front pas- during this time, the light will start to fade
• The door locks cannot be operated with senger’s door handle or tailgate. out immediately.
the remote controller if the ignition mode To lock all doors when all doors are Be sure the doors are locked after you
is other than the “LOCK” (OFF). unlocked: operate the request switch to lock the
• When any door is open, if you push the • To lock all doors, push one of the doors.
“LOCK” button on the remote controller, request switches once.
the exterior buzzer will sound and doors
The turn signal lights will flash once and NOTE:
cannot be locked.
the exterior buzzer will sound once when • The door locks cannot be operated by
• If you lose one of the remote controllers,
the doors are locked. the request switch under the following
ask your SUZUKI dealer as soon as pos-
conditions:
sible for a replacement. Be sure to have
– If any door is open or is not completely
your dealer program the new remote
closed.
controller code in your vehicle’s memory
– If the ignition mode is other than
so that the old code is erased.
“LOCK” (OFF).
2-7
60MK1-82E
BEFORE DRIVING
2-8
60MK1-82E
BEFORE DRIVING
• Be sure that the driver always carries the Press the request switch again after doing
remote controller. the following:
• If you lose one of the remote controllers, With the ignition mode changed to “LOCK”
ask your SUZUKI dealer as soon as pos- (OFF) by pressing the engine switch, bring
sible for a replacement. Be sure to have (A) out the remote controller if it is inside the
your dealer program the new remote vehicle and check that all doors are com-
controller code in your vehicle’s memory pletely closed.
so that the old code is erased.
• You can use up to four remote control- Reminder function
lers and the keys for your vehicle. Ask
your SUZUKI dealer for details.
• The battery life of the remote controller
is about two years, but it can vary
68LM247
depending on usage conditions.
To remove the key from the remote control-
ler, push the button (A) in the direction of
the arrow and pull the key out from the
remote controller.
2-9
60MK1-82E
BEFORE DRIVING
The indicator light will turn off within sev- Replacement of the battery
eral seconds after the remote controller is If the remote controller becomes unreli-
returned to interior workable area. able, replace the battery.
If the remote controller is left in the vehicle To replace the battery of the remote con-
and you lock the driver’s door or front pas- troller:
senger’s door as described below, the door
will be automatically unlocked. (1)
• If you open the driver’s door and lock the
door by turning the lock knob forward or
pushing the power door locking switch,
the driver’s door will be automatically
unlocked.
• If you open the front passenger’s door
and lock the door by turning the lock 68LM210
knob forward or pushing the power door
locking switch, the front passenger’s (1) Lithium disc type battery:
door will be automatically unlocked. CR2032 or equivalent
2-10
60MK1-82E
BEFORE DRIVING
NOTICE
The remote controller is a sensitive
electronic instrument. To avoid dam-
aging it, do not expose it to dust or 80JM133
moisture or tamper with internal parts.
(1) Crossed-out wheeled bin symbol
NOTE: The crossed-out wheeled bin symbol (1)
Used batteries must be disposed properly indicates that used battery should be col-
according to applicable rules or regulations lected separately from ordinary household
and must not be disposed with ordinary trash.
household trash.
By ensuring the used battery is disposed
or recycled correctly, you will help prevent
potential negative consequences for the
environment and human health, which
could otherwise be caused by inappropri-
ate trash handling of the battery. The recy-
cling of materials will help to conserve
natural resources. For more detailed infor-
mation about disposing or recycling of the
used battery, consult your SUZUKI dealer.
2-11
60MK1-82E
BEFORE DRIVING
Theft Deterrent Alarm System NOTE: How to arm the theft deterrent alarm
• The theft deterrent alarm system gener- system (when enabled)
The theft deterrent alarm system is armed ates alarms when any of the predeter- Lock the doors using the keyless push
in about 20 seconds after you lock the mined conditions is met. However, the start system remote controller or the
doors. system does not have any function of request switch. The theft deterrent light (1)
Keyless push start system – Use the blocking unauthorized entry into your will start blinking, and the theft deterrent
remote controller or push the request vehicle. alarm system will be armed in about 20
switch on the driver’s door, passenger’s • Always use the keyless push start sys- seconds.
door or tailgate. tem remote controller or the request While the system is being armed, the indi-
Once the system is armed, any attempt to switch to unlock the doors when the theft cator continues to blink at approximately 2-
open a door by using any other means (*) deterrent alarm system has been armed. second intervals.
than the keyless push start system remote Using a key instead will trigger the
controller or the request switch will cause alarm.
the alarm to be triggered. • If a person who does not know the theft
* These means include the following: deterrent alarm system is going to drive
– The key your vehicle, we recommend you explain
– The lock lever on a door the system and its operation to the per-
– The power door locking switch son, or disable the system beforehand.
Mistakenly triggering the alarm may
cause a nuisance to others.
• Even if the theft deterrent alarm system
is armed, you should still be careful to (1)
guard against theft. Do not leave money
or things of value in your vehicle.
71LST0203
2-12
60MK1-82E
BEFORE DRIVING
NOTE: How to stop the alarm Checking whether the alarm has been
• To prevent the alarm from being acci- Should the alarm be triggered accidentally, triggered during parking
dentally triggered, avoid arming it while unlock the doors using the keyless push If the alarm was triggered due to an unau-
anyone remains inside the vehicle. The start system remote controller or the thorized entry into the vehicle and you then
alarm will be triggered if any person request switch, or press the engine switch press the engine switch to change the igni-
inside unlocks a door by operating the to change the ignition mode to “ON”. The tion mode to “ON”, the theft deterrent light
lock lever or power door locking switch. alarm will then stop. will blink rapidly for about 8 seconds and a
• The theft deterrent alarm system is not buzzer will beep 4 times during this period.
armed when all doors are locked using NOTE: If this happens, check whether your vehi-
the key from outside, or using the door • Even after the alarm has stopped, if you cle has been broken into while you were
lock levers or the power door locking lock the doors using the keyless push away from it.
switch from inside. start system remote controller or the
• If any of the doors is not operated within request switch, the theft deterrent alarm Enabling and disabling the theft deter-
approximately 30 seconds after the system will be rearmed with a delay of rent alarm system
doors have been unlocked using the about 20 seconds. The theft deterrent alarm system can be
keyless push start system remote con- • If you disconnect the battery while the either “enabled” or “disabled”.
troller or the request switch, the doors theft deterrent alarm system is in the
are automatically locked again. At the armed condition or the alarm is actually When enabled (factory setting)
same time, the theft deterrent alarm sys- in operation, the alarm will be triggered When the system is enabled, it causes the
tem is armed if the system is in the or re-triggered when the battery is then hazard warning lights to flash for about 40
enabled state. reconnected, although, in the latter case, seconds if any of the alarm trigger condi-
the alarm remains stopped for the period tions is met. The system also causes the
How to disarm the theft deterrent alarm between disconnection and reconnec- interior buzzer to beep intermittently for
system tion of the battery. about 10 seconds, which is followed by
Simply unlock the doors using the keyless • Even after the alarm has stopped at the intermittent sounding of the horn for about
push start system remote controller or the end of the predetermined operation time, 30 seconds.
request switch. The theft deterrent light will it will be triggered again if any door is The theft deterrent light continues to blink
go out, indicating that the theft deterrent opened without disarming the theft during this time.
alarm system is disarmed. deterrent alarm system.
When disabled
When the system is disabled, it stays dis-
armed even if you perform any system
arming operation.
2-13
60MK1-82E
BEFORE DRIVING
How to switch the state of the theft 1) With the ignition mode “ON”, close all
deterrent alarm system EXAMPLE the doors and turn the lock knob (1) on
You can switch the theft deterrent alarm the driver’s door in the unlocking direc-
system from the enabled state to the dis- tion (2) (rearward). Turn the knob on
(3)
abled state, and vice versa, using the fol- (2) the lighting control lever to the OFF
lowing method. position (5).
(4)
NOTE:
(3) All operations included in the following
(2) steps 2) and 3) must be completed within
15 seconds.
2-14
60MK1-82E
BEFORE DRIVING
Every time you perform the series of the Windows Passenger’s door
above steps, the state of the theft deterrent
alarm system changes from the currently Electric Window Controls EXAMPLE
(5)
selected one to the other. You can check The electric windows can only be operated
whether the system is enabled or disabled when the ignition mode is “ON”.
by the number of interior buzzer beeps at
the end of the procedure as follows. Driver’s side
EXAMPLE
System state Number of beeps
(1)
Disabled Once (3)
Enabled 4 times
60MK110
2-15
60MK1-82E
BEFORE DRIVING
Lock switch
WARNING
CLOSE EXAMPLE
• You should always lock the pas-
senger’s window operation when
there are children in the vehicle.
Children can be seriously injured if
they get part of their body caught
by the window during operation.
OPEN • To avoid injuring an occupant by
window entrapment, be sure no
part of the occupant’s body such as
hands or head is in the path of the
electric windows when closing
81A009
them.
60MK154 • Always take the keyless push start
To open a window, push the top part of the system remote controller with you
The driver’s door also has a lock switch for
switch and to close the window lift up the when leaving the vehicle even if
the passenger’s windows. When you push
top part of the switch. only for a short time. Also do not
in the lock switch, the passenger’s win-
The driver’s window has an “auto-down” leave children alone in a parked
dows cannot be raised or lowered by oper-
feature for added convenience (at toll vehicle. Unattended children could
ating any of the switches (2), (3), (4) or (5).
booths or drive-through restaurants, for use the electric window switches
To restore normal operation, release the
example). This means you can open the and get trapped by the window.
lock switch by pushing again.
window without holding the window switch
in the “Down” position. Press the driver’s NOTE:
window switch completely down and If you drive with one of the rear windows
release it. To stop the window before it open, you may hear a loud sound caused
reaches the bottom, pull the switch up by air vibration. To reduce the sound, open
briefly. the driver’s or front passenger’s window, or
narrow the rear window opening.
2-16
60MK1-82E
BEFORE DRIVING
Mirrors To adjust the mirror, set the selector tab (1) Outside Rearview Mirrors
to the day position, then move the mirror Adjust the outside rearview mirrors so you
Inside Rearview Mirror up, down or sideways by hand to obtain can just see the side of your vehicle in the
You can adjust the inside rearview mirror the best view. mirrors.
by hand so as to see the rear of your vehi- When driving at night, you can move the
cle in the mirror. selector tab to the night position to reduce WARNING
glare from the headlights of vehicles Be careful when judging the size or
behind you. distance of a vehicle or other object
seen in the side convex mirror. Be
WARNING aware that objects look smaller and
appear farther away than when seen
• Always adjust the mirror with the
in a flat mirror.
selector set to the day position.
68LMT0205 • Only use the night position if it is
necessary to reduce glare from the EXAMPLE
headlights of vehicles behind you.
Be aware that in this position you
may not be able to see some
objects that could be seen in the
(1) day position.
(2) (3) (1) (1)
68LMT0206
(2) (3) (2) (3)
(2) Day driving
(3) Night driving
(4)
(4)
60MK155
2-17
60MK1-82E
BEFORE DRIVING
2) Press the outer part of the switch that Outside Rearview Mirrors Folding Front Seats
corresponds to the direction in which Switch
you wish to move the mirror. Seat Adjustment
3) Return the selector switch to the center EXAMPLE
position to help prevent unintended WARNING
adjustment. (1)
Never attempt to adjust the driver’s
seat or seatback while driving. The
seat or seatback could move unex-
pectedly, causing loss of control.
Make sure that the driver’s seat and
seatback are properly adjusted
before you start driving.
WARNING
60MK157 To avoid excessive seat belt slack,
which reduces the effectiveness of
You can fold the mirrors when you park the the seat belts as a safety device,
vehicle in a narrow space. When the igni- make sure that the seats are adjusted
tion mode is “ACC” or “ON”, push the fold- before the seat belts are fastened.
ing switch (1) to fold and unfold the
mirrors. Make sure the mirrors are com-
pletely unfolded before you start driving.
CAUTION
Moving mirrors can pinch and injure
a hand. Do not allow any one’s hand
to get near the mirrors when folding
and unfolding the mirrors.
2-18
60MK1-82E
BEFORE DRIVING
EXAMPLE
EXAMPLE 60MK158
60MK156 If the driver’s seat is equipped with a seat
The adjustment lever for each front seat is height adjuster lever on the outboard side
located under the front of the seat. To of the seat, raise or lower the seat by pull-
adjust the seat position, pull up on the ing up or down the adjuster lever.
adjustment lever and slide the seat forward
or rearward.
After adjustment, try to move the seat for-
ward and rearward to ensure that it is EXAMPLE
securely latched.
60MK159
2-19
60MK1-82E
BEFORE DRIVING
80J001 80JS082
Head restraints are designed to help To raise the front head restraint, pull
reduce the risk of neck injuries in the case upward on the restraint until it clicks. To
of an accident. Adjust the head restraint to lower the restraint, push down on the
the position which places the center of the restraint while holding in the lock lever. If a
head restraint closest to the top of your head restraint must be removed (for clean-
ears. If this is not possible for very tall pas- ing, replacement, etc.), push in the lock
sengers, adjust the head restraint as high lever and pull the head restraint all the way
as possible. out.
WARNING
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
NOTE:
It may be necessary to recline the seat-
back to provide enough overhead clear-
ance to remove the head restraint.
2-20
60MK1-82E
BEFORE DRIVING
EXAMPLE
60MH014 60MH016
2-21
60MK1-82E
BEFORE DRIVING
WARNING
• Never drive the vehicle with the
head restraints removed.
• Do not attempt to adjust the head
restraint while driving.
NOTE:
EXAMPLE It may be necessary to fold forward the
60MH017 seatback to provide enough overhead
60MH018
clearance to remove the head restraint.
The walk-in type seat can be moved to 3rd row seats
provide easy entry to and exit from the 3rd Adjust the head restraint to the position
row seats. You can move a walk-in seat by
which places the center of the head EXAMPLE
pulling up the lever on the outboard side of restraint closest to the top of your ears. If
the seatback and pushing the seatback this is not possible for very tall passengers,
forward. adjust the head restraint as high as possi-
ble.
WARNING
• After using the walk-in function, be
sure to return the folded seatback
to an upright position.
• Before returning a walk-in seat to
its normal seating position, make
sure that the feet of the passenger
in the 3rd row seat are out of the 60MK052
way.
• After returning the seat to its nor-
mal seating position, make sure it
is securely latched.
2-22
60MK1-82E
BEFORE DRIVING
To raise the rear head restraint, pull Folding Rear Seats 2) Lower the head restraint fully.
upward on the restraint until it clicks. To The rear seat of your vehicle can be folded 3) Store the seat belt buckles in the seat
lower the restraint, push down on the forward to provide additional cargo space. cushion slit.
restraint while holding in the lock lever. If a
head restraint must be removed (for clean- 2nd row seats EXAMPLE
ing, replacement, etc.), push in the lock
lever and pull the head restraint all the way To fold the 2nd row seat forward:
out. EXAMPLE
When installing a child restraint system,
raise the head restraint to the most upper
position.
60MH060
2-23
60MK1-82E
BEFORE DRIVING
NOTICE WARNING
Store both of the seat belt buckles in If you need to carry cargo in the pas-
the seat cushion slit before folding senger compartment with the 3rd row
seats. This helps prevent being seatback folded forward, be sure to
dropped under the seat cushion. secure the cargo or it may be thrown
about, causing injury. Never pile
cargo higher than the seatback.
EXAMPLE
60MH061
NOTE:
When the seatback is locked in the folded
position, pull up the lever on the outboard
side of the seat to unlatch the seatback.
2-24
60MK1-82E
BEFORE DRIVING
To return the seat to the normal position, Seat Belts and Child Restraint
follow the procedure below.
Systems
EXAMPLE
(1) 65D606
(1)
60MK160
65D231S
WARNING
Raise the seatback until it locks into place.
• Never allow persons to ride in the
WARNING cargo area of a vehicle. In the event
NOTICE of an accident, there is a much
Do not pull the luggage flap (1) or Wear Your Seat Belts at All Times. greater risk of injury for persons
place any luggage when the luggage who are not riding in a seat with
flap is pull toward rear. Otherwise, their seat belt securely fastened.
the luggage flap (1) will be damaged. WARNING • Seat belts should always be
An air bag supplements, or adds to, adjusted as follows:
After returning the seat, try moving the the frontal crash protection offered – the lap portion of the belt should
seatback to make sure they are securely by seat belts. The driver and all pas- be worn low across the pelvis,
latched. sengers must be properly restrained not across the waist.
by wearing seat belts at all times, – the shoulder straps should be
whether or not an air bag is mounted worn on the outside shoulder
at their seating position, to minimize only, and never under the arm.
the risk of severe injury or death in – the shoulder straps should be
the event of a crash. away from your face and neck,
but not falling off your shoulder.
(Continued)
2-25
60MK1-82E
BEFORE DRIVING
WARNING
(Continued)
• Never use the same seat belt on
more than one occupant and never
as low as possible attach a seat belt over an infant or
across the hips child being held on an occupant’s
Across the pelvis lap. Such seat belt use could cause
serious injury in the event of an
accident.
• Periodically inspect seat belt
assemblies for excessive wear and
damage. Seat belts should be
65D201 65D199
replaced if webbing becomes
frayed, contaminated, or damaged
in any way. It is essential to replace
WARNING WARNING the entire seat belt assembly after it
(Continued) (Continued) has been worn in a severe impact,
• Seat belts should never be worn • Pregnant women should use seat even if damage to the assembly is
with the straps twisted and should belts, although specific recommen- not obvious.
be adjusted as tightly as is com- dations about driving should be • Children age 12 and under should
fortable to provide the protection made by the woman’s medical advi- ride properly restrained in the rear
for which they have been designed. sor. Remember that the lap portion seat.
A slack belt will provide less pro- of the belt should be worn as low • Infants and small children should
tection than one which is snug. as possible across the hips, as never be transported unless they
• Make sure that each seat belt shown in the diagram. are properly restrained. Restraint
buckle is inserted into the proper • Do not wear your seat belt over systems for infants and small chil-
buckle catch. It is possible to cross hard or breakable objects in your dren can be purchased locally and
the buckles in the rear seat. pockets or on your clothing. If an should be used. Make sure that the
(Continued) accident occurs, objects such as system you purchase meets appli-
glasses, pens, etc. under the seat cable safety standards. Read and
belt can cause injury. follow all the directions provided
(Continued) by the manufacturer.
(Continued)
2-26
60MK1-82E
BEFORE DRIVING
Lap-Shoulder Belt
WARNING Emergency Locking Retractor (ELR)
(Continued) The seat belt has an emergency locking Low on hips
• For children, if the shoulder belt retractor (ELR), which is designed to lock
irritates the neck or face, move the the seat belt only during a sudden stop or
child closer to the center of the impact. It also may lock if you pull the belt
vehicle. across your body very quickly. If this hap-
• Avoid contamination of seat belt pens, let the belt go back to unlock it, then
webbing by polishes, oils, chemi- pull the belt across your body more slowly.
cals, and particularly battery acid.
Cleaning may safely be carried out Safety reminder
using mild soap and water. Sit up straight and
• Do not insert any items such as fully back
coins, clips, etc. into the seat belt 60A040
buckles, and be careful not to spill
liquids into these parts. If foreign To reduce the risk of sliding under the belt
materials get into a seat belt Low on hips during a collision, position the lap portion
buckle, the seat belt may not work of the belt across your lap as low on your
properly. hips as possible and adjust it to a snug fit
• All seatbacks should always be in by pulling the shoulder portion of the belt
an upright position when driving, upward through the latch plate. The length
or seat belt effectiveness may be of the diagonal shoulder strap adjusts itself
reduced. Seat belts are designed to to allow freedom of movement.
offer maximum protection when
seatbacks are in the upright posi- 60A038
tion.
2-27
60MK1-82E
BEFORE DRIVING
All Seat Belts Except Center of 2nd Center Seat Belt of 2nd Row Seat
Row Seat Lap belt
TO TIGHTEN
Low on hips
60A039
2-28
60MK1-82E
BEFORE DRIVING
60MH022 80J2008
60MK190
To lengthen, release the latch plate from NOTE:
the buckle, pull the latch plate (adjuster) in The word “CENTER” is marked into the
the direction of the arrow. The latch plate buckle for the rear center belt. The buckles
should then be refitted into the buckle and are designed so a latch plate cannot be
the belt tightened as previously described. inserted into the wrong buckle.
2-29
60MK1-82E
BEFORE DRIVING
When the driver does not buckle his or her Shoulder Anchor Height Adjuster Seat Belt Hanger (for 2nd row seats)
seat belt with the ignition mode “ON”, the (if equipped)
driver’s seat belt reminder light in the EXAMPLE
instrument cluster will blink until the EXAMPLE
driver’s seat belt is buckled.
WARNING
It is absolutely essential that the
driver and passengers wear their seat
belts at all times. Persons who are 60MH016
not wearing seat belts have a much 64J198 NOTE:
greater risk of injury if an accident Adjust the shoulder anchor height so that To enter to or exit from the 3rd row seat,
occurs. Make a regular habit of buck- the shoulder belt rides on the center of the hook the webbing of the outboard lap-
ling your seat belt before pressing outboard shoulder. To move upward, slide shoulder belt of 2nd row seat before mov-
the engine switch. the anchor up. To move downward, slide ing the 2nd row seat.
the anchor down while pulling the lock
knob out. After adjustment, make sure that
the anchor is securely locked.
WARNING
Be sure that the shoulder belt is posi-
tioned on the center of the outside
shoulder. The belt should be away
from your face and neck, but not fall-
ing off your shoulder. Misadjustment
of the belt could reduce the effective-
ness of the safety belt in a crash.
2-30
60MK1-82E
BEFORE DRIVING
Periodically inspect the seat belts to make Infant restraint - rear seat only
sure they work properly and are not dam-
aged. Check the webbing, buckles, latch EXAMPLE
plates, retractors, anchorages, and guide
loops. Replace any seat belts which do not
work properly or are damaged.
80JC007
2-31
60MK1-82E
BEFORE DRIVING
80JC008
2-32
60MK1-82E
BEFORE DRIVING
WARNING WARNING
If you install a child restraint system Children could be endangered in a
in the 2nd row seat, slide the seat crash if their child restraint systems
installed the child restraint system as are not properly secured in the vehi-
far back as possible. If you install a cle. When installing a child restraint
child restraint system in the 3rd row system, be sure to follow the instruc-
seat, slide the seat in front of the seat tions below. Be sure to secure the
installed a child restraint system child in the restraint system accord-
enough forward so that the child’s ing to the manufacturer’s instruc-
feet do not contact the front seat- tions.
back. These will help avoid injury to
the child in the event of an accident.
65D608 WARNING
In an accident or sudden stop, the
rear seat armrest could fall forward. If
there is a child in a rear-facing child
restraint in the center seating posi-
tion, the falling armrest could injure
the child. Make sure the armrest is
back in the seat when not in use.
65D609
2-33
60MK1-82E
BEFORE DRIVING
Installation with Lap-Shoulder Seat Installation with a Lap Belt Seat Belt Pretensioner System
Belts EXAMPLE EXAMPLE
and/or
NOTICE
Before installing a child restraint sys-
tem in the rear seat, raise the head
restraint to the most upper position.
60G132 63J269
2-34
60MK1-82E
BEFORE DRIVING
To determine if your vehicle is equipped The pretensioner is located in each front Please note that the pretensioners along
with a seat belt pretensioner system at the seat belt retractor. The pretensioner tight- with the air bags will activate in severe
front seating positions, check the label on ens the seat belt so the belt fits the occu- frontal collisions. They are not designed to
the front seat belt at the bottom part. If the pant’s body more snugly in the event of a activate in rear impacts, side impacts, roll-
letters “p” and/or “PRE” appear as illus- frontal crash. The retractors will remain overs, or minor frontal collisions. The pre-
trated, your vehicle is equipped with the locked after the pretensioners are acti- tensioners can be activated only once. If
seat belt pretensioner system. You can use vated. Upon activation, some noise will the pretensioners are activated (that is, if
the pretensioner seat belts in the same occur and some smoke may be released. the air bags are activated), have the pre-
manner as ordinary seat belts. These conditions are not harmful and do tensioner system serviced by an autho-
Read this section and the “Supplemental not indicate a fire in the vehicle. rized SUZUKI dealer as soon as possible.
Restraint System (air bags)” section to The driver and all passengers must be
If the “AIR BAG” light on the instrument
learn more about the pretensioner system. properly restrained by wearing seat belts
cluster does not blink or come on briefly
at all times, whether or not a pretensioner
The seat belt pretensioner system works is equipped at their seating position, to
when the engine switch is pressed to
with the SUPPLEMENTAL RESTRAINT minimize the risk of severe injury or death
change the ignition mode to “ON”, stays on
SYSTEM (Air Bags). The crash sensors in the event of a crash.
for more than 10 seconds, or comes on
and the electronic controller of the air bag while driving, the pretensioner system or
system also control the seat belt preten- Sit fully back in the seat; sit up straight; do the air bag system may not work properly.
sioners. When the air bags are triggered, not lean forward or sideways. Adjust the Have both systems inspected by an autho-
the pretensioner are also triggered. For belt so the lap portion of the belt is worn rized SUZUKI dealer as soon as possible.
precautions and general information low across the pelvis, not across the waist.
Service on or around the pretensioner sys-
including servicing the pretensioner sys- Please refer to the “Seat Adjustment” sec-
tem components or wiring must be per-
tem, refer to the “Supplemental Restraint tion and the instructions and precautions
formed only by an authorized SUZUKI
System (air bags)” section in addition to about the seat belts in this “Seat Belts and
dealer who is specially trained. Improper
this “Seat Belt Pretensioner System” sec- Child Restraint Systems” section for details
service could result in unintended activa-
tion, and follow all those precautions. on proper seat and seat belt adjustments.
tion of pretensioners or could render the
pretensioner inoperative. Either of these
two conditions may result in personal
injury.
2-35
60MK1-82E
BEFORE DRIVING
2-36
60MK1-82E
BEFORE DRIVING
Supplemental Restraint
System (air bags) EXAMPLE
2
WARNING
This section of the owner’s manual
describes the protection provided by
your SUZUKI’s SUPPLEMENTAL
3
RESTRAINT SYSTEM (air bags).
Please read and follow ALL these
instructions carefully to minimize
your risk of severe injury or death in 5
the event of a collision. 1
60MK112
2-37
60MK1-82E
BEFORE DRIVING
63J030
60MK113
2-38
60MK1-82E
BEFORE DRIVING
Frontal collision range Front air bags will not inflate dents. Remember, since an air bag
deploys only one time during an accident,
seat belts are needed to restrain occu-
pants from further movements during the
accident.
WARNING
An air bag supplements, or adds to,
60G032 65D236 the crash protection offered by seat
Front air bags are designed to inflate in Front air bags will probably not inflate belts. The driver and all passengers
severe frontal collisions. must be properly restrained by wear-
ing seat belts at all times, whether or
not an air bag is mounted at their
seating position, to minimize the risk
of severe injury or death in the event
of a crash.
65D237
2-39
60MK1-82E
BEFORE DRIVING
58MS030
I
WARNING NL
2-40
60MK1-82E
BEFORE DRIVING
How the System Works A seat belt helps keep you in the proper
In a frontal collision, the crash sensors will position for maximum protection when an WARNING
detect rapid deceleration, and if the con- air bag inflates. Adjust your seat as far
troller judges that the deceleration rep- back as possible while still maintaining • The driver should not lean over the
resents a severe frontal crash, the control of the vehicle. Sit fully back in your steering wheel. The front passen-
controller will trigger the inflators. The infla- seat; sit up straight; do not lean over the ger should not rest his or her body
tors inflate the appropriate air bags with steering wheel or dashboard. Please refer against the dashboard, or other-
nitrogen or argon gas. The inflated air to the “Seat Adjustment” section and the wise get too close to the dash-
bags provide a cushion for your head and “Seat Belts and Child Restraint Systems” board. In these situations, the out-
upper body. The air bag inflates and in this section for details on proper seat of-position occupant would be too
deflates so quickly that you may not even and seat belt adjustments. close to an inflating air bag, and
realize that it has activated. The air bag will may suffer severe injury.
neither hinder your view nor make it harder • Do not attach any objects to, or
to exit the vehicle. place any objects over, the steering
wheel or dashboard. Do not place
Air bags must inflate quickly and forcefully any objects between the air bag
in order to reduce the chance of serious or and the driver or front passenger.
fatal injuries. However, an unavoidable These objects may interfere with air
consequence of the quick inflation is that bag operation or may be propelled
the air bag may irritate bare skin, such as by the air bag in the event of a
the facial area against a front air bag. Also, crash. Either of these conditions
upon inflation, a loud noise will occur and may cause severe injury.
some powder and smoke will be released.
These conditions are not harmful and do
not indicate a fire in the vehicle. Be aware,
however, that some air bag components 65D610
may be hot for a while after inflation.
2-41
60MK1-82E
BEFORE DRIVING
Note that even though your vehicle may be Servicing the air bag system Scrapping a vehicle that has an uninflated
moderately damaged in a collision, the col- If the air bags inflate, have the air bags air bag can be hazardous. Ask your dealer,
lision may not have been severe enough to and related components replaced by an body repair shop or scrap yard for help
trigger the air bags to inflate. If your vehicle authorized SUZUKI dealer as soon as pos- with disposal.
sustains ANY front-end or side damage, sible.
have the air bag system inspected by an
If your vehicle ever gets in deep water and
authorized SUZUKI dealer to ensure it is in
the driver’s floor is submerged, the air bag
proper working order.
controller could be damaged. If it does,
Your vehicle is equipped with a diagnostic have the air bag system inspected by the
module which records information about SUZUKI dealer as soon as possible.
the air bag system if the air bags deploy in
Special procedures are required for servic-
a crash. The module records information
ing or replacing an air bag. For that rea-
about overall system status, which sensors
son, only an authorized SUZUKI dealer
activated the deployment.
should be allowed to service or replace
your air bags. Please remind anyone who
services your SUZUKI that it has air bags.
Service on or around air bag components
or wiring must be performed only by an
authorized SUZUKI dealer. Improper ser-
vice could result in unintended air bag
deployment or could render the air bag
inoperative. Either of these two conditions
may result in severe injury.
To prevent damage or unintended inflation
of the air bag system, be sure the battery
is disconnected and the ignition mode has
been “LOCK” (OFF) for at least 90 sec-
onds before performing any electrical ser-
vice work on your SUZUKI. Do not touch
air bag system components or wires. The
wires are wrapped with yellow tape or yel-
low tubing, and the couplers are yellow for
easy identification.
2-42
60MK1-82E
BEFORE DRIVING
Instrument Cluster
1. Speedometer 4. Temperature gauge 7. Indicator selector knob
2. Tachometer 5. Information display 8. Warning and indicator lights
3. Fuel gauge 6. Trip meter selector knob
2 5 1
4 8 6 * 8 * 7 8 3 EXAMPLE
60MK191
* These marks are explanation of the knobs 6 and 7. Refer to “Brightness Control” or “Information Display” in this section for detail of
knobs.
2-43
60MK1-82E
BEFORE DRIVING
Warning and Indicator Lights If the brake system warning light comes on
while you are driving the vehicle, it may WARNING
Brake System Warning Light mean that there is something wrong with
If any of the following conditions
the vehicle’s brake system. If this happens,
you should: occur, you should immediately ask
your SUZUKI dealer to inspect the
1) Pull off the road and stop carefully. brake system.
• If the brake system warning light
WARNING does not go out after the engine
has been started and the parking
Remember that stopping distance brake has been fully released.
65D477
may be longer, you may have to push • If the brake system warning light
Three different types of operations exist harder on the pedal, and the pedal does not come on when the engine
depending on the vehicle’s specification. may go down farther than normal. switch is pressed to change the
1) The light comes on briefly when the ignition mode to “ON”.
engine switch is pressed to change the 2) Test the brakes by carefully starting and • If the brake system warning light
ignition mode to “ON”. stopping on the shoulder of the road. comes on at any time during vehi-
2) The light comes on when the parking – If you determine that it is safe, drive cle operation.
brake is engaged with the ignition mode cautiously at low speed to the nearest
“ON”. dealer for repairs, or NOTE:
3) The light comes on when under either – Have the vehicle towed to the nearest Because the brake system is self-adjust-
or both of above two conditions. dealer for repairs. ing, the fluid level will drop as the brake
The light also comes on when the fluid in pads become worn. Replenishing the
the brake fluid reservoir falls below the brake fluid reservoir is considered normal
specified level. periodic maintenance.
2-44
60MK1-82E
BEFORE DRIVING
Anti-Lock Brake System (ABS) If one of these happens, have the system Oil Pressure Light
Warning Light inspected by your SUZUKI dealer.
If the ABS becomes inoperative, the brake
system will function as an ordinary brake
system that does not have this ABS sys-
tem.
For details of ABS system, refer to “Anti-
Lock Brake System (ABS)” in the “OPER- 50G051
65D529 ATING YOUR VEHICLE” section.
This light comes on when the engine
When the engine switch is pressed to switch is pressed to change the ignition
change the ignition mode to “ON”, the light mode to “ON”, and goes out when the
comes on briefly so you can check that the engine is started. The light will come on
light is working. and remain on if there is insufficient oil
If the light stays on, or comes on when pressure. If the light comes on when driv-
driving, there may be something wrong ing, pull off the road as soon as you can
with the ABS. and stop the engine.
Check the oil level and add oil if necessary.
If this happens: If there is enough oil, the lubrication sys-
1) Pull off the road and stop carefully. tem should be inspected by your SUZUKI
2) Change the ignition mode to “LOCK” dealer before you drive the vehicle again.
(OFF) by pressing the engine switch
and then start the engine again.
NOTICE
If the warning light comes on briefly then
• If you operate the engine with this
turns off, the system is normal. If the warn-
light on, severe engine damage can
ing light still stays on, the system will be
result.
something wrong.
• Do not rely on the oil pressure light
If the light and the brake system warning to indicate the need to add oil. Be
light stay on, or come on simultaneously sure to periodically check the
when driving, your ABS system is engine oil level.
equipped with the rear brake force control
function (proportioning valve function) and
there may be something wrong with both
the rear brake force control function and
anti-lock function of the ABS system.
2-45
60MK1-82E
BEFORE DRIVING
This light comes on when the engine This light blinks or comes on for several Your vehicle has a computer-controlled
switch is pressed to change the ignition seconds when the engine switch is emission control system. A malfunction
mode to “ON”, and goes out when the pressed to change the ignition mode to indicator light is provided on the instrument
engine is started. The light will come on “ON” so you can check if the light is work- panel to indicate when it is necessary to
and remain on if there is something wrong ing. have the emission control system serviced.
with the battery charging system. If the The malfunction indicator light comes on
The light will come on and stay on if there
light comes on when the engine is running, when the engine switch is pressed to
is a problem in the air bag system or the
the charging system should be inspected change the ignition mode to “ON” to let you
seat belt pretensioner system.
immediately by your SUZUKI dealer. know the light is working and goes out
when the engine is started.
Driver’s Seat Belt Reminder Light WARNING
If the malfunction indicator light comes on
If the “AIR BAG” light does not blink or blinks when the engine is running, there
or come on briefly when the engine is a damage in the emission control sys-
switch is pressed to change the igni- tem.
tion mode to “ON”, stays on for more Bring the vehicle to your SUZUKI dealer to
than 10 seconds, or comes on while have the damage fixed.
driving, the air bag system or the
seat belt pretensioner system may (For EU specification vehicle)
60G049 Also, if this light comes on when the
not work properly. Have both sys-
If the driver’s seat belt is unbuckled when tems inspected by an authorized engine is running, there is the problem with
the engine switch is pressed to change the SUZUKI dealer. the automatic transaxle system. Ask your
ignition mode to “ON”, this light will blink SUZUKI dealer to have the system
until the driver’s seat belt is buckled. inspected.
For details about the seat belt reminder,
refer to “Seat Belts and Child Restraint
Systems” in this section.
2-46
60MK1-82E
BEFORE DRIVING
2-47
60MK1-82E
BEFORE DRIVING
Electric Power Steering Light However, repeating these operations could Turn Signal Indicators
cause the power steering system dam-
aged.
NOTE:
If the power steering system does not work
properly, you will feel heavier to steer but
you still will be able to steer.
79J039 50G055
This light comes on when the engine NOTE: When you turn on the left or right turn sig-
switch is pressed to change the ignition If the steering is operated, you may hear a nals, the corresponding green arrow on the
mode to “ON”, and goes out when the noise. This is normal and indicates that the instrument panel will blink along with the
engine is started. power steering system works properly. respective turn signal lights. When you
turn on the hazard warning switch, both
If this light comes on while driving, the arrows will blink along with all of the turn
power steering system may not work prop- signal lights.
erly. Have the system inspected by your
SUZUKI dealer.
Main Beam (high beam) Indicator
NOTE: Light
Following operations of the steering wheel
while parking or driving at a very low-
speed may have steering effort bigger
gradually. This is not a malfunction of the
steering system, but the power steering
control system limits the power assist in
order to prevent them from overheating. 50G056
• The steering wheel is operated very
often. This indicator comes on when headlight
• The steering wheel is kept in a fully main beams (high beams) are turned on.
turned position for a long while.
When the power steering control system
cool down, the power steering system
back to the original condition.
2-48
60MK1-82E
BEFORE DRIVING
82K097
82K098
2-49
60MK1-82E
BEFORE DRIVING
Tachometer Fuel Gauge When the low fuel warning light (1) comes
on, a ding sounds once to remind you to fill
the fuel.
EXAMPLE If you do not fill the fuel, a ding sounds
every time when the engine switch is
pressed to change the ignition mode to
“ON”.
NOTE:
The activation point of the low fuel warning
light (1) varies depending on road condi-
tions (for example, slope or curve) and
(2) driving conditions because of fuel moving
in the tank.
(1)
EXAMPLE
68LM224 74LHT0220
The mark (2) indicates that the fuel filler
door is located on the left side of the vehi-
The tachometer indicates engine speed in When the ignition mode is “ON”, this cle.
revolutions per minute. gauge gives an approximate indication of
the amount of fuel in the fuel tank. “F”
NOTICE stands for full and “E” stands for empty.
Never drive the vehicle with the If the indicator gets off the graduation of
engine revving in the red zone or “E” (not character “E”), refill the tank as
severe engine damage can result. soon as possible.
Keep the engine speed below the red
zone even when downshifting to a NOTE:
lower gear position. The indicator moves a little depending on
Refer to “Downshifting maximum road conditions (for example, slope or
allowable speeds” in the “OPERAT- curve) and driving conditions because of
ING YOUR VEHICLE” section. fuel moving in the tank.
2-50
60MK1-82E
BEFORE DRIVING
(Initial setting)
2-51
60MK1-82E
BEFORE DRIVING
NOTE: Information Display When the ignition mode is “ON”, the infor-
• If you do not turn the brightness control mation display shows the following infor-
knob within several seconds of activat- mation.
ing the brightness control display, the EXAMPLE
Display (A)
brightness control display will be can- (A)
Thermometer
celed automatically. (B)
• When you reconnect the battery, the (C) Display (B)
brightness of the instrument panel lights (D) Transaxle selector position indicator
will be reinitialized. Readjust the bright- (E)
ness according to your preference. Display (C)
Trip meter / Instantaneous fuel consump-
tion / Average fuel consumption / Driving
range
Display (D)
Odometer
(1) (3) (2)
Display (E)
60MK181 Clock
(1) Trip meter selector knob
(2) Indicator selector knob
(3) Information display
2-52
60MK1-82E
BEFORE DRIVING
Thermometer When the display (C) shows the driving Transaxle selector position indicator
When the ignition mode is “ON”, the dis- range, you can change the unit of tem-
play (A) shows the thermometer. perature. EXAMPLE (b)
The thermometer indicates the outside To change the unit of temperature, while
temperature. pushing and holding the trip meter selector
knob (1), turn the indicator selector knob
EXAMPLE (2).
(a )
EXAMPLE 68LM260
2-53
60MK1-82E
BEFORE DRIVING
Trip meter
EXAMPLE Push the trip meter selector The trip meter can be used to measure the
knob (1). distance traveled on short trips or between
fuel stops.
Push the indicator selector You can use the trip meter A or trip meter B
(c)
knob (2). independently.
(c) Trip meter A To reset the trip meter to zero, push and
(d) Trip meter B hold the trip meter selector knob (1) for a
(e) Instantaneous fuel consumption while when the display shows the trip
(f) Average fuel consumption meter.
(d) (g) Driving range
NOTE:
WARNING The indicated maximum value of the trip
meter is 9999.9. When you run past the
If you attempt to adjust the display maximum value, the indicated value will
while driving, you could lose control return to 0.0.
(e) of the vehicle.
Do not attempt to adjust the display
while driving.
NOTE:
(f) • Indications will change when you push
and release a knob.
• The display shows estimated values.
Indications may not be the same as
actual values.
(g)
71LMT0204
2-54
60MK1-82E
BEFORE DRIVING
Instantaneous Fuel Consumption Average fuel consumption To change the unit of average fuel con-
The display shows the value of instanta- If you selected average fuel consumption sumption, while pushing and holding the
neous fuel consumption only when the the last time you drove the vehicle, the dis- trip meter selector knob (1), turn the indica-
vehicle is moving. play shows the last value of average fuel tor selector knob (2).
consumption from previous driving when
NOTE: the engine switch is pressed to change the EXAMPLE
• The display does not show the value ignition mode to “ON”. Unless you reset
unless the vehicle is moving. the value of average fuel consumption, the
• The indicated maximum value of instan- display indicates the value of average fuel
(Initial
taneous fuel consumption is 30. No consumption which includes average fuel setting)
more than 30 will be indicated on the dis- consumption during previous driving.
play even if the actual instantaneous fuel
To reset the average fuel consumption to
consumption is higher.
zero, push and hold the indicator selector
• The display shows estimated values.
knob (2) for a while when the display
Indications may not be the same as
shows the average fuel consumption.
actual values.
• You can change the units that instanta-
NOTE:
neous fuel consumption is displayed in.
When you reset the indication or reconnect
Refer to “Average fuel consumption” in
the negative (–) terminal to the battery, the
this section.
value of average fuel consumption will be
shown after driving for a while.
68LM262
NOTE:
• When you change the units that average
fuel consumption is displayed in, the
instantaneous fuel consumption units will
be changed automatically.
• When you reconnect the negative (–)
terminal to the battery, the unit of the
average fuel consumption will be reini-
tialized. Change the unit again to your
preference.
2-55
60MK1-82E
BEFORE DRIVING
2-56
60MK1-82E
BEFORE DRIVING
Setting Mode
In the setting mode, you can set up the following functions.
Indication Functions
Central door locking system “ ”
Security system “ ”
Initialization setting “ ”
NOTE:
Turn the indicator selector knob Depending on vehicle’s specifications,
(2). some items may not be displayed.
2-57
60MK1-82E
BEFORE DRIVING
How to operate the setting mode: Door locking and unlocking Initialization setting “ ”
1) When the ignition mode is “ON” and the buzzer “ ” • : Initialize all settings
vehicle is stationary, push the trip meter • : Buzzer sounds when the
selector knob (1) to switch the informa- doors (including the tailgate) EXAMPLE
tion display indication (C) to the trip are locked or unlocked by
meter. using the keyless push start
2) Push and hold the indicator selector system remote controller or
knob (2) until the display shows “ ”. request switch (default set-
3) Turn and/or push the indicator selector ting)
knob (2) to select a function that you • : Buzzer does not sound when 60MS113
want to set up according to the above the doors (including the tail-
chart. gate) are locked or unlocked NOTE:
4) Turn and/or push the indicator selector by using the keyless push • As shown in the above illustration,
knob (2) to register settings of the fol- start system remote controller “ ” indicates on the display of cur-
lowing functions. or request switch rently setting item.
• To go back to the higher level display
Central door locking system “ ” Additional flashes during operation, turn the indicator
• : Unlock all doors by turning the of the turn signal “ ” selector knob (2) to display “ ” or
key, pushing the keyless push • : Turn signal flashes three “ ” and then push the indicator
start system remote controller times after the turn signal selector knob (2).
or request switch once lever is returned
• : Unlock all doors by turning the (default setting) 5) To exit the setting mode, switch the dis-
key, pushing the keyless push • : Disable the additional flashes play to show “ ” and then push the
start system remote controller of turn signal indicator selector knob (2).
or request switch twice
(default setting) Security system “ ”
• : Enable the security system
(default setting)
• : Disable the security system
2-58
60MK1-82E
BEFORE DRIVING
(3)
(2)
(1)
60MK117
60MK116
60MK115 With the headlights on, push the lever for-
To turn the lights on or off, twist the knob ward to switch to the high beams (main
on the end of the lever. There are three beams) or pull the lever toward you to
WARNING positions: switch to the low beams. When the high
To avoid possible injury, do not oper- beams (main beams) are on, a light on the
ate controls by reaching through the OFF (1) instrument panel will come on. To momen-
steering wheel. All lights are off. tarily activate the high beams (main
beams) as a passing signal, pull the lever
(2) slightly toward you and release it when you
Front position lights, tail lights, license have completed the signal.
plate light and instrument lights are on, but
headlights are off.
(3)
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
2-59
60MK1-82E
BEFORE DRIVING
Light Reminder Buzzer Front Fog Light Switch Turn Signal Control Lever
A buzzer sounds to remind you to turn off
the lights if they are left on when the
engine switch is pressed to change the
ignition mode to “LOCK” (OFF) and the
driver’s door is opened.
64J058 60MK115
2-60
60MK1-82E
BEFORE DRIVING
EXAMPLE
60MK142
NOTE:
You can customize the setting for the num-
ber of times of flashing of the turn signal
and its indicator (1 to 4 times). Please ask
an authorized SUZUKI dealer for the cus-
tomization.
2-61
60MK1-82E
BEFORE DRIVING
Windshield Wiper and Washer Wiper and Washer Operation Windshield Washer
When the ignition mode is “ON”, you can
Lever use the wiper/washer lever or switch.
Windshield Wipers
EXAMPLE
60MK200
2-62
60MK1-82E
BEFORE DRIVING
2-63
60MK1-82E
BEFORE DRIVING
60MK123 68LM240
(1) LOCK Press the horn button of the steering wheel
(2) UNLOCK to sound the horn. The horn will sound with
any ignition mode.
The lock lever is located under the steering
column. To adjust the steering wheel
height:
1) Push down the lock lever to unlock the
steering column.
2) Adjust the steering wheel to the desired
height and lock the steering column by
pulling up the lock lever.
3) Try moving the steering wheel up and
down to make sure it is securely locked
in position.
2-64
60MK1-82E
BEFORE DRIVING
(1)
60MK192
NOTICE
The heated rear window uses a large
amount of electricity. Be sure to turn
off after the window has become
clear.
2-65
60MK1-82E
OPERATING YOUR VEHICLE
60G408
60MK1-82E
OPERATING YOUR VEHICLE
WARNING blower is at high speed with the air 1) Make sure that windows, mirrors, lights
intake selector set to “FRESH AIR”. and reflectors are clean and unob-
Avoid breathing exhaust gases. • To allow proper operation of your structed.
Exhaust gases contain carbon mon- vehicle’s ventilation system, keep 2) Visually check the tires for the following
oxide, a potentially lethal gas that is the air inlet grille in front of the points:
colorless and odorless. Since carbon windshield clear of snow, leaves or – the depth of the tread groove
monoxide is difficult to detect by other obstructions at all times. – abnormal wear, cracks and damage
itself, be sure to take the following • Keep the exhaust tailpipe area clear – loose wheel nuts
precautions to help prevent carbon of snow and other material to help – existence of foreign material such as
monoxide from entering your vehicle. reduce the buildup of exhaust nails, stones, etc.
• Do not leave the engine running in gases under the vehicle. This is Refer to “Tires” in “INSPECTION AND
garages or other confined areas. particularly important when parked MAINTENANCE” section for details.
(Continued) in blizzard conditions. 3) Look for fluid and oil leaks.
• Have the exhaust system inspected
periodically for damage and leaks. NOTE:
Any damage or leaks should be It is normal for water to drip from the air
repaired immediately. conditioning system after use.
3-1
60MK1-82E
OPERATING YOUR VEHICLE
4) Make sure the hood is fully closed and “CHASSIS AND BODY” in the “Periodic Engine Oil Consumption
latched. Maintenance Schedule” in the
It is normal for the engine to consume
5) Check the headlights, turn signal lights, “INSPECTION AND MAINTENANCE”
some engine oil during normal vehicle
brake lights and horn for proper opera- section for lubrication schedule.
operation.
tion.
6) Adjust the seat and head restraint. WARNING The amount of engine oil consumed
7) Check the brake pedal and the parking depends on the viscosity of the oil, the
brake lever. Make sure the hood is fully closed quality of the oil and the conditions the
8) Adjust the mirrors. and latched before driving. If it is not, vehicle is driven under.
9) Make sure that you and all passengers it can fly up unexpectedly during More oil is consumed during high-speed
have properly fastened your seat belts. driving, obstructing your view and driving and when there is frequent acceler-
10)Make sure that all warning lights come resulting in an accident. ation and deceleration. Under high loads,
on as the engine switch is pressed to your engine also will consume more oil.
change the ignition mode to “ON”. Once a month, or each time you fill your A new engine also consumes more oil,
11)Check all gauges. fuel tank, check the tire pressure using a since its pistons, piston rings and cylinder
12)Make sure that the BRAKE SYSTEM tire pressure gauge. Also check the tire walls have not yet become conditioned.
WARNING light turns off when the park- pressure of the spare tire. New engines reach the normal level of oil
ing brake is released. consumption only after approximately
5000 km (3000 miles) driving.
Once a week, or each time you fill your fuel
tank, perform the following under-hood Oil consumption:
checks: Max. 1.0 L per 1000 km
(1 Qt. per 600 miles)
1) Engine oil level
2) Coolant level When judging the amount of oil consump-
3) Brake fluid level tion, note that the oil may become diluted
4) Battery solution level and make it difficult to accurately judge the
5) Windshield washer fluid level true oil level.
6) Hood latch operation As an example, if a vehicle is used for
Pull the hood release handle inside the repeated short trips, and consumes a nor-
vehicle. Make sure that you cannot mal amount of oil, the dipstick may not
open the hood all the way without show any drop in the oil level at all, even
releasing the secondary latch. Be sure after 1000 km (600 miles) or more of driv-
to close the hood securely after check- ing. This is because the oil is gradually
ing for proper latch operation. See the becoming diluted with fuel or moisture,
item “All latches, hinges and locks” of
3-2
60MK1-82E
OPERATING YOUR VEHICLE
making it appear that the oil level has not Engine Switch ON
changed. • With the engine off
You should also be aware that the diluting You can use such electric equipment as
ingredients evaporate out when the vehicle EXAMPLE the power windows and wipers with the
is subsequently driven at high speeds, engine off. When this ignition mode is
such as on an expressway, making it selected by pressing the engine switch,
appear that oil is excessively consumed the information display in the instrument
after high-speed driving. cluster will come on.
• With the engine on
All electric equipment is operational. The
vehicle can be driven when you have
selected this ignition mode by pressing
the engine switch.
START
61MM0B001 Provided you have the keyless push start
LOCK (OFF) system remote controller with you, the
This mode is for parking the vehicle. When engine automatically starts when you
this mode is selected by pressing the press the engine switch to select this igni-
engine switch and then any door (including tion mode after placing the gearshift lever
the tailgate) is opened or closed, the steer- in the “P” position and depressing the
ing will be locked automatically. brake pedal. (If you need to re-start the
engine while the vehicle is moving, shift
ACC into “N”.)
Press the engine switch to select this igni-
tion mode to use such electric equipment NOTE:
as the audio system, outside rearview mir- You do not need to keep the engine switch
rors and accessory socket with the engine pressed to start the engine.
off. When this position is selected, the
“ACC” indicator light in the instrument clus-
ter comes on. Refer to “Warning and Indi-
cator Lights” in the “BEFORE DRIVING”
section for details.
3-3
60MK1-82E
OPERATING YOUR VEHICLE
3-4
60MK1-82E
OPERATING YOUR VEHICLE
Selection of Ignition Modes Every time you press the engine switch,
Press the engine switch to select the the ignition mode changes as follows.
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running Gearshift
the engine. lever in P
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat. LOCK ACC ON
2) Without depressing the brake pedal, (OFF) (Audio equipment)
press the engine switch (1).
Gearshift lever in a
position other than P
82K253
NOTE:
57L31006
To save the battery, the illumination will be
automatically turned off when both of the NOTE:
following conditions are simultaneously If the gearshift lever is in any position other
met: than “P”, or if the knob button is pushed
• The headlights and position lights are when the gearshift lever is in “P” position
turned off. the ignition mode cannot be returned to
• A period of 15 minutes has elapsed after (1) “LOCK” (OFF).
opening the driver’s door.
If the “PUSH” indicator light blinks and
the ignition modes cannot be selected
82K254 Your keyless push start system remote con-
troller may not be sensed as being within the
“interior workable area” (refer to the related
explanation in this section). Try again after
making sure you have the remote controller
with you. If the ignition modes still cannot be
selected, the battery of the remote controller
may be discharged. To be able to select an
ignition mode, you must then use the follow-
ing method:
3-5
60MK1-82E
OPERATING YOUR VEHICLE
3-6
60MK1-82E
OPERATING YOUR VEHICLE
3-7
60MK1-82E
OPERATING YOUR VEHICLE
WARNING WARNING
• Never drive your vehicle with the When parking the vehicle in
parking brake on: rear brake effec- extremely cold weather, the following
54G039
tiveness can be reduced from over- procedure should be used:
(1) To set heating, brake life may be 1) Set the parking brake.
(2) To release shortened, or permanent brake 2) Shift into “P” (Park) and turn off
(3) To release damage may result. the engine.
• If the parking brake does not hold 3) Get out of the vehicle and put
The parking brake lever is located between the vehicle securely or does not chocks under the wheels.
the seats. To set the parking brake, hold fully release, have your vehicle 4) Release the parking brake.
the brake pedal down and pull the parking inspected immediately by an autho- When you return to your vehicle,
brake lever all the way up. To release the rized SUZUKI dealer. you must remember to first set the
parking brake, hold the brake pedal down, parking brake, then remove the
pull up slightly on the parking brake lever, wheel chocks.
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
3-8
60MK1-82E
OPERATING YOUR VEHICLE
WARNING
(2)
If brake squeal is excessive and
occurs each time the brakes are
applied, you should have the brakes
60MK161 checked by your SUZUKI dealer.
WARNING
Do not “ride” the brakes by applying
them continuously or resting your
foot on the pedal. This will result in
overheating of the brakes which
could cause unpredictable braking
action, longer stopping distances, or
permanent brake damage.
3-9
60MK1-82E
OPERATING YOUR VEHICLE
3-10
60MK1-82E
OPERATING YOUR VEHICLE
Stopping the Engine Starting a Cold and Warm Engine If the “PUSH” indicator light blinks and
• Depress the engine switch to stop the With your foot off the accelerator pedal, the engine cannot be started
engine after the vehicle stopped com- crank the engine by pressing the engine Your keyless push start system remote
pletely. switch to change the ignition mode to controller may not be sensed as being
• In case of emergency, you can stop the “START”. within the “interior workable area”. Try
engine by quickly pushing the engine again after making sure that you have the
switch more than 3 times, or pushing NOTICE remote controller with you. If the engine
and holding the engine switch more than still cannot be started, the battery of the
2 seconds while the vehicle in motion. Do not crank the engine for more remote controller may be discharged. You
than 12 seconds at a time. must then use the following method to be
NOTE: If the engine doesn’t start on the first able to start the engine.
Except in emergency, do not stop the try, wait about 15 seconds before try-
engine while the vehicle in motion. ing again.
EXAMPLE
The steering and braking operation will
require more efforts when the engine After pressing the engine switch to change (1)
stopped. the ignition mode to “START”, the starter
Refer to “Braking” in this section. cranks the engine for about 12 seconds
before it can start the engine. If the engine
NOTICE fails to start at the first attempt, wait about
15 seconds, then try again while keeping
If you stop the engine while the vehi- the engine switch pressed while pressing
cle is in motion, the automatic tran- down the accelerator pedal to 1/3 of its (2)
saxle may be damaged. travel. Release the accelerator pedal when
Avoid stopping the engine while driv- the engine starts.
ing.
If the engine still does not start, try holding
58MST0302
the accelerator pedal all the way to the
• If the engine has been stopped and
floor while cranking. This should clear the 1) Make sure the parking brake is set fully.
stayed as it as for while after the engine
engine if it is flooded. 2) If the gearshift lever is not in the “P”
was stopped unexpectedly or was raced
If you are unable to start the engine using (Park) position, shift it to “P”. Hold the
before stopped, a clicking sound may be
this procedure, consult your SUZUKI brake pedal fully depressed.
heard from around the engine when
dealer. 3) The “PUSH” indicator light in the instru-
engine restarted. This is not a malfunc-
tion. In this case, always let the engine ment cluster will come on. Press the
idle before stop it. engine switch (1).
3-11
60MK1-82E
OPERATING YOUR VEHICLE
4) Within about 10 seconds of blinking of Returning the Ignition Mode to “LOCK” (OFF) mode reminder buzzer
the “PUSH” indicator light in the instru- “LOCK” (OFF) If the driver’s door is opened without
ment cluster, touch the engine switch To ensure safety, the ignition mode can be returning the ignition mode to “LOCK”
with the “LOCK” button end of the returned to “LOCK” (OFF) by pressing the (OFF) by pressing the engine switch, a
remote controller (2) for about 2 sec- engine switch only when the gearshift lever buzzer sounds to warn you of this state.
onds. is placed in the “P” position without press- • If you open the driver’s door after press-
ing the knob button. ing the engine switch to change the igni-
NOTE:
tion mode to “ACC”, the interior buzzer
• If you still cannot start the engine after NOTE: beeps intermittently.
several attempts using the above The engine cannot be returned to the • The buzzer will stop sounding if you then
method, there may be a problem else- “LOCK” (OFF) position if the gearshift lever push the engine switch twice, thus bring-
where, such as a low battery. Contact is in any other position than “P”. ing it back the ignition mode to “LOCK”
your SUZUKI dealer for inspection. Certain problems like a fault in engine sys- (OFF).
• The immobilizer/keyless push start sys- tem may prevent the engine switch from
tem warning light come on for about 5 going back to the “LOCK” (OFF) mode. If NOTE:
seconds while the “PUSH” indicator light this happens, have the vehicle inspected Whenever you leave the vehicle, make
is blinking. by an authorized SUZUKI dealer after sure you have returned the ignition mode
• You may customize the system to cause doing the following: to “LOCK” (OFF) using the engine switch
the interior buzzer to sound once for the • Lock the doors using the key to prevent and then lock the doors. Without returning
“remote controller out of sensing range” theft. (The request switches and the key- the ignition mode to “LOCK” (OFF), you
warning. Please contact an authorized less push start system remote controller cannot use a request switch or keyless
SUZUKI dealer for the customization. cannot be used to lock them.) push start system remote controller to lock
• If the battery of the remote controller is • Disconnect the negative cable from the the doors.
about to be completely discharged, the battery to prevent discharge.
keyless push start system remote con-
Steering lock warning buzzer
troller battery consumption warning light
If the steering lock fails to engage due to a
in the instrument cluster will come on for
fault in the system when the ignition mode
a few seconds when the ignition mode is
is turned to “LOCK” (OFF) by pressing the
changed to “ON” by pressing the engine
engine switch and then any door (including
switch. For details on replacing the bat-
the tailgate) is opened or closed, the inte-
tery, refer to the “Keyless Push Start
rior buzzer will warn you of this condition
System Remote Controller” in the
with repeated short beeps. If this happens,
“BEFORE DRIVING” section.
have the vehicle inspected by an autho-
rized SUZUKI dealer.
3-12
60MK1-82E
OPERATING YOUR VEHICLE
60MK164
3-13
60MK1-82E
OPERATING YOUR VEHICLE
The gearshift lever has a lock mechanism Use the gearshift lever positions as L (Low 1)
to help prevent accidental shifting. To shift described below: Use this position to provide maximum
the gearshift lever: power when climbing steep hills or driving
P (Park) through deep snow or mud, or to provide
Shift with the knob button (1) Use this position to lock the transaxle maximum engine braking when going
pushed in and the brake pedal when the vehicle is parked or when start- down steep hills.
depressed. ing the engine. Shift into Park only when
the vehicle is completely stationary. NOTE:
If you move the gearshift lever to a lower
Shift with the knob button (1) R (Reverse) gear while driving faster than the maximum
pushed in. Use this position to reverse the vehicle allowable speed for the lower gear, the
from stop. Make sure that vehicle is com- transaxle will not actually downshift until
pletely stationary before shifting into your speed drops below the maximum
Shift without the knob button (1) Reverse.
pushed in. speed for the lower gear.
N (Neutral)
Use this position for starting the engine if NOTICE
NOTE: the engine stalls and you need to restart it
• Always shift the gearshift lever without while the vehicle is moving. You may also Be sure to take the following precau-
pushing in the knob button (1) except shift into Neutral and depress the brake tions to help avoid damage to the
when you shift from “P” to “R”, from “D” pedal to hold the vehicle stationary during automatic transaxle:
to “2”, from “2” to “L”, from “N” to “R” or idling. • Make sure that the vehicle is com-
from “R” to “P”. If you always push in the pletely stationary before shifting
knob button (1) when shifting the gear- D (Drive) into “P” or “R”.
shift lever, you could shift into “P”, “R”, Use this position for all normal driving. • Do not shift from “P” or “N” to “R”,
“2”, or “L” by mistake. “D”, “2”, or “L” when the engine is
With the gearshift lever in “D” range you
• If driver’s or passenger’s knee hits the running above idle speed.
can get an automatic downshift by pressing
gearshift lever while driving, the lever • Do not rev the engine with the tran-
the accelerator pedal. The higher the vehi-
could move and the gear could be saxle in a drive position (“R”, “D”,
cle speed is, the more you need to press
changed unexpectedly. “2”, or “L”) and the front wheels
the accelerator pedal to get a downshift.
not moving.
2 (Low 2) • Do not use the accelerator to hold
Use this position to provide extra power the vehicle on a hill. Use the vehi-
when climbing hills, or to provide engine cle’s brakes.
braking when going down hills.
3-14
60MK1-82E
OPERATING YOUR VEHICLE
If You Cannot Shift Automatic Transaxle 5) With pushing the release button by the Parking Sensors
Gearshift Lever Out of “P” (PARK) key or the flat end rod, push the knob
• The parking sensor system uses ultra-
button (2) and shift the gearshift lever to
sonic sensors to detect obstacles near
the desired position.
the rear bumpers. If obstacles are
(2) sensed while you are parking or moving
(1) This procedure is for emergency use only.
the vehicle slowly, the system warns you
If repeated use of this procedure is neces-
by sounding a buzzer.
sary, or the procedure does not work as
• The system emits an ultrasonic wave
described, take the vehicle to your dealer
and the relevant sensor detects the
for repair.
return of the wave reflected by an obsta-
cle. The system measures the time
taken by the ultrasonic wave to reach the
obstacle and return from it, from which it
determines the obstacle’s position.
• The parking sensor function can be used
when the engine switch is pressed to
68LM312
change the ignition mode to “ON”, the
Vehicles with an automatic transaxle have gearshift lever is in the “R” position and
an electrically operated park-lock feature. the parking sensor switch is in the “ON”
If the vehicle’s battery is discharged, or position. This function is helpful in the
there is some other electrical failure, the following cases: pulling over to the curb;
automatic transaxle cannot be shifted out parallel-parking the vehicle; steering the
of Park in the normal way. Jump starting vehicle into a garage; driving along an
may correct the condition. If not, follow the alley; and moving slowly in a place with
procedure described below. This proce- obstacles.
dure will permit shifting the transaxle out of
Park.
1) Be sure the parking brake is firmly
applied.
2) If the engine is running, stop the
engine.
3) Make sure the ignition mode is “ON” or
“ACC”.
4) Remove the cover (1) over the button.
3-15
60MK1-82E
OPERATING YOUR VEHICLE
NOTICE
• Avoid hitting the sensor areas or
directing the nozzle of a high-pres-
sure car washer onto the sensor
areas. Otherwise, the sensors may
be damaged.
• If the bumper hits a hard object, the 60MH126
sensors on it may not work prop-
erly. If this occurs, have the sen- • An obstacle within about 20 cm (8 in)
sors inspected by an authorized from a sensor or just below a sensor is
SUZUKI dealer. not detectable.
• The sensors can detect an obstacle up
to about 1.5 m (5 ft) from the rear of
vehicle.
3-16
60MK1-82E
OPERATING YOUR VEHICLE
NOTE:
WARNING WARNING • Thin poles or obstacles lower than the
sensors may become undetectable as
• Under the following conditions, the (Continued) the vehicle moves closer to them even if
parking sensor system may not – Sensors have intercepted ultra- they have been detected from longer
work normally because the sensors sonic noise from another vehi- distances.
cannot detect obstacles correctly. cle’s horn, engine, air braking • The system may calculate the distance
– Sensors are covered with mud, system (large vehicles), or park- to a road sign or similar obstacle to be
ice or other materials. (Such ing sensor. shorter than the actual distance.
materials must be removed for – Obstacles are too close to the
normal operation.) sensors.
– Sensors are wet from water – Sensors are at an angle to a
How to Use the Parking Sensor
splashes or heavy rain. highly reflective object such as Parking sensor switch
– Sensors are covered by a hand, glass. (Ultrasonic waves are not
sticker, accessory, etc. reflected back from the obstacle.) EXAMPLE
– There is an accessory or other • Sensors may not be able to cor-
object attached within the sen- rectly detect the following types of (2)
sor’s sensing area. obstacles:
– Items such as tow hooks, com- – Objects made of a thin material (1)
mercially available corner poles, like wire netting and ropes
radio antenna, etc. are installed – Square-shaped curbstones or
on the bumper. other objects with sharp edges
– The height of the bumper is – Tall objects with a large upper
changed due to alteration to the part like a road sign
suspension or other causes. – Low-profile objects such as curb-
– The sensor areas are extremely stones
hot from direct sunlight or cold – Sound-absorbing objects such
due to freezing weather. as cotton and snow 61MS403
– The vehicle is on a rough sur- (1) Parking sensor switch
face, slope, gravel road or grass (2) Indicator
field.
– The vehicle is at a steep angle.
(Continued)
3-17
60MK1-82E
OPERATING YOUR VEHICLE
• When the ignition mode is “ON”, and the indicator light in the parking sensor switch is Obstacle Indication by Parking Sen-
on, indicating that the parking sensor is ready for operation under the following condi- sor
tions: Upon detecting an obstacle, the parking
– The gearshift lever is in the “R” position. sensor causes an interior buzzer to sound.
• To deactivate the parking sensor, push the parking sensor switch and make sure the • A buzzer located behind the rear seat
indicator light goes off. sounds when a sensor at the rear
detects an obstacle.
Switch position State • Warnings when obstacles are detected
by corner sensors
EXAMPLE
ON Distance
Buzzer
• When the indicator light is on and all necessary conditions are (approx.)
met, system becomes ready for operation. 45 – 60 cm Short beeps at
(18 – 24 in) short intervals
35 – 45 cm Short beeps at
EXAMPLE (14 – 18 in) very short intervals
OFF Less than
Continuous beep
• The system does not operate. Push the switch to turn off the 35 cm (14 in)
indicator if you do not wish to use the parking sensor.
• Warnings when obstacles are detected
by center sensors
NOTE: Distance
• If you push the parking sensor switch from the OFF to ON position when the ignition Buzzer
(approx.)
mode is “ON”, the inside buzzer sounds.
• When the gearshift lever is shifted to the “R” position with the system ON, a buzzer will 60 – 150 cm Short beeps at
sound once. (24 – 59 in) long intervals
45 – 60 cm Short beeps at
(18 – 24 in) short intervals
35 – 45 cm Short beeps at
(14 – 18 in) very short intervals
Less than
Continuous beep
35 cm (14 in)
3-18
60MK1-82E
OPERATING YOUR VEHICLE
3-19
60MK1-82E
OPERATING YOUR VEHICLE
3-20
60MK1-82E
OPERATING YOUR VEHICLE
3-21
60MK1-82E
DRIVING TIPS
DRIVING TIPS
Running-in ........................................................................... 4-1
Catalytic Converter ............................................................. 4-1
Improving Fuel Economy ................................................... 4-2
Highway Driving .................................................................. 4-3
Driving on Hills .................................................................... 4-3
4
Driving on Slippery Roads ................................................. 4-4
60G409
60MK1-82E
DRIVING TIPS
4-1
60MK1-82E
DRIVING TIPS
4-2
60MK1-82E
DRIVING TIPS
will be greater intake resistance, resulting surface is wet. • When climbing steep hills, the vehicle
in decreased power output and increased • At high speeds, the vehicle may be may begin to slow down and show a lack
fuel consumption. affected by side winds. Therefore, of power. If this happens, you should
reduce speed and be prepared for unex- shift to a lower gear so that the engine
Keep weight to a minimum pected buffeting, which can occur at the will again be operating in its normal
The heavier the load, the more fuel the exits of tunnels, when passing by a cut power range. Shift rapidly to prevent the
vehicle consumes. Take out any luggage of a hill, or when being overtaken by vehicle from losing momentum.
or cargo when it is not necessary. large vehicles, etc. • When driving down a hill, the engine
Keep tire pressures correct should be used for braking by shifting to
Underinflation of the tires can waste fuel next lower gear.
due to increased running resistance of the
tires. Keep your tires inflated to the correct
pressure shown on the label on the driver’s
side door or the driver’s door lock pillar.
4-3
60MK1-82E
DRIVING TIPS
4-4
60MK1-82E
DRIVING TIPS
4-5
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
3
4
3
5
60MK127
5-1
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
(1) (1)
(1)
(2)
68LM502 74LHT0502
Move the knob (1) vertically and the dial Move the knob (1) vertically or horizontally to adjust the direction of airflow as desired.
(2) horizontally, to adjust the direction of
airflow as desired. When “Open”, air CAUTION
comes out from the side outlets regardless
of the airflow selector position. Prolonged exposure to hot air from the heater or air conditioner could result in
low temperature burns. All vehicle occupants, particularly children, the elderly,
those with special needs, individuals with delicate skin, and sleeping individuals,
should maintain sufficient distance from the air outlets to prevent prolonged
exposure to hot airflow.
5-2
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Overhead rear air conditioning system Description of Controls Air flow selector (3)
(1) EXAMPLE (c)
(2)
(b) (d)
(a) (e)
(2)
(1) (4) (5) (3)
To turn on the overhead rear air condition- Temperature selector (1) This is used to select one of the functions
ing system, set the blower speed selector This is used to select the temperature by described below.
of the manual heating and air conditioning turning the selector. Ventilation (a)
system to a position other than “OFF” and
set the rear blower switch (2) to a position Blower speed selector (2)
other than “OFF”. Move the knob (1) verti- This is used to turn on the blower and to
cally or horizontally to adjust the direction select blower speed by turning the selec-
of airflow as desired. tor.
If you need cold air to come out, turn on
the air conditioning switch. Refer to “Air
EXAMPLE
conditioning switch” in this section. 60MK128
During operation of the air conditioner, you Temperature-controlled air comes out of
may notice slight changes in engine the center and side air outlets.
speed. These changes are normal, the
system is designed so that the compressor
turns on or off to maintain the desired tem-
perature. Less operation of the compres-
sor results in better fuel economy.
5-3
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Bi-level (b) Heat & defrost (d) Air intake selector (4)
Temperature-controlled air comes out of Temperature-controlled air comes out of This selector is used to select the following
the floor outlets and cooler air comes out the floor outlets, the windshield defroster modes.
of the center and side outlets. When the outlets, the side defroster outlets and the
temperature selector (1) is in the fully side outlets. Fresh Air (f)
COLD position or fully HOT position, how- When this mode is selected, the indicator
ever, the air from the floor outlets and the Defrost (e) light will go off and outside air is used.
air from the center and side outlets will be
Recirculated Air (g)
the same temperature.
When this mode is selected, the indicator
Heat (c) light will come on, outside air is shut out
and inside air is recirculated. This mode is
suitable when driving through dusty or pol-
EXAMPLE luted air such as in a tunnel, or when
60MK132 attempting to quickly cool down the inte-
Temperature-controlled air comes out of rior.
EXAMPLE the windshield defroster outlets, the side
defroster outlets and the side outlets. “FRESH AIR” and “RECIRCULATED AIR”
60MK130 are switched alternately each time the air
Temperature-controlled air comes out of intake selector is pushed.
the floor outlets and the side outlets, also
comes out of the windshield defroster out- NOTE:
lets and also comes slightly out of the side If you select “RECIRCULATED AIR” for an
defroster outlets. extended period of time, the air in the vehi-
cle can become contaminated. Therefore,
you should occasionally select “FRESH
AIR”.
5-4
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Air conditioning switch (5) System Operating Instructions Head cooled/Feet warmed heating
To turn on the air conditioning system, set Select “BI-LEVEL” and “FRESH AIR”, the
the blower speed selector to a position Natural ventilation temperature selector to the desired tem-
other than “OFF” and push in the “A/C” Select “VENTILATION” and “FRESH AIR”, perature position, and the blower speed
switch. With this “A/C” switch operation, a the temperature selector to the desired selector to the desired blower speed posi-
indicator light will come on when the air temperature position, and the blower tion. Unless the temperature selector is in
conditioning system is on. To turn off the speed selector to “OFF”. Fresh air will flow the fully COLD position or fully HOT posi-
air conditioning system, push the “A/C” through the vehicle during driving. tion, the air that comes out of the center
switch again. Forced ventilation and side outlets will be cooler than the air
The control settings are the same as for that comes out of the floor outlets.
During operation of the air conditioner, you
may notice slight changes in engine natural ventilation except you set the Normal cooling
speed. These changes are normal, the blower speed selector to a position other Set the air flow selector to “VENTILATION”,
system is designed so that the compressor than “OFF”. the temperature selector to the desired
turns on or off to maintain the desired tem- Normal heating (using outside air) temperature position and the blower speed
perature. Select “HEAT” and “FRESH AIR”, the tem- selector to the desired blower speed posi-
perature selector to the desired tempera- tion, and turn on the “A/C” switch. Setting
Less operation of the compressor results
ture position and the blower speed selector the blower speed selector to a higher
in better fuel economy.
to the desired blower speed position. Set- blower speed position increases cooling
ting the blower speed selector to a higher efficiency.
blower speed position increases heating You can switch the air intake selector to
efficiency. either “FRESH AIR” or “RECIRCULATED
Quick heating (using recirculated air) AIR” as you desire. Choosing “RECIRCU-
The control settings are the same as for LATED AIR” increases cooling efficiency.
normal heating except you select “RECIR- Quick cooling (using recirculated air)
CULATED AIR”. If you use this heating The control settings are the same as for
method for an extended period of time, the normal cooling except you select “RECIR-
air in the vehicle can become contami- CULATED AIR” and the highest blower
nated and the windows can become misty. speed.
Therefore, use this method only for quick
heating and change to the normal heating
method as soon as possible.
5-5
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
NOTE: Maintenance
• If you select “RECIRCULATED AIR” for If you do not use the air conditioner for a
an extended period of time, the air in the long period, such as during winter, it may
vehicle can become contaminated. not give the best performance when you
Therefore, you should occasionally start using it again. To help maintain opti-
select “FRESH AIR”. mum performance and durability of your air
• If your vehicle has been left in the sun conditioner, it needs to be run periodically.
with the windows closed, it will cool Operate the air conditioner at least once a
faster if you open the windows briefly month for one minute with the engine
while you operate the air conditioner with idling. This circulates the refrigerant and oil
the air intake selector at “FRESH AIR” and helps protect the internal components.
and the blower at high speed.
If your air conditioner is equipped with air
Dehumidifying EXAMPLE filters, clean or replace them as specified
Set the air flow selector to a desired air 60MK133
in the “Maintenance Schedule” in the
flow selector position, the temperature “INSPECTION AND MAINTENANCE” sec-
NOTE: tion. Have this job done by your SUZUKI
selector to the desired temperature posi- If you need maximum defrosting:
tion and the blower speed selector to the dealer as the lower glove box must be low-
• select “DEFROST” and “FRESH AIR”, ered for this job.
desired blower speed position. Also select • turn on the “A/C” switch,
“FRESH AIR” and turn on the “A/C” switch. • set the blower speed selector to HIGH, NOTE:
• adjust the temperature selector to the Your vehicle uses the air conditioning
NOTE: HOT end, and
Because the air conditioner dehumidifies refrigerant HFC-134a, commonly called
• adjust the side outlets so the air blows “R-134a”. R-134a replaced R-12 around
the air, turning it on will help keep the win- on the side windows.
dows clear, even when blowing heated air 1993 for automotive applications. Other
using the “DEFROST” or “HEAT & refrigerants are available, including recy-
DEFROST” functions. cled R-12, but only R-134a should be used
in your vehicle.
NOTICE
Using the wrong refrigerant may
damage your air conditioning sys-
tem. Use R-134a only. Do not mix or
replace the R-134a with other refrig-
erants.
5-6
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Radio Antenna
EXAMPLE
68KH052
NOTICE
To avoid damage to the radio
antenna:
• Remove the antenna when using an
automatic car wash.
• Remove the antenna when the
antenna hits anything such as a
low ceiling in a parking garage or
putting a car cover over your vehi-
cle.
5-7
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
L SEE
VO K
MUTE
NAVI
BAND
SRC
DVD
GPS DVD
5-8
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Fuel Filler Cap The fuel filler cap is located on the left rear
side of the vehicle. The fuel filler door can EXAMPLE
be unlocked by pulling up the opener lever
EXAMPLE located on the outboard side of the driver’s
seat and locked by simply closing the door.
(1)
Open Close
60MH066
60MK057 NOTE:
If the hook (1) is equipped with the fuel
EXAMPLE filler door, hold the fuel filler cap when refu-
EXAMPLE eling.
57L51093
CAUTION
Remove the fuel filler cap slowly. The
fuel may be under pressure and may
spray out, causing injury.
60MK134
5-9
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Engine Hood
(2) WARNING
If you need to replace the fuel cap, EXAMPLE
use a genuine SUZUKI cap. Use of an
improper cap can result in a malfunc-
tion of the fuel system or emission
(4) control system. It may also result in
fuel leakage in the event of an acci-
dent.
(2) (2)
EXAMPLE (3)
60MH031
NOTE: 60MK135
You can also use the cap holder (2) to hold
To open the engine hood:
the fuel filler cap (3) by hooking the groove
1) Pull the hood release handle located on
(4) when refueling.
the outboard side of the driver’s side of
the instrument panel. This will disen-
To reinstall the fuel filler cap:
gage the engine hood lock halfway.
1) Turn the cap clockwise until you hear
several clicks.
2) Close the fuel filler door.
WARNING
Fuel is extremely flammable. Do not
smoke when refueling, and make
sure there are no open flames or
sparks in the area.
5-10
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
EXAMPLE
60MK168
5-11
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
You can put a card in the card holder (1) on WARNING Rear
the back of the sun visor.
When using the vanity mirror, do not EXAMPLE
move too close to a front air bag
NOTICE location or lean against it. If the front
When you park your vehicle outdoors air bag is accidentally inflated, it
in direct sunlight or in hot weather, could hit you hard. (3) (2) (1)
do not leave plastic cards in the
holder. The heat may distort them.
64J211
5-12
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
60MK061
5-13
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Each socket can be used to provide 12 Universal Serial Bus (USB) Assist Grips
volt/120 watt/10 ampere power for electri-
cal accessories when used alone. Make Socket
sure that the cap remains on the socket
when the socket is not in use. EXAMPLE
NOTICE
• To prevent the fuse from being
blown, when using sockets at the
same time, do not exceed the total
combined power capacity of 12
volt/120 watt/10 ampere.
• Use of inappropriate electrical
accessories can cause damage to
your vehicle’s electrical system.
Make sure that any electrical 54G249
accessories you use are designed 60MK194 Assist grips are provided for convenience.
to plug into this type of socket.
Connect your portable digital music player,
etc. to this socket to enjoy music through NOTICE
the vehicle’s audio system using it as a To avoid damaging the assist grip
source. Refer to “Audio System” in this and the molded headlining, do not
section. hang down the assist grip.
5-14
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
60MH035
5-15
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
EXAMPLE
60MH078
60MK137
60MH037
This pocket is provided for holding light
2nd row seats
and soft things such as gloves, newspa- To use the armrest, pull the strap and
pers or magazines. lower the armrest. When not in use, push
back in the seat until the armrest is
CAUTION secured.
Do not put hard or breakable objects
in the pocket. If an accident occurs,
WARNING
objects such as bottles, cans, etc. In an accident or sudden stop, the
can injure the occupants in the rear rear armrest could fall forward. If
seat. there is a child in a rear-facing child
restraint in the center seating posi-
tion, the falling armrest could injure
the child. Make sure the armrest is
EXAMPLE secured in the stowed position when
60MK062
not in use.
You should hold a bottle with a cap in the
holder.
5-16
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
(1)
EXAMPLE EXAMPLE
60MK196 60MK020
Use the footrest (1) as a support for your To prevent the driver’s side floor mat from
left foot. sliding forward and possibly interfering with
the operation of the pedals, genuine
SUZUKI floor mats are recommended.
Whenever you put the driver’s side floor
mat back in the vehicle after it has been
removed, be sure to hook the floor mat
grommets to the fasteners and position the
floor mat properly in the footwell.
When you replace the floor mats in your
vehicle with a different type such as all-
weather floor mats, we highly recommend
using genuine SUZUKI floor mats for
proper fitting.
5-17
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
Luggage Box
WARNING
Failure to take the following precau-
tions may result in the driver’s side
floor mat interfering with the pedals
and causing a loss of vehicle control (A)
or an accident.
• Make sure that the floor mat grom-
mets are hooked to the fasteners.
• Never place additional floor mats
on top of the existing floor mat.
EXAMPLE
60MH075
60MK063 NOTE:
The luggage box cover can be held open
Pull up the straps (A) of the luggage box
as shown in the above illustration.
cover to use the box.
NOTICE NOTICE
If the luggage box cover is held open
Do not allow items in the box to
while driving, it can be damaged.
extend above the top of the box. Oth-
Do not hold open the luggage box
erwise, the box or cover may be dam-
cover while driving.
aged.
5-18
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
(5)
(2)
(4) (6)
(3)
(1)
60MH10 60MK175
60MH039 The frame hook (3) is provided on the rear The hook (4) is provided for trailer/train/
of the vehicle for use in emergency situa- sea shipping purposes only.
To access the frame hook (1), remove the
tions and trailer/train/sea shipping pur- The hook (5) (or opposite side) is provided
cover (2).
poses only. for trailer/train shipping purposes only. The
hook (6) is provided for sea shipping pur-
The frame hook (1) is provided on the front
of the vehicle for use in emergency situa- NOTICE pose only.
tions and sea shipping purposes only. When you use the frame hook (3),
avoid the driving that gives signifi-
NOTICE cant physical shock on hook. Such
operation can damage the hook, the
When you use the frame hook (1),
vehicle body or the drive system.
avoid the driving that gives signifi-
• Do not accelerate suddenly.
cant physical shock on hook. Such
• Do not tow the vehicle heavier than
operation can damage the hook, or
your vehicle.
the vehicle body.
Do not accelerate suddenly.
To tow your vehicle on the road or high-
way, follow the instruction of “Towing” in
“EMERGENCY SERVICE” section.
5-19
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
WARNING
Do not use the frame hooks to tow
another vehicle or to have your vehi-
cle towed on the road or highway.
The hook (1) is designed for use in
emergency situations such as if your
vehicle or another vehicle gets stuck
in deep mud or snow, and sea ship-
ping only. The hook (3) is designed
for use in emergency situations and
trailer/train/sea shipping only.
The hooks (4) and (5) are provided for
trailer/train shipping purposes only.
The hook (6) is provided for sea ship-
ping purpose only.
NOTICE
Never use the hooks (1) for trailer/
train shipping purposes to prevent
damage to the vehicle.
5-20
60MK1-82E
OTHER CONTROLS AND EQUIPMENT
MEMO
5-21
60MK1-82E
VEHICLE LOADING AND TOWING
54G215
60MK1-82E
VEHICLE LOADING AND TOWING
6-1
60MK1-82E
INSPECTION AND MAINTENANCE
60MK1-82E
INSPECTION AND MAINTENANCE
WARNING WARNING
(Continued) (Continued)
• When the engine is running, keep • Keep used oil, coolant, and other
hands, clothing, tools, and other fluids away from children and pets.
objects away from the fan and drive Dispose of used fluids properly;
belt. Even though the fan may not never pour them on the ground,
60B128S
be moving, it can automatically into sewers, etc.
turn on without warning.
WARNING • When it is necessary to do service
work with the engine running, make
You should take extreme care when sure that the parking brake is set
working on your vehicle to prevent fully and the transaxle is in Park.
accidental injury. Here are a few pre-
cautions that you should be espe- Do not touch ignition wires or other
cially careful to observe: ignition system parts when starting
• To prevent damage or unintended the engine or when the engine is
activation of the air bag system or running, or you could receive an
seat belt pretensioner system, be electric shock.
sure the battery is disconnected and • Be careful not to touch a hot
the ignition mode has been “LOCK” engine, exhaust manifold and
(OFF) for at least 90 seconds before pipes, muffler, radiator and water
performing any electrical service hoses.
work on your SUZUKI. Do not touch • Do not allow smoking, sparks, or
air bag system components, seat flames around fuel or the battery.
belt pretensioner system compo- Flammable fumes are present.
nents or wires. • Do not get under your vehicle if it is
The wires are wrapped with yellow supported only with the portable
tape or yellow tubing, and the cou- jack provided in your vehicle.
plers are yellow for easy identifica- • Be careful not to cause accidental
tion. short circuits between the positive
• Do not leave the engine running in and negative battery terminals.
garages or other confined areas.
(Continued) (Continued)
7-1
60MK1-82E
INSPECTION AND MAINTENANCE
7-2
60MK1-82E
INSPECTION AND MAINTENANCE
• For Item 2-1. “Nickel plugs”, replace every 50,000 km if the local law requires.
NOTE:
“I”: Inspect and if necessary, clean, adjust, lubricate or replace
“R”: Replace or change
*1: Inspect or replace more frequently if necessary.
7-3
60MK1-82E
INSPECTION AND MAINTENANCE
NOTE:
“I”: Inspect and if necessary, clean, adjust, lubricate or replace
“R”: Replace or change
WARNING
The shock absorbers are filled with high pressure gas. Never attempt to disassemble them or throw them into a fire. Avoid
storing them near a heater or heating device. When scrapping the absorber, the gas must be released from the absorber
safely. Ask your dealer for assistance.
7-4
60MK1-82E
INSPECTION AND MAINTENANCE
7-5
60MK1-82E
INSPECTION AND MAINTENANCE
Open Close
52D084
81A147
80G064 Pull out the oil dipstick, wipe oil off with a
clean cloth, insert the dipstick all the way Remove the oil filler cap and pour oil slowly
It is important to keep the engine oil at the through the filler hole to bring the oil level
correct level for proper lubrication of your into the engine, then remove it again. The
oil on the stick should be between the to the upper limit on the dipstick. Be careful
vehicle’s engine. Check the oil level with not to overfill. Too much oil is almost as
the vehicle on a level surface. The oil level upper and lower limits shown on the stick.
If the oil level indication is near the lower bad as too little oil. After refilling, start the
indication may be inaccurate if the vehicle engine and allow it to idle for about a min-
is on a slope. The oil level should be limit, add enough oil to raise the level to
the upper limit. ute. Stop the engine, wait about 5 minutes
checked either before starting the engine and check the oil level again.
or at least 5 minutes after stopping the
engine. NOTICE
The handle of the engine oil dipstick is col-
ored yellow for easy identification. Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
7-6
60MK1-82E
INSPECTION AND MAINTENANCE
7-7
60MK1-82E
INSPECTION AND MAINTENANCE
Replace the Oil Filter Tightening (viewed from filter top) 5) Tighten the filter specified turn from the
1) Using an oil filter wrench, turn the oil fil- point of contact with the mounting sur-
ter counterclockwise and remove it. face (or to the specified torque) using
2) Using a clean rag, wipe off the mount- an oil filter wrench.
ing surface on the engine where the Tightening torque for oil filter
new filter will be seated. 3/4 turn or
3) Smear a little engine oil around the rub- 14 Nm (1.4 kg-m, 10.3 lb-ft)
ber gasket of the new oil filter.
4) Screw on the new filter by hand until the
filter gasket contacts the mounting sur- NOTICE
face. To prevent oil leakage, make sure
that the oil filter is tight, but do not
over-tighten it.
54G093
NOTICE
To tighten the oil filter properly, it is
important to accurately identify the
position at which the filter gasket
first contacts the mounting surface.
54G092
(1) Loosen
(2) Tighten
7-8
60MK1-82E
INSPECTION AND MAINTENANCE
Refill with Oil and Check for Leaks Engine Coolant Failure to use the proper coolant can dam-
1) Pour oil through the filler hole and age your cooling system. Your authorized
install the filler cap. Selection of Coolant SUZUKI dealer can help you select the
For the approximate capacity of the oil, To maintain optimum performance and proper coolant.
refer to the “Capacities” item in the durability of your engine, use SUZUKI
“SPECIFICATIONS” section. Genuine Coolant or equivalent. NOTICE
2) Start the engine and look carefully for
leaks at the oil filter and drain plug. Run To avoid damaging your cooling sys-
This type of coolant is best for your cooling
the engine at various speeds for at least tem:
system as it:
5 minutes. • Always use a high quality ethylene
• Helps maintain proper engine tempera-
3) Stop the engine and wait about 5 min- glycol base non-silicate type cool-
ture.
utes. Check the oil level again and add ant diluted with distilled water at
• Gives proper protection against freezing
oil if necessary. Check for leaks again. the correct mixture concentration.
and boiling.
• Make sure that the proper mix is 50/
• Gives proper protection against corro-
50 coolant to distilled water and in
NOTICE sion and rust.
no case higher than 70/30. Concen-
• When replacing the oil filter, it is trations greater than 70/30 coolant
recommended that you use a genu- to distilled water will cause over-
ine SUZUKI replacement filter. If heating conditions.
you use an aftermarket filter, make • Do not use straight coolant nor
sure it is of equivalent quality and plain water.
follow the manufacturer’s instruc- • Do not add extra inhibitors or addi-
tions. tives. They may not be compatible
• Oil leaks from around the oil filter with your cooling system.
or drain plug indicate incorrect • Do not mix different types of base
installation or gasket damage. If coolants. Doing so may result in
you find any leaks or are not sure accelerated seal wear and/or the
that the filter has been properly possibility of severe overheating
tightened, have the vehicle and extensive engine/automatic
inspected by your SUZUKI dealer. transaxle damage.
7-9
60MK1-82E
INSPECTION AND MAINTENANCE
7-10
60MK1-82E
INSPECTION AND MAINTENANCE
80JM125
7-11
60MK1-82E
INSPECTION AND MAINTENANCE
EXAMPLE Loosen
Correct Wrong
Tighten 0.95 – 1.05mm
(0.037 – 0.041 in.)
7-12
60MK1-82E
INSPECTION AND MAINTENANCE
7-13
60MK1-82E
INSPECTION AND MAINTENANCE
(3) (1)
(2)
(1) (3) (2)
(2)
(1)
54G317
Changing Oil
Since special procedures, materials, and
tools are required to change the automatic
transaxle oil, it is recommended that you
trust this job to your authorized SUZUKI
dealer.
7-14
60MK1-82E
INSPECTION AND MAINTENANCE
WARNING WARNING
Failure to follow the guidelines below Brake fluid is harmful or fatal if swal-
can result in personal injury or seri- lowed, and harmful if it comes in con-
ous damage to the brake system. tact with skin or eyes. If swallowed,
• If the brake fluid in the reservoir do not induce vomiting. Immediately
drops below a certain level, the contact a poison control center or a
brake warning light on the instru- physician. If brake fluid gets in eyes,
ment panel will come on (the flush eyes with water and seek medi-
engine must be running with the cal attention. Wash thoroughly after
parking brake fully disengaged). handling. Solution can be poisonous
Should the light come on, immedi- to animals. Keep out of the reach of
ately ask your SUZUKI dealer to children and animals.
inspect the brake system. 54G108
• A rapid fluid loss indicates a leak in NOTE:
the brake system which should be With disc brakes, the fluid level can be Pedal to floor carpet minimum dis-
inspected by your SUZUKI dealer expected to gradually fall as the brake tance “a”: 59 mm (2.3 in.)
immediately. pads wear.
• Do not use any fluid other than SAE With the engine running, measure the dis-
J1703 or DOT3 brake fluid. Do not tance between the brake pedal and floor
Brake Pedal carpet when the pedal is depressed with
use reclaimed fluid or fluid that has Check if the brake pedal stops at the regu-
been stored in old or open contain- lar height without “spongy” feeling when approximately 30 kg (66 lbs) of force. The
ers. It is essential that foreign parti- you depress it. If not, have the brake sys- minimum distance required is as specified.
cles and other liquids are kept out tem inspected by your SUZUKI dealer. If Since your vehicle’s brake system is self-
of the brake fluid reservoir. you doubt the brake pedal for the regular adjusting, there is no need for pedal
height, check it as follows: adjustment.
If the pedal to floor carpet distance as
CAUTION measured above is less than the minimum
distance required, have your vehicle
Brake fluid can harm your eyes and
inspected by your SUZUKI dealer.
damage painted surfaces. Use cau-
tion when refilling the reservoir.
NOTE:
When measuring the distance between the
brake pedal and floor wall, be sure not to
include the floor mat or rubber on the floor
wall in your measurement.
7-15
60MK1-82E
INSPECTION AND MAINTENANCE
Brake drum
Brake Maximum inner
location diameter
Rear wheels 222 mm (8.74 in.)
60G104S
54G109
If the measured thickness or inner diame-
ter of the most worn part exceeds the
Ratchet tooth specification “b”: value indicated above, the parts should be
WARNING 4th – 9th replaced with a new one. The measure-
If you experience any of the following Lever pull force (1): ment involves disassembling each brake
problems with your vehicle’s brake 200 N (20 kg, 44 lbs) and requires the use of a micrometer or
system, have the vehicle inspected caliper, which must be done according to
immediately by your SUZUKI dealer. Check the parking brake for proper adjust- the instructions described in the relevant
• Poor braking performance ment by counting the number of clicks service manual or available from the rele-
• Uneven braking (brakes not work- made by the ratchet teeth as you slowly vant repair information site.
ing uniformly on all wheels.) pull up on the parking brake lever to the
• Excessive pedal travel point of full engagement. The parking
• Brake dragging brake lever should stop between the speci-
• Excessive noise fied ratchet teeth and the rear wheels
should be securely locked. If the parking
brake is not properly adjusted or the
brakes drag after the lever has been fully
released, have the parking brake inspected
and/or adjusted by your SUZUKI dealer.
7-16
60MK1-82E
INSPECTION AND MAINTENANCE
7-17
60MK1-82E
INSPECTION AND MAINTENANCE
WARNING
54G136
• Your SUZUKI is equipped with tires
(1) Tread wear indicator which are all the same type and
(2) Indicator location mark size. This is important to ensure
proper steering and handling of the
2) Check that the depth of the tread vehicle. Never mix tires of different
groove is more than 1.6 mm (0.06 in.). size or type on the four wheels of
To help you check this, the tires have your vehicle. The size and type of
molded-in tread wear indicators in the tires used should be only those
grooves. When the indicators appear approved by SUZUKI as standard
on the tread surface, the remaining or optional equipment for your
depth of the tread is 1.6 mm (0.06 in.) vehicle.
or less and the tire should be replaced. • Replacing the wheels and tires
3) Check for abnormal wear, cracks and equipped on your vehicle with cer-
damage. Any tires with cracks or other tain combinations of aftermarket
damage should be replaced. If any tires wheels and tires can significantly
show abnormal wear, have them change the steering and handling
inspected by your SUZUKI dealer. characteristics of your vehicle.
• Therefore, use only those wheel
and tire combinations approved by
SUZUKI as standard or optional
equipment for your vehicle.
7-18
60MK1-82E
INSPECTION AND MAINTENANCE
7-19
60MK1-82E
INSPECTION AND MAINTENANCE
51KM038
wise, sulfuric acid could run out and
you might get injury.
Pb (6)
51KM042
7-20
60MK1-82E
INSPECTION AND MAINTENANCE
7-21
60MK1-82E
INSPECTION AND MAINTENANCE
blows, no electrical component will func- and a fire can result. (16) (17) (18) (19) (20) (21) (22)
(39)
tion. If a primary fuse blows, no electrical (23) (24) (25) (26) (27) (28) (29)
(40)
(30) (31) (32) (33) (34) (35) (36)
component in the corresponding load
group will function. When replacing the NOTE:
main fuse, a primary fuse or an individual Make sure that the fuse box always carries
fuse, use a genuine SUZUKI replacement. spare fuses.
To remove a fuse, use the fuse puller pro- 60MK033
vided in the fuse box. The amperage of
each fuse is shown in the back of the fuse
box cover.
7-22
60MK1-82E
INSPECTION AND MAINTENANCE
7-23
60MK1-82E
INSPECTION AND MAINTENANCE
NOTICE 76MH0A139
NOTICE
Frequent replacement of a bulb indi-
cates the need for an inspection of
the electrical system. This should be
carried out by your SUZUKI dealer.
7-24
60MK1-82E
INSPECTION AND MAINTENANCE
Rear Headlight
(2) (3)
(1)
60MH050
67LH084
NOTE:
Pull down the lens by using a flat blade
You can see the position of retaining spring
screwdriver covered with a soft cloth as
(3) from the hole of headlight.
shown. To install it, simply push it back in.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
(3)
60MK037
7-25
60MK1-82E
INSPECTION AND MAINTENANCE
(2)
(2) (1)
(1)
(3)
(2) (4)
(1) (2)
54G124
60MH051
54G123 (3) Removal
(4) Installation
(1) Removal
(2) Installation There are two types of bulb, “Full glass
type” (1) and “Glass/metal type” (2).
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and To remove and install a full glass type bulb
pull it out. To install the holder, push the (1), simply pull out or push in the bulb.
holder in and turn it clockwise. To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.
7-26
60MK1-82E
INSPECTION AND MAINTENANCE
EXAMPLE
(1)
(1)
(2) (2)
80JM071
7-27
60MK1-82E
INSPECTION AND MAINTENANCE
(2)
(1)
60MH054 60MH070
80J100
2) Close the tailgate. Release the claws 3) Remove the each bulb.
To remove a high-mount stop light housing
(3) of the light housing by a flat blade 4) Replace the bulbs.
the following procedure:
screwdriver, etc. The claws are shown To install a high-mounted stop light
1) Open the tailgate, and remove the nuts in the next illustration. Remove a high- housing in the reverse order of removal.
(1) as shown in the illustration. mount stop light housing (2) from the
tailgate.
7-28
60MK1-82E
INSPECTION AND MAINTENANCE
EXAMPLE
70G119
54G129
1) Hold the wiper arm away from the win-
If the wiper blades become brittle or dam-
dow.
aged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the pro-
cedures below.
NOTICE
To avoid scratching or breaking the
window, do not let the wiper arm
strike the window while replacing the
54G130
wiper blade.
2) Squeeze lock (1) towards wiper arm (2)
NOTE: and remove the wiper frame from the
Some wiper blades may be different from arm as shown.
the ones described here depending on 3) Unlock the lock end of the wiper blade
vehicle specifications. If so, consult your and slide the blade out as shown.
SUZUKI dealer for proper replacement
method.
7-29
60MK1-82E
INSPECTION AND MAINTENANCE
EXAMPLE
(3)
(A)
(B)
(3)
60A260 60MH072
(3) (A) Up
EXAMPLE (B) Down
60MH071
NOTE:
When you install the metal retainers (3),
make sure the direction of metal retainers
(3)
as shown in the above illustrations.
(3)
71LMT0708
(3) Retainer
7-30
60MK1-82E
INSPECTION AND MAINTENANCE
(4)
71LMT0707 65D151
80G146
7-31
60MK1-82E
INSPECTION AND MAINTENANCE
54G135
NOTICE
Damage may result if the washer
motor is operated with no fluid in the
washer tank.
7-32
60MK1-82E
INSPECTION AND MAINTENANCE
MEMO
7-33
60MK1-82E
EMERGENCY SERVICE
EMERGENCY SERVICE
Tire Changing Tool ............................................................. 8-1
Jacking Instructions ........................................................... 8-2
Jump Starting Instructions ................................................ 8-6
Towing .................................................................................. 8-7
If the Starter Does Not Operate .......................................... 8-8
If the Engine is Flooded ...................................................... 8-8
If the Engine Overheats ...................................................... 8-8
60G411
60MK1-82E
EMERGENCY SERVICE
Tire Changing Tool The spare tire is stowed under the rear
WARNING floor.
After using the tire changing tools, be To remove the spare tire:
sure to stow them securely or they
can cause injury if an accident
occurs.
CAUTION
The jack should be used only to
change wheels. It is important to read Tighten
the jacking instructions in this sec-
tion before attempting to use the
jack.
Loosen
60MH057
EXAMPLE
The tire changing tools are stowed in the
60MH058
side of the luggage compartment. Remove
the cover to access the tools. 1) Remove the cap and loosen the spare
tire holder hook bolt with the lug
To remove the jack, turn its shaft counter- wrench.
clockwise and pull the jack out of the stor-
age bracket. NOTICE
To stow the jack, place it in the storage Loose the spare tire holder hook bolt
bracket and turn the shaft clockwise until until you can remove the hook by
the jack is securely held in place. yourself. If the bolt is loosen too
much, the hook might off and the
spare tire might drop off to the
ground.
8-1
60MK1-82E
EMERGENCY SERVICE
Jacking Instructions
NOTICE
Tighten the spare tire holder hook
bolt securely. However, do not over-
tighten the bolt, it may be warped or
broken.
60MK066
8-2
60MK1-82E
EMERGENCY SERVICE
63J100
8-3
60MK1-82E
EMERGENCY SERVICE
NOTE:
For more details, please contact an autho-
(1) (4) (6) rized SUZUKI dealer.
(7)
(3) (2)
(3) (2)
60MH132
8-4
60MK1-82E
EMERGENCY SERVICE
WARNING
• Be sure to shift into “P” (Park) EXAMPLE
when you jack up the vehicle. 81A057
• Never jack up the vehicle with the 60MK038
transaxle in “N” (Neutral). Other- Tightening torque for wheel nuts
100 Nm (10.2 kg-m, 73.8 lb-ft) (1) or (2) Flat end tool
wise, unstable jack may cause an
accident. Your vehicle includes two tools, a lug
7) Lower the jack and fully tighten the nuts
in a crisscross fashion with a wrench as wrench and a jack crank, one of which has
4) Remove the wheel nuts and wheel. a flat end.
shown in the illustration.
5) Before installing the new wheel, clean Use the tool with the flat end to remove the
any mud or dirt off from the surface of full wheel cap, as shown above.
the wheel and hub with a clean cloth. WARNING
Clean the hub carefully; it may be hot Use genuine wheel nuts and tighten EXAMPLE
from driving. them to the specified torque as soon
6) Install the new wheel and replace the as possible after changing wheels.
wheel nuts with their cone shaped end Incorrect wheel nuts or improperly
facing the wheel. Tighten each nuts tightened wheel nuts may come
snugly by hand until the wheel is loose or fall off, which can result in
securely seated on the hub. an accident. If you do not have a 60MH074
torque wrench, have the wheel nuts
torque checked by an authorized When installing the cover, make sure that it
SUZUKI dealer. is positioned so that it does not cover or
foul the air valve.
8-5
60MK1-82E
EMERGENCY SERVICE
8-6
60MK1-82E
EMERGENCY SERVICE
Towing
WARNING If you need to have your vehicle towed,
(1) Never connect the jump lead directly contact a professional service. Your dealer
4 to the negative (–) terminal of the dis- can provide you with detailed towing
charged battery, or an explosion may instructions.
1 occur.
NOTICE
CAUTION To help avoid damage to your vehicle
2 during towing, proper equipment and
(3) 3 Connect the jump lead to the engine towing procedures must be used.
mount bracket securely. If the jump
(2) lead disconnects from the engine
EXAMPLE mount bracket because of vibration 2-Wheel Drive (2WD) Automatic
at the start of the engine, the jump Transaxle
71LS30801
lead could be caught in the drive Automatic transaxle vehicles may be
3) Make jump lead connections as follows: belts. towed using either of the following meth-
ods.
1. Connect one end of the first jump
lead to the positive (+) terminal of 4) If the booster battery you are using is 1) From the front, with the front wheels
the flat battery (1). fitted to another vehicle, start the lifted and the rear wheels on the
2. Connect the other end to the positive engine of the vehicle with the booster ground. Before towing, make sure that
(+) terminal of the booster battery battery. Run the engine at moderate the parking brake is released.
(2). speed. 2) From the rear, with the rear wheels
3. Connect one end of the second jump 5) Start the engine of the vehicle with the lifted and a dolly under the front wheels.
lead to the negative (–) terminal of flat battery.
the booster battery (2). 6) Remove the jump leads in the exact NOTICE
4. Make the final connection to an reverse order in which you connected
unpainted, heavy metal part (i.e. Towing your vehicle with the front
them.
engine mount bracket (3)) of the wheels on the ground can result in
engine of the vehicle with the flat damage to the automatic transaxle.
battery (1).
8-7
60MK1-82E
EMERGENCY SERVICE
If the Starter Does Not If the Engine is Flooded If the Engine Overheats
Operate If the engine is flooded with gasoline, it The engine could overheat temporarily
may be hard to start. If this happens, press under severe driving conditions. If the
1) Try pressing the engine switch to
the accelerator pedal all the way to the engine coolant temperature gauge indi-
change the ignition mode to “START”
floor and hold it there while cranking the cates overheating during driving:
with the headlights turned on to deter-
engine.
mine the battery condition. If the head- 1) Turn off the air conditioner, if equipped.
• Do not operate the starter motor for
lights go excessively dim or go off, it 2) Take the vehicle to a safe place and
more than 12 seconds.
usually means that either the battery is park.
flat or the battery terminal contact is 3) Let the engine run at the normal idle
NOTE:
poor. Recharge the battery or correct speed for a few minutes until the indica-
If the engine refuses to start, the starter
battery terminal contact as necessary. tor is within the normal, acceptable tem-
motor automatically stops after a certain
2) If the headlights remain bright, check perature range between “H” and “C”.
period of time. After the starter motor has
the fuses. If the reason for failure of the
automatically stopped or there is anything
starter is not obvious, there may be a WARNING
abnormal in the engine starting system,
major electrical problem. Have the vehi-
the starter motor runs only while the If you see or hear escaping steam,
cle inspected by your authorized
engine switch is held pressed. stop the vehicle in a safe place and
SUZUKI dealer.
immediately turn off the engine to let
it cool. Do not open the hood when
steam is present. When the steam
can no longer be seen or heard, open
the hood to see if the coolant is still
boiling. If it is, you must wait until it
stops boiling before you proceed.
8-8
60MK1-82E
EMERGENCY SERVICE
8-9
60MK1-82E
APPEARANCE CARE
APPEARANCE CARE
Corrosion Prevention ......................................................... 9-1
Vehicle Cleaning ................................................................. 9-2
60G412 9
60MK1-82E
APPEARANCE CARE
Corrosion Prevention vehicle which are not well ventilated to wash off, an additional cleaner may be
permit quick drying. required. Be sure that any cleaner you use
It is important to take good care of your
is not harmful to painted surfaces and is
vehicle to protect it from corrosion. Listed This information illustrates the necessity of
specifically intended for your purposes.
below are instructions for how to maintain keeping your vehicle (particularly the
Follow the manufacturer’s directions when
your vehicle to prevent corrosion. Please underbody) as clean and dry as possible. It
using these special cleaners.
read and follow these instructions carefully. is equally important to repair any damage
to the paint or protective coatings as soon
Repair finish damage
Important Information About Corro- as possible.
Carefully examine your vehicle for damage
sion to the painted surfaces. Should you find
Common causes of corrosion
How to Help Prevent Corrosion any chips or scratches in the paint, touch
1) Accumulation of road salt, dirt, mois- Wash your vehicle frequently them up immediately to prevent corrosion
ture, or chemicals in hard-to-reach The best way to preserve the finish on your from starting. If the chips or scratches have
areas of the vehicle underbody or vehicle and to help avoid corrosion is to gone through to the bare metal, have a
frame. keep it clean with frequent washing. qualified body shop make the repair.
2) Chipping, scratches and any damage to Wash your vehicle at least once during the
treated or painted metal surfaces winter and once immediately after the win- Keep passenger and luggage compart-
resulting from minor accidents or abra- ter. Keep your vehicle, particularly the ments clean
sion by stones and gravel. underside, as clean and dry as possible. Moisture, dirt or mud can accumulate
If you frequently drive on salted roads, under the floor mats and may cause corro-
Environmental conditions which accel- your vehicle should be washed at least sion. Occasionally, check under these
erate corrosion once a month during the winter. If you live mats to ensure that this area is clean and
1) Road salt, dust control chemicals, sea near the ocean, your vehicle should be dry. More frequent checks are necessary if
air or industrial pollution will all acceler- washed at least once a month throughout the vehicle is used off road or in wet
ate the corrosion of metal. the year. weather.
2) High humidity will increase the rate of Certain cargos such as chemicals, fertiliz-
corrosion particularly when the tem- For washing instructions, refer to the “Vehi- ers, cleaners, salts, etc. are extremely cor-
perature range is just above the freez- cle Cleaning” section. rosive by nature. These products should
ing point. be transported in sealed containers. If a
3) Moisture in certain areas of a vehicle Remove foreign material deposits spill or leak does occur, clean and dry the
for an extended period of time may pro- Foreign material such as salts, chemicals, area immediately.
mote corrosion even though other body road oil or tar, tree sap, bird droppings and
sections may be completely dry. industrial fall-out may damage the finish of
4) High temperatures will cause an accel- your vehicle if it is left on painted surfaces.
erated rate of corrosion to parts of the Remove these types of deposits as quickly
as possible. If these deposits are difficult to
9-1
60MK1-82E
APPEARANCE CARE
Store your vehicle in a dry, well-venti- Vehicle Cleaning Cleaning the Interior
lated area
Do not park your vehicle in a damp, poorly Vinyl upholstery
ventilated area. If you often wash your Prepare a solution of soap or mild deter-
vehicle in the garage or if you frequently gent mixed with warm water. Apply the
drive it in when wet, your garage may be solution to the vinyl with a sponge or soft
damp. The high humidity in the garage cloth and let it soak for a few minutes to
may cause or accelerate corrosion. A wet loosen dirt.
vehicle may corrode even in a heated Rub the surface with a clean, damp cloth
garage if the ventilation is poor. to remove dirt and the soap solution. If
some dirt still remains on the surface,
repeat this procedure.
WARNING
Do not apply additional undercoating Fabric upholstery
or rust preventive coating on or Remove loose dirt with a vacuum cleaner.
around exhaust system components Using a mild soap solution, rub stained
such as the catalytic converter, 76G044S areas with a clean damp cloth. To remove
exhaust pipes, etc. A fire could be soap, rub the areas again with a cloth
started if the undercoating substance WARNING dampened with water. Repeat this until the
becomes overheated. stain is removed, or use a commercial fab-
When cleaning the interior or exterior ric cleaner for tougher stains. If you use a
of the vehicle, NEVER USE flammable fabric cleaner, carefully follow the manu-
solvents such as lacquer thinners, facturer’s instructions and precautions.
gasoline, benzene or cleaning materi-
als such as bleaches or strong
household detergents. The materials
could cause personal injury or dam-
age to the vehicle.
9-2
60MK1-82E
APPEARANCE CARE
9-3
60MK1-82E
APPEARANCE CARE
9-4
60MK1-82E
APPEARANCE CARE
NOTICE
If you use an automatic car wash,
make sure that your vehicle’s body
parts, such as spoilers, cannot be
damaged. If you are in doubt, consult
the car wash operator for advice.
60B211S
9-5
60MK1-82E
GENERAL INFORMATION
GENERAL INFORMATION
Vehicle Identification .......................................................... 10-1
84MM01001
10
60MK1-82E
GENERAL INFORMATION
Vehicle Identification The chassis and/or engine serial numbers Engine Serial Number
are used to register the vehicle. They are
Chassis Serial Number also used to assist your dealer when
ordering or referring to special service
EXAMPLE information. Whenever you have occasion
to consult your SUZUKI dealer, remember
to identify your vehicle with this number.
Should you find the number difficult to
read, you will also find it on the identifica-
tion plate.
60G128
74LHT1002
10-1
60MK1-82E
SPECIFICATIONS
SPECIFICATIONS
NOTE:
Specifications are subject to change without notice.
11-1
60MK1-82E
SPECIFICATIONS
ITEM: Engine
Type K14B (DOHC)
Number of cylinders 4
Bore 73.0 mm (2.87 in.)
Stroke 82.0 mm (3.23 in.)
Piston displacement 1373 cm3
(1373 cc, 83.8 cu.in)
Compression ratio 11.0 : 1
ITEM: Electrical
Standard spark plug NGK LKR6F-10
Battery 12V 34B19L
Fuses See “INSPECTION AND MAINTENANCE” section.
11-2
60MK1-82E
SPECIFICATIONS
11-3
60MK1-82E
SPECIFICATIONS
11-4
60MK1-82E
INDEX
12-1
60MK1-82E
INDEX
12-2
60MK1-82E
INDEX
12-3
60MK1-82E
INDEX
Selection of Coolant .............................................................. 7-9 Turn Signal Control Lever ................................................... 2-60
Selection of Ignition Modes .................................................. 3-5 Turn Signal Indicators .........................................................2-48
Shoulder Anchor Height Adjuster...................................... 2-30 Turn Signal Operation .........................................................2-61
Side Door Locks .................................................................... 2-3 U
Spark Plugs .......................................................................... 7-11 Universal Serial Bus (USB) Socket..................................... 5-14
SPECIFICATIONS................................................................. 11-1 Using the Transaxle .............................................................3-13
Specified Fluid ..................................................................... 7-13 V
Specified Oil ........................................................................... 7-5 Vehicle Cleaning .................................................................... 9-2
Speedometer ........................................................................ 2-49 Vehicle Identification ........................................................... 10-1
Starting the Engine.............................................................. 3-10 Vehicle Loading...................................................................... 6-1
Steering ................................................................................ 7-17 W
Sun Visor .............................................................................. 5-11 Walk-in Type Seats (for 2nd row seats) .............................2-21
Supplemental Restraint System (air bags)........................ 2-37 Warning and Indicator Lights ............................................. 2-44
T Warning and Indicator Messages .......................................3-19
Tachometer .......................................................................... 2-50 Washing .................................................................................. 9-4
Tailgate ................................................................................... 2-5 Waxing .................................................................................... 9-5
Temperature Gauge............................................................. 2-51 Windows ............................................................................... 2-15
Theft Deterrent Alarm System ............................................ 2-12 Windshield Washer .............................................................. 2-62
Thermometer........................................................................ 2-53 Windshield Washer Fluid ....................................................7-32
Tilt Steering Lock Lever ...................................................... 2-64 Windshield Wiper and Washer Lever .................................2-62
Tire Chains ............................................................................. 4-4 Windshield Wipers ...............................................................2-62
Tire Changing Tool ................................................................ 8-1 Wiper and Washer Operation..............................................2-62
Tire Inspection ..................................................................... 7-17 Wiper Blades ........................................................................7-29
Tire Rotation......................................................................... 7-19
Tires ...................................................................................... 7-17
To Raise the Vehicle with a Garage Jack ............................ 8-4
Towing .................................................................................... 8-7
Trailer Towing ........................................................................ 6-1
Transaxle selector position indicator ................................ 2-53
Transaxle Warning Light..................................................... 2-47
Trip meter ............................................................................. 2-54
12-4
60MK1-82E
INDEX
MEMO
12-5
60MK1-82E
INDEX
MEMO
12-6
60MK1-82E
BATTERY LABEL SYMBOL MEANINGS
Prepared by
SUZUKI (MYANMAR) MOTOR CO., LTD.
May, 2016
TP234
60MK1-82E