Professional Documents
Culture Documents
Controller Cable
(50 ft w/end plug)
1” Ultrasonic
FlexPipe (15 in.) CableLok
Flow Sensor 24 VAC Transformer Connects head to mainline Secures water-proof
2
(optional) w/ 10’ wire (40VA, indoor) 1” MPT to mainline tee cable connectors
Other Items Needed
(Not supplied by Irrigreen)
6” valve boxes
*One for each Digital Zone 1” Tees with 1” female pipe thread
Protects cable connections PVC or poly
Holds extra sprinkler cable length For connecting Flex-Pipe to mainline
• Important to check flow, some homes have 3/4” pipe inside the home,
which restricts flow to the irrigation system, lessening throw
• Well systems require a constant pressure pump or regulated constant pressure supply, e.g. with
a pressure regulating valve (PRV) set below the lowest pump setting
• Filter required for any water source with particulates (sand, grit, lake water)
500 Micron filter (similar to drip systems)
4
Irrigreen Throw Distances
Verify psi before placing heads
Low flow may affect throws
Total Area
At 60 psi, one Irrigreen head will evenly water any shape within
a 60 foot diameter circle
5
System Design (1 of 2)
One Head per Zone
Place Head to Reach Farthest Corner, 25-35 Feet
Exact placement
not critical as you
can program the Installation hint:
head to the shape Walk in from the
of the zone corner with and
place a flag at 25-
Don’t overlap 30’ for head
sprays or zones placement.
6
System Design (2 of 2)
One Head per Zone
Place head 5 feet or more from the nearest edge*
7
6” Valve box next to each head for
cable connectors and extra cable
Optional
8
Download the IG2 mobile app (raindrop logo)
Follow IOS App Instructions. Scan barcode with App
For Android: connect to Irrigreen Wi-Fi network and enter system password
(Calibration and Auto Water require IOS App)
2 AAA
Clock Backup
(Optional)
10
Connect Digital Sprinklers with Cables
Daisy-chain up to eight sprinklers per cable (#1-8 and #9-16)
11
Irrigreen Connector Direction
Similar to electrical extension cords*
12
Install on all Cable
connections
13
Protect Cable Connections
All connections must be protected by a small valve box
Install next to Digital head below turf
Install box
below turf
14
Eight Sprinklers per Controller Cable
Branch off in two directions with Cable Tees
Helpful Hint:
When flushing the
lines, disconnect
the head and
point Flex-Pipe
out of hole to
keep the hole
from filling with
water
18
Digital Sprinkler Head Depth
Dig 15” hole
Position head so the top of the Digital Sprinkler cap
is about ½” above grade
19
Flush all lines. Twice.
Before, and after, installing heads*
• 1. Before installing any heads, flush
lines to remove all dirt, sand, debris*
2. After all heads are installed, run the
last Digital Sprinkler(s) on the end of
all pipe runs for several minutes to Rocks,
remove all air from the system. sand, etc
caught in
3. Also run all Valve zones to remove ball valve
all air from the system
Trapped / deadhead air anywhere in
the system acts as an “air piston”,
causing calibration errors
• DO Plug all heads together with a all cables before burying to test sprinkler connections
• DO add a second Controller Cable if branching off immediately from the Controller (NOTE: Heads must
be numbered accordingly; e.g. #1-4 on first controller cable and #9-12 on second controller cable)
• DO protect all Digital Sprinkler cable connections with small valve boxes, buried below turf
• DON’T pull IrriGreen Cables with a vibra plow … DO pull 1” conduit for the cables if pulling pipe
• DON’T calibrate and program heads before flushing air from all digital AND valve zone piping
Controller Box May Be Installed Outside
Make sure box location has good Wi-Fi Signal
NOTE: Transformer
must be protected
with outlet box when
installed outside
Tighten glands
around cables
for additional
protection
22
Irrigreen2 Controller Terminals
Wi-Fi
Rain/Soil Antenna
Sensor 1 (install supplied
antenna)
Flow Sensor 1
Digital
Sprinklers 1-8
Digital
Sprinklers 9-16
Master
Valve/Pump
Valve Zones
1-12
23
2 AAA Batteries
Clock Backup
Replace annually
or if App shows
“Battery Voltage”
below 2.1 Volts
(System Setup page)
24
Controller runs hybrid systems with Digital Sprinklers, plus Drip and Spray Zones
25
Master Valve/Pump Wiring
Master Valve Recommended for all Systems
Irrigreen software
relieves mainline
pressure by keeping the
last head valve open for
a few seconds after the
Master Valve closes
26
27
Irrigreen2 Controller Indicator Lights
Green LED is ON, blinks off Blue LED Red LED Flashing:
briefly: System connected to the Flashing: System Error
Home Wi-Fi network System is
Green LED is OFF, blinks on watering
briefly: System is not connected
to any Wi-Fi network
28
Irrigreen2 Controller Buttons
Green RESET Button Blue MODE Button Red SELECT Button
Reset System: Run All Zones : Stop all watering:
Press 1 second Press 3 Seconds to Press 1 Second
run all zones
Skip a Zone:
Press for 1 Second
29
System Status, Manual Watering Control
System status:
Green LED is ON, blinks off briefly: System connected to the Home Wi-Fi network
Green LED is OFF, blinks on briefly: System is not connected to any Wi-Fi network and
broadcasting the Irrigreen Wi-Fi network
Blue LED blinking: System is watering
Watering Controls:
Start Watering Schedule: Press Blue button 3 seconds. All scheduled zones will run
Skip a Zone: Press Blue button 1 second
Stop All Watering: Press Red button 1 second
System Reset:
System Reset: Press Green button 1 second. Will re-connect to Home Wi-Fi in 10 seconds
Direct Connect to Controller: Press Red button 6 seconds, the Irrigreen Wi-Fi Network will
appear. Log in with the password. Press Red button six
seconds to reconnect to the Home Network.
30
Shortened Stream Distances?
Streams Not Evenly Spaced? Calibration failing?
Remove cap as shown and clean the filter
Hand tighten cap back onto riser (NOTE: filter mesh points down)
31
Removing Cap for Servicing Nozzle and Filter
Lift riser up
Grasp riser and remove cap by hand
Tighten torx screw on cap after reassembly
32
Optional Ultrasonic Flow Sensor Installation
24” PVC before and 12” after the flow sensor*
Install Ultrasonic Flow Sensors at 45o
NOTE:
IrriGreen now supplies
pre-cut PVC pipe for flow
sensor installation, use
two sections upstream,
one section downstream
33
Optional Flow Sensor Installation
Waterproof “DBY” connections supplied
Install Flow Sensor and Splices in Valve Box
Ultrasonic
Use DBYs as shown
Flow sensors must Picture shows an
be installed at 45o Impeller flow sensor in
vertical orientation
Use the supplied 3M® DBY “grease cap with wire nut” connectors
Push wire nut all the way into gel cap, ensure wires and wire nut are totally sealed by gel
NOTE: 24” PVC before and 12” after the flow sensor
34
Optional: Flow Sensor Items Needed
(Not supplied by Irrigreen)
Small valve box (6”-10”) 16-18 Gauge two Grease cap/wire nut
For protecting optional flow sensor conductor wire connectors
Connects optional flow sensor Connects flow sensor leads
to the Irrigreen2 Controller to the flow sensor wire
3M® DBY/R, Orbit® 57002 or similar
Irrigreen supplies two with each flow sensor
35
Optional Flow Sensor Wiring to Controller
Red Flow Sensor lead to “Sen1”
Black lead to “Common”
Black Flow
Red Flow Sensor lead to Sensor lead
Controller Terminal“Sen1” to“Common”
36
Per FCC 15.19 (a) (3) and (a) (4): This device complies with part 15
of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may
cause undesired operation.
Per FCC 15.21: The user and installer of the IrriGreen Genius
Irrigation System shall not make any modifications to the system
not expressly approved by IrriGreen. Unauthorized modifications
will void the warranty and void the user's authority to operate the
equipment per FCC rules