Professional Documents
Culture Documents
MODEL G0550/G0551
INSTRUCTION MANUAL
3. KEEP WORK AREA CLEAN. Cluttered 7. NEVER FORCE TOOL. It will do the job
areas and benches invite accidents. better and safer at the rate for which it was
designed.
4. NEVER USE IN DANGEROUS ENVIRON-
MENT. DO NOT use power tools in damp 8. USE RIGHT TOOL. DO NOT force tool or
or wet locations, or where any flammable attachment to do a job for which it was not
or noxious fumes may exist. Keep work designed.
area well lighted.
-2- G0550/G0551 15" Planer
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make 15. USE RECOMMENDED ACCESSORIES.
sure your extension cord is in good condi- Consult the owner’s manual for recom-
tion. Conductor size should be in accor- mended accessories. The use of improper
dance with the chart below. The amperage accessories may cause risk of injury.
rating should be listed on the motor or tool
nameplate. An undersized cord will cause 16. REDUCE THE RISK OF UNINTENTION-
a drop in line voltage resulting in loss of AL STARTING. On machines with magnet-
power and overheating. Your extension ic contact starting switches there is a risk of
cord must also contain a ground wire and starting if the machine is bumped or jarred.
plug pin. Always repair or replace exten- Always disconnect from power source
sion cords if they become damaged. before adjusting or servicing. Make sure
switch is in OFF position before reconnecting.
Minimum Gauge for Extension Cords
LENGTH 17. CHECK DAMAGED PARTS. Before fur-
AMP RATING 25ft 50ft 100ft ther use of the tool, a guard or other part
that is damaged should be carefully
0-6 16 16 16 checked to determine that it will operate
7-10 16 16 14 properly and perform its intended function.
11-12 16 16 14 Check for alignment of moving parts, bind-
13-16 14 12 12 ing of moving parts, breakage of parts,
17-20 12 12 10 mounting, and any other conditions that
21-30 10 10 No may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
10. WEAR PROPER APPAREL. DO NOT
wear loose clothing, gloves, neckties, 18. NEVER LEAVE TOOL RUNNING UNAT-
rings, bracelets, or other jewelry which may TENDED. TURN POWER OFF. DO NOT
get caught in moving parts. Non-slip leave tool until it comes to a complete stop.
footwear is recommended. Wear protective
hair covering to contain long hair. 19. NEVER OPERATE A MACHINE WHEN
TIRED, OR UNDER THE INFLUENCE OF
11. ALWAYS USE SAFETY GLASSES. Also DRUGS OR ALCOHOL. Full mental alert-
use face or dust mask if cutting operation is ness is required at all times when running a
dusty. Everyday eyeglasses only have machine.
impact resistant lenses, they are NOT safe-
ty glasses. 20. NEVER ALLOW UNSUPERVISED OR
UNTRAINED PERSONNEL TO OPER-
12. SECURE WORK. Use clamps or a vise to ATE THE MACHINE. Make sure any
hold work when practical. It’s safer than instructions you give in regards to machine
using your hand and frees both hands to operation are approved, correct, safe, and
operate tool. clearly understood.
13. DO NOT OVER-REACH. Keep proper
21. IF AT ANY TIME YOU ARE EXPERIENC-
footing and balance at all times.
ING DIFFICULTIES performing the intend-
ed operation, stop using the machine! Then
14. MAINTAIN TOOLS WITH CARE. Keep
contact our service department or ask a
tools sharp and clean for best and safest
performance. Follow instructions for lubri- qualified expert how the operation should
cating and changing accessories. be performed.
Like all machines there is danger associated No list of safety guidelines can be complete.
with the Model G0550/G0551. Accidents are Every shop environment is different. Always
frequently caused by lack of familiarity or consider safety first, as it applies to your
failure to pay attention. Use this machine individual working conditions. Use this and
with respect and caution to lessen the pos- other machinery with caution and respect.
sibility of operator injury. If normal safety Failure to do so could result in serious per-
precautions are overlooked or ignored, seri- sonal injury, damage to equipment, or poor
ous personal injury may occur. work results.
Circuit Breaker
Circuit Breaker
G0550 ........................................15 Amp, 2 Pole
G0551 ........................................20 Amp, 2 Pole Figure 1a. NEMA 6-15 plug and receptacle.
Always check to see if the wires in your circuit are 220V Operation
capable of handling the amperage draw from We do not recommend the use of extension cords
your machine, as well as any other machines that on 220V equipment. Instead, arrange the place-
could be operating on the same circuit. If you are ment of your equipment and the installed wiring to
unsure, consult a qualified electrician. eliminate the need for extension cords.
If the circuit breaker trips or the fuse blows regu- If you find it absolutely necessary to use an
larly, your machine may be operating on a circuit extension cord at 220V with your Grizzly Planer:
that is close to its amperage draw capacity.
However, if an unusual amperage draw does not • Make sure the cord is rated for Standard
exist and a power failure still occurs, contact a Service (grade S) or better.
qualified electrician.
• The extension cord must also contain a
ground wire and plug prong.
Motor
V-Belt Cover
Height
Handwheel
Depth Limiter
Height Lock
Knob
Thickness
Scale
Power Switch
Bed Rollers
Extension Rollers
Chip Breaker: Spring loaded fingers or bar that Gibs: Metal strips that hold the planer knives in
presses down on the wood in front of the cut- place.
terhead. The chip breaker prevents excessive
chipping caused by the knives. Gib Bolts: Secures the gib to the knife to keep it
in place.
Snipe: A gouge at the end of the board.
Unpacking
The Model G0550/G0551 was carefully packed
when it left our warehouse. If you discover the
machine is damaged after you have signed for
delivery, please immediately call Customer
Service at (570) 546-9663 for advice.
E D B
D
C
WASH
ETE
PROCESS! Lock Wing ⁄ ''
58
R
Nut Nut
MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE
# 10
Thumb Countersunk
⁄ ''
14
Phillips Phillips
Screw Slotted
Head Head D
Screw Screw ER IA
Screw
M
WASH
ETER
⁄ ''
5 16
⁄ ''
9 16
38 ⁄ ''
Cap Carriage Button
Flange
Screw Bolt Head
Bolt D
Screw ER IA
M
WASH
⁄ ''
7 16
ETER
Phillips
12 ⁄ ''
Hex Phillips Head
Head Head Sheet
⁄ ''
12
Bolt Hex Metal
Setscrew Bolt Screw
DIA
ER
WASHERS ARE MEASURED BY THE INSIDE DIAMETER
ME R
WA H
S
⁄ ''
7 16
TE
DIAM
⁄ ''
58
ER
WASH
ETER
Lock Hex
Washer Washer Nut 12mm
D
4mm ER IA
ASH
METE
⁄ ''
38
DI
W
6mm ER R
5mm
AM
⁄
14 ''
ASH
⁄ ''
ET
5 16
10mm ⁄
38 '' ER
⁄ ''
7 16
W
⁄
12 '' D
15mm ⁄
58 '' ⁄ ''
9 16
ER IA 4mm
8mm ⁄ ''
34 R DIA
M
WASH
20mm
LINES ARE 1MM APART
ASHE
ETER
MET
⁄ ''
78
⁄ ''
5 16
25mm 1'' 10mm
LINES ARE 1⁄16'' INCH APART
ER
W
30mm 11⁄4''
10mm
35mm
11⁄2''
40mm R DIA ER
DI
AM
13⁄4''
ASHE
ASH
45mm
MET
⁄ ''
14
ET
ER
12mm 50mm 2 ER
W
W
55mm 21⁄4'' DIA
60mm ER 6mm D
ME R
ER I
WA H
21⁄2''
AM
S
ASH
65mm 8mm
TE
ET
ER
16mm 70mm 23⁄4'' W
75mm 3 # 10
-12- G0550/G0551 15" Planer
Site Considerations Clean Up
This section covers the basic assembly and Components and Hardware Needed: Qty
adjustment instructions needed to begin opera- Legs ..............................................................4
tion. Complete the assembly in the order provid- Lower Braces ................................................4
ed in this manual and then read the remaining Predrilled Upper Braces ..............................4
portion of the manual before attempting any type Carriage Bolts 5⁄16"-18 x 1⁄2" ........................32
of operation. Hex Nuts 5⁄16"-18..........................................32
Flat Washers 5⁄16" ........................................32
Your safety is important! Please follow the
warnings below during this entire section: Tools Needed:
12/14mm Combo Wrench ............................1
Disconnect power to
the machine during the
entire assembly
process. Failure to do
this may result in seri-
ous personal injury.
Tools Needed:
12/14mm Combo Wrench ..............................2
Strong Persons ..............................................4
Components and Hardware Needed: ....Qty Components and Hardware Needed: ....Qty
Dust Port ........................................................1 Handwheel ....................................................1
Phillips Head Screw M6-1 x 12......................6 Handwheel Handle ........................................1
Hex Nut M10-1.5 ............................................1
Tools Needed: Flat Washer 10mm ........................................1
Phillips Head Screwdriver ..............................1 High/Low Label ..............................................1
To install the dust port: The handwheel is used to raise and lower the
planer cutterhead.
1. Do not connect the planer to a power
source! To install the handwheel:
2. Place the dust port above the outfeed table. 1. Do not connect the planer to a power
See Figure 9. source!
3. Secure the dust port with the Phillips head 2. Place the handwheel over the keyed shaft
screws provided. shown in Figure 10. Make sure the keyway
in the handwheel lines up with the key in the
shaft.
Key
Tools Needed:
12/14mm Combo Wrench ..............................1
Allen Wrench 4mm ........................................1
Setscrews
To install the extension rollers:
Hex Bolts
Level Adjust
Setscrews
Figure 13. Checking extension roller alignment..
The power feed can be set for two feed rates—16 Turn the handwheel to raise or lower the cutter-
FPM and 20 FPM. While the planer is running the head, according to the workpiece thickness.
feed rate can be changed by pulling the feed con-
trol knob (Figure 16). Press the knob in towards Each complete revolution of the handwheel
the machine for 20 FPM and pull the knob out for moves the table by 5⁄32" (4mm).
16 FPM. When the control knob is in the center
position, the power feed is in neutral. Make sure the height scale is properly adjusted
before making a cut. It is always a good idea to
run a test piece through the planer and compare
the thickness of the workpiece to the scale read-
ing.
Depth Limiter
NOTICE
To avoid mechanical damage to the planer,
do not remove the depth limiter.
The anti-kickback fingers hang from a rod sus- The species of wood, as well as its condition,
pended across the front of the cutterhead casting. have a dramatic effect on planing ability. The
Check the fingers to ensure that they swing freely harder the wood (as illustrated by its shear
and easily. See Figure 18. strength), the more difficult it will be to plane. A
brief listing of common hard and soft woods in
relation to their shear strengths and planing diffi-
culty is listed below.
Increasing
White Oak 2,000
Difficulty
White Ash 1,950
Black Cherry 1,700
American Elm 1,510
Black Walnut 1,370
Red Alder 1,080
Basswood 980
Cottonwood 930
Always disconnect Before each use, look for the following condi-
power to the machine tions:
before performing main-
tenance. Failure to do 1. Loose mounting bolts.
this may result in serious
personal injury. 2. Worn switch.
4. Damaged V-belt.
Loose hair and clothing
could get caught in 5. Any other condition that could hamper the
machinery and cause safe operation of this machine.
serious personal injury.
Keep loose clothing
rolled up and long hair
tied up and away from
machinery.
Table
Projectiles from the
The table and other non-painted surfaces on your
machine could cause
machine should be protected against rust and pit-
serious eye injury. Wear
ting. Wiping the table clean after every use
safety glasses at all
ensures that moisture from wood dust does not
times.
remain on bare metal surfaces.
The gearbox is located just behind the handwheel Since all bearings are sealed and permanently
on the right side of the planer. The gearbox trans- lubricated, simply leave them alone until they
fers power from the belt-driven cutterhead to the need to be replaced. DO NOT lubricate them.
power feed rollers. The two-speed transmission
is controlled by a push/pull lever on the right side The following is a list of features and parts
of the planer. When engaged, the power feed that need lubrication:
rollers will move lumber through the planer at
either 16 or 20 feet-per-minute. The center lever Columns/Lead Screws—The four columns
position is neutral. should be lubricated with light machine oil once a
week. The four lead screws should be lubricated
To inspect the gearbox: with general purpose grease once a month. See
Figure 22.
1. Loosen the socket head cap screw on the
gearbox cover, and gently pull the cover off
the roll pins that hold it in place.
Lead screw
2. Move the cutterhead to 1⁄16" under the thick- Figure 30. Screw for column adjustment.
ness of your lumber and feed your test board
through the planer.
4. Slide the gauge block to the opposite side of When making adjustments, all three knives
the cutterhead and check the same knife, must be adjusted the same. DO NOT adjust
rocking back and forth to determine bottom one knife without adjusting the others as
dead center. well. Improper knife height adjustment can
result in damage to knives, poor planer per-
— If the knife does not contact the gauge formance and possible operator injury.
block, use a feeler gauge to determine
the difference between one side and the
other. See Figure 31.
NOTICE
— If the knife bottoms out on the gauge Always adjust the thickness scale after
block, repeat steps 1-3, but start on the adjusting the knives.
opposite side of the cutterhead.
Figure 33. Proper knife setting jig placement. 2. Ensure that the knives are properly adjusted.
5. While holding the position of the knife setting 3. Place the gauge block on the table directly
jig, adjust the jack screws, located on each under the cutterhead.
end of the knife, until they make contact with
the bottom of the knife. 4. Using a 1mm feeler gauge between the
gauge block and the cutterhead, raise the
6. While holding the position of the knife setting table until one of the knives just touches the
jig, tighten the gib bolts down again in the feeler gauge. Rotate the cutterhead by turn-
cutterhead (Figure 34). Tighten the bolts ing the V-belts to be sure the knife is at bot-
evenly from the middle, working toward the tom dead center.
ends.
5. Lock the table by tightening the table lock
7. Repeat these steps for the other two knives. knobs.
Figure 35. Gauge block under chip breaker. 1. Disconnect the machine from the power
source!
To adjust the chip breaker:
2. Lower the table so the gauge block will fit
1. Disconnect the machine from the power under one side of the infeed roller.
source!
3. Raise the table until the gauge block barely
2. If an adjustment is necessary, loosen the touches the infeed roller. See Figure 37. Do
locknuts and turn the setscrews. See Figure not change the position of the table.
36. Stop turning when the bottom of the chip
breaker just touches the gauge block. 4. Slide the gauge block over so it is under the
edge of one of the knives. Turn the cutter-
3. Tighten both locknuts. head until one of the knives is at bottom
dead center over the gauge block.
7. Spin the bed rollers to ensure free move- Regular Pressure Setscrews
ment.
5. Check for any dirt or grit, and clean the The chip deflector keeps chips from falling onto
springs and setscrews if dirty. the outfeed roller. It is the orange plastic plate
located under the top cover.
6. Screw the three regular-pressure setscrews
back in until they are flush with the top of the The beveled edge of the chip deflector should be
head casting. properly adjusted according to your dust collec-
tion setup. However, if the chip deflector is set too
7. Screw the light pressure setscrew (Figure close to the knives, the rotating cutterhead may
42) until it is approximately 1⁄4" above the pull it in and destroy it.
head casting. The feed chain applies addi-
tional tension to the right side of the outfeed To adjust the chip deflector:
roller, so the pressure added by the setscrew
need not be as high. 1. Disconnect the machine from the power
source!
Roller
Cutterhead
Chip Deflector
Height Setscrew Chipbreaker
Check Nut
Overall Dimensions:
Table Size....................................................................................................147/8'' x 20''
Height w⁄ Stand ........................................................................................................53''
Overall Length ..........................................................................................................48''
Overall Width ............................................................................................................28''
Shipping Weight ................................................................................................460 lbs.
Net Weight ........................................................................................................410 lbs.
Foot Print ........................................................................................................25" x 25"
Crate Size ..................................................................................221⁄2"L x 30"W x 29"H
Capacities:
Maximum Depth of Cut..............................................................................................1⁄8''
Maximum Width of Cut ........................................................................................ 147⁄8''
Maximum Cutting Height ........................................................................................61⁄8''
Minimum Stock Thickness........................................................................................3⁄16"
Minimum Stock Length ..............................................................................................8"
Cutterhead Speed ........................................................................................5000 RPM
Cuts per Minute ..................................................................................................15,000
Cuts per Inch.................................................................................................... 63 & 78
Feed Speeds ............................................................................................16 & 20 FPM
Construction:
Table ..................................................................................Precision Ground Cast Iron
Infeed Roller ..........................................................................................Spiral Serrated
Outfeed Roller ......................................................................................Machined Steel
Power Transfer to Feed Rollers:........................................................Gearbox & Chain
Cutterhead Assembly ............................................................................................Steel
Cutterhead ............One piece machined shaft; 3 Knife Slots w/ Sealed Ball Bearings
Motor:
Type ............................................................................TEFC Capacitor-Start Induction
Horsepower............................................................................................................2 HP
Phase ⁄ Voltage ............................................................................Single Phase ⁄ 220 V
Amps ......................................................................................................................12A
Cycle ⁄ RPM..................................................................................60 Hertz ⁄ 3450 RPM
Switch........................................................Magnetic With Thermal Overload Protector
Power Transfer to Cutterhead ..................................................................Triple V-Belt
Bearings ............................................Sealed & Permanently Lubricated Ball Bearings
Features:
Stand............................................................................................................Open Style
Roller Extension Tables ................................................................3 Adjustable Rollers
Cutterhead Movement ..................................Handwheel & 4 Chaindriven Leadscrews
Table Locks ..............................................................................................Two Positive
Chip Chute ......................................................................................................4'' Outlet
Bed Rollers ................................................................................................2 Adjustable
Knife Type / Size / Adjustment ........3 HSS / 15" x 1" x 1⁄8" / Jack-screws and Springs
..........................................................................................Drive Gears Run In Oil Bath
..........................................................................Vertical Scale Calibrations Inch/Metric
Overall Dimensions:
Table Size....................................................................................................147/8'' x 20''
Height w⁄ Stand ........................................................................................................53''
Overall Length ..........................................................................................................48''
Overall Width ............................................................................................................28''
Shipping Weight ................................................................................................560 lbs.
Net Weight ........................................................................................................450 lbs.
Foot Print ........................................................................................................21" x 21"
Crate Size ................................................................................303⁄4"L x 30"W x 481⁄2"H
Capacities:
Maximum Depth of Cut..............................................................................................1⁄8''
Maximum Width of Cut ........................................................................................ 147⁄8''
Maximum Cutting Height ........................................................................................61⁄8''
Minimum Stock Thickness........................................................................................3⁄16"
Minimum Stock Length ..............................................................................................8"
Cutterhead Speed ........................................................................................5000 RPM
Cuts per Minute ..................................................................................................15,000
Cuts per Inch.................................................................................................... 63 & 78
Feed Speeds ............................................................................................16 & 20 FPM
Construction:
Table ..................................................................................Precision Ground Cast Iron
Infeed Roller ..........................................................................................Spiral Serrated
Outfeed Roller ......................................................................................Machined Steel
Power Transfer to Feed Rollers:........................................................Gearbox & Chain
Cutterhead Assembly ............................................................................................Steel
Cutterhead ............One piece machined shaft; 3 Knife Slots w/ Sealed Ball Bearings
Motor:
Type ............................................................................TEFC Capacitor-Start Induction
Horsepower............................................................................................................3 HP
Phase ⁄ Voltage ............................................................................Single Phase ⁄ 220 V
Amps ......................................................................................................................18A
Cycle ⁄ RPM..................................................................................60 Hertz ⁄ 3450 RPM
Switch........................................................Magnetic With Thermal Overload Protector
Power Transfer to Cutterhead ..................................................................Triple V-Belt
Bearings ............................................Sealed & Permanently Lubricated Ball Bearings
Features:
Roller Extension Tables ................................................................3 Adjustable Rollers
Cutterhead Movement ..................................Handwheel & 4 Chaindriven Leadscrews
Table Locks ..............................................................................................Two Positive
Chip Chute ......................................................................................................4'' Outlet
Bed Rollers ................................................................................................2 Adjustable
Knife Type / Size / Adjustment ........3 HSS / 15" x 1" x 1⁄8" / Jack-screws and Springs
..........................................................................................Drive Gears Run In Oil Bath
..........................................................................Vertical Scale Calibrations Inch/Metric
..................................................................................Powder Coated Paint on Cabinet
132
22
20 3
55
119
118
117
116 137
124 166
123 125 106
122
121 22
120 165
118 15
117 169
116 126
165
127 167
137
128
168
31
30
-43-
149
142 G0551 Stand
141 150
140
151
154
173
174
175
17
176
143
177
178
179
-46-
Troubleshooting Guide
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
Motor will not start. 1. Low voltage. 1. Check power line for proper voltage.
2. Open circuit in motor or loose 2. Inspect all lead connections on motor for loose or open connections.
connections.
Motor will not start; fuses or 1. Short circuit in line cord or plug. 1. Inspect cord or plug for damaged insulation and shorted wires.
circuit breakers blow. 2. Short circuit in motor or loose 2. Inspect all connections on motor for loose or shorted terminals
connections. or worn insulation.
3. Incorrect fuses or circuit breakers 3. Install correct fuses or circuit breakers.
in power line.
Motor stalls (resulting in 1. Short circuit in motor or loose 1. Inspect connections on motor for loose or shorted terminals or worn
blown fuses or tripped cir- connections. insulation.
cuit). 2. Low voltage. 2 Correct the low voltage conditions.
3. Incorrect fuses or circuit breakers 3. Install correct fuses or circuit breakers.
in power line.
4. Motor overloaded. 4. Reduce load on motor.
Machine slows when oper- 1. Feed rate too high. 1. Feed workpiece slower.
ating. 2. Depth of cut too great. 2. Reduce depth of cut.
Loud, repetitious noise com- 1. Pulley setscrews or keys are mis- 1. Inspect keys and setscrews. Replace or tighten if necessary.
ing from machine sing or loose. 2. Tighten fan or shim cover.
2. Motor fan is hitting the cover.
3. V-belt is defective 3. Replace V-belt. See Maintenance.
Machine is loud when cut- 1. Excessive depth of cut. 1. Decrease depth of cut.
ting. Overheats or bogs 2. Knives are dull 2. Sharpen knives.
down in the cut.
Infeed roller marks are left 1. Depth of cut too shallow. 1. Increase depth of cut.
on the workpiece.
Outfeed roller marks are left 1. Too much spring tension on feed 1. Refer to Feed Roller Pressure section for adjustment.
on right side of workpiece. roller.
Cannot control snipe. 1. Long or heavy board sags as it 1. Lift up on unsupported end of board as it enters and exits
enters and exits. cutterhead.
Chip buildup on outfeed 1. Chips working their way back under 1. Lay duct tape over the mounting bolts along the outside edge to seal
roller. the chip deflector. any possible gaps.
Machine howls on startup. 1. Chip deflector too close to the 1. Move chip deflector back 1/8" to 1/4" from the cutterhead.
cutterhead.
Single Phase
Power Source Green
Black White
A1
1L1 3L2 5L3
Black
NO 13
Magnetic Switch
NC 15
Ground
16 NC
14 NO
18 12
15
Reset
G0551
1/2 3/4 5/6
26 18
22
96 98
95
Black
MOTOR
Black
Green
White
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
___Other__________________________________________________ __________________________________________________________
___$20,000-$29,999 ___$60,000-$69,999 14. What new accessories would you like Grizzly Industrial to carry?
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999 __________________________________________________________
___$50,000-$59,999 ___$90,000 +
__________________________________________________________
5. What is your age group?
15. What other companies do you purchase your tools and supplies from?
___20-29 ___50-59
__________________________________________________________
___30-39 ___60-69
___40-49 ___70 + __________________________________________________________
6. How long have you been a woodworker? 16. Do you think your purchase represents good value?
Place
Stamp
Here
Name_______________________________
Street_______________________________
City______________State______Zip______
• SECURE ORDERING
• ORDERS SHIPPED WITHIN 24 HOURS
• E-MAIL RESPONSE WITHIN ONE HOUR
-OR-