Professional Documents
Culture Documents
PARATEX TH Waterproofing
Two-components, Cement-based, polymer-modified waterproof coating
ADVANTAGES SUBSTRATES
• Good bonding strength: with concrete or mortal Adhesion of PARATEX TH
• Durable: Scratch resistance and weather, moisture, waterproof Concrete and Mortar: very well
• Self-UV resistance: No need to coating topcoat Method Type Substrate Adhesion (N/mm2)
Concrete 1.10
• Good water pressure resistance: 491 kPa. (Positive side) Method A
Mortar 0.90
• Flexible and elastic: Resistance surface crack and accommodates
Concrete 1.60
normal building movement (*Elongation 240% JIS K 6251) and Method B
Mortar 1.40
(*Elongation 340% ASTM D412:06a (2013)) *PARATEX TH A Method
Concrete 0.99
• Seamless: Surface smooth and without joint can topcoat many material Method C
Mortar 0.74
for finishing, can topcoat by painting , Repair without joint with exist
Concrete 2.20
waterproof surface Method D’
Mortar 1.70
• Crack-bridging: Reinforcement & Repair surface concrete crack
Remark: Designated by JIS A 5371
• Easy to apply & repair: PARATEX TH can apply on wet surface moisture
Wet Concrete: Very well
no effect for quality and application and can repair on exist waterproof
Method Type Substrate Adhesion (N/mm2)
surface (PARATEX TH surface) directly no need to apply primer again
Method A Concrete 1.13
• Easy to planning and order: PARATEX TH can use many type of
Method B Concrete 2.31
Structure depend on mixing ratio, primer mixing by ourselves material
Method C Concrete 1.13
• Nontoxic: Water based waterproofing safe and harmless to other
Method D’ Concrete 2.01
creatures as well as to the environment
Remark: Designated by JIS A 5371
APPLICATION RANGE
Modified Silicon and Urethane: Well
LOCATION: Depend on type of PARATEX TH Method Type Substrate Adhesion (N/mm2)
• PARATEX TH A Method: Toilet, Bathroom, Kitchen, Balcony, Parapet, Modified Silicon 0.51
Method A
Reinforcement and repair crack work (Slab and wall) Urethane 0.53
Basement (Outside and inside), swimming pool, water park Urethane 0.53
Remark: Designated by JIS A 5371, Only Method A and Method D’ because
• PARATEX TH C Method: Rooftop floor, Outside passageway, Roof
just reinforcement Application.
balcony, External staircase, Long span slab
Caution: Contact OZEKI-Chemical (Thailand) for use over existing
• PARATEX TH D’ Method: Protect & Repair outside wall (After plastering)
membranes, covering materials, and any other substrates not listed
Technical Data Sheet
PARATEX TH Waterproofing
Two-components, Cement-based, polymer-modified waterproof coating
• PARATEX TH A Method: PARATEX TH Emulsion 1 pail + PARATEX TH Admixture 1 bag + PARATEX TH Cloth(Reinforcement Application)
• PARATEX TH C Method: PARATEX TH Emulsion 1 pail + PARATEX TH Admixture 1 bag + PARATEX TH Cloth(Reinforcement Application)
+ PARATEX TH Mesh
• Fully cured: Dry air cured 72 hour Application: Avoid application if rain, and be careful for recoat time
(Except. PARATEX TH D only 2-5 hour) make sure for last waterproofing layer is dried sufficiently. Figures
Remark: For PARATEX TH B Method, if application in portable water on standard specifications may change depending on the condition.
tank should be curing by water 5 days after dry air cured 72 hour
SAFETY DATA
and take-out the water The liquids components are non-toxic by themselves, but powder
component is cement based and may be irritating to skin and
SHELF LIFE
eyes. Gloves and eye protection should be used.
At least 12 months in its unopened packaging, when stored in a dry
In case of contact with eyes, rinse off thoroughly with clean water
and cool place, and for PARATEX TH Admixture keep away from
then consult a doctor.
stock on the floor directly. Protect the materials from moisture.
*For more information, refer to MSDS (Material safety data sheet)
Technical Data Sheet
PARATEX TH Waterproofing
Two-components, Cement-based, polymer-modified waterproof coating
Remark: Should be making concrete smooth surface, before start PARATEX TH *Remark: Filler depend on situation
work. Because PARATEX TH waterproofing can’t adjust and make it smooth, Material for filler - Modified Silicone: for A, C Method
depending on exist concrete surface. - PARATEX TH Hard Consistency (Harder Mix): for B Method
• Dry curing: PARATEX TH can continue application immediately after PARATEX TH Primer
Reinforcement layer get dried already, no need wait for curing time. PARATEX TH A Method
REINFORCEMENT APPLICATION
Material for Reinforcement Method:
PARATEX TH PARATEX TH
Material Name Water
Emulsion Admixture Remark: PARATEX TH A Method application lap with concrete more than 50 mm.
PARATEX TH Primer 1 - 19
• Rock Pocket Method: For
PARATEX TH Hard Consistency
1 4 - - After removed weak surface concrete (Honeycomb), Should be repaired
(Harder Mix)
by PARATEX TH mixed Mortal before start reinforcement application.
PARATEX TH A Method 3 2 - After concrete surface get dried start reinforcement application.
Modified Silicone - - - Method: PARATEX TH Primer → PARATEX TH A Method (0.8 Kg/m2)
Material for repairing surface concrete:
• FORM TIE
PARATEX TH
Material Water Cement Sand
Emulsion
Form Tie
c PARATEX TH Mixed
1 4 10 20
Mortal PARATEX TH Primer
Remark: This’s method only preparation work for waterproofing work, can’t use for PARATEX TH A Method
repair concrete structure problem.
① Application of Primer
Mix PARATEX TH Emulsion and water as following ratio. Apply to surface by
Brush, Roller or Spray.
Quantity Remark: PARATEX TH A Method application wide more than 100 mm.
Material Mixing Ratio Uses (Kg/m2)
(Kg/m2) • Form Tie Method:
PARATEX TH Emulsion 1 0.005 - After removed plastic cone, Should be repaired by PARATEX TH mixed
0.1 Mortal before start reinforcement application.
Water 19 0.095
After concrete surface get dried start reinforcement application
Curing time min. 30 minute Method: PARATEX TH Primer → PARATEX TH A Method (0.8 Kg/m2)
Technical Data Sheet
PARATEX TH Waterproofing
Two-components, Cement-based, polymer-modified waterproof coating
COLD JOINT AND CONSTRUCTION JOINT EXTERNAL CORNER & INTERNAL CORNER
Remark: PARATEX TH A Method application wide more than 100 mm. or overlap more
q than PARATEX TH Cloth 50 mm. per side
Remark: PARATEX TH A Method application wide more than 100 mm.
PARATEX TH Primer
Cold joint and Construction joint
PARATEX TH Cloth
PARATEX TH Primer
PARATEX TH A Method
PARATEX TH A Method
COMMUNICATING PIPE
Communicating pipe
PARATEX TH Primer
PARATEX TH A Method
PARATEX TH A Method
Remark: PARATEX TH A Method application wide more than 50 mm. from pipe
Remark: PARATEX TH A Method application wide more than 50 mm. from roof drain
PARATEX TH Waterproofing
Two-components, Cement-based, polymer-modified waterproof coating
STANDARD SPECIFICATIONS
METHO
⑤
④
SPECIFICATIONS
① PRIMER 0.1 Kg/m 2 ① PRIMER 0.1 Kg/m 2 ① PRIMER 0.1 Kg/m 2 ① PRIMER 0.1 Kg/m 2
② PARATEX TH A METHOD 0.8 Kg/m 2 ② PARATEX TH B METHOD 1.5 Kg/m2 ② PARATEX TH MESH ② PARATEX TH D’ METHOD 0.25 Kg/m2
③ PARATEX TH A METHOD 0.8 Kg/m 2 ③ PARATEX TH B METHOD 1.5 Kg/m 2 ③ PARATEX TH A METHOD 0.6 Kg/m2 ③ PARATEX TH D’ METHOD 0.25 Kg/m2
④ PARATEX TH A METHOD 0.6 Kg/m 2
Confirm reinforcement layer had been dried, Confirm reinforcement layer had been dried, Confirm reinforcement layer had been dried, PARATEX TH D’ Method can apply directly to
before start apply PARATEX TH A Method before start apply PARATEX TH B Method before start apply PARATEX TH C Method painting surface* but confirm the surface to be
Step1. Application of PARATEX TH Primer, Step1. Application of PARATEX TH Primer, Step1. Application of PARATEX TH Primer, coated must be sound and clean before start
apply by roller, brush or spray 0.1 Kg/m 2 all apply by roller, brush or spray 0.1 Kg/m 2 all apply by roller, brush or spray 0.1 Kg/m 2 all the application (cleaning surface by sand paper). In
the application area surface the application area surface application area surface case of apply directly to concrete or mortal,
(Curing min. 30 minute) (Curing min. 30 minute) (Curing min. 30 minute) PARATEX TH Primer will required.
Step2. Application of PARATEX TH A Method, Step2. Application of PARATEX TH B Method, Step2. Application of PARATEX TH C Method, * Acryl painting colour
1st coat apply by roller, brush total quantity 1st coat apply by trowel total quantity 1.5 place and fix PARATEX TH Mesh all the Step1. Application of PARATEX TH Primer,
0.8 Kg/m2 all the application area surface Kg/m2 all the application area surface application area surface (overlap not less than apply by roller, brush or spray 0.1 Kg/m 2 all the
(Curing 3 hour) (Curing 3 hour) 50 mm.) application area surface
METHOD STATETMENT
Step3. Application of PARATEX TH A Method, Step3. Application of PARATEX TH B Method, Step3. Application of PARATEX TH C Method, (Curing min. 30 minute)
2nd coat confirm drying of 1st coat and apply 2nd coat confirm drying of 1st coat and apply 1st coat apply by Roller total quantity 0.6 Step2. Application of PARATEX TH D’ Method,
2nd coat as same as 1st 2nd coat as same as 1st Kg/m2 all the application area surface (Curing 1st coat apply by roller or brush total quantity
Step4. Take 72 hour (3 day) for curing time Step4. Take 72 hour (3 day) for curing time 3 hour) 0.25 Kg/m2 all the application area surface or
after finish apply 2nd after finish apply 2nd Step4. Application of PARATEX TH C Method, only repair crack (cover not less than 100 mm)
2nd coat confirm drying of 1st coat and apply (Curing 3 hour)
2nd coat by trowel total quantity 0.6 Kg/m 2 for Step3. Application of PARATEX TH D’ Method,
make a flat surface all the application area 2nd coat confirm drying of 1st coat and apply
surface (Curing 3 hour) 2nd coat as same as 1st
2nd coat confirm drying of 1st coat and apply Step4. Take 6 hour for curing time after finish
2nd coat as same as 1st apply 2nd and must be to top coating by top
Step5. Application of PARATEX TH C Method, coating material* (Acryl base, Poly urethane
3rd coat confirm drying of 2nd coat and apply base, Acryl silicon base)
3rd coat by roller total quantity 0.6 Kg/m 2
Step6. Take 72 hour (3 day) for curing time
after finish apply 2nd
***Equipment tools