Professional Documents
Culture Documents
3 Steps For Solving The Two Method Wattmeter Problem - Electrical PE Review
3 Steps For Solving The Two Method Wattmeter Problem - Electrical PE Review
E L E CT R I CA L P E
R E V I E W < h t t p s : / / w w w. e l e c t r i c a l p e r e v i e w
Share Tweet S 0
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 1/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
In Part 1 of the Two Method Wattmeter series, we are going to show you:
1. The three “rules” for using two wattmeters to measure the total power of a
three-phase balanced or unbalanced circuit
*For example: if the negative (-) voltage reference for wattmeter 1 (W1) is on
C phase, then the negative (-) voltage reference for wattmeter 2 (W2) MUST
also be on C phase.
Rule #1 – The negative (-) voltage reference for both wattmeters MUST be on
the same phase (both on A, B, or C).
Rule #2 – The line current measured on each phase MUST be the same phase
as the positive (+) voltage reference for each wattmeter! *For example, if the
positive (+) voltage reference for wattmeter 1 (W1) is on A phase, then
1 (W1) MUST ALSO h li A h
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 2/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
*For example: if the positive (+) voltage reference for wattmeter 1 (W1) is on
A phase, then the positive (+) voltage reference for wattmeter 2 (W2) MUST
NOT be on A phase.
2. How to derive the two method wattmeter formula commonly seen in books
depending on which phases the positive (+) and negative (-) voltage polarity for
wattmeter 1 (W1) and wattmeter 2 (W2) are connected to:
P3ø = W1 + W2
In the configuration that wattmeter 1 (W1) and wattmeter 2 (W2) are shown
connected in this video, we can expand this formula into:
P3ø = |VAC|·|Ia|·cos(θ-30º) + |VBC|·|Ib|·cos(θ+30º)
In Part 2 of the Two Method Wattmeter series, we are going to show you:
1. How to draw the phasor diagram for both wattmeter 1 (W1) and wattmeter 2
(W2) depending on how each wattmeter is connected according to the three
“RULES” from Part 1.
The phasor diagrams will depend on which phases the positive (+) and
negative (-) voltage polarity are connected to for wattmeter 1 (W1) and
wattmeter 2 (W2).
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 3/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
2. How to easily derive the correct power angle (θ) for both wattmeter 1 (W1)
and wattmeter 2 (W2) graphically using both of the phasor diagrams we set up.
*Here’s the trick! One of the line voltages being measured by either
wattmeter 1 (W1) or wattmeter 2 (W2) depending on how they are connected
will be NEGATIVE (CBA) SEQUENCE, and one will be positive (ABC) sequence.
*Inside the cosine function in the power formula, one of the wattmeters will
have θ MINUS thirty degrees while the other will have θ PLUS thirty degrees
depending on how both wattmeters are connected:
cos(θ-30º)
cos(θ+30º)
(Go back to top)<#top>
In Part 3 of the Two Method Wattmeter series, we are going to show you:
1. How to quickly identify which of the two wattmeters (W1 or W2) has the θ
MINUS thirty degrees inside the cosine function, and which has the θ PLUS thirty
degrees inside the cosine function WITHOUT taking the time to draw out the
phasor diagrams.
*It’s extremely important to know how to draw both of the phasor diagrams
(Part 2 in the Two Method Wattmeter Series) and how to derive the power
formula commonly see in books (Part 1 in the Two Method Wattmeter Series)
because in doing so you’ll be able to answer just about any and every two
method wattmeter question on the Electrical Power PE Exam.
*HOWEVER! Time is really important during the exam because you only have a
certain amount of time to answer each question.
*Because of this, sometimes it is helpful to know how to QUICKLY identify
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 4/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
2. If the system is positive sequence (ABC), look for the negative sequence
voltage.
In a positive sequence (ABC) system:
In comparison, in the example circuit used in the video, wattmeter 2 (W2) is
connected across B (+) to C (-).
The line voltage that wattmeter 2 (W2) is measuring is the positive
sequence B line voltage (VBC).
This means that the formula for the power measured by wattmeter 2
(W2) will have the theta plus 30º term inside the cosine function:
The wattmeter (W1 or W2) that has the 30º minus theta term inside the
cosine function and the wattmeter (W1 or W2) that has the 30º plus theta
term inside the cosine function always depends on how the wattmeters are
connected.
There will always be one wattmeter measuring a negative sequence line
voltage, and a wattmeter that measuring a positive sequence line voltage.
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 5/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
If the system is balanced, it does not matter which wattmeter formula has the
30º minus theta term inside the cosine function, and which wattmeter formula
has the 30º plus theta term inside the cosine function since the line voltages
magnitude and line current magnitudes will be equal.
For example, if our example circuit used in the video is balanced then:
|VCA| = |VBC| = |VL| and |Ia| = |Ib| = |IL|
We can use this to simplify the two method wattmeter formula for a balanced
system only:
P3ø = |VCA||Ia|cos(θ-30º) + |VBC||Ib|cos(θ+30º)
P3ø = |VL||IL|cos(θ-30º) + |VL||IL| cos(θ+30º)
Would you like to work through practice problems on the Two Method
Wattmeter?
Chapter 1.1 Instrument
Transformers<https://courses.electricalpereview.com/courses/take/electrical-power-
review-course/texts/562300-1-instrument-transformers#twowattmeter> in our online
course for the Electrical Power PE Exam has more information on the two
method wattmeter and practice problems with detailed solutions.
Do you have any more questions on the two wattmeter method, or thoughts to
share on the subject?
Leave a comment below and join the discussion!
(Go back to top)<#top>
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 6/7
12/27/22, 10:14 PM 3 Steps for Solving the Two Method Wattmeter Problem - Electrical PE Review
Ready to get access to the course and start studying for the Electrical Power PE Exam?
S I G N U P N OW FO R F R E E
( H T T P : / / C O U R S E S . E L E C T R I C A L P E R E V I E W. C O M / E N R O L L / 4 4 2 7 1 ? E T = F R E E )
(http://courses.electricalpereview.com/enroll/44271?et=free_trial)
S TA RT N OW FO R F R E E ( H T T P : / / C O U R S E S . E L E C T R I C A L P E R E V I E W. C O M / E N R O L L / 4 4 2 7 1 ? E T = F R E E _ T R I A L )
V I E W A L L C O U R S E S ( H T T P S : / / C O U R S E S . E L E C T R I C A L P E R E V I E W. C O M / )
https://www.electricalpereview.com/3-steps-for-solving-the-two-method-wattmeter-problem/#1 7/7