Professional Documents
Culture Documents
Leica Geosystems AG
CH-9435 Heerbrugg
(Switzerland) Copyright by Leica Geosystems AG, Heerbrugg, Switzerland 2022
Chapter Overview
15
I SML GS10-GS14-GS15-GS16 - 08/2020
1 Legal, Safety & Environmental Issues / Symbols
1.1 Rechtsfragen / Legal questions / Question juridiques / Cuestiones de derecho
Copyright Copyright Copyright
Ohne vorherige schriftliche Erlaubnis der Firma Leica Without prior permission in writing by Leica Geosys- Sans autorisation écrité préalable de Leica Geosys-
Geosystems AG (Schweiz), darf dieses Dokument tems AG (Switzerland), this document shall not be tems AG il est interdit de reproduire ce document,
weder insgesamt noch auszugsweise mit mecha- reproduced as a whole or in part, by mechanical, entièrement ou partiellement, par quelque procédé
nischen, fotografischen, elektronischen oder photographic, electronic, or other means (including que ce soit (mécanique, électronique ou autres, y
irgendwelchen anderen Mitteln (einschließlich ihrer into or transmission in machine-readable form); stored compris la transformation ou la transmission sous une
Umwandlung oder Übertragung in maschinenlesbarer in any retrieval system; used for any purpose other forme exploitable machinellement), de le y mettre en
Form) kopiert, in einem Informationsspeicher abge- than that/those for which it is intended; nor made mémoire sur un support informatique, de l'utiliser à
legt, außerhalb des dafür vorgesehenen Zwecks oder accessible or communicated in any form to any third d'autres fins que celles prévues, de la rendre acces-
in irgend einer Form an von Leica Geosystems AG, party not expressly authorized by Leica Geosystems sible uo de le transmettre sous quelque forme que ce
Heerbrugg nicht ausdrücklich befugte Dritte AG to have access thereto. soit à des tiers non authorisés expressément par
zugänglich gemacht oder abgegeben werden. Leica Geosystems AG.
Legal, Safety & Environmental Issues / Symbols 1-1 SML GS10-GS14-GS15-GS16 - 08/2016
Copyright
Sin el permiso previo por escrito de Leica Geosys-
tems AG (Suiza), este documento no puede ser repro-
duzido total ni parcialmente por medios mecánicos,
fotográficos, electrónicos o de calquier otro tipo
(incluyendo la conversión en forma legible por
máquinas), ni ser introducido en un sistema
informático o utilizado para fines distintos de los
previstos. Bajo ningún concepto puede hacerse
accesible a terceros sin la autorización explicita de
Leica Geosystems AG.
Responsabilidad
Este documento va dirigido exclusivamente al
personal técnico cualificado que disponga de los
conocimientos requeridos. Estos técnicos deben
haber atendido en Leica Geosystems AG el corre-
spondiente curso de formación de forma satisfactoria,
así como trabajar, bien en una de las sociedades del
Grupo Leica, bien en representaciones de o talleres
autorizados por Leica Geosystems AG. Si este docu-
mento se utiliza por personal no cualificado, Leica
Geosystems AG declina toda responsabilidad en
caso de producirse, directa o indirectamente, daños
debidos a un empleo inapropiado y/o interpretación
errónea de este documento.
Legal, Safety & Environmental Issues / Symbols 1-2 SML GS10-GS14-GS15-GS16 - 08/2016
1.2 Sicherheit / Safety / Sécurité / Seguridad / Umwelt /Environment / Environnement / Ambiente
Für die Servicetechniker/in gelten folgende Pflichten: Le personnel technique a les obligations suivantes.
Sie verstehen und befolgen die Sicherheitsinfor- Comprendre et suivre les consignes de sécurité et
mationen und die Instruktionen auf dem Produkt les instructions mentionnées sur le produit ainsi
sowie in der Gebrauchsanweisung. que dans le manuel d'utilisation.
Sie kennen die ortsüblichen gesetzlichen, betrie- Connaître, en matière de prévention des acci-
blichen und ausserbetrieblichen Unfallver- dents, les prescriptions locales en vigueur dans
hütungsvorschriften im Wissen, dass sich diese l'entreprise et à l'extérieur de l'entreprise.
auf dem aktuellsten Stand befinden. Informer immédiatement Leica Geosystems AG
Sie benachrichtigen Leica Geosystems AG schrift- par écrit si l'équipement présente un défaut de
lich, sobald an der Ausrüstung Sicherheitsmängel sécurité.
auftreten. Vous devez suivre la réglementation locale en
Sie befolgen die landesüblichen Vorschriften betr- matière d'élimination de l'ensemble des pièces
effs Entsorgung von sämtlichen Einzelteilen des isolées de l'instrument ainsi que des accessoires.
Instrumentes sowie dessen Zubehör.
Legal, Safety & Environmental Issues / Symbols 1-3 SML GS10-GS14-GS15-GS16 - 08/2016
1.3 Service Sicherheitshinweise / Service safety hints
Gebrauchsanweisung überprüfen (Erweiterung a,b,c...) welcher der Board- precaution must strictly be observed when-ever
Die Gebrauchsanweisung enthält, neben den nummer folgt. instruments with electronic components are opened
Hinweisen zur Verwendung auch wichtige Sicherheit- or dismantled. For more information con-cerning ESD
shinweise. Lesen Sie die Gebrauchsanweisung vor Justierungen / Service Prüfprotokoll precautions refer to Service News 44/2002.
der Inbetriebnahme des Instruments sorgfältig durch. Nach dem Auswechseln einer Platine oder einer
Einheit, sind jedesmal die notwendigen Justierungen Revision documents and Service News
Reparaturen oder Abgleiche auszuführen. Before exchanging a PCB or a sub-assembly, refer to
Dieses Handbuch darf nur von bei Leica Geosystems Nach Beendigung einer Reparatur und / oder einer the section “Service News / Revisions”, in order to
ausgebildeten Servicetechniker/in verwendet werden. Justierung muss das Instrument immer vollständig, ensure that the PCB or sub-assembly can, in fact, be
Dieses Handbuch ersetzt keinen entsprechenden gemäss Service Prüfprotokoll, überprüft werden. Die fitted in that particular instrument. Always start by
Ausbildungskurs. Im weiteren wird angenommen, Service Prüfprotokolle müssen aufbewahrt werden. inspecting the modification index (extension a,b,c...)
dass die Gebrauchsanweisung, welche jedem Instru- which follows the board number on the PCB.
ment beiliegt bekannt ist. Der Servicetechniker muss
in der Lage sein, dieses Instrument gemäss der Adjustments / Service test report
Gebrauchsanweisung zu handhaben, bevor er mit After exchanging a PCB or a sub-assembly, always
dem Studium dieses Handbuches beginnt. User manual carry out the adjustments stipulated.
The user manual also contains important safety After completing a repair or an adjustment, always
Öffnen oder Demontage von Instrumenten notices. Please read the user manual thoroughly carry out a complete inspection of the instrument in
Instrumente dürfen nur in sauberen, möglichst staub- before switching on the instrument for the first time. accordance with the service test report. File the
freien Räumen durch ausgebildete Techniker geöffnet completed test report.
oder demontiert werden. Damit soll gewährleistet Introduction
sein, dass die Funktion eines Instruments nicht durch This handbook is only for use by Leica Geosystems-
eingedrungenen Staub oder sonstige Verunreini- trained service personnel. It is no substitute for atten-
gungen beeinträchtigt wird. dance at an appropriate training course. The reader is
Beim Öffnen von Geräten mit elektronischen Kompo- assumed to be familiar with the user manual supplied
nenten müssen zusätzlich die Schutzvorkehrungen with each instrument. Before starting to study the
bzgl. ESD-Sicherheit beachtet werden. Nähere present handbook, the service technician must be
Hinweise bzgl. ESD-Schutz sind in Service News 44/ able to use the instrument in accordance with the user
2002 zu finden. manual.
Legal, Safety & Environmental Issues / Symbols 1-4 SML GS10-GS14-GS15-GS16 - 08/2016
1.4 Symbole / Symbols
Liste der Symbole und deren Bedeutung Listing of symbols and their meaning
GEFAHR:
Unmittelbare Gebrauchsgefahr, die
zwingend schwere Personenschäden
DANGER:
Indicates an imminently hazardous
situation which, if not avoided, will
oder den Tod zur Folge hat. result in death or serious injury.
WARNUNG: WARNING:
Gebrauchsgefahr oder sachwidrige Indicates a potentially hazardous situ-
Verwendung, die schwere Personen- ation which, if not avoided, could result
schäden oder den Tod bewirken kann. in death or serious injury.
VORSICHT:
Gebrauchsgefahr oder sachwidrige
Verwendung, die nur geringe Person-
CAUTION:
Indicates a potentially hazardous situ-
ation which, if not avoided, may result
enschäden, aber wesentliche Sach-, in minor or moderate injury and/or
Vermögens- oder Umweltschäden appreciable material, financial and
bewirken kann. environmental damage. The symbol is
also used to alert against unsafe prac-
tices.
Legal, Safety & Environmental Issues / Symbols 1-5 SML GS10-GS14-GS15-GS16 - 08/2016
Legal, Safety & Environmental Issues / Symbols 1-6 SML GS10-GS14-GS15-GS16 - 08/2016
2 Revisions / Service News
Revisions
Revisions of this Service Manual are published on the
“myServiceProducts” website for downloading.
Service News
Service News containing important information about
modifications, product improvements, etc., have to be
downloaded from the “myServiceProducts” website.
4-9, 4-10
4 4-9, 4-10, 4-11 Block diagram illustrations updated
4-11, 4-12
9 9-1, 9-2 9-1, 9-2 "197866 Shellac fluid" replaced by "233563 Shellac (50g)"
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
www.leica-geosystems.com
Section Replace / add Changes on Reason for Revision
pages page
12-5 "842568 SIM/SD card cover GS16" (not GS14), "847208 Battery
cover gasket" (not GS14/GS16), until stock lasts while stock
lasts, Processor boards re-arranged
12-21, 12-22 99770708 AS05 removed, 99765733 AR25 (Rev 3.0) removed, re-
arranged
13-5, 13-6 13-5 Torque screwdrivers added, picture "777906 Antenna Holder"
updated, "197866 Shellac fluid" replaced by "233563 Shellac (50g)",
13 E-Mail link added, adjustment table of "937964 Cable Tie Pliers"
added
Steps to be taken: Replace the whole contents of the manual with this revision
File: Insert this sheet in section 2
Best regards,
Peter Sandner
Central Technical Service GNSS
Introduction We are pleased to inform about a new Service Test PC for WLAN testing.
This box should also be usable for Bluetooth tests in the future.
This service test PC is a replacement for the WLAN test box 777247 that is no longer
available.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
AC Power The power cord is not included and must be ordered separately.
Cables
Phase-out The previous WLAN test box 777247 box is no longer available. Existing WLAN test
boxes can still be used. It is not possible to use 2 WLAN boxes at the same time.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction Referring to Service News 29-2016 "GS Unlimited Upgrade Packages" we would like
to inform that the mentioned "Unlimited upgrade packages" for
GS10 / GS14 / GS15 / GS25 will no longer be free of charge from 01.01.2023
onwards.
Service Action In case of an upgrade to OEM7 one of these upgrade kits need to be purchased:
▪ 99841798 - GUS106 Upgrade Kit GS10 OEM7xx
▪ 99841799 - GUS107 Upgrade Kit GS14 OEM7xx
▪ 99841800 - GUS108 Upgrade Kit GS15 OEM7xx
▪ 99841801 - GUS109 Upgrade Kit GS25 OEM7xx
Please keep in mind that a refund is no longer offered when sending back ME4 or
OEM6 via eSpareBack, as informed in Service News 31-2022.
Service Manual Detailed descriptions about the upgrading process are already mentioned in the
Service Manuals, refer to chapter "Upgrades".
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
Peter Sandner
Central Technical Service GNSS
Introduction The eSpareBack process for all variants of ME4 and OEM6 has been stopped
in case of near service phase-out. From now on it is not possible anymore to
send back defective ME4 and OEM6 measurement engines for a refund.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phase-Out List We kindly remind you to check the official Service Obligation List on myWorld
regularly. All instruments and phase-out information are available there.
Service Support For assistance with any service-related issues please contact:
service.support@leica-geosystems.com
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
SN3122 - eSpareBack process stopped for ME4 and OEM6 _en 2/2
Service News
No 18-2022
Date 20th May 2022
From Dietmar Hehle
To Service staff / Representatives
Filing Service Manual:
- GS10/GS14/GS15/GS16
- GS18
- GS07/GS08(plus)/GS12/GGxx/GMX9xx
- iCG30
- iCG60/iCG80
- iCG70
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phased out With the introduction of the new Measurement Engines, the predecessor
Measurement articles 99949187 (OEM719L) and 99949188 (OEM719BL) has been phased
Engines out. Defective ME`s of 97949187 and 97949188 still can be returned via
eSpareBack process.
Service Manual The new Measurement Engines will be added to the Service Manuals
"GS10/GS14/GS15/GS16", " GS18", " iCG30", " iCG60/iCG80", " iCG70", and
"GS07/GS08(plus)/GS12/GGxx/GMX9xx" within the next revision.
Maja Tool With the next revision of "Maja.exe" all the new Measurement Engines will be
shown.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction A new variant of SATEL radio M3-TR9 (HW 3.4) had to be introduced for GS16,
GS18, iCG70 and CCD20/21 due to procurement problems of the SATEL
processor. The new radio variants have the same performance as the previous
ones, also the same Leica article number. They can be identified via the
hardware version on the label or via SERIS readout.
Spare Part 99855730 SATEL M3-TR9 (TA31) 99855730 SATEL M3-TR9 (TA31)
HW 1.3 / 1.4 (1024kB version) HW 3.4 (512kB version)
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service Software In SERIS the different variants can be identified via hardware version.
SATEL Radio The SATEL radio firmware to be used is different for both variants of M3-TR9.
Firmware M3-TR9 Hardware variant SATEL firmware
1.3 / 1.4 (1024kB) 07.38.2.5.1.4
3.4 (512kB) 07.67.3.6.0.8
Instrument Firmware For GS18 and iCG70 both radio firmware versions are included in the firmware
package. Depending on the installed variant, the respective radio firmware will
be installed automatically. For GS16, no radio firmware is in the firmware
package included! This must be done manually via SATEL Configuration
Manager using the corresponding "Satel Firmware S-Files" file, refer to Service
Manual "Radio Devices II", chapter "4.3.3 Check and update Satel radio
firmware".
Instrument with built-in Minimum instrument firmware
M3-TR9 HW 3.4 (512kB)
iCG70 iCON 6.61.38
CCD20/21 (slot-in device for iCG60/80) iCON 6.7.0
GS16 SmartWorx 10.65
GS18 Captivate 6.65
Service Manual A small hint with the minimum instrument firmware for the new variants will be
added within the next revision of the corresponding Service Manuals.
Maja Tool With the next revision of "Maja.exe" all variants and firmware's will be shown.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction A new variant of SATEL radio TR4+ (HW 3.8) had to be introduced for GS16, GS18
and iCG70 due to procurement problems of the SATEL processor. The new SATEL
radio has the same performance as the previous one! It can be identified via the
hardware version on the label or via SERIS.
Spare Part 949190 SATEL TR4+ (TA40) 949190 SATEL TR4+ (TA40)
HW 1.7 / 1.8 (1024kB version) HW 3.8 (512kB version)
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service Software In SERIS the different variants can be identified via hardware version.
SATEL Radio The SATEL radio firmware to be used is different for both variants of TR4+.
Firmware
TR4+ hardware variant SATEL firmware
1.7 / 1.8 (1024kB) 07.45.2.5.1.14
3.8 (512kB) 07.58.3.6.0.1
Instrument For GS18 and iCG70 both radio firmware versions are included in the firmware
Firmware package. Depending on the installed variant, the respective radio firmware will be
installed automatically. For GS16, no radio firmware is in the firmware package
included! This must be done manually via SATEL Configuration Manager using the
corresponding sf1 file.
Service Manual The two variants of SATEL TR4+ radio will have the same article number 949190.
Therefore, no update of the service manual is needed.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction A new SATEL radio TR4+ (TA40) has been introduced for GS16, GS18 and
iCG70 due to procurement problems for a component. The SATEL radio has the
same performance as the previous one and does not have to be replaced by the
previous one. The previous SATEL radio M3-TR4 (TA23) is still on stock and
will not be phased out!
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service Software A SERIS update was already released and installed automatically. The new
Radio TR4+ can be identified as follow:
SATEL Radio All new radios TR4+ have SATEL firmware 07.45.2.5.1.14 installed, it is not
Firmware possible to downgrade the TR4+ radio to a lower SATEL firmware version!
Instrument Firmware The new TR4+ radio firmware is released with the following instrument firmware
versions: (No instrument firmware downgrade possible!)
Service Manual The SATEL TR4+ radio will be added to the Service Manuals
"GS10/GS14/GS15/GS16", "GS18" and "iCG70" within the next revision.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction A new Measurement Engine OEM719BL has been introduced for GS16, GS18
and iCG70 to improve the production process. The new measurement engine
has the same performance as the previous one and does not have to be
replaced by the previous one. The previous Measurement Engine OEM719B is
still on stock and will not be phased out!
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service Software A SERIS update was already released and installed automatically. The new
Measurement Engine OEM719BL can be identified by ME Number.
ME Firmware The new Measurement Engine OEM719BL is running from ME firmware 7.804
onwards only! It is not possible to downgrade the OEM719BL to a lower firmware
version!
Instrument Firmware The new OEM719BL Measurement Engine firmware is included in the
instrument firmware package and released with the following instrument
firmware versions: (No Instrument firmware downgrade possible!)
Maja / WinLoad The OEM719BL will be added to "WinLoad" and "Maja" within the next
revision.
Kind regards,
Dietmar Hehle
Central Technical Service GNSS
Introduction We are pleased to inform you about the product announcement of the Leica
GS18 & Leica GS16 UHF GNSS smart antennas and several GNSS product
updates. The primary purpose of this release is to strengthen our GNSS
portfolio and offer our customers an even wider variety of GS sensors to fit their
current and future needs. We are now, for example, adding 4G LTE capabilities
to all our GS18 models.
Service Action Conduct instrument repair according to the latest revision of the corresponding
service manual.
Service Manual The next service manual revision will be available within the next days for
downloading on the service website.
Service Software An update of SERIS will be available within the next days. The feature will be
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Spare Parts With the update of the GNSS products, there are several new spare parts
introduced:
99949188 OEM719BL
949190 SATEL-TR4+
99855730 SATEL M3-TR9 – GS18
99897313 Mainboard no GSM - GS16
873527 SIM/SD IF board no SIM – GS16
804653 GSM bracket – GS16
945658 SIM/SD card cover GS16 (grey) - no SIM logo
OEM719BL
New measurement engine used in high-end GNSS instruments.
For using OEM719BL Captivate v6.50 and SmartWorx Viva v10.50 or higher is
required.
SATEL-TR4+
New radio module in the 400 MHz range replacing the SATEL M3-TR4 radio.
For using SATEL TR4+ Captivate v6.50 and SmartWorx Viva v10.50 or higher
is required.
Service Training All products are included in the existing GS training course. Therefore, for
service-technicians trained on existing GS units don’t require any additional
training.
Phase-Out List We kindly remind you to check the official Phase-Out List on the Service
Website regularly. All instruments and phase-out information are available
there.
Kind regards,
David Urai
Central Technical Service GNSS
Introduction With SmartWorx version 9.0 installed in GS10 and GS15 with ME4, an error message
appears while reading-out the Measurement Engine ME4.
SERIS interrupts reading the PAC number values and ends with a fail.
SERIS
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service No hardware replacement is necessary to resolve this issue. We do not offer any firmware
Actions update for free and cannot accept warranty therefore.
Kind regards,
Dietmar Hehle
Service Engineer
Central Technical Service
Introduction We are pleased to inform about the product release of the new Leica AS11.
For single reference stations, RTK rovers, and RTK or monitoring networks, the
AS11 antenna provides solid performance for a wide range of precision
applications.
This compact antenna combines perfectly with the Leica Viva GS10 & GS25,
Leica GR10 & GR25 and GMX902 receivers.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
To use the AS11 in combination with older software versions the AS11
configuration files must be downloaded from MyWorld and installed manually.
Warranty:
If the instrument does fail during warranty period (one year), the customer will
be served with a warranty swap.
▪ Distribution partners: replace and return the defective instrument by DOA
process.
▪ Selling units: replace and return the defective instrument by DOA process
using the “ZRM-Boomerang” process in SAP.
▪ The defective instrument shall be packed carefully, so that during the
transportation no further damage can occur. If possible, use the original
packing box.
▪ Customer gets new instrument.
▪ Please be informed that we do not accept additional claimed warranty costs.
Non-warranty cases:
▪ No repair process available.
▪ Customers need to purchase a new antenna.
Service Manual The AS11 will be added to the Service Manuals below within the next revision.
▪ GS25-GMxx-GRxx
▪ GS10-GS14-GS15-GS16
▪ GMX900
▪ CS10-CS15
Phase-Out With the release of AS11 the instrument below will be phased-out:
Phase-Out List We kindly remind you to check the official Phase-Out List on the Service
Website regularly. All instruments and phase-out information are available
there.
Kind regards,
Peter Sandner
Central Technical Service GNSS
Phase-Out The latest CS10/CS15 controllers are in production phase-out since 12/2019.
Service phase-out will be approx. in 2024.
The latest GS14 GNSS receivers are in production phase-out since 08/2019.
Service phase-out will be approx. in 2024.
Spare Parts Both the specific spare parts and the general / compatible spare parts will be
provided further on for the next years.
Handling All repair action and full service support will be available for the next years.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phase-Out List We kindly remind you to check the official Phase-Out List on the Service
Website regularly. All instruments and phase-out information are available
there.
Kind regards,
David Urai
Central Technical Service GNSS
Introduction As it was introduced with Service News 26-2019 we will no longer support
SmartWorx Viva versions lower than v5.05.
Service Action No service action needed. No recall or update is necessary with customer
instruments.
The phased-out Processor boards can be ordered until stock lasts, afterwards
the new article numbers must be ordered.
It is still necessary to send back the defective phased-out Processor
boards.
Maintenance dates Always check Maintenance End date and Instrument Firmware version before
performing a board exchange. Ordering a CCP might be needed when replacing
a Processor board.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
David Urai
Central Technical Service GNSS
Service News
No 26-2019
Date 31st July 2019
From Dietmar Hehle
To Service staff / Representatives
Filing Service Manuals for:
GS10-GS14-GS15-GS25
CS10-CS15
Introduction We hereby announce that due to various software improvements all Viva SmartWorx
versions below v5.05 for CS and GS are not supported anymore.
Kind regards,
Dietmar Hehle
Service Engineering
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Introduction It came to our attention, that the thread bolt of the Antenna Holder is a bit
longer as the borehole on some today’s antennas which could damage the
housing. As well it may happen that the screw socket on all active and passive
Antennas get scratched when screwing the Antenna Holder into the
instrument.
Affected Instruments All active antennas (GS, GG, GM, iCG) and all passive antennas (AS,AR,AT)
Solution We introduce 898725 Washer Rubber which must be added to the Antenna
Holder thread as seen on the following pictures.
Service Action Please add the 898725 Washer Rubber to all 777906 Antenna Holders
in your workshop.
Kind regards,
Jörg Niemeyer
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
• 99776292 Processorboard GS
for Viva SmartWorx firmware <5.05
upwards compatible to all newer Viva SmartWorx firmware versions
• 99837905 Processorboard GS
for Viva SmartWorx firmware >= 5.05
upwards compatible to all newer Viva SmartWorx firmware versions
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Solution A new Processorboard GS10/GS15 for the use with OEM729R will be
available as spare part, the needed Viva SmartWorx firmware version 6.00
is already loaded.
Service Manual The new Processorboard will be added into the Service Manual.
Take care that the new Processorboard can only be used if the Maintenance
End is valid for Viva SmartWorx firmware >=6.00!
Kind regards,
Peter Sandner
Central Technical Service
Introduction As already described in Service News 31-2018, various receivers with ME4
and firmware version 4.x stopped tracking satellites on August 4th, 2018.
Because of high count of further enquiries and wrong usage of the already
given information -especially with Viva instruments GR10, GR25, GS10, GS15-
addition detailed instructions will be hand out.
Affected The following instruments can be affected regarding the ME4 tracking issue:
Instruments - GX1200, GRX1200
- ATX900, ATX1230
- GS09
- GS08, GS12
- GMX902
- GR10, GR25
- GS10, GS15
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
ME Identification The ME hardware revision can be read out with the Service Software,
(GX1200, GRX1200, for example:
GMX902)
The firmware for ME4 must be load Update the ME firmware to v6.112 using the GMX902
GMX902 all
separately. Service Software.
RefWorx An old firmware version for ME4 is Update the instrument firmware at least to RefWorx
< 2.50 included in the “GRx.fw” package. version 2.50.
GR10,
GR25
RefWorx A newer firmware version (6.x) for ME4 is
not affected
>= 2.50 already included in the “GRx.fw” package.
Kind regards,
Peter Sandner
Central Technical Service
Introduction After downgrading GS Sensors with Viva Firmware v7.50 or Captivate Firmware
v3.50 to any lower version the mapping of the internal phone modem and the
internal radio module gets lost. Neither a reset nor a firmware update can fix the
problem. Please perform following described procedure below to solve this issue.
Problem in For users: No problems if the affected antenna gets connected with a controller.
practical use For service technicians: SERIS doesn't recognize the internal phone modem and
the internal radio during the readout and/or the testing of these modules.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
Peter Sandner
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
SN3518 - Downgrading GS Sensors with Viva v7.50 & Captivate v3.50_en.docx 2/2 http://service.leica-geosystems.com
Service News
No 31-2018
Date 14th August 2018
From Claudio Cavallaro
To Service staff / representatives
Filing Service Manual
- GPS1200
- GS07-GS08(plus)-GS12-GGxx-GMX9xx
- GS10-GS14-GS15-GS16
- GS25-GRxx-GMxx
- GMX900
Introduction On August 4, 2018, several receivers with ME4 measurement engine with ME
firmware dated from 2009 – 2011 (version 4.00x) stopped to track satellites.
Resetting the ME and/or the SystemRAM does not resolve this issue, a new
ME4 firmware version v6.112 or higher must be loaded.
However, some GNSS receivers lost the communication to the ME and cannot
be updated. In this case, the ME must be recovered in a Service department
using the ME firmware loading fixture art. no. 832856. Please refer to Service
News 03-2017 for details about the fixture.
Affected The following Instruments/Series can be affected regarding the ME4 tracking
Instruments issue:
GX1200 series
ATX1200 series
ATX900/GS09
GS08/GS12
GS10/15/25
GRX1200+GNSS
GR10/25
GM10
GMX902 series (GMX902 GG with ME4 and GMX902 GNSS)
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
After loading firmware v6.112 the ME must be tested by tracking satellites of all
supported constellations until all almanacs have been updated.
Kind regards,
Claudio Cavallaro
Central Technical Service
Service News
No 03-2017
th
Date 10 March 2017
From Peter Sandner
To Service staff / representatives
Filing Service Manuals for:
iCG60-iCG80
CS09-GS09
GS10-GS14-GS15-GS16
GS08(plus)-GS12-GG02plus-GG03-GMX901plus
GPS900
GPS1200
GS25-GMxx-GRxx
MNS1200-MNA950
Zeno20
Introduction We are pleased to announce the introduction of a new test tool for the Measurement
Engines (ME). We offer the "ME Firmware Loading Fixture" (832856) as a stand-alone
test setup. This tool is for resetting, loading and testing of Measurement Engines.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
All information on installing and handling this fixture can be found in the manual
"WinLoadQuickGuide.pdf". The default installation path should be
"C:\Service\WinLoad". There you will find the manual.
Service For service technicians trained on anyone of the GNSS products no additional training
training will be required
Optional During testing it is necessary to check the voltage out of the ME. Therefore you can use
Hardware the Antenna Signal Tester (749448) which you already have for all other GNSS test
setups.
We recommend to use the setup illustrated below in combination with the Antenna
Signal Tester (749448). With this tool it is not necessary to switch between the antenna
cable and the Antenna Signal Tester all the time. An easier handling with less errors is
guaranteed.
566482
SMA/TNC Adapter (pos./neg)
(two pieces necessary)
853371
SMA/TNC Adapter (pos./pos.)
501561
Power Splitter compl.
Kind regards,
Peter Sandner
Service Technician
Central Technical Service
Introduction With the current cookie-can Setup it is possible to create a voltage differential
when connecting directly to an instruments Antenna port. This will permanently
damage the ME, and it will have to be exchanged. This situation can also occur
with instruments with 2 MEs (e.g. iCG82)
Spare part To counter this issue a DC-blocker has to be placed between the splitter and
the Cookie-Can. The part number is :
850906 – DC Blocker
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Gàbor Katona
Service Engineering
Central Technical Service
Introduction A replacement of the current battery compartment seal (Art. No. 733478) is
being introduced. The current seal is as from now on not available anymore.
All current seals Art. No. 733478 have to be scrapped. Scrapping costs
are not covered by Leica.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
There are two small bumps on the new seal. These have to be aligned with the
battery contacts.
Orientation of bumps
Kind regards,
Gàbor Katona
Service Engineering
Central Technical Service
Introduction This service news is to inform on the new upgrade packages available and the
specified upgrade process itself.
Upgrade Packages Available Kits for the GS10, GS14, GS15 and GS25
99841798 – GUS106 GS10 Upgrade with OEM729R
99841799 – GUS107 GS14 Upgrade with OEM719B
99841800 – GUS108 GS15 Upgrade with OEM729R
99841801 – GUS109 GS25 Upgrade with OEM729R
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
The Measurement engines that are removed from the current instruments have
to be sent back to Heerbrugg (via eSpareBack). A refund will be credited upon
return.
Maintenance The upgrade includes a software CCP for the GS sensor. Field controllers,
tablets and total stations to be connected to the upgraded GS sensor must
have SmartWorx Viva v6.00 or Captivate v2.00 or higher installed. Note that
the required CCPs for the CS/TS are not part of the GS upgrade package.
- Multi-frequency
- GLONASS
- Galileo
- BeiDou
No SmartLink fill subscriptions will be available after the upgrade, all other
additional options prior to the Upgrade will still be available.
Unlimited upgrade Please refer to Service News 29-2016 regarding the upgrade packages for
packages Unlimited sales variants.
Service Training For Service technicians trained on the GRxx and GSxx receivers are allowed
to perform the upgrade
Upgrade Process GS A detailed process description, is available in the latest release of the manual
units under section 8 “Upgrades”.
Kind regards,
Gàbor Katona
Service Engineering
Central Technical Service
Introduction This service news is to inform on the process that is needed for GNSS
receivers GS10 / GS14 / GS15 / GS25 Unlimited sales variants that are
already in the market.
Unlimited units GS The Unlimited upgrade packages are available for the following GS sensor :
813740 – GS10 Unlimited receiver
813738 – GS14 3.75G & UHF Unlimited SmartAntenna
813739 – GS14 3.75G & UHF Unlimited SmartAntenna (US/CAN)
813741 – GS15 Unlimited SmartAntenna
813742 – GS25 Unlimited receiver
Unlimited upgrade All customers that have purchased a GS Unlimited as listed above are able to
packages upgrade their units free of charge to the new OEM729R / OEM719B
measurement engine.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
Gàbor Katona
Service Engineering
Central Technical Service
Introduction We are pleased to announce the Leica GS10, GS14, GS15, GS16 and GS25.
This release is bundled with the market introduction and phase out of several
new articles.
Product details, product configurations and article numbers for all models and
related products can be found in the equipment lists
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Service Strategy These instruments can be serviced if the appropriate training has been
complete.
Upgrade Kits The release of these Instruments will also introduce the possibility to upgrade
current instruments with the new OEM7xx Measurement engines
Service software A new service software version will be released at a later date with the service
news considering the upgrade kits
Spareparts With these new instruments the following new spareparts will be introduced :
Kind regards,
Gàbor Katona
Service Engineering
Central Technical Service
Introduction A new HW Revision for the existing Measurement Engines ME4 and OEM628
will be introduced: Rev. 4
The OEM615 and OEM617B are not affected by this hardware revision
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
GR10/GR25/GM10
GS08
GS25
iCG6x
iCG8x
GS10/GS12/GS15
GX1200/ATX1200
GPS900/GS09
Solution From following serial numbers onwards the instruments are equipped with
either the ME4 with new HW Rev.4 (Art.No.: 99842317) or the OEM 628 with
new HW Rev.4 (Art.No.: 99842515).
GR10 - 1704100
GR25 - 1831700
GR25W - 1870250
GM10 – 1725200
GS10 – 1536400
GS15 - 1518300
GS25 - 1833550
iCG60 - 2679120
iCG81 - 2970450
iCG82 – 2923150
GMX900 - 721000
99842317 Measurement Engine ME4 – Rev.4
(Board ref. no.: 766700)
GS10/15/25
ME FW version
Instrument FW version
6.521
5.70 or higher (GS10/15/25 and
CS10/15)
Version 5.70 for a CS10/15 requires
Attention a valid maintenance to load the
firmware.
GS12/GS08
ME FW version 6.421
Instrument FW version 5.70 or higher
Attention Version 5.70 requires a valid
maintenance to load the firmware.
GX1200/ATX1200
ME FW version 6.421
Instrument FW version 8.71 or higher
Version 8.71 for GX1200 and
Attention RX1250 requires a valid
maintenance to load the firmware
GPS900/GS09
ME FW version 6.421
Instrument FW version 8.71 or higher (RX900 and CS09)
Version 8.71 for a RX900/CS09
Attention requires a valid maintenance to load
the firmware
GM10/GR10/GR25
ME FW version 6.521
Instrument FW version 3.22
Version 3.22 for a
Attention GM10/GR10/GR25 requires a valid
maintenance to load the firmware
iCG60
ME FW version 6.521
Instrument FW version 2.5.68 or higher
Version 2.5.68 requires a valid
Attention
maintenance to load the firmware
iCG80 (OEM628)
ME FW included in Instrument Firmware package
Instrument FW version 2.5.76 or higher
Version 2.5.76 requires a valid
Attention
maintenance to load the firmware
GRX1200 Pro
Only ME4 rev.3
The firmware is fully backwards compatible and can be also loaded onto the
ME4 with old HW revisions (Rev. 1 / 2 / 3 ) and onto OEM628.
ME FW Version ME FW Version
ME4 HW Revision
< V6.421 ≥ V6.421
Rev. 3
Rev. 4
For iCG81, iCG82
Kind regards,
Gabor Katona
Service Engineer
Central Technical Service
Reason We would like to inform, that for several processor boards there has been a
hardware change. Therefore, we had to create new article numbers.
It needs to be considered, that the new boards require a specific higher
firmware version, which needs to be in line with the maintenance license
installed on the equipment.
Please find the details below.
Actions for Service The overview table on the next page explains the different board versions.
Centres
Please note, NEW boards only can be used with firmware version V5.05 or
higher! They cannot be downgraded!
In order to ensure the board’s stock availability we strongly request you to:
use a NEW version processor board in case you have a repair unit
with FW V5.05 or higher
consequently return defect boards via the eSpareBack process
* Note:
In future, new boards might have higher board indexes as listed in the table.
Not Affected Boards Not affected are the following boards. They can be used with any firmware
version (restricted by maintenance license).
99 833614 TS16 Application board
99 807394 TS/TM/MS50 Processor board
99 820842 iCON iCx60 Processor board
99 810981 Processor board GS14 - 3.75G
99 810982 Processor board GS14 - 3.75G (USA / CAN)
Expired Maintenance In the moment we try to ensure the availability of both board versions.
License
In case, the old version would be not available anymore, the new version has to
be used.
It may occur, the maintenance license on the equipment does not support the
firmware V5.05. A purchase of a CCP (Customer Care Package incl. SW
Maintenance) would be required then.
Kind regards,
Marco Petermann
Service Engineering
Central Technical Service
Introduction In some rare cases it may happen, that the flex cable of the Slot-in connector for
the GS15 can be damaged by the RF connector. The Slot in module does not
work anymore
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Warranty Service actions in connection with this Service News are covered within the
regular warranty period.
Kind regards,
Dietmar Hehle
Central Technical Service
Introduction For a variety of GS14 variants a BeiDou upgrade kit which contains all required
hardware parts and license keys to fully support the Chinese satellite navigation
system BeiDou is now available:
Upgrade kit The following GS14 instruments can be upgraded to support BeiDou:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
During the order process of the upgrade kit via eShop or SAP, the serial number
of the instrument must be entered.
BuyBack Send back the replaced OEM615B (97833982) via eSpareBack to receive the
BuyBack refund for the upgrade kit.
Upgrade Procedure 1. If necessary, update first instrument firmware at least to version 5.60.
The upgrade kit includes also a firmware maintenance key to load
version 5.60. In that case, do an Auto KeyGen via the service program
and load version 5.60.
Kind regards,
Claudio Cavallaro
Service Engineering
Central Technical Service
Introduction We would like to inform that the exchange module 99766700 ME4 HW Rev. 2.1
and lower, has reached end of life and will be replaced by 99815666 ME4 HW
Rev. 3.0. This service news details the handling of ME4 exchanges in service
and general requirements about instrument and measurement engine firmware.
Also consider Service News 33-2013 for further details for the ME4 HW
Rev.3.0.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Ordered 99815666 ME4 HW Rev. 3.0 are re-labelled with the new number.
Rev 3.0
Actions at Service In case of a ME4 HW Rev. 2.1 exchange to HW Rev. 3.0 might be necessary to
Centers up- or downgrade the loaded instrument firmware or ME FW.
GS10/15/25
Introduction With the launch of the Leica Viva GS14 Unlimited, customers can make a safe
investment with future-proof GNSS smart antennas. Offering a flexible design,
the Viva GNSS sensors can be easily upgraded for maximum performance
whenever needed.
Since August 2014, Leica Viva GS10, GS15 and GS25 receivers fully support
the Chinese BeiDou navigation system. With the release of the latest Leica Viva
GS14 Unlimited Series and Leica Viva GS14 Professional with BeiDou together
with SmartWorx Viva v5.60 release, GS14 now fully supports BeiDou. It can
even provide BeiDou-only and Glonass-only high-precision positioning.
Service Process & The new product is included in the existing GS10/GS15 training course.
Training
GS10/GS15 2.5 days
Service Software The actually released service software for the GS sensors can already be used
to test and repair the GS14 GNSS Unlimited products.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
GPS900/GS09
GM10/GR10/GR25
GMX902
iCG60
The iCG60 is not affected by the migration from ME4 rev 2 to ME4 rev 3.
GRX1200 Pro
Kind regards,
Werner Moser
Service Engineer
Central Technical Service
Kind regards,
Claudio Cavallaro
Service Engineering
Central Technical Service
Introduction With service news 21-2014 we informed you about the new SmartWorx version
5.50. The corresponding firmware for ME4 and OEM615 is 6.403.
Communication Once the latest firmware 6.403 is installed to the ME4/OEM615 they will only be
protocol able to communicate using the Novatel protocol.
Only mainboards with SmartWorx 5.50 (or higher) can communicate with the
Novatel protocol, but also with the LB2 protocol.
All older ME4/OEM615 firmwares (<6.403) can only communicate with the LB2
protocol.
Communication A mainboard with SmartWorx version lower than 5.50 cannot communicate with
issue a measurement engine with version 6.403.
Possible causes of 1.) After exchanging the mainboard on a sensor that had SmartWorx 5.50
fault installed, there is no more communication between the mainboard and
the ME4/OEM615. The reason for this is that exchange boards always
have a SmartWorx version lower than 5.50 preinstalled.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Examples of filenames:
For GS10/15: GS+WinCE_woME_EN.fw
For GS14: GS14+WinCE_woME_EN.fw
For GS25: GS25+WinCE_woME_EN.fw
These files are provided on our service website from now on.
Once the service firmware is installed it’s necessary to load the full SmartWorx
firmware package GS...FW+WinCE…fw 5.50 (or higher) again.
Kind regards,
Jörg Niemeyer
Central Technical Service
Introduction Since we had informed with Service News 11/2012 we still receive
processorboards from GS10 (99776292), GS15 (99776292) and GR10
(99780742) with destroyed components.
This damages can only be caused by using a wrong tool to dismantle the
instrument.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
Dietmar Hehle
Central Technical Service
Introduction With the release of Leica SmartWorx Viva v5.50 there will be two new
measurement engine firmware versions introduced as well. Due to this update
there are a few points that have to be taken into account when using Leica
SmartWorx Viva v5.50. This firmware update will be available for all Viva GS,
CS and smart antennas using Leica SmartWorx Viva.
New measurement There will be two new versions of the measurement engine firmware, version
engine Firmware 6.403 and 6.402 (ME4 and OEM 615). The main difference is the
communication protocol (Novatel / LB2) that is understood by each one :
For example if a measurement engine with 6.403 is mounted into a GS15 with
Leica SmartWorx Viva version <v5.50 there will be no communication with the
measurement engine. Only Leica SmartWorx Viva v5.50 and higher can
communicate with measurement engines set on the Novatel format.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Kind regards,
Gabor Katona
Support Engineer
Central Technical Service
Introduction A new HW Revision for the existing Measurement Engine ME4 will be
introduced: Rev. 3. The reason for this design change is a further improved
rejection of unwanted signal interference.
At the same time also new ME firmware version 6.212 for all ME4 is available.
GS12
GS10/GS15
GM10/GR10/GS25/GR25/GR25W
iCG60
Solution From following serial numbers onwards the instruments are equipped with the
ME4 with new HW revision Rev.3 (Art.No.:99815666):
GS10 ≥ 1535000
GS12 ≥ 1743000
GS15 ≥ 1515000
GS25 ≥ 1833500
GM10 ≥ 1725050
GR10 ≥ 1702500
GR25 ≥ 1831000
GR25 WLAN ≥ 1870100
iCG60 ≥ 2677000
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
In this case new Measurement Engine ME4 Rev.3:
NEW Art.No.: 99815666 (Board ref. no.: 766700) has to be used in case of
exchange.
All Instruments with a lower serial number are equipped with the existing ME4
Rev. 2 (Art.No.99766700).
NEW Article Number:
Actions at The ME4 Rev.2 (Art.No.: 99766700) has to be still used for all instruments with
Service Centers lower serial numbers.
It is not necessary to exchange it during regular servicing!
V 6.212
The firmware is fully backwards compatible and can be also loaded onto the
ME4 with old HW revisions (Rev. 1 / 2 ) and onto OEM615.
ME FW Version ME FW Version
ME4 HW Revision
< V6.212 ≥ V6.212
Kind regards,
Kevin Bless
Central Technical Service
Market Introduction of Leica Viva GS14 GNSS receiver 3.75G & UHF
Introduction We are pleased to release new versions of the Leica Viva GS14 GNSS
receiver, introducing integrated UMTS modems and receive/transmit UHF
radios.
The new GS14 now supports UMTS (3G) networks to be able to get RTK and
Internet connections even in regions where GSM (2G) networks are no longer
operated. With the integrated receive and transmit UHF radio the GS14 now
supports convenient UHF base station operation which increases the
productivity in areas without cell phone network coverage.
Service training The new product is included in the existing GS10/GS15 training course.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Service Manual and The new GS14 Instrument types will be added to the GS10/GS14/GS15
Service-SW Service Manual with next Revision.
Documentation and software are protected with the existing “Viva GS” Dongle-
bit. Only Service Centers with suitably trained technicians will be provided with
the relevant dongle bit.
Spare parts In addition to the existing spare parts of the GS14 – 2G & 2G/UHF variant,
there is a listing of new spare parts for the GS14 3.75G & UHF GNSS
receiver:
Special tools In addition to the already known GPS test setup (Cookie-Can Setup) from
previous GPS Systems, the same special tools as for GS14 – 2G variant are
needed :
Test Setup:
777035 “STB-01” Service Test Box
798007 “STC-06” Service Test Cable
780743 BT Loopback Test box
Special Tool:
804766 Centering Tool for Antenna Element
Kind regards,
Kevin Bless
Central Technical Service
Introduction In the last two months the number of reported cases where the GS10 Battery
Slot #1 does not work has increased. As a result we ask you to control all GS10
on stock and check with multiple batteries (GEB221 and GEB 222) that the
Battery Slot #1 is working correctly. Any GS10 with a faulty Battery Slot may be
returned using the normal processes.
Solution Customer GS10s with a faulty Battery Slot can be repaired by replacing the
battery compartment. This is a temporary solution; we are currently working on
a permanent solution to the issue.
Warranty Service actions in connection with this Service News are covered within the
regular warranty period.
Kind regards,
Kevin Bless
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
http://service.leica-geosystems.com
No 24/2013
st
Date / from 1 August 2013 / K.Bless
To Service staff
Filing Service Manual GS10/GS14/GS15
Introduction We are pleased to announce the new Leica Viva GS14 GNSS receivers.
Designed for performance. The Leica Viva GS14 is the most convenient
GNSS receiver. Thanks to its integrated 3.75 GSM/UMTS and Rx/Tx UHF
modems it is flexible enough to be used in any situation. The compact,
integrated design delivers increased comfort and makes this GNSS receiver a
pleasure to use. Together with the most reliable GNSS RTK the Leica Viva
GS14 delivers you complete confidence and knowledge in your results. The
Leica Viva GS14 expands the Leica Viva portfolio to make it the most powerful
portfolio in the industry.
The following new Leica Viva GS14 articles are available:
• 807531 GS14 3.75G & UHF Performance US/CAN
• 807532 GS14 3.75G & UHF Professional US/CAN
• 807530 GS14 3.75G & UHF Single Frequency US/CAN
st
From August 1 2013 onwards the new Leica Viva GS14 receivers are
available in the USA and Canada only.
Service training The new product is included in the existing GS10/GS15 training course.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Service Manual and The new GS14 Instrument type for USA/CAN will be added to the
Service-SW GS10/GS14/GS15 Service Manual with next Revision.
Revised GS/GR Main service SW is available for download from the CTS
Website.
Documentation and software are protected with the existing “Viva GS” Dongle-
bit. Only Service Centers with suitably trained technicians will be provided with
the relevant dongle bit.
Spare parts In addition to the existing spare parts of the GS14 – 2G & 2G/UHF variant,
there is a listing of new spare parts for the GS14 receivers 3.75G & UHF
USA/CAN:
Special tools In addition to the already known GPS test setup (Cookie-Can Setup) from
previous GPS Systems, the same special tools as for GS14 – 2G variant are
needed :
Test Setup:
777035 “STB-01” Service Test Box
798007 “STC-06” Service Test Cable
780743 BT Loopback Test box
Special Tool:
804766 Centering Tool for Antenna Element
Kind regards,
Kevin Bless
Central Technical Service
Introduction A new coaxial connector will be introduced for the GS14 / GS15 GNSS
receivers. The new revision consists of a small design change of the length.
New instruments are fitted with the new coaxial connector from following serial
number onwards:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Solution In case of a GS14/GS15 repair the new coaxial adapter plug has to be used.
The new coaxial connector can be used instead of the old one for all GS14 and
GS15 instruments.
For other SmartAntennas the old coaxial connector still has to be used.
13.5 mm
13 mm
Kind regards,
Kevin Bless
Central Technical Service
Introduction The design of existing antenna element for GS15 and iCG60 GNSS receiver
has been changed. The reason for this change is the market introduction of new
GS14 GNSS receiver. Essentially, the new revision consists of a small design
change of the mounting holes for GS14 GNSS receiver.
Affected parts All GS14, GS15 and iCG60 instruments which are produced since December
2012 are equipped with new antenna elements (Revision Index 4).
Solution Antenna elements with revision index 3 on service stock levels can be only
used for GS15 and iCG60 instruments.
For GS14 GNSS receiver the new antenna element with revision index 4 must
be used. In case of repair verify that the correct version will be assembled.
The new antenna elements (Rev 4) are fully backward compatible and can be
used instead of old antenna elements (Rev 3) for GS14, GS15 and iCG60
instruments.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Old antenna element – Rev 3:
for GS15 and iCG60 only
Kind regards,
Kevin Bless
Central Technical Service
Introduction We are pleased to announce the new Leica Viva GS14 GNSS receiver.
Designed for performance. The Leica Viva GS14 is the most convenient GNSS
receiver. Thanks to its integrated GSM and UHF modems it is flexible enough
to be used in any situation. The compact, integrated design delivers increased
comfort and makes this GNSS receiver a pleasure to use. Together with the
most reliable GNSS RTK the Leica Viva GS14 delivers you complete
confidence and knowledge in your results. The Leica Viva GS14 expands the
Leica Viva portfolio to make it the most powerful portfolio in the industry.
Service training The new products are included in the existing GS10/GS15 training course.
Service Manual and The revised GS10/GS15 Service Manual and revised GS/GR Main service SW
Service-SW will be available for download from the CTS-Website.
Documentation and software are protected with the existing Viva GS Dongle-
bit. Only Service Centers with suitably trained technicians will be provided with
the relevant dongle bit.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Spare parts Below, there is a listing of recommended spare parts for the GS14 product:
Gaskets
791508 Housing gasket GS14
733478 Battery cover gasket GS14
Special tools In addition to the already known GPS test setup (Cookie-Can Setup) from
previous GPS Systems, the following special tools are needed :
Test Setup:
777035 Viva GNSS Testbox
798007 STC-06
780743 BT Loopback Testbox
Special Tool:
804766 Centering Tool for Antenna Element
Kind regards,
Claudio Cavallaro
Central Technical Service
Introduction We are very pleased to announce the new visionary Leica AR20 3D Choke
Ring Antenna. The new and unique 3D (inside) design brings unmatched
multipath rejection across all GNSS frequency bands and improved phase
centre stability. The AR20 antennas is designed for all reference station and
monitoring applications, and is the ideal choke ring antenna for Network
RTK.
Features of the new AR20 Antenna:
New 3D (inside) design for improved multipath rejection across all
GNSS frequency bands.
Phase centre offsets within 1mm, phase centre repeatability within
1mm
New even more robust choke ring surface treatment
Optional conical radome
Exchange Modules Should an antenna become defective or develop malfunctions, the complete
Antenna has to be exchanged with the following module:
Claudio Cavallaro
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
SN3612_Market Introduction AR20 Choke Ring Antenna_en.doc http://service.leica-geosystems.com
No 11/2012
Date / from March 01, 2012 / BLKE - 4124
To Service Staff
Filing Service Manual GS10/GS15 & GS25/GR10/GR25
Issues We have some problems with the following processorboards due to an existing
socket spanner:
Component 1: Component 2:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
http://service.leica-geosystems.com
Component 3: Bluetooth Antenna Connector
Cause By using of the following existing special tool, the components on the boards
will be destroyed:
Solution The service tool has to be changed. There are two possibilities to solve this
issue:
Order the new Socket spanner and waste the old one, the article
number is the same: 746045 Socket spanner #5.5 reworked
-> We reworked all socket spanners on stock.
or
Rework the existing Socket spanner at your workshop by the attached
drawing with new dimensions.
Kind regards,
Kevin Bless
Central Technical Service
SN1112_GS_GR_Processorboard_Destroying_components_en.doc 2/2
0 .2 x 4 5 °
1 0
-0 .1 7 .5 0
7 .2 0
P O S . P ie c e s M E D e s c r ip tio n
a g e s .
th e rs
o r ity .
n ts
1 0 1 p ie c e 7 7 7 0 9 5 s o c k e t s p a n n e r # 5 .5
2 0 B R C 4 2 6 3 4 0 / 5 .5
g it to o
s s a u th
3 0
t o f d a m
e c o n te
4 0
x p re
g iv in
m e n
o f th
5 0
p a y
a n d
tio n
o u t e
6 0
ith
ic a
n t,
th e
7 0
: :
u n
to
m e
n w
8 0
D a te : T e l. / V is . : C h a n g e s :
9 0
1 0 0 c re a te d : 0 2 .0 9 .2 0 0 9 4 6 6 4 -R A Y P 0 9 .0 2 .2 0 1 2
D im e n s io n s : m m S c a le 5 :1
o r c o m m
fo r b id d e
r e L ia b le
th is d o c u
1 1 0 r e le a s e d : 0 2 .0 9 .2 0 0 9 3 7 0 5 -M W E 4 1 2 4 -B L K E D e s ig n a t io n : S o c k e t S p a n n e r # 5 .5 re w o rk e d 7 4 6 0 4 5
o f
a re
u s e
rs a
1 2 0 A re a A D O C -C O D E E D V -/A R T .-/P R O J E C T N O . S T A T U S
th e
n d e
y in g
e o f,
1 3 0
C o p
a n d
th e r
O ffe
1 4 0 4 F K Z 7 4 6 0 4 5 V 3
1 5 0
0 2 5
No 27/2011
Date / from 16. Dec. 2011 / BLKE
To Service staff
Filing Service Manual GPS1200
Introduction This Service News explains the new process for ordering Exchange Modules
of the AR25 / AT504 Choke Ring Antenna.
From now onwards there are two different Exchange Modules for the AR25
Choke Ring Antenna which can be ordered:
Exchange procedure Should an antenna become defective or develop malfunctions, the complete
antenna has to be exchanged with the following modules. The defective
antenna will require to be returned to Heerbrugg.
If you return an AR25 with Revision lower than 3.0 (e.g. Rev. 2.0), it will
exchanged with an AR25 Revision 3.0.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
http://service.leica-geosystems.com
It is not possible to exchange:
AR25, Revision 3.0. or lower version with an Exchange
AR25 Revision 4.0.
Upgrades Upgrade for AT504 to AT504GG is available, see Service News 33/2006
No upgrades are offered from: AR25, Revision 3.0 to
AR25, Revision 4.0.
Kind regards,
Kevin Bless
Central Technical Service
SN2711_Exchange_modules_AR25&AT504.doc 2/2
No 16/2010
Date / from 26. July. 2010 / Claudio Cavallaro
To Service staff
Filing Service Manual GS10/15
Introduction It happens that the SLG1 does not proper register to a network, when inserted
into a GS15 . The device is powered but maintains in the "search" mode to find
a telecommunication provider and is not useable therefore. As soon then the
SLG1 is rebooted, the problem might be solved and the device is ready in a
network and ready for dialing. But again if the SLG1 is powered off again and
down for a certain time, after that the problem again appears .
New Firmware Driver and new Firmware for the SLG1 are available for download from the
service website.
Update procedure Attached to this service news is a description which tools are required, how to
install the necessary driver and upload the firmware.
Kind regards,
Claudio Cavallaro
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
SN1610_New Firmware 08.01.107 for SLG1_en.doc http://service.leica-geosystems.com
SLG: Driver installation and Firmware update
1 Tools ................................................................................................................................................ 2
2 USB driver installation ...................................................................................................................... 3
3 Update SLG Firmware...................................................................................................................... 5
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
Phone. +41 71 727 31 31
SN1610_Attachement_en.doc www.leica-geosystems.com
1 Tools
!#
"#
SN1610_Attachement_en.doc 2/5
2 USB driver installation
Download the latest driver for the SLG from the service website.
Connect the USB cable to the PC and follow the instruction below.
1. Choose “Install from a list or specific location (Advanced)” and press Next.
2. Select “Search for the best driver in these locations” and check “Include this location in the search:”
checkbox, then click “Browse”. Select the directory containing usb drivers then click “OK” and “Next”
SN1610_Attachement_en.doc 3/5
The procedure “Found new hardware wizard” restarts again to install other virtual com ports. Repeat step
1 and 2 until all needed driver are installed.
After a successful installation the following virtual com ports and device are available (Device Manager).
Control Panel ! Administrative Tools ! Computer Management ! Device Manager
Device
SN1610_Attachement_en.doc 4/5
3 Update SLG Firmware
Download the latest Firmware for the SLG from the service website.
Connect the USB cable to the PC and follow the instruction below.
Choose the correct Port: Virtual com port for “Telit Diagnostics Interface” (in that case COM10)
Control Panel ! Administrative Tools ! Computer Management ! Device Manager
Press Download.
SN1610_Attachement_en.doc 5/5
No 05/2010
Date / from 16 March 2010 / RAYP 4664
To Service staff
Filing GS10/GS15 Service Manual
Introduction The purpose of this Service News is to inform about a wrong reassembly
instruction in the GS10/GS15 Service Manual. The wrong instruction regarding
the cable laying of the internal GSM and UHF cable on GS15 SmartAntennas is
on page 14 of chapter 9.
The HF cable for the internal GSM antenna has to be laid with a “loop”.
Then, the HF cable for the UHF antenna ! has to be laid through this loop.
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/2 http://service.leica-geosystems.com
Rectified instruction The wrong instruction will be rectified within the next revision of the Service
Manual as follows:
The HF cable for the internal GSM antenna has to be laid with a “loop”.
Then, the HF cable for the UHF antenna ! has to be laid behind this loop.
Measures to take in Lay both HF cables for GSM und UHF according to this Service News and not
Service Centers to the description in the Service Manual (Edition 11/09) when reassembling a
GS15 SmartAntenna.
Please note, the HF cables are laid correctly on all GS15 SmartAntennas!
Therefore, there is no need to recall products to re-lay the HF cables nor is it
necessary to re-lay the HF cables as a part of regular servicing. This issue
deals just with a wrong instruction in the Service Manual.
Kind regards,
Patrick Rayero
Central Technical Service
SN0510_GS15_Cable_laying_of_internal_HF_cables_en.doc 2/2
No 03/2010
Date / from 05. March. 2010 / Claudio Cavallaro
To Service staff
Filing Service Manual GPS1200; GS10/GS15
Kind regards,
Claudio Cavallaro
Central Technical Service
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
SN0310_Market Introduction AR10 GNSS Reference Station Antenna_en.doc http://service.leica-geosystems.com
No 45/2009
Date / from 18. November 2009 / C.Cavallaro
To Service staff
Filing
Introduction We are proud to announce Leica Viva, a new generation surveying system that
combines the latest state-of-the-art technologies into an unrivalled portfolio of
total stations, GNSS receivers, controllers and onboard software.
With the associated slogan Leica Viva “…let us inspire you” Leica Geosystems
expresses its long and unsurpassed experience of innovation and inspiration in
the surveying market providing customers with the right system to make their
measuring visions come true.
Leica Viva Field Controllers – rugged with the world’s first integrated antenna.
The new Leica CS10 and CS15 are rugged field controllers that can be used for
both GNSS measurements and with total stations. Leica Viva controllers allow
an easy equipment setup with the unique “Snap&Go” connection system. The
new Leica intenna technology introduces a world first by fully integrating the
communication antennas into the controller housing.
CS15
CS10
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Switzerland
1/3 http://service.leica-geosystems.com
Service training We offer two new Training Courses for the GS10/GS15 and CS10/CS15.
GS10/GS15 2 days
CS10/CS15 2 days
The Service Training course are schedule and published on the Service
Website.
Service Manual and The new GS10/GS15 and CS10/CS15 Service Manual (Edition 11/09) and new
Service-SW service software GS Main and CS Main will be available for download from the
CTS-Website.
Separate Viva GS and Viva CS dongle-bit protects Documentation and
software. Only Service Centers with suitably trained technicians will be provided
with the relevant dongle bit.
Spare parts Below, there is a listing of recommended spare parts for the GS and CS
products:
GS10/GS15
(99) 776292 Processorboard GS tested
(99) 766700 ME4
Gaskets
767203 Housing gasket GS15
769360 Battery cover gasket GS15
769037 Gasket for GS15 Slot-In cover
732863 Housing gasket GS10
736854 Gasket battery chamber GS10
732917 Washer for front panel GS10
CS10/CS15
(99) 773914 Processorboard CS15 tested
(99) 773917 Processorboard CS10 tested
773916 Upper housing CS10 cpl.
773913 Upper housing CS15 cpl.
Gaskets
765415 Housing gasket CS15
765416 Housing gasket CS10
766819 Battery compartment sealing
766835 Connector module sealing
765807 Sealing ring washer
GS10/GS15
777997 Slot-In Test Dummy
767791 QN/TNC Adapter
749448 Antenna Signal Tester
772195 SLx Testbox
566482 SMA/TNC Adapter (pos./neg.)
777906 GS15 Holder
CS10/CS15
777247 WL Loopback Box
777243 CS10 Test Dummy
777245 CS15 Test Dummy
776100 USB 2.0 cable “A to mini A”
776830 CS10/CS15 Power Cable
778175 D-Sub shorting plug female
Kind regards,
Claudio Cavallaro
Central Technical Service
Brochures
User Manuals
SSP Brochure
Technical Data
Equipment Lists
Measurement Engine
Housing and MMI
LNA Board
Radio Module
Port 3 Serial interface for data, Power out, Port 1 USB and Serial interface for data
8pin LEMO (CS field Controller), 8pin LEMO
PWR Power port, 5pin LEMO, dual input QN Connector External Radio Antenna, only for models
GNSS GNSS Antenna port with UHF radio, no +5V
Port 1 USB and Serial interface for data
(CS field Controller), 8pin LEMO
Port 2 Serial interface for data, Power out,
8pin LEMO
Batt A Battery compartment A including SD
card compartment
Batt B Battery compartment B
Lemo Port P1 Lemo Port P2 and P3
Lemo Port P1
Lemo Port P1 Lemo Port P2
Connector Board:
The connector board provides:
Power Supply for the Typhoon Board and ME.
Input voltage range is 10.5... 28V.
ON/OFF & Function-Button Interface
LEDs for status indication
(Power, BT-status, SD card status, Tracking).
Input-/ Output Interface
Bluetooth:
Bluetooth is provided for wireless communication to
the CS10/CS15 Viva field controllers.
Batteries:
The batteries are used if no valid external voltage is
applied on any of its connectors.
Data Storage:
To save the data you can use an SD card.
Processor board:
Power Supply for the OEM615 / OEM719. Input
voltage range is 10.5... 28V.
ON/OFF & Function-Button Interface
LEDs for status indication
(Power, BT-status, SD card status, Radio status,
Tracking)
RTK Radio:
Internal SATEL radio OEM20 / OEM22 with an
external antenna. No +5V Voltage on External
Antenna connector (QN).
Phone:
Internal 2G / 3.75G module assembled. A SIM card
can be inserted in the battery compartment.
Bluetooth:
Bluetooth is provided for wireless communication to
the CS10/CS15/CS20 Viva field controllers.
Battery:
The battery is used if no valid external voltage is
applied on it connector.
Data Storage:
To save the data you can use a micro SD card.
Processor board:
Power Supply for the ME. Input voltage range is
10.5... 28V.
ON/OFF & Function-Button Interface
LEDs for status indication
(Power, BT-status, SD card status, Radio status,
Tracking)
Filterboard:
Change between the different antennas: GSM/GPRS/
UMTS, UHF and RTK Radios with an external
antenna. +5V Voltage on External Antenna connector
(QN).
Bluetooth:
Bluetooth is provided for wireless communication to
the CS10/CS15 Viva field controllers.
Batteries:
The batteries are used if no valid external voltage is
applied on any of its connectors.
Data Storage:
To save the data you can use an SD card.
The Service Software (SERIS) is available for downloading on the Start SERIS and choose your instrument group and family.
“myServiceProducts” website. Once installed, SERIS Launcher will load all Read equipment number automatically or set it manually.
updates by itself. Create and open the new service job.
Menu Description
Initial Read-out Reads out instrument data (e.g. FW versions,
installed applications and languages etc.).
Restore
Customer data will be restored back to the instrument
from the “*.zip” file located on the SD card, this also
will include the keys.
Instrument Software The instrument software can be loaded either via
SERIS or the Webserver.
Menu Description
AuthCode If an exchange/upgrade of the Measurement Engine
(OEM) was necessary, a new AuthCode will be down-
loaded from SAP database and set on the OEM. Menu Description
Radio Module If the communication to the SATEL radio module does Outgoing Test Can also be used as “Incoming Test”.
not work during the Outgoing Test (caused by wrong Can be run through on “Auto” mode.
settings / Baud Rate on the radio) a connection with Final Read-out The same procedure as the “Initial read out” but with
default settings can be tried here. the final values of firmware, keys, apps, languages.
Processor Board An own workflow for setting values in case of a Must be performed to finish the service job “success-
Exchange processor board exchange. fully”.
Service technicians may ask for help when having difficulties during repair or may
report a potential error in SERIS. For this a support case can be created directly
out of SERIS.
Tab Description
General Fill out your name and your E-Mail address.
informations Give your description inside the comment area.
Other general information, such as SERIS version, service
job data and instrument data will be filled out automatically.
Screenshot With pressing the button “Failure Report” a screenshot is taken
automatically to see potential error messages etc.
Measurement Engine
Housing and MMI
LNA Board
Radio Module
Description
Data (Leica GNSS raw data and RINEX data) can be recorded on the micro SD
card.
Memory Device
a
d
b e
a b c d e f g h i j k l
a) Bluetooth antenna
a) QN-connector for external UHF antenna, only for models with UHF radio
b) Guide rail for clip-on-housing of a device (available on both sides)
b) Battery compartment with micro SD and SIM card slot
c) Function button
c) LEDs, ON/OFF button and Function button
d) ON/OFF button
d) LEMO port, serial and USB
e) LEMO port P3
e) Mechanical Reference Plane (MRP)
f) Power port
g) Antenna port
h) LED indicators
i) Battery compartment A including SD card compartment
j) Battery compartment B
k) LEMO port P2
l) LEMO port P1 including USB port
a
e
b
f
3. With the Leica logo facing upwards, slide the battery into the battery 2. Remove the cover from the battery compartment.
compartment and push upwards so that it locks into position. 3. With the battery contacts facing upwards, slide the battery into the cover of
4. Close the cover of the battery compartment and tighten the screw. the battery compartment.
5. To remove a battery, loosen the screw to open the cover of the battery 4. Push the battery upwards so that it locks into position.
compartment. 5. Insert the cover of the battery compartment into the compartment and push
6. Push the battery slightly in and at the same time downwards. This releases the slide fastener in the direction of the arrow with the close-lock symbol.
the battery from its fixed position. 6. To remove a battery, push the slide fastener of the battery compartment in
7. Pull out the battery. the direction of the arrow with the open-lock symbol and remove the cover.
8. Close the cover of the battery compartment and tighten the screw. 7. Push the battery slightly upwards and at the same time pull out the bottom
part of the battery. This releases the battery from its fixed position.
8. Remove the battery.
Step Description
1. Push the slide fastener of one of the battery compartments in the direction
of the arrow with the open-lock symbol.
2. Remove the cover from the battery compartment.
3. With the battery contacts facing upwards, slide the battery into the cover of
the battery compartment.
4. Push the battery upwards so that it locks into position.
5. Insert the cover of the battery compartment into the compartment and push
the slide fastener in the direction of the arrow with the close-lock symbol.
6. To remove a battery, push the slide fastener of one of the battery compart-
ments in the direction of the arrow with the open-lock symbol and remove
the cover.
7. Push the battery slightly upwards and at the same time pull out the bottom
part of the battery. This releases the battery from its fixed position.
8. Remove the battery.
1.
The SD card is inserted into a slot inside the battery compartment A of
the instrument.
Open the cover of battery compartment A. Refer to "Battery for GS14 /
1.
The SD card is inserted into a slot inside the battery compartment of the
instrument.
Push the slide fastener of battery compartment in the direction of the
GS16" on page 8. arrow with the open-lock symbol.
2. Insert the card firmly into the slot until it clicks into position. 2. Remove the cover from the battery compartment.
3. Close the cover of battery compartment A and tighten the screw. 3. Press the latch of the SIM/micro SD card cover and remove the cover.
4. To remove the card, open the cover of battery compartment A. 4. Slide the micro SD card with the logo facing upwards firmly into the slot
5. Gently press on the top of the card to release it from the slot. until it clicks into position.
6. Remove the SD card.
7. Close the cover of battery compartment A and tighten the screw.
1.
The SIM card is inserted into a slot inside the battery compartment of the
instrument.
Push the slide fastener of battery compartment in the direction of the
1.
The SD card is inserted into a slot inside the battery compartment 1 of
the instrument.
Push the slide fastener of battery compartment 1 in the direction of the
arrow with the open-lock symbol. arrow with the open-lock symbol.
2. Remove the cover from battery compartment. 2. Remove the cover from battery compartment 1.
3. Press the latch of the SIM/micro SD card cover and remove the cover. 3. Slide the card firmly into the slot until it clicks into position.
4. Push the SIM card holder in the direction of the OPEN arrow and flip it up. 4. Do not force the card into the slot. The card should be held with the
5. Place the SIM card into the SIM card holder, the chip facing the connec- contacts upwards and facing the slot.
tors inside the slot - as shown on the SIM/micro SD card cover. 5. To remove the card, push the slide fastener of battery compartment 1 in
Press the SIM card holder down. the direction of the arrow with the open-lock symbol and remove the
6. Push the SIM card holder in the direction of the LOCK arrow to close. cover.
6. Gently press on the top of the card to release it from the slot.
7. Remove the SD card.
8. Insert the cover into battery compartment.
6.3.1 MMI
ON/OFF button GS10 / GS15
MMI GS10 Button Function
b a ON/OFF If GS10/GS15 already off:
Turns on GS10/GS15 when held for 2s.
a) ON/OFF button
b) Function button While the GS10/GS15 is booting all three
battery LEDs are lighted. Once the GS10/GS15
has started, the normal LED behavior starts.
If GS10/GS15 already on:
Turns off GS10/GS15 when held for 2s.
a b
ON/OFF button GS14 / GS16
a) ON/OFF button
b) Function button Button Function
ON/OFF If GS14 already off:
Turns on GS14 when held for 2s.
a b
a) ON/OFF button
The Storage, Position, RTK Base and RTK
Rover LEDs shine red, both Power and the
Bluetooth LEDs shine yellow and then are
turned off.
b) Function button
The GS10/GS15 GNSS instrument has Light Emitting Diode indicators. They indi- Description of the LEDs
cate the basic instrument status. IF the is THEN
GS15 a b c d e f green Bluetooth is in data mode and ready for connecting.
Bluetooth
purple Bluetooth is connecting.
LED
blue Bluetooth has connected.
off no SD card is inserted or GS10/GS15 is switched off.
green SD card is inserted but no raw data is being logged.
flashing green raw data is being logged.
Storage flashing yellow raw data is being logged but only 10% memory left.
LED flashing red raw data is being logged but only 5% memory left.
red SD card is full, no raw data is being logged.
GS10 ae f no SD card is inserted but GS10/GS15 is configured
fast flashing red
to log raw data.
no satellites are tracked or GS10/GS15 is switched
off
off.
a) Bluetooth LED less than four satellites are tracked, a position is not
Position flashing yellow
b) Storage LED yet available.
c) Position LED LED
yellow a navigated position is available.
b d) Power LEDs
flashing green a code-only position is available.
c e) RTK Base LED
f) RTK Rover LED green a fixed RTK position is available.
d
The GS14 /GS16 GNSS receivers have Light Emitting Diode indicators. Description of the LEDs
They indicate the basic instrument status. IF the is THEN
GS14 / GS16 Bluetooth green Bluetooth is in data mode and ready for connecting.
a b c d e f LED blue Bluetooth has connected.
no micro SD card is inserted or GS14/GS16 is
off
switched off.
Micro SD card is inserted but no raw data is being
green
logged.
Storage
flashing green raw data is being logged.
LED
flashing red raw data is being logged but only 5% memory left.
Micro SD card is full, no raw data is being logged or
red no micro SD card is inserted but GS14/GS16 is
configured to log raw data.
no satellites are tracked or GS14/GS16 is switched
off
off.
less than four satellites are tracked, a position is not
Position flashing yellow
yet available.
LED
yellow a navigated position is available.
flashing green a code-only position is available.
green a fixed RTK position is available.
a) Bluetooth LED
battery is not connected, flat or GS14/GS16 is
b) Storage LED off
switched off.
c) Power LEDs
Power green power is 20% - 100%.
d) Position LED
LED
e) RTK Base LED power is 5% - 20%. The remaining time for which
(active
f) RTK Rover LED red enough power is available depends on the type of
battery)
survey, the temperature and the age of the battery.
fast flashing red power is low (<5%).
Step Description
1. Start the PC.
2. Insert the Leica Viva Series DVD or download the driver from the
“myServiceProducts” website.
3. Run the “Setup_Leica_USB_XXbit.exe” to install the drivers necessary
for Leica instruments. Depending on the version (32 bit or 64 bit) of the
operating system on your PC, you have to select between the following
three setup files:
SetupLeica_USB_32bit.exe
SetupLeica_USB_64bit.exe
SetupLeica_USB_64bit_itanium.exe
The setup has to be run only once for all Leica instruments.
4. The “Welcome to InstallShield Wizard for Leica ... drivers” window
appears.
Ensure that all Leica instruments are disconnected from your PC before
you continue.
5. Click “Next>”.
6. The “Ready to Install the Program” window appears.
7. “Installing...”
The drivers will be installed on your PC.
8. The “InstallShield Wizard Completed” window appears.
9. Click “Finish” to exit the wizard.
GS10/GS15:
Step Description
1. Start the PC.
2. Connect the GS instrument via the GEV234 cable or according to the test
setups shown in "Repair Process" chapter 7.
3. Turn on the instrument.
4. The “Found New Hardware Wizard” starts up automatically.
5. Check “Yes, this time only” Next>.
6. Check “Install the software automatically (recommended).” Next>.
The driver for Remote NDIS based LGS GS Device (GS10/GS15) will
be installed.
7. Finish.
8. The “Found New Hardware Wizard” starts up automatically for
a second time.
GS14 / GS16: 9. Check “Yes, this time only” Next>.
10. Check “Install the software automatically (recommended)” Next>.
The driver for LGS GS USB Device (GS10/GS14/GS15/GS16) will be
installed on your PC.
Description
The Webserver is a web-based tool to view and configure the status of the
GS10/GS14/GS15/GS16 GNSS instruments. Also updating the firmware, settings
Attention:
It is not possible to communicate with a CS10/CS15/CS20 Field
Controller via Bluetooth when connected to the Webserver!
keys, etc. can be carried out via the Webserver.
The Webserver application is integrated into the firmware and cannot be deleted.
Step Description
1. Start the PC and turn the GS GNSS instrument on.
2. Connect the GS instrument via the GEV234 cable or according to the test
setups shown in "Repair Process" chapter 7.
3. Start the web browser of your PC.
4. Type in http://192.168.254.2 and press enter to access the Webserver of
GS instrument.
Measurement Engine
Housing and MMI
LNA Board
Radio Module
+
+
2x
+
+
+
software.img
Webserver
Webserver
SERIS
SERIS
Boot/EFI
WinCE
Add-on
(SmartWorx)
Webserver
ME
Step Description
versions will be replaced, refer to Bootloader Service Manual.
1. Download and decrypt the package
5. One of the two processes mentioned before must be followed “Viva Firmware loading without ME/OEM FW”
(loading firmware again via SERIS or Webserver). from the “myServiceProducts” website (instrument “Tools”).
2. Copy the “DBG” folder in the root directory of the SD card.
This subchapter gives an overview about the definition of the different key types. With the Auto KeyGen in SERIS, all keys can be downloaded from the SAP
database and set on the instrument automatically.
Key type Description In addition, single keys or external key files can be loaded manually.
Instrument key Instrument key sets the instrument type and the
serial number on the instrument.
Maintenance key Maintenance key sets the expiry date of the software mainte-
nance.
The release date of the firmware must be lower than the
maintenance end date, otherwise it is not possible to load the
firmware.
Release date
Hardware Option Hardware option keys are used to activate the installed
hardware, e.g. Antenna Element.
Software Option Software option keys are used to activate software options,
e.g. Glonass option, Purchase Mode, Position Rate, …
After loading the OEM AuthCode, the unlocked options must be activated via
Webserver:
Step Description
1. Start a web browser and enter address http://192.168.254.2
2. Go to “Instrument” “Satellite settings”.
3. Activate all available satellite systems “”.
4.
Configure radio
Refer to service manual “Radio Devices II,
chapter 4 - SATEL Config Manager”.
Use the SATEL Config Manager to load the local
Service Config File for M3-TR4 to the internal radio.
5. Initial Read-out Perform an Initial Read-out to synchronize data with
the SAP database.
6. RadioTest Perform radio tests as necessary.
7. Range test In case of customer complaint, perform an outdoor
test to verify radio range 6. Test Perform tracking tests as necessary to check the
function of the OEM.
When connecting the CGR Testbox, make sure to connect the on both radios
USB first, before connecting the power supply. Close SATEL Config Manager
Voltage differentials can be caused and will damage the USB
2. Test UHF radio Run the test according to SERIS instructions.
hub, if this sequence is not followed.
GS10
Core board stack is blocked due to
Processor Board key can’t be generated in GS14 send the Initial Read-Out to
it is being used in another equip-
KeyGen GS15 service.support@leica-geosystems.com
ment.
GS16
Without valid maintenance-end date:
Downgrade instrument firmware to SmartWorx Viva 8.0.
Perform the Final Read-Out to PASS the Outgoing Test.
Measurement Engine PAC values can not
GS10 Upgrade instrument firmware to SmartWorx Viva 9.0.
be read out when SmartWorx Viva 9.0 is SmartWox Viva 9.0 software issue
GS15
installed
With valid maintenance-end date:
Update to the latest instrument firmware >9.0.
Perform Final Read-Out.
Connect with Bootloader Menu and check if the following settings
are correct:
go to menu ‘e) Image options’
d) Add-on images enabled: enabled
e) Add-on images jobs: not skipped
GS10
Rover LED off, GS14 Bootloader Add-on image jobs
No connetion to SERIS GS15 skipped, refer to FAQ 02-19
GS16
GS10
GS14
SNo. <3129000
GS14
SNo. >=3129000
GS15
GS16
The internal mapping of the modules (phone modem and radio module) is different To let SERIS communicate with the internal modules the mapping must be
between “using mode” and “testing mode”. changes to “testing mode”, for this go to “Adjust” and run the both steps :
As soon as the user connects a controller with the antenna the modules will be Set Cellular Mobile type
mapped automatically to “user mode”. Set Radio Type
The internal ports needed for the communication with SERIS are blocked then
by the internal communication.
Step Description
1. Go to “Adjust” and use the step “Adjust Radio Module”
(no read-out before port-forwarding to the radio module).
2. Try also all other Baud Rates, not only the mentioned ones in the test
description.
If the read-out of the Radio module brings values “0” for there are three known Change back the internal Baudrate of the Satel radio module,
solutions. refer to Radio Devices II Service Manual,
chapter 4 “Satel Config Manager”..
An instrument reset was executed before and the adjustment was incomplete
or unsuccessful afterwards.
2. To find out which COM port is the instrument and which is the reference
radio, it is helpful to disconnect the connection one by one and observe
the ports disappearing.
3. Enter the corresponding COM ports into the calibration values in SERIS.
The procedures described in this chapter have to be General tools for disassembly/reassembly:
used for replacing of internal modules of the following
receivers: Install of self tapping screws: Make
sure to first turn the screws counter-
clockwise, until the screws lock into the
520716 Torque screwdriver “10 … 120Ncm”
520717 Torque screwdriver “100 … 600Ncm”
"9.1 GS10 GNSS Receiver" on page 2 existing threads, to avoid possible 712234 Torx insert “T8/50”
wear out of the thread. 740255 Torque screwdriver bit with ball head
746045 Socket spanner #5.5 reworked
180256 Side cutter small
520893 Adapter 6kt to 4kt (1/4”)
740535 Lemo bit for torque
Caution:
ESD (Electro Static Discharge). Make
sure your workbench has the neces-
sary precautions against ESD.
Disassembly: Reassembly:
6x
Double-check that the housing
gasket is correctly placed in its
groove of the front plate assembly.
Slice cable tie carefully up. Install cable tie to align Bluetooth cable and
antenna cable at the shock frame,
tighten it to max 34 N
(level 1 with 937964 Cable Tie Pliers).
6x
8x
2x
Remove 6 nuts ,
Install 6 M3 nuts (161185) ,
using socket spanner 746045.
torque to 60Ncm, using socket spanner 746045.
Remove shock frame .
6x
3x
6x
Unlock 3LED flex by squeezing the flex carefully
in direction . Install 3LED flex by squeezing the flex carefully
Remove 3LED flex . in direction .
Remove battery chamber gasket . Install battery chamber gasket .
Remove locking washer and washer . Install washer and locking washer on
Remove M5 screw fastener , bearing seat M5 screw fastener .
and bearing seat . Install bearing seat on M5 screw fastener .
Install bearing seat .
2x
The procedures described in this chapter have to be General tools for disassembly/reassembly:
used for replacing of internal modules of the following
antennas: Install of self tapping screws: Make
sure to first turn the screws counter-
clockwise, until the screws lock into the
520716 Torque screwdriver “10 … 120Ncm”
520717 Torque screwdriver “100 … 600Ncm”
"10.1 GS14 / GS16" on page 2 existing threads, to avoid possible 742998 Torx Insert “T6/50”
wear out of the thread. 777609 Torx insert “T8/90”
779262 Torx insert “T10/50”
740535 Lemo bit for torque
Disassembly: Reassembly:
18x
6x
5x
Add WinCE Label as shown in
picture!
Double-check first that the O-Ring of
both connectors are properly fitted
and dust caps do not get squashed!
Disconnect 2 flex cables .
Disconnect HF cable GSM antenna .
2x
5x
Add WinCE Label as shown in
picture!
2x
5x
Add WinCE Label as shown in
picture!
Double-check first that the O-Ring of
both connectors are properly fitted
and dust caps do not get squashed!
Disassembly: Reassembly:
4x
6x
Install 6 screws 2.5x8 (751478) ,
torque to 40Ncm.
Install down holder ring .
Connect long coaxial connector on the lower side
of the LNA board (ME LNA) .
Install LNA board .
Remove LNA board .
Install 12 screws M2.5x8 (751478) ,
torque to 40Ncm.
4x
99804907
99810981
99810982
99848988
99848990
99848996
99791678 (OEM615B)
99833981 (OEM617B)
99844735 (OEM719B)
794577
99791680
796474 (OEM615B 99806084
833725 (OEM617B, OEM719B) 99846513
99855730
756111 (4x)
The procedures described in this chapter have to be General tools for disassembly/reassembly:
used for replacing of internal modules of the following
antenna: Install of self tapping screws: Make
sure to first turn the screws counter-
clockwise, until the screws lock into the
520716 Torque screwdriver “10 … 120Ncm”
520717 Torque screwdriver “100 … 600Ncm”
"11.1 GS15" on page 2 existing threads, to avoid possible 712234 Torx insert “T8/50”
wear out of the thread. 779262 Torx insert “T10/50”
740255 Torque screwdriver bit with ball head
746045 Socket spanner #5.5 reworked
520893 Adapter 6kt to 4kt (1/4”)
Caution:
ESD (Electro Static Discharge). Make
sure your workbench has the neces-
sary precautions against ESD.
Depending of the version of the fitted shielding body, different screws are used.
18x
Disconnect HF cable .
Install UHF U-Ring .
Connect HF cable .
Disconnect internal antenna cable Align internal antenna cable
in direction . at cable guides .
Remove UHF U-Ring . Connect internal antenna cable in reverse
direction of to the LNA board.
4x
Pull flex cable carefully out of the ferrite . Pull flex cable carefully through ferrite .
Double-check that the antenna
cable is laid in the notch as shown
in picture !
Remove 6 screws .
Install 6 screws M3x14 (395252) .
Remove Measurement Engine (ME) ,
ME holder and Processorboard . Install Processorboard , ME holder and
Measurement Engine (ME) .
Disassembly:
Install 8 screws 2.5x6 (744642) ,
torque to 40Ncm.
Install antenna element carefully.
Align the two arrows of the antenna element
Remove 8 screws . in direction of notch .
Remove antenna element .
8x
8x
Remove 8 screws . Install 8 screws 2.5x8 (736851) ,
Remove downholder ring . torque to 40Ncm.
Remove LNA board . Align the two arrows of the LNA board and
the “peak” of the downholder ring in direction
of notch .
Disassembly:
Remove 3x screws .
Remove flex clamp with foam .
3x
On GS15 with old shielding body are
M2.5x5 screws 757346 used!
3x
Remove 4x damping rings with special washer . Install 4 damping rings (768908) with
special washer (768859) .
4x
2x
Release nuts of the Lemo connectors and . Torque nuts and to 300Ncm.
Remove Lemo nut with washer and dust cap .
Remove Lemo nut with washer and dust cap .
Double-check that the dust caps do not
get squashed!
Disassembly & Reassembly GS15 11-14 SML GS10-GS14-GS15-GS16 - 08/2020
Disassembly: Reassembly:
Lift the electronics consisting of filter board (with Slide the electronics consisting of filter board (with
flex cables), Slot-In/HF-Switch flex and flex cables), Slot-In/HF-Switch flex and
Lemo flex cables carefully out of the Lemo flex cables carefully into the
lower housing. lower housing.
2x
Release nut of external antenna connector . Torque nut of external antenna connector
Remove external antenna connector to 300Ncm.
with washer and dust cap . Install external antenna connector
with washer and dust cap .
To install the Bluetooth cable , pull the cable
To remove the Bluetooth cable , disconnect the through the ferrite and connect it.
cable and pull it through the ferrite. Connect flex cable , orientation:
Disconnect flex cable .
To remove the HF cable for the UHF antenna ,
pull the cable through the ferrite.
Remove 4 screws .
Remove cable covering plate .
Remove 2 screws . Install 2 screws 2.5x6 (744642) ,
Remove SD card flex . torque to 40Ncm.
Position pad of the SD card flex
over the hole.
Install SD card flex .
2x
Measurement Engine
Housing and MMI
LNA Board
Radio Module
99979270 Processorboard GS 99842317 ME4 Rev. 4 (ref. BDU) 768535 3LED Flex
(ref. board index D) for Viva SmartWorx firmware ≥ v5.70
for Viva SmartWorx firmware ≥ v10.00, 99815666 ME4 Rev. 3 (ref. BDU)
upwards compatible to all newer Viva for Viva SmartWorx firmware ≥ v5.05
SmartWorx firmware versions 99766700 ME4 Rev. 2.1 (or lower) (ref. BDU)
99878956 Processorboard GS for all Viva SmartWorx firmware versions
for Viva SmartWorx firmware ≥ v6.00,
upwards compatible to all newer Viva
SmartWorx firmware versions
769338 MMI Flex cable 12 Pin
161185 M3 nut
for board stack
804803 Housing GS14 UHF & GSM cpl. 847017 Housing Basic / GS16 UHF & GSM cpl. 99804907 Processor board tested GS14
incl. Lemo connector incl. Lemo connector 2G (BGS2-W)
793467 SIM/SD card cover GS14 842568 SIM/SD card cover GS16 while stock lasts
847208 Battery cover gasket 847208 Battery cover gasket 99810981 Processor board tested GS14
3.75G (PHS8P)
99810982 Processor board tested GS14
3.75G USA/CAN (PXS8)
797873 Housing GS14 GSM only cpl. 847018 Housing GS16 Basic / GSM only cpl.
incl. Lemo connector incl. Lemo connector
793467 SIM/SD card cover GS14 842568 SIM/SD card cover GS16
847208 Battery cover gasket 847208 Battery cover gasket
NO Hole
NO Hole
836617 LNA board 796474 EMC contact spring GS14 (OEM615B) 804651 GSM Antenna cpl.
732843 Dust cap Lemo GS14 / GS16 773958 Dust cap QN connector
812553 GS14 Type Label - 3.75G 925482 GS14 Type Label - 3.75G+UHF (JP)
771136 Swiss Technology label
952370 GS16 Type Label - no GSM+UHF 925476 GS16 Type Label - 3.75G+UHF900 848528 GS16 Type Label - 3.75G+UHF (JP)
SATEL TR4+ SATEL TR9 SATEL M3-TR4
99979270 Processorboard GS 99842317 ME4 Rev. 4 (ref. BDU) 764886 Filter board GS15 assembled
(ref. SNo board index D) for Viva SmartWorx firmware ≥ v5.70
for Viva SmartWorx firmware ≥ v10.00, 99815666 ME4 Rev. 3 (ref. BDU)
upwards compatible to all newer Viva for Viva SmartWorx firmware ≥ v5.05
SmartWorx firmware versions 99766700 ME4 Rev. 2.1 (or lower) (ref. BDU)
99878956 Processorboard GS for all Viva SmartWorx firmware versions
for Viva SmartWorx firmware ≥ v6.00,
upwards compatible to all newer Viva
SmartWorx firmware versions
739037 Washer for LEMO connector red 774006 Washer for QN connector
767203 Housing gasket GS15 When changing from the old style
shielding body to the new style body,
order also the respective screws!
219805 M3 nut
for board stack
99848337 SLR6, Satelline M3-TR4, 403-473 MHz 99848339 SLR6-1, Satelline M3-TR4, 403-473 MHz
(assembled with Slot-In Cover cpl.) (without Slot-In Cover)
99770701 AS10, triple frequency GNSS antenna 892427 AS11, multi frequency GNSS antenna
876925 Protection rubber AS05-10 (green) 887767 Protection rubber AS11 (black)
Rev 4.0
776552 STC-03
918251 Power Supply 30V / 6A needed for GS10
749448 Antenna Signal Tester 639964 GAT1, Radio Antenna (400 - 435MHz)
667243 GAT2, Radio Antenna (435 - 470MHz)
Order 2 pieces!
740535 Lemo bit for torque screwdriver 866478 Cable Extraction tool 520893 Adapter 6kt to 4kt (1/4")
6x
Load Signal
Connector
Test Indicator
PWR
Standard Connector Slot-In
4/6V
+12V
-12V
12V
Load 12V 4/6V
_ Test
current consumption
“0” “1”
DTR Switch
PWR Switch 3x
+ PWR1 PWR2
P1 P2 P3 P4 P5
The universal multi-purpose STB-01 Testbox provides following features: The STB-01 Testbox is equipped with following test ports to interface the
different instruments:
PWR switch to shift the power supply between PWR1and PWR2 on The three standard ports P1, P2 and P3 provide the mainly needed function-
instruments with a PWR port (e.g. GS10). alities such as USB 2.0 “High speed” (over an internal USB hub), RS232,
Current measuring port . GPIO test interface, etc. inclusive a 12V load test.
Indicators for the 12V and 4/6V load tests . When the green LED shines the The PWR port is especially designed for testing the PWR port of the
load test passed. Viva GNSS sensors (e.g. GS10) and provides among others the switchable
Signal indicators , not needed yet. The two LEDs can indicate signals up to PWR1/PWR2 power output.
12V and down to -12V. When the orange LED shines the test passed. Slot-In port , not needed yet.
DTR switch to shift the DTR signal of the RS232 interface manually between Each port has an 12V load test (Slot-In port: 4/6V and 12V) which can be
HIGH and LOW. released by pressing the corresponding button .
_
+ USB
RS232
V_var in
Caution:
ESD (Electro Static Discharge). Make sure your workbench has the
necessary precautions against ESD.
This chapter covers the following GNSS receiver upgrade kits: 14.1.1 Upgrade Kit content
99841798 - GUS106 Upgrade Kit GS10 OEM7xx
99841799 - GUS107 Upgrade Kit GS14 OEM7xx
99841800 - GUS108 Upgrade Kit GS15 OEM7xx
99841798 - GUS106 Upgrade Kit GS10 OEM7xx
The upgrade process for all instruments is the same.
1x 99963759 OEM729R (ref.836618 - BMGZ)
For “unlimited” instruments please see next chapter.
1x 866741 Housing GS10 complete (OEM7)
1x 732863 Housing sealing
5.
Adjustment
Replace the screws and the washers at every
disassembly of the instrument.
Connect unit to SERIS and go to “Adjust” .
Clear System (“Delete Licenses”)
Licenses Key: “Auto KeyGen”
Code: “Set OEM AuthCode keys automatically”
6. Load firmware Load the currently installed instrument firmware again
to bring the OEM7 to the assigned firmware.
7. Unlock satellite Unlock the satellite systems via Webserver, refer to
systems "OEM AuthCode" chapter 7 on page 12.
8. Tracking Test Perform tracking tests as necessary to check the
function of the new OEM7.
9. Outgoing Test Perform an Outgoing Test and Final Read-out.