Professional Documents
Culture Documents
COMPTEX FV
COMPTEX EASY-FV
CUD-FV
C2E-FV C2I-FV
FRONT MAIN PANEL
PAGE 1 – LANGUAGE PAGE
2 4 7 5
2) Indicator of motorized teflon sheet position setting. This unit is active only on
machine provided of this disposal.
5) Buttons Group
Heating – cooling function button. This button has a double function. When main
cylinders are cool ( below 80 ° C ) it start to move and heat the cylinders in order to
prevent thermal shock to the felts: This function is useful during job starting. When
main cylinders are hot ( more than 80 °C ) it start to move the cylinders and close
heating valves. Machine automatically stop when temperature reach 80 °C.
Introduction photocells setting. When this function is enable, machine stops if there
is not fabric on introduction.
Cooling device on setting. Push once to swich on, push again to swich off.
Reverse speed button. This button is active only after pressing and releasing
emergency button. Use only for safety reason because reverse speed can damage
teflon sheets.
Introduction load cell. When this function is enabled, you can work with manual
potentiometer.
Manual preheating steamer. Open steam flow on manual control. Normally use after
long time stop of the machine in order to heat steam chambers.
Password.
Push this button to go to LOAD CELL SETTING page. (Active only on machine
provided of this disposal)
1
3
5 4 6
1) Temperature control unit of first cylinder. This unit let the operator set the requested
temperature of the first cylinder. SET temperature is the requested temperature. In order to
change it touch the set value and type the new value ( than touch OK button ). value is the
measured temperature.
2) Temperature control unit of second cylinder. This function is useful only if the machine is
provided of double thermoregulation.
3) Temperature control unit of polishing cylinders. This function is active only after pressing the
button number 4. This unit is active only on machine provided of this disposal.
If this feature is not enabled, you can work with the polishing cylinder at room
temperature. This function is active only for machine provided of polishing
calander option.
6) Electric power.
This feature allows you to view the electrical absorption of motor and inverter.
1
3
1) Motorized teflon sheet position setting. This unit is active only on machine provided of this
disposal. In order to change teflon sheet position press on number area and adjust the position
by increasing or decreasing arrows. On not provided machine position of teflon sheets can be
regolated by manual watches on front and back side.
2) Steam flow control unit . This unit is active only on machine provided of this disposal. Operator
can set value of the steam flow out of the steam chamber as a percentage of overall flow. It is
possible to adjust by pressing arrows or to set the requested value by touching.
3) Compacting percentage.
This page counter contains all counter parameters such as meters, yard and number of fold. Then
there are also indications of productions hours.
Turning on additional lamp. This function works only on machine provided with this
device.
This unit has not machine functions but is useful for writing message or remind some important
detail. Sometimes is used for operators free written sentences.
It can be used as a normal blackboard. it is possible to write freely with a finger or a soft plastic
tools.
DO NOT USE METAL OR HARD MATERIAL NOT TO DAMAGE THE PANEL.
1) OPEN A RECIPE.
Touch recipe name on screen and press this button to open it. On left side all
parameter get set according to the new recipe. This is not active into the
machine till DOWNLOAD button is pressed.
2) SAVE A RECIPE.
With this button is possible to save a recipe in panel memory. Check the
name of the recipe before saving and at least create a new name by RECIPE
NAME Button.
3) RECIPE NAME.
Touch the number of receip and press this button. Then
type the name of the recipe and press OK. Set the
parameters and save the recipe with SAVE button.
This button load all data from the PLC and display them on blue screen.
5) DOWNLOAD.
6) This button load all recipe data into the PLC and get the machine active
with the new recipe.
2) Push this button to reset the allarm (not valid for all type of allarm).
2
1
5
3
Platform UP.
Platform DOWN.
Rolling up setting button. This button is used when the machine must be set to
work in rolling up position. Press this button before lifting the platform. Folding
rolls move to a back position then it is possible to lift the platform. This function
is active only on machine provided of this disposal.
This page is a temperature displayed page. Temperature values are settable only from the main
panel
Refers to PAGE 11 for details of functions.
This page counter contains all counter parameters such as meters , yard and number of fold. Then
there are also indications of productions hours.
This page is for typing all production parameter that are printed on label (on machine provided whit
printer system).
In order to modify the parameters just press on value string and type target parameter.
Fabric meters are automatically loaded from partial meter at discharging sequens, roll weight is
automatically loaded from weight system and roll number increase value each sequens.