Professional Documents
Culture Documents
Faculty of Engineering
Department of Mechanical Engineering
Ph. D. Entrance Test
3. Mobile No:---------------------------------------------------------------------------
4. Highest Qualification:--------------------------------------------------------------
5. Area of Specialization:-------------------------------------------------------------
Instruction
----------------------------------------------------------------------------------------------------------------
Q-36 The neutral axis of the cross-section a beam is that axis at which the bending stress
is
a) Zero b) Minimum c) Maximum d) Infinity
Q-37 Which of the following material has maximum ductility?
a) Mild steel b) Copper c) Nickel d) Aluminium
Q-38 An eutectoid steel consists of
a) Wholly pearlite b) Wholly austenite
c) Pearlite and ferrite d) Pearlite and cementite
Q-39 Shock resisting steels should have
a) Low wear resistance b) Low hardness
c) Low tensile strength d) Toughness
Q-40 The mechanical efficiency of an impulse turbine is
a) Ratio of the actual power produced by the turbine to the energy actually supplied
by the turbine
b) Ratio of the actual work available at the turbine to the energy imparted to the
wheel
c) Ratio of the Work done on the wheel to the energy of the jet
d) None of the above
Q-41 In a Kaplan turbine runner, the number of blades are generally between
a) 2 to 4 b) 4 to 8 c) 8 to l6 d) 16 to 24
Q-42 The automobile radiator is a heat exchanger of
a) Parallel flow type b) Counter flow type
c) Cross flow type d) Regenerator type
Q-43 A heat pump working on a reversed Carnot cycle has a C.O.P. of 5. It works as a
refrigerator taking 1 kW of work input. The refrigerating effect will be
a) 1 kW b) 2 kW c) 3 kW d) 4 kW
Q-44 Which of the following statement is correct?
a) The constant enthalpy lines are also constant wet bulb temperature lines.
b) The wet bulb and dry bulb temperature are equal at saturation condition.
c) The wet bulb temperature is a measure of enthalpy of moist air.
d) All of the above
Q-45 In electrolux refrigerator
a) Ammonia is absorbed in hydrogen
b) Ammonia is absorbed in water
c) Ammonia evaporates in hydrogen
d) Hydrogen evaporates in ammonia
Q-46 Which of the following parameters influence the axial feed rate in centreless
grinding?
a) Regulating wheel diameter
b) Speed of the regulating wheel
c) Angle between the axes of grinding and regulating wheels
d) All of the above
Q-47 The lathe spindles are usually made hollow and provided with
a) Internal taper b) External taper
c) Internal and external taper d) No taper
Q-48 In a single point tool, the angle between the surface of the flank immediately below
the point and a line drawn from the point perpendicular to the base, is known as
a) Side relief angle b) End relief angle
c) Back rake angle d) Side rake angle
Q-49 EDM machining is applied for
a) Shaping carbide dies and punches having complicated profiles
b) Making large number of small holes in sieves and fuel nozzles
c) Embossing and engraving on harder materials
d) All of these
Q-50 Dielectric is used in
a) Electro-chemical machining b) Ultra-sonic machining
c) Electro-discharge machining d) Laser machining
Medi-Caps University
Faculty of Engineering
Department of Mechanical Engineering
Ph. D. Entrance Test
1 b 26 d
2 c 27 b
3 b 28 a
4 c 29 d
5 c 30 c
6 b 31 b
7 a 32 b
8 b 33 a
9 d 34 a
10 c 35 d
11 d 36 a
12 b 37 a
13 b 38 a
14 a 39 d
15 a 40 b
16 b 41 b
17 c 42 c
18 b 43 d
19 c 44 d
20 a 45 c
21 a 46 d
22 c 47 a
23 a 48 b
24 c 49 d
25 d 50 c