Professional Documents
Culture Documents
Aquaflex
Flexible waterproofing slurry
DESCRIPTION mortar. Care must be taken when choosing the repair
mortar to ensure that it has all necessary approvals
Aquaflex is a ready to use flexible slurry based on a for contact with potable water. If the surface contains
special synthetic resin dispersion and a blend of small blow holes, typically less than 1mm wide, the
selected cements mixed with carefully graded coating can be applied directly onto the substrate
aggregate. without the need for a treatment. Cracks which are
less than 0.3mm in width can be over coated as long
USES
as the crack is not likely to open up to greater than
Aquaflex is used for: 0.3mm (this is greater than the maximum permissible
crack widths recommended in bs 8007:1987, the
Protection and repair of balconies, terraces and British Standard Code of Practice for the design of
hunching concrete of roads and bridges. concrete structures for retaining aqueous liquids).
Waterproofing of new and old buildings (internal
and external) Cracks that are greater than 0.3mm in width should be
Waterproofing of tanks, containers and water chased-out to 4mm in width and approximately 15mm
reservoirs. in depth. This should be filled with Aquaflex (applied
Waterproofing of top roof, basement, water tank, using less liquid providing a thicker consistency).
bath room, swimming pool & dams etc. When the material in the crack has hardened the
coating should be applied over the crack.
BENEFITS
PHYSICAL PROPERTIES
Excellent waterproof barrier.
Effective on negative or positive side. Normal Coverage 2 Kg/m2/2 Coats
High bond strength.
@ 10ºC – 2 hrs
Excellent freeze/thaw resistance. @ 20ºC –1 hour
Pot Life
Excellent resistance to chloride ion @ 30ºC – 0.5 hour
penetration.
Brush, trowel, or spray applied. Recoatable 16 hours.
Resistant to mechanical
Reliable application. Hardening Time
stress : 3 days
Self-curing. Full cure : 7 days
Low in lace cost. Attained after 7 days cure
Non-toxic. Resistance to Water
Possitive pressure : 20
Good abrasion resistance. Atmospheres
pressure
Negative pressure : 4
Approved for use in potable water systems.
atmospheres
BONDING / PRIMING
MIXING
No priming required.
It is essential to use a mechanical mixer, such as a
SURFACE PREPARATION slow speed electric drill fitted with a suitable paddle.
Our Technical Department will be pleased to supply
All surfaces that are to receive the coating must be details of blade design.
free from oil, grease, wax, dirt or any other form of
foreign matter that might affect adhesion. Typically Fill approximately three quarters of component A (milky
concrete may require grit blasting. liquid) into a pail and, with continuous stirring, slowly
add component B (grayish powder). Mixing must be
Spelled]= surfaces or those containing large
continued until the mix is homogeneous and free of
blowholes and other such defects should be repaired
lumps.
using Aquaflex or Chem Coats approved repair
Trowel: horizontal surfaces – the first layer of Aquaflex This product has a shelf life of 12 months if kept in a
should be applied to a thickness of 1 – 1.5mm using a dry cool place in the original packaging. In more
normal trowel. Allow to cure for approximately 16 hours extreme conditions this period might be shortened.
and then apply a second layer using a notched trowel. HEALTH & SAFETY
This is immediately levelled with a spiked roller.
Aquaflex powder is irritating to eyes, respiratory
On vertical surfaces, the first layer should be applied system and skin. Avoid inhalation of dust and wear
with a notched trowel and the second on with a flat suitable respiratory protective equipment.
trowel. Aquaflex should not be applied thicker than Aquaflex liquid is not classified as dangerous.
1.5mm per coat. Aquaflex when mixed becomes highly alkaline. Water
suitable protective clothing, gloves and eye protection.
Spray: contact our Technical Department for details
For both components and mixed material avoid contact
of the special equipment required. GLOVES with skin and eyes. In case of contact with eyes or skin
IMPORTANT NOTE
RANGE OF PRODUCTS
WATERPROOFING SYSTEMS PREPACKED REPAIR MORTARS SEALANTS
INDUSTRIAL FLOOR SURFACES CEMENTITIOUS & EPOXY GROUTS CRACK INJECTION
PROTECTIVE COATINGS CONCRETE ADMIXTURES CONCRETE ADHESIVE