Professional Documents
Culture Documents
ISO 8734:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
© ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet central@iso.ch
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii
INTERNATIONAL STANDARD ©
ISO 8734:1997(E) © ISO
Table 1 — Dimensions
Dimensions in millimetres
d m61) 1 1,5 2 2,5 3 4 5 6 8 10 12 16 20
c ª 0,2 0,3 0,35 0,4 0,5 0,63 0,8 1,2 1,6 2 2,5 3 3,5
l 2)
nom. min. max.
3 2,75 3,25
4 3,75 4,25
5 4,75 5,25
6 5,75 6,25
8 7,75 8,25
10 9,75 10,25
12 11,5 12,5
14 13,5 14,5
16 15,5 16,5
2
© ISO ISO 8734:1997(E)
See table 2.
Martensitic
Steel
stainless steel
C1 in accordance
St
with ISO 3506-1
Type A Type B
either or
hardened and
Material
1)
C 0,95 to 1,1 C 0,06 to 0,13 C 0,15 max. tempered to a
Si 0,15 to 0,35 Si 0,1 to 0,4 Si 0,10 max. hardness of
Mn 0,25 to 0,4 Mn 0,25 to 0,6 Mn 0,9 to 1,3 460 HV30 to
P 0,03 max. P 0,025 max. P 0,07 max. 560 HV30
S 0,025 max. S 0,05 max. S 0,15 to 0,35
Cr iTeh STANDARD PREVIEW
1,35 to 1,65 Pb 0,15 to 0,35
(standards.iteh.ai)
at the supplier's discretion
3
ISO 8734:1997(E) © ISO
5 Designation
EXAMPLE 1
A through hardened steel parallel pin type A, with nominal diameter d = 6 mm and nominal length l = 30 mm is
designated as follows:
EXAMPLE 2
A martensitic stainless steel parallel pin of grade C1, with nominal diameter d = 6 mm and nominal length
l = 30 mm is designated as follows:
4
iTeh STANDARD PREVIEW
(standards.iteh.ai)
ISO 8734:1997
https://standards.iteh.ai/catalog/standards/sist/63b23e14-2faf-4202-b387-
3db6074db25a/iso-8734-1997
ISO 8734:1997(E) © ISO
ICS 21.060.50
Descriptors: fasteners, steel products, pins (mechanics), straight pins, specifications, characteristics, dimensions, designation.