Professional Documents
Culture Documents
7UDNWRUNPHWLMVNLLQJR]GDUVNLVWURML9DUQRVWQL]DWLþLQY]PHWQL]DWLþ0HUHLQ
]DKWHYH
Tractors and machinery for agriculture and forestry -- Linch pins and spring pins --
Dimensions and requirements
ICS:
65.060.01 Kmetijski stroji in oprema na Agricultural machines and
splošno equipment in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST ISO 7072:1995
INTERNATIONAL Is0
STANDARD 7072
Second edition
1993-09-15
Reference number
IS0 7072:1993(E)
SIST ISO 7072:1995
IS0 7072:1993(E)
Foreword
0 IS0 1993
All rights reserved. No part of this publication may be reproduced or utilized in any form or
by any means, electronic or mechanical, including photocopying and microfilm, without per-
mission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
SIST ISO 7072:1995
This International Standard specifies the dimensions The material of linch pins shall have a tensile strength
and certain requirements for linch pins and spring
SIST ISO 7072:1995
of at least 500 N/mm*, and be so chosen that a linch
https://standards.iteh.ai/catalog/standards/sist/950709cf-0a4d-40af-a43e-
pins, which are used for the three-point hitch and for pin can be bent 30” against a 5 mm radius without
numerous fastening purposes in farm work 773a509e8bae/sist-iso-7072-1995
and agri- showing any cracks (see figure2).
cultural equipment.
The pre-stress, F, of the spring-retaining device
shown in figure 1 shall be 20 N to 30 N. The spring-
2 Normative reference retaining device shall withstand being opened
10 000 times without a noticeable reduction in pre-
The following standard contains provisions which, stress.
through reference in this text, constitute provisions
of this International Standard. At the time of publi- As regards finish of linch pins, any anti-corrosive
cation, the edition indicated was valid. All standards treatment shall be by agreement with the manufac-
are subject to revision, and parties to agreements turer.
based on this International Standard are encouraged
to investigate the possibility of applying the most re- 4 Spring pins
cent edition of the standard indicated below. Mem-
bers of IEC and IS0 maintain registers of currently
valid International Standards. 4.1 Dimensions
IS0 683-l 4: 1992, Heat-treatable steels, alloy steels Dimensions of spring pins shall be in accordance with
and free-cutting steels - Part 14: Hot-rolled steels figure 3 and table 2.
for quenched and tempered springs.
4.2 Requirements
3 Linch pins The material of spring pins shall be spring steel of
type ... as specified in IS0 683-l 4:1992.
3.1 Dimensions
As regards finish of spring pins, any anti-corrosive
Dimensions of linch pins shall be in accordance with treatment shall be by agreement with the manufac-
figure 1 and table 1. turer.
SIST ISO 7072:1995
IS0 7072:1993(E)
Dimensions in millimetres
Spring-retaining
c device I)
I
: I
I I
7 I
I /I
’ I’
:
: :
I
:
: :
:
F-
.-:. I1
M3
I @h
1
IS”
n
iTeh STANDARD
r *-- PREVIEW 7
(standards.iteh.ai)
SIST ISO 7072:1995
https://standards.iteh.ai/catalog/standards/sist/950709cf-0a4d-40af-a43e-
773a509e8bae/sist-iso-7072-1995
I) Configuration of the ring is optional, but shall ensure that it does not rotate.
bl b2 b3 h C
I
4 a I
min. max. max. min. max. max.
8 7,5 Tit; 8 7 9 15 9 32 22 42 12
10 9,5 ';I; 10 8 10 15 12 32 22 45 14
12 II It 0,5 12 9 11 15 14
I' 34
I 22
IL 45
I 18
45 55
1
I 17 16 + 0,5
I
17
I
12,5
I
14 21 20
I
45 29 60 21
2
SIST ISO 7072:1995
IS0 7072:1993(E)
Dimensions in millimetres
Dimensions in millimetres
4 1) 4 12
Nominal size 4 4 +3
min. max. 0 approx.
2 x 40 2 9 9 12 41 23
3 x 70 3 13 12 18 67 40
4x75 4 19 15 22 75 50
5x105 5 26 18 24 105 65
6x115 6 31 24 35 117 70
8x150 8 35 40 55 150 88
1) Recommended dimensions