Professional Documents
Culture Documents
II5258-1
28NOV07
Supersedes II5258-1
13NOV07
Restricted
INSTALLATION INSTRUCTIONS
for the
Kodak DirectView CLASSIC/ELITE CR SYSTEMS
Service Code: 5258, 5259
Important
• Qualified service personnel must install this equipment.
• When performing the procedures outlined in this document, personnel must always
employ safe work practices and wear the appropriate personal protective equipment
(e.g., safety eyewear) in accordance with Company Standard Operating Procedures.
H219_0001GC
This equipment includes parts and assemblies sensitive to damage from electrostatic
discharge. Use caution to prevent damage during all service procedures.
Table of Contents
Description Page
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Necessary Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Equipment on a WALL STAND . . . . . . . . . . . . . . . . . . . . . . . 19
Installing the Equipment on a FLOOR STAND . . . . . . . . . . . . . . . . . . . . . . 26
Installing the Equipment on Customer-Supplied Equipment . . . . . . . . . . 36
Connecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Energizing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Doing the Configuration for the LOCAL USER INTERFACE (LUI) . . . . . . 39
Doing the Configuration for the Software . . . . . . . . . . . . . . . . . . . . . . . . . . 43
INSTALLATION INSTRUCTIONS Safety
28NOV07
II5258-1
Page
Section 1: Safety
3 of 44
This information defines the safety and information icons used in this publication.
Radiation
This icon is used for conditions that could cause personal injury from radiation.
Laser Warning
This icon is used for conditions when a laser beam could cause injury to a person.
Caution
This icon is used for conditions that could cause injury to a person, or damage to the
equipment or software data.
ESD
Possible damage from electrostatic discharge.
This icon is used for conditions that could cause damage to the equipment.
Electrostatic discharge (ESD) is a primary source of:
• equipment failure
• equipment repairs
A person cannot detect an electrical charge of less than 3,500 V, but 30 V can cause
damage to components in the equipment.
INSTALLATION INSTRUCTIONS Safety
28NOV07
II5258-1 Preventive Measures
Page
4 of 44 • Check for an ESD WARNING LABEL before doing any procedure with ESD-sensitive
components. All sensitive components have graphic LABELS that frequently include
instructions. Use all label instructions.
• Wear a GROUNDING STRAP when you touch ESD-sensitive components. Check that the
CLIP remains fastened to a ground that has a clean surface with no paint.
• Repair components in an ESD-protection area or use a PORTABLE GROUNDING MAT.
• When moving ESD-sensitive components from area to area, insert and transport the
components in the special material made for the transport of these components.
Important
This icon is used for important information.
Note
This icon is used for additional information.
INSTALLATION INSTRUCTIONS Packing List
28NOV07
II5258-1
Page
Section 2: Packing List
5 of 44
FRONT
COVER
H219_3000GCA
H219_3000GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
2 SCREWS CONNECTOR 2 Loosen the 2 SCREWS to allow access
Page
8 of 44
COVER to the 2 CONNECTORS.
3 Rotate the CONNECTOR COVER.
4 Disconnect the 2 CONNECTORS.
H219_3001ACA
2 CONNECTORS H219_3001AC
5 Remove:
4 SCREWS
TOP COVER
• 4 SCREWS
• TOP COVER
H219_3002GCA
H219_3002GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
LEFT PANEL
6 Loosen the 4 SCREWS.
Page
9 of 44 7 Remove the LEFT PANEL.
4 SCREWS
8 Loosen the 4 SCREWS.
9 Remove the RIGHT PANEL.
4 SCREWS
H219_3003GCA
H219_3003GC RIGHT PANEL
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 5 SCREWS 9 SCREWS
Page
10 of 44
BACK EMI
PANEL
5 SCREWS
H219_3004HCA
RIGHT EMI PANEL
H219_3004HC
10 Remove:
• 5 SCREWS
• RIGHT EMI PANEL
• 5 SCREWS
• LEFT EMI PANEL
• 9 SCREWS
• BACK EMI PANEL - rotate and lift
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 11 Check the SHOCK WATCH on the side
Page
11 of 44 SHOCK WATCH of the frame.
12 Is the SHOCK WATCH red?
Yes No
Stop the installation Continue with
procedure and call the Step 13.
TSC.
H219_3026ACA
H219_3026AC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
12 of 44
2 SCREWS
2 SCREWS 2 SCREWS
REAR SHIPPING REAR SHIPPING
BRACKET BRACKET
FRONT
FRONT SHIPPING
SHIPPING
H219_3005HCA 4 SCREWS BRACKET
H219_3005HC BRACKET 2 SCREWS
2 SCREWS
2 SCREWS
H219_3006BCA
H219_3006BC
Important
You must keep the SHIPPING BRACKET in the CLASSIC/ELITE CR SYSTEM, or a light leak
could occur.
15 Remove and keep the 2 SCREWS on the side of the SHIPPING BRACKET.
16 Loosen the 2 SCREWS on the end of the SHIPPING BRACKET.
17 Slide the SHIPPING BRACKET toward the outside of the system.
18 Tighten the 2 SCREWS on the end of the SHIPPING BRACKET.
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
14 of 44
SWITCH
CB1
4 VOLTAGE
JUMPERS
WIRE TIE
JUMPER
Important
You must determine the correct JUMPER to connect to the VOLTAGE CONNECTOR. The
correct JUMPER might not be the same JUMPER removed in the graphic.
LATCH
H219_3007GCA
ERASE LAMP AY H219_3007GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 27 Remove and discard the REMOVE AT
Page
16 of 44 INSTALL TAB.
S VE
LL
IN O
T EM
TA
R
A
REMOVE AT
INSTALL TAB
H219_3027GCA
H219_3027GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 28 Install:
Page
17 of 44 • BACK EMI PANEL
• 9 SCREWS
• LEFT EMI PANEL
• 5 SCREWS
• RIGHT EMI PANEL
• 5 SCREWS
• LEFT PANEL
• RIGHT PANEL
29 Tighten the 2 SCREWS for:
• LEFT PANEL
• RIGHT PANEL
30 Install:
• TOP COVER
• 4 SCREWS
31 Connect the 2 CONNECTORS.
32 Rotate the CONNECTOR COVER.
33 Tighten the 2 SCREWS.
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 34 Install the 10 ERASE LAMPS into the
Page
18 of 44
ERASE LAMP AY ERASE LAMP AY.
35 Push the ERASE LAMP AY into the
system.
36 Install the FRONT COVER.
10 ERASE LAMPS
H219_3008GCA
H219_3008GC
Important
The SUPPORT RAIL must be installed:
2 SUPPORT BRACKETS
• by the customer
• before you start to assemble the
SUPPORT RAIL
remaining components of the WALL
STAND
• to match local codes
2 SET • to support a total weight of 45.5 kg
SCREWS (100.0 lbs)
H219_3035GCA
H219_3035GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 5 Rotate to install the COMPUTER
Page
20 of 44 COMPUTER BRACKET BRACKET at the top of the SUPPORT
RAIL.
6 Tighten the 2 SCREWS.
7 Install:
• FRONT COMPUTER BRACKET
COMPUTER
BRACKET
• 2 THUMB SCREWS - leave loose
2 SCREWS
FRONT
COMPUTER
BRACKET
SUPPORT
RAIL
2 THUMB
H219_3036GCA SCREWS
H219_3036GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 8 Install:
Page
21 of 44 • MONITOR ARM
• WASHER
• SCREW
MONITOR ARM • KEYBOARD ARM
• WASHER
• SCREW
WASHER
SCREW
KEYBOARD ARM
WASHER
H219_3037GCA
H219_3037GC SCREW
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 9 Install:
Page 4 SCREWS
22 of 44 • MONITOR
• 4 SCREWS
10 Are you installing a KEYBOARD TRAY?
Yes No
Continue with Advance to
Step 11. Step 12.
MONITOR
H219_3040ACA
H219_3040AC
11 Install:
KEYBOARD
TRAY • KEYBOARD TRAY
• 4 SCREWS
• BAR CODE READER HOLDER
• 4 SCREWS
• BOOT
BAR CODE
READER
• SCREW
HOLDER
4 SCREWS
H219_3038ACA
SCREW H219_3038AC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 12 Install directly to the KEYBOARD ARM:
Page
23 of 44 BAR CODE • BAR CODE READER HOLDER
READER
KEYBOARD
HOLDER
ARM • SCREW
SCREW
H219_3039ACA
H219_3039AC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
24 of 44
FRONT COMPUTER
BRACKET
2 THUMB SCREWS
COMPUTER
MONITOR ARM
MONITOR
SUPPORT RAIL
KEYBOARD
2 SUPPORT BRACKETS
KEYBOARD ARM
KEYBOARD TRAY
HOSPITAL
NETWORK
BAR CODE
READER
MOUSE
POWER
MONITOR
VOLTAGE SWITCH
POWER
SUPPLY
H219_3041HC
FLOOR STAND
H219_3017GCA
H219_3017GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 3 Install the 3 LEVELING FEET into the
Page
27 of 44 bottom of the BASE.
3 LEVELING FEET
BASE
H219_3018ACA
H219_3018AC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
28 of 44
STAND
8 SCREWS
8 TABS
H219_3019HCA BASE
H219_3019HC
2 SCREWS
LOCATOR H219_3020ACA
H219_3020GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page MONITOR MONITOR
30 of 44
SHELF SHELF
KEYBOARD
SHELF SCAN GUN
BOOT
4 NUTS SCREW
SCAN GUN BOOT
3 NUTS
FLOOR STAND
SCREW
2 BIN LINERS
H219_3021HCA
H219_3021HC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
31 of 44
Important
• Some sites may not install:
– KEYBOARD SHELF
– SCAN GUN BOOT
• If you are not installing the optional KEYBOARD SHELF, the SCAN GUN BOOT can be
installed to the MONITOR SHELF. See the above graphic.
9 Install:
• MONITOR SHELF
• 3 NUTS
• KEYBOARD SHELF - optional
• 4 NUTS
• SCAN GUN BOOT - optional
• SCREW
• 2 BIN LINERS
10 Level the FLOOR STAND.
11 Move the LOCATOR fully down to the floor.
12 Tighten the 2 SCREWS.
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
FLOOR STAND
13 Place the FLOOR STAND in the correct
Page
32 of 44 position at the site.
LOCATOR 14 Move the CLASSIC/ELITE CR SYSTEM
onto the FLOOR STAND.
15 Align the 2 WHEELS into the 2
NOTCHES in the LOCATOR.
2 NOTCHES
H219_3022ACA
H219_3022AC 2 WHEELS
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
MONITOR
16 Place the COMPUTER in front of the
Page
33 of 44 FLOOR STAND.
KEYBOARD 17 Install the equipment on the FLOOR
STAND:
• MONITOR
• KEYBOARD - optional
• MOUSE - optional
MOUSE
• BAR CODE READER - optional
BAR CODE
READER
FLOOR STAND
H219_3016GCA COMPUTER
H219_3016GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 18 See the graphic to route the wires.
Page
34 of 44
H219_3024GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page COMPUTER KEYBOARD
35 of 44
HOSPITAL
NETWORK
BAR CODE
READER
MOUSE
POWER
MONITOR
VOLTAGE SWITCH
POWER
SUPPLY
H219_3041HC
COMPUTER KEYBOARD
HOSPITAL
NETWORK
BAR CODE
READER
MOUSE
POWER
MONITOR
VOLTAGE SWITCH
POWER
SUPPLY
H219_3041HC
Caution
Dangerous Voltage
2 LOCKING
NUTS
FRONT
PANEL
2 HOLD
DOWN FEET
H219_3011GCA floor
H219_3011GC
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1 Energizing the System
Page
39 of 44
Laser Warning
• This equipment uses a visible red LASER. Prevent direct exposure to the beam from the
LASER when the system is energized.
• Dangerous Voltage
1 Energize:
• COMPUTER
• system
• MONITOR
4 Touch:
• [Network Configuration].
• [Ethernet Settings]
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
41 of 44
green ARROW
5 Select the correct “Link Speed and Duplex Value” for the site.
6 Touch:
• green ARROW
• [TCP/IP Settings]
INSTALLATION INSTRUCTIONS Installation
28NOV07
II5258-1
Page
42 of 44
VALUE BOX
Important
You must do the necessary procedures for a new system.