Professional Documents
Culture Documents
II5258-1
21JUL09
Supersedes II5258-1
01JUN09
Restricted
Installation Instructions
for the
KODAK DIRECTVIEW Classic/Elite CR Systems
Service Code: 5258, 5259
Important
• Qualified service personnel must install this equipment.
• See the Service Portal for possible updates before using this document.
• When doing the procedures in this document, you must use safe work practices and wear
the correct personal protective equipment (for example, safety eyewear) according to your
company’s standard operating procedures.
H219_0001GC
This equipment includes parts and assemblies sensitive to damage from electrostatic
discharge. Use caution to prevent damage during all service procedures.
Table of Contents
Description Page
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Necessary Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Preparing for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Wall Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Floor Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Unpacking the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the Equipment on a Wall Stand . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installing the Equipment on a Floor Stand . . . . . . . . . . . . . . . . . . . . . . . . . 32
Installing the Equipment on Customer-Supplied Equipment . . . . . . . . . . 36
Connecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Energizing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Doing the Configuration for the Local User Interface (LUI). . . . . . . . . . . . 40
Doing the Configuration for the Software . . . . . . . . . . . . . . . . . . . . . . . . . . 44
INSTALLATION INSTRUCTIONS Safety
21JUL09
II5258-1
Page
Section 1: Safety
3 of 45
This information defines the safety and information icons used in this publication.
Radiation
This icon is used for conditions that could cause personal injury from radiation.
Laser Warning
This icon is used for conditions when a laser beam could cause injury to a person.
Caution
This icon is used for conditions that could cause injury to a person, or damage to the
equipment or software data.
ESD
Possible damage from electrostatic discharge.
This icon is used for conditions that could cause damage to the equipment.
Electrostatic discharge (ESD) is a primary source of:
• equipment failure
• equipment repairs
A person cannot detect an electrical charge of less than 3,500 V, but 30 V can cause
damage to components in the equipment.
INSTALLATION INSTRUCTIONS Safety
21JUL09
II5258-1 Preventive Measures
Page
4 of 45 • Check for an ESD warning label before doing any procedure with ESD-sensitive
components. All sensitive components have graphic labels that frequently include
instructions. Use all label instructions.
• Wear a grounding strap when you touch ESD-sensitive components. Check that the CLIP
remains fastened to a ground that has a clean surface with no paint.
• Repair components in an ESD-protection area or use a portable grounding mat.
• When moving ESD-sensitive components from area to area, insert and transport the
components in the special material made for the transport of these components.
Important
This icon is used for important information.
Note
This icon is used for additional information.
INSTALLATION INSTRUCTIONS Packing List
21JUL09
II5258-1
Page
Section 2: Packing List
5 of 45
Important
The SUPPORT RAIL must be installed:
2 SUPPORT BRACKETS
• by the customer
• before you start to assemble the
SUPPORT RAIL
remaining components of the WALL
STAND
• to match local codes
2 SET • to support a total weight of 45.5 kg
SCREWS (100.0 lbs)
H219_3035GCA
H219_3035GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 5 Rotate to install the COMPUTER
Page
9 of 45 COMPUTER BRACKET BRACKET at the top of the SUPPORT
RAIL.
6 Tighten the 2 SCREWS.
7 Install:
• FRONT COMPUTER BRACKET
COMPUTER
BRACKET
• 2 THUMB SCREWS - leave loose
2 SCREWS
FRONT
COMPUTER
BRACKET
SUPPORT
RAIL
2 THUMB
H219_3036GCA SCREWS
H219_3036GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 8 Install:
Page
10 of 45 • MONITOR ARM
• WASHER
• SCREW
MONITOR ARM • KEYBOARD ARM
• WASHER
• SCREW
9 Are you installing a KEYBOARD TRAY?
Yes No
Continue with Advance to
WASHER
Step 10. Step 11.
SCREW
KEYBOARD ARM
WASHER
H219_3037GCA
H219_3037GC SCREW
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 10 Install:
Page KEYBOARD
11 of 45 TRAY • KEYBOARD TRAY
• 4 SCREWS
• BAR CODE READER HOLDER
• 4 SCREWS
• BOOT
BAR CODE
READER
• SCREW
HOLDER
4 SCREWS
H219_3038ACA
SCREW H219_3038AC
SCREW
H219_3039ACA
H219_3039AC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 Installing the Floor Stand
Page
12 of 45 1 Unpack:
KEYBOARD SHELF • FLOOR STAND
• KEYBOARD SHELF - optional
• SCAN GUN BOOT - optional
2 Check the packing lists.
FLOOR STAND
H219_3017GCA
H219_3017GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
13 of 45
STAND
8 SCREWS
8 TABS
H219_3019HCA BASE
H219_3019HC
2 SCREWS
LOCATOR H219_3020ACA
H219_3020GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page MONITOR MONITOR
15 of 45
SHELF SHELF
KEYBOARD
SHELF SCAN GUN
BOOT
4 NUTS SCREW
SCAN GUN BOOT
3 NUTS
FLOOR STAND
SCREW
2 BIN LINERS
H219_3021HCA
H219_3021HC
Important
• Some sites may not install:
– KEYBOARD SHELF
– SCAN GUN BOOT
• When you are not installing the optional KEYBOARD SHELF, the SCAN GUN BOOT can
be installed to the MONITOR SHELF, as shown in the above graphic.
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 8 Install:
Page
16 of 45 • MONITOR SHELF
• 3 NUTS
• KEYBOARD SHELF - optional
• 4 NUTS
• SCAN GUN BOOT - optional
• SCREW
• 2 BIN LINERS
9 Place the FLOOR STAND in the correct position at the site.
10 Level the FLOOR STAND.
11 Move the LOCATOR fully down to the floor.
12 Tighten the 2 SCREWS.
13 Continue with Unpacking the Equipment.
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 Unpacking the Equipment
Page
17 of 45 1 Pull and lift to remove the FRONT
COVER.
FRONT COVER
H219_4033ACA
H219_4033AC
2 SCREWS CONNECTOR
2 Loosen the 2 SCREWS to allow access
COVER to the 2 CONNECTORS.
3 Rotate the CONNECTOR COVER.
4 Disconnect the 2 CONNECTORS.
H219_3001ACA
2 CONNECTORS H219_3001AC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 5 Remove:
Page
4 SCREWS
18 of 45 TOP COVER • 4 SCREWS
• TOP COVER
H219_5032GCA
H219_5032GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 6 Remove:
Page LEFT COVER
19 of 45 • 4 SCREWS
4 SCREWS
• LEFT COVER
• 4 SCREWS
• RIGHT COVER
4 SCREWS
H219_5031GCA
H219_5031GC RIGHT COVER
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page 5 SCREWS 9 SCREWS
20 of 45
BACK EMI
PANEL
H219_3061HCA
H219_3061HC
7 Remove:
• 5 SCREWS
• LEFT EMI PANEL
• 9 SCREWS
• BACK EMI PANEL - rotate and lift
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 8 Check the TILT WATCH on the back of
Page
21 of 45 the frame.
9 Is the TILT WATCH red?
Yes No
Stop the installation Continue with
procedure and call the Step 10.
Technical Support
Center
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
22 of 45
2 SCREWS
2 SCREWS 2 SCREWS
REAR SHIPPING REAR SHIPPING
BRACKET BRACKET
FRONT
FRONT SHIPPING
SHIPPING
H219_3062HCA 4 SCREWS BRACKET
H219_3062HC BRACKET 2 SCREWS
tighten
2 SCREWS
SLOW SCAN
TOWER
H219_3071BCA
H219_3071BC SHIPPING BRACKET
12 Remove and discard the 2 SCREWS from the SLOW SCAN TOWER portion of the
SHIPPING BRACKET.
13 Loosen the 2 SCREWS on the POWER SUPPLY portion of the SHIPPING BRACKET.
14 Pull the SHIPPING BRACKET away from the SLOW SCAN TOWER and towards the
outside of the system.
15 Tighten the 2 SCREWS on the POWER SUPPLY portion of the SHIPPING BRACKET.
Note
You must keep the 2 SCREWS in the POWER SUPPLY portion of the SHIPPING BRACKET,
or a light leak could occur. The PLATE SUPPORT ASSEMLY could hit the SHIPPING
BRACKET if you position the SHIPPING BRACKET incorrectly.
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
24 of 45
SWITCH
CB1
4 VOLTAGE
JUMPERS
WIRE TIE
JUMPER
Important
You must determine the correct JUMPER to connect to the VOLTAGE CONNECTOR. The
correct JUMPER might not be the same JUMPER removed in the graphic.
Important
Do not remove the ERASE LAMP
ASSEMBLY.
2 SCREWS
BRACKET
H219_3063GCA
ERASE LAMP AY H219_3063GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 26 Remove and discard the REMOVE AT
Page
26 of 45 INSTALL TAB.
A E
T M
IN O
R
S VE
TA
LL
REMOVE AT
H219_3064GCA INSTALL TAB
H219_3064GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 27 Install:
Page
27 of 45 • BACK EMI PANEL
• 9 SCREWS
• LEFT EMI PANEL
• 5 SCREWS
• LEFT COVER
• 4 SCREWS
• RIGHT COVER
• 4 SCREWS
28 Install:
• TOP COVER
• 4 SCREWS
29 Connect the 2 CONNECTORS.
30 Rotate the CONNECTOR COVER.
31 Tighten the 2 SCREWS.
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 32 Install the 10 ERASE LAMPS into the
Page ERASE LAMP AY
28 of 45 ERASE LAMP ASSEMBLY.
33 Push the ERASE LAMP ASSEMBLY
into the system.
34 Install the FRONT COVER.
10 ERASE LAMPS
H219_3065GCA
H219_3065GC
MONITOR
H219_3040ACA
H219_3040AC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
30 of 45
FRONT COMPUTER
BRACKET
2 THUMB SCREWS
COMPUTER
MONITOR ARM
MONITOR
SUPPORT RAIL
KEYBOARD
2 SUPPORT BRACKETS
KEYBOARD ARM
KEYBOARD TRAY
VOLTAGE
unused
SWITCH POWER
POWER PS/2 PORTS
KEYBOARD COM3/unused
MOUSE (ignore the
COM1/unused
painted PC label
that says COM2)
MONITOR
TOUCHSCREEN
BAR CODE
READER USB
KEYBOARD
USB MOUSE
MONITOR COM 4
unused
COM 3 BAR CODE
extra NIC
READER
COM 1
TOUCHSCREEN CUSTOMER
CUSTOMER NETWORK
H219_0011GCA NETWORK H226_1027GCA
H219_0011GC H226_1027GC
Important
• You will first connect the COMPUTER to the Classic/Elite CR System.
• After you do the software installation procedures, you will then connect both to the
hospital network at the site:
– COMPUTER
– Classic/Elite CR System
2 NOTCHES
H219_3022ACA
H219_3022AC 2 WHEELS
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
MONITOR
4 Place the COMPUTER in front of the
Page
33 of 45 FLOOR STAND.
KEYBOARD 5 Install the equipment on the FLOOR
STAND:
• MONITOR
• KEYBOARD - optional
• MOUSE - optional
MOUSE
• BAR CODE READER - optional
BAR CODE
READER
FLOOR STAND
H219_3016GCA COMPUTER
H219_3016GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 6 See the graphic to route the wires.
Page
34 of 45
H219_3024GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 Figure 3 Model 8810 Computer Figure 4 Model HP5700 Computer
Page
35 of 45
VOLTAGE
unused
SWITCH POWER
POWER PS/2 PORTS
KEYBOARD COM3/unused
MOUSE (ignore the
COM1/unused
painted PC label
that says COM2)
MONITOR
TOUCHSCREEN
BAR CODE
READER USB
KEYBOARD
USB MOUSE
MONITOR COM 4
unused
COM 3 BAR CODE
extra NIC
READER
COM 1
TOUCHSCREEN CUSTOMER
CUSTOMER NETWORK
H219_0011GCA NETWORK H226_1027GCA
H219_0011GC H226_1027GC
Important
• You will first connect the COMPUTER to the Classic/Elite CR System.
• After you do the software installation procedures, you will then connect both to the
hospital network at the site:
– COMPUTER
– Classic/Elite CR System
VOLTAGE
unused
SWITCH POWER
POWER PS/2 PORTS
KEYBOARD COM3/unused
MOUSE (ignore the
COM1/unused
painted PC label
that says COM2)
MONITOR
TOUCHSCREEN
BAR CODE
READER USB
KEYBOARD
USB MOUSE
MONITOR COM 4
unused
COM 3 BAR CODE
extra NIC
READER
COM 1
TOUCHSCREEN CUSTOMER
CUSTOMER NETWORK
H219_0011GCA NETWORK H226_1027GCA
H219_0011GC H226_1027GC
Important
• You will first connect the COMPUTER to the Classic/Elite CR System.
• After you do the software installation procedures, you will then connect both to the
hospital network at the site:
– COMPUTER
– Classic/Elite CR System
Caution
Dangerous Voltage
2 LOCKING
NUTS
FRONT
PANEL
2 HOLD
DOWN FEET
H219_3066GCA floor
H219_3066GC
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 Energizing the System
Page
40 of 45
Laser Warning
• This equipment uses a visible red LASER. Prevent direct exposure to the beam from the
LASER when the system is energized.
• Dangerous Voltage
1 Energize:
• COMPUTER
• system
• MONITOR
4 Touch:
• [Network Configuration].
• [Ethernet Settings]
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
42 of 45
green ARROW
5 Select the correct “Link Speed and Duplex Value” for the site.
6 Touch:
• green arrow
• [TCP/IP Settings]
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1
Page
43 of 45
VALUE BOX
Important
• You must do the necessary procedures for a new system.
• You must see the Service Knowledge Portal for the latest software instructions.
1 Do the modification instructions and software installation instructions for Software Version
5.x for the KODAK DIRECTVIEW CR 825/850/950/975 Systems and the KODAK
DIRECTVIEW Classic/Elite CR Systems.
2 Disconnect the COMPUTER from the Classic/Elite CR System.
3 Connect to the network at the site:
• COMPUTER
• Classic/Elite CR System
INSTALLATION INSTRUCTIONS Installation
21JUL09
II5258-1 Publication History
Page
45 of 45
Publication Publication Changed
ECO No. File Name Notes
Date No. Pages
13NOV07 II5258-1 - - - --- ii5258_1.fm New Publication
28NOV07 II5258-1 - - - 1 ii5258_1.fm Revision
07APR08 II5258-1 - - - All ii5258_1.fm Revision
01JUN09 II5258-1 - - - All ii5258_1.fm Revision
21JUL09 II5258-1 - - - 1 ii5258_1.fm Revision