Professional Documents
Culture Documents
This document highlights new product features and enhancements in Edgecam 2014 R1.
To run Edgecam and Part Modeler 2014 R1, the expiry date in the license must be September 2013 or later.
www.edgecam.com
Contents
‘WHAT’S NEW’ DOCUMENT OVERVIEW .................................................................................................................. 6
IMPORTANT INFORMATION .................................................................................................................................... 7
SOFTWARE UPDATE 1 .............................................................................................................................................. 8
SOFTWARE UPDATE 2 .............................................................................................................................................. 8
Manufacture Enhancements
NEW USE CURRENT STOCK OPTION ............................................................................................................................. 9
NEW CHAMFERING CYCLE ......................................................................................................................................... 9
SUPPORT FOR 3D NORMAL OFFSET OUTPUT............................................................................................................... 10
DYNAMIC OFFSET .................................................................................................................................................. 10
HIGH FEED LINK OPTION ON GROOVING CYCLES .......................................................................................................... 11
New Finish Grooving .................................................................................................................................. 11
Rough Grooving ......................................................................................................................................... 11
ROUGHING CYCLE - CLEARANCE ................................................................................................................................ 11
NEW OPTION TO DISPLAY PARAMETRIC SHANK GRAPHICS ............................................................................................. 12
PLUGINS AVAILABLE IN GENERATE CNC CODE ............................................................................................................. 12
CRC CANCEL ON RAPID LIFT OUT ............................................................................................................................. 12
NEW COOLANT CONTROLS IN TURNING ..................................................................................................................... 13
WIRE - ONAARICUT TECHNOLOGY ............................................................................................................................ 13
Workflow Enhancements
MACHINE FEATURE OPTION ..................................................................................................................................... 14
STOCK MANAGER FILTERS ....................................................................................................................................... 14
MACHINE MANAGER POST PROCESSORS .................................................................................................................... 14
COMPONENT SETUP - MOVE.................................................................................................................................... 15
FIXTURE DATABASE - AUTOMATIC FIXTURE PLACEMENT ................................................................................................ 15
FIXTURE MANAGER - FILTERING................................................................................................................................ 15
FIXTURE MANAGER - HIDE MODIFIERS....................................................................................................................... 16
MACHINE SETUP - MATING LOCATION ....................................................................................................................... 16
FIXTURE DATABASE - CHUCKS................................................................................................................................... 17
CHUCK FIXTURE SETUP............................................................................................................................................ 18
AUTO ALIGNMENT OF C-AXIS FEATURE ...................................................................................................................... 18
STRATEGY IMPROVEMENTS ...................................................................................................................................... 19
Strategy tool selection for Milling and Turning now considers Roughing and Finishing tool status ......... 19
Improved Turn / Bore tool selection ......................................................................................................... 19
Improvements to Grooving ....................................................................................................................... 19
Interface Enhancements
LAUNCHER AND WELCOME SCREEN IMPROVEMENTS .................................................................................................... 20
RENDERING PERFORMANCE INCREASE........................................................................................................................ 20
Performance .............................................................................................................................................. 20
Intellisnap .................................................................................................................................................. 20
MASK EDITOR USER INTERFACE ................................................................................................................................ 21
NEW CPL MARKER ................................................................................................................................................ 21
IMAGES AND TOOL TIPS .......................................................................................................................................... 22
EDITABLE RIBBON BAR ............................................................................................................................................ 23
VERIFY ENTITIES - ANGLE INFORMATION ON FACES....................................................................................................... 23
CYCLES - RESET ALL PICKS........................................................................................................................................ 24
NC EDITOR - RIBBON BAR ....................................................................................................................................... 24
Licensing
REVOCATION OF NETWORK LICENSES OVER THE INTERNET .............................................................................................. 37
NEW 'SHOP FLOOR SOLIDS' MODULE LICENSE FOR SHOP FLOOR EDITOR ........................................................................... 37
UPGRADE TO SENTINEL RMS VERSION 8.5.3 .............................................................................................................. 37
SAVING PARTS WHEN CONNECTION TO A NETWORK LICENSE SERVER IS LOST....................................................................... 37
SINGLE CLS WORKS WITH THE R1 AND R2 RELEASES..................................................................................................... 38
MAINTENANCE DATABASE REPORT....................................................................................................................... 39
NEW FEATURES IN VERSION 2013 R2 .................................................................................................................... 40
Important Information
New Graphics Sub System
We have upgraded the Edgecam graphic system for this release. It now matches Code Wizard and Simulator which
were upgraded in the last release.
Graphic Drivers
With the update to the graphic sub system, we strongly recommend that you check that the latest WHQL certified
driver has been installed.
Windows XP Support
Edgecam 2014 R1 will install and run on Windows XP. However, as this operating system nears its 'End of Support'
milestone in April 2014 (ref: http://windows.microsoft.com/en-GB/windows/products/lifecycle), we cannot
guarantee to resolve any issues that are found to be specific to Windows XP.
Windows 8 Support
The following versions of Windows 8 are supported for Edgecam 2014 R1:
Windows 8 Professional.
Windows 8 Enterprise.
Note: Windows 8 RT is not supported.
Edgecam shipments
There are 2 main Edgecam releases each year; the R1 release in October and the R2 release in April.
The R1 releases are shipped on DVD and available to download from the Customer Portal for customers
who have a valid maintenance contract.
The R2 releases are only available to download from the Customer Portal for customers who have a valid
maintenance contract.
Software Update 1
For a full list of maintenance items resolved in Edgecam 2014 R1 SU1, please refer to the Edgecam 2014 R1 SU1
Maintenance Database Report.
Software Update 2
For a full list of maintenance items resolved in Edgecam 2014 R1 SU2, please refer to the Edgecam 2014 R1 SU2
Maintenance Database Report.
Manufacture Enhancements
New Use Current Stock option
In the previous version, the Mill Hole Cycle did not consider the Stock Model when determining the Level and
Clearance.
A Use Current Stock option has been added to the Clearance Associated To modifier on the General tab of the Mill
Hole Cycle. When selected, the Clearance and Level will be associated with the current Stock and Fixtures.
The Use Current Stock option is only available under the following conditions:
Model Type set to Solid (only valid for Hole Features).
Mill environment only.
Planar Mode active.
When selected, the following modifiers will be adjusted:
The Clearance value will be added to the highest point on the stock or the fixtures selected in the last
Update Fixtures command. This is a single value for all holes selected. If the stock/Fixture is not found or
is below the top of the Model, the Model high point will be used.
The Retract value will be an increment to the Level value.
The Level value will be added to the top of the stock above the hole. This will be determined by dropping
a tool (slightly bigger end mill) onto the stock. Potentially, each hole could have its own level. If no stock is
found or it is below the level of the feature, the Hole Feature level will be used.
The Depth will be recalculated to include the Level adjustment if required. The Depth value will then be
added.
Dynamic Offset
A new Dynamic option has been added to the Datum Type
field of the Machining Sequence dialog Datum Shift dialog,
Index Operation dialog, Merging Sequences dialog and
Index dialog - General tab.
When the part is rotated, the datum rotates with the part.
The co-ordinates will be relative to this new datum
position. The active CPL will still be in the same place as it
is for Absolute. The image depicts XYZ zero point for NC
output.
Rough Grooving
A new High Feed rate Link Move option has been added to
the Link Type settings on the Advanced tab.
When High Feed is selected, the link moves are done at the
Maximum Feedrate, as specified on the 'Machine
Parameters Dialog - Turret tab' of the machine in Code
Wizard.
Workflow Enhancements
Machine Feature option
A new Machine Feature option has been added to the
Machining Tab that allows the machining strategies to be
applied without the need to use the Planning Board by
simply clicking the feature.
Jaw reverse
Strategy Improvements
Strategy tool selection for Milling and Turning now considers Roughing and Finishing tool
status
Roughing and Finishing strategies for milling and turning now consider the status of the Roughing and Finishing
checkboxes for tool selection.
1. First look for a dedicated roughing tool that matches the search criteria.
2. If a tool is not found, it will search again for a tool which is capable of both Roughing and Finishing.
3. If not found, it will search again for a tool with no roughing or finishing specified.
If the tool is set as a Finishing only tool it will not be selected for Roughing.
Similarly, for Finishing, the strategy will first search for a dedicated finishing tool which matches the search criteria,
before searching for a dual purpose tool capable of both. Finishing strategies will not select a dedicated Roughing
tool.
All searches are performed in the Toolkit before searching the wider ToolStore.
Additionally, if the tool search fails to find a left-handed tool, it will search again for a right-handed reversed tool.
Improvements to Grooving
The Rough Groove cycle can leave cusps of uncut material and, therefore, a Finishing cycle is now applied to
remove these cusps prior to final finishing.
Interface Enhancements
Launcher and Welcome Screen Improvements
Launcher
The Edgecam Launcher has several enhancements
including:
Right-clicking an entry in the Recently Used Files
list allows you to delete the entry and copy the
file name or the full path to clipboard.
Ability to scroll in the Recently Used Files list by
clicking and holding the mouse scroll wheel.
Resizing when using a low-resolution monitor.
Note: Edgecam Minimum Requirement is still 17"
Colour monitor (1280 x 1024 screen resolution).
Ability to pin URL and Folders to the Tools menu.
Code Generator removed from the tools section.
Live Job Reports added to the Tools section.
Welcome Screen
The Welcome dialogs adapt, depending on the screen
resolution, to fit all of the information. The Wire option
on Workflow has also been removed.
Intellisnap
When the model was rotated or panned, the Intellisnap was still active and affected the speed. We automatically
turn off Intellisnap when a mouse key is held down which improves performance.
Key benefits:
Faster report generation.
Uses latest technology.
Runs as a web browser and, therefore, it is
available on PCs, smartphones and tablets.
Information is always up to date (Refresh no
longer required.
New Materials report.
New Tools report
PDF, Excel, Word and Image printing formats.
Flexible and powerful search and filter engines for
jobs, tools and materials.
Limitations:
Guide curves can only be constructed with the 3D
Wireframe tools (3D lines, 3D Cubic Splines and 3D
Nurbs).
Limitations:
Guide curves can only be constructed with the 3D
Wireframe tools (3D lines, 3D Cubic Splines and 3D
Nurbs).
Limited to using 3 Guide Curves.
The profile will be swept to the length of the Drive
Plane or the shortest Guide Curve.
Limitations:
Variable radii will not be found.
Freeform curved faces will not be found.
Milling Macros
A Dynamic setting has been added to the STYPE System Variable in the following Milling macro:
Milling Macro Reference (MACRO 43 - INDEX PALLET).
XPARTNORMAL, YPARTNORMAL and ZPARTNORMAL System Variables have been added to the following Milling
macro:
Milling Macro Reference (MACRO 2 - MOVE FEED).
SUBFUNCT and FIELD 12 System Variables have been added to the following Milling macro:
Milling Macro Reference (MACRO 1 - MOVE RAPID).
Sync Points
A Sync Point will now identify whether or not a Sync has been generated from an Update Stock using a new
SYNCFROMUPDATESTOCK system variable. The value of this variable will be 1 when coming from an Update Stock
and 0 when coming from any other 4-axis sync. You can then use this to create logic on the post to skip Sync Points
from Update Stock, if required.
Note: Update Stock is a true synchronisation point; Edgecam and Simulator may behave differently from the
machine if you decide to skip these points.
Templates
The following Template changes have been implemented:
1. We have added a new Code Constructor and NC Style/ Hole Cycles option with a drop-down list named
Back Bore / Face Cycle Points where the default is Use Common:
Don't Use will call the cycle definition Code Constructor for each point.
Use Common will call the normal cycle points for each point (current behaviour).
Use Dedicated will call the new Back Bore / Face Cycle Points.
2. The [WORKREGISTER] token has its value fixed for the TNC template. [WORKGCODE2] has been created for
other templates and is available at Set Work Datums. [WORKGCODE2] will contain the override while
[WORKGCODE] will not have the override. The user should use the appropriate one, according to the
machine/process requirements.
3. Milling templates have received a new parameter to configure the precision of rotary movements. The
Minimum angular movement parameter is on the NC File General tab of NC-Style area. Rotary output will,
from now on, use that value for rounding purposes. This should eliminate problems where angular
precision was incompatible with linear precision.
4. We have implemented support for smooth code output on the TNC through an Exact Stop Code
Constructor. There is not a point on the setvar for single shot or modal since M90 works only in the line in
which it is programmed. If users want it for a different purpose, they still have the Code Constructor to set
it On/Off. The token is included on Linear, Circular and Helical code constructors.
5. Rotary Axis tokens are now present on the Set Work Datums Code Constructor.
Licensing
Revocation of network licenses over the Internet
Edgecam 2014 R1 introduces the ability to revoke network licenses in one simple operation using the CLS License
Manager. Please note the following requirements:
Requirements:
Sentinel RMS License Manager Version 8.5.1 or higher is installed on the server PC (version 8.5.3 is
available on your product DVD).
CLS 2014 or above is installed on the Server PC (Edgecam does not need to be installed).
The Server PC has an Internet connection.
The features of this new method are:
It will revoke all of the licenses for the selected servercode automatically.
If licenses for multiple Vero products are installed on the server under different servercodes, only the
licenses for the selected servercode will be revoked.
Licenses cannot be revoked if any of them are in use and a warning is issued about this.
This method can only be used via CLS License Manager on the Server PC. For details on how to use the new
procedure, please refer to network_RevokeLicense.pdf which is on the DVD and installed with CLS.
New 'Shop Floor Solids' module license for Shop Floor Editor
A new 'Shop Floor Solids' module license has been introduced to provide the ability to load Edgecam part files
containing CATIA V5 and Creo Parametric solids bodies into Shop Floor Editor. Please contact your local reseller for
further details.
This change means that when Edgecam 2014 R2 is released, we will update CLS 2014 so there is only one 2014 CLS
installation that will work with both the R1 and R2 releases.
Workflow
Workflow aims to make Edgecam easier to use by providing a
framework to guide the user from a new CAD model to NC code
as intuitively as possible. It uses guided automation to help the
user accomplish the tasks of part setup, analysis and feature
creation, manufacture and deployment. The new ribbon toolbar
layout is designed to work from left to right and guide the user
through the manufacturing process in sequential steps.
At each stage, Workflow will attempt to make automatic
decisions or suggestions as to how best to achieve the goal:
each automatic decision can easily be changed by the user. For
example, the initial decision as to machine on a Lathe or Mill will
be made automatically by analysing the geometry of the
component but can be changed or refined using the interface
immediately, before progressing to the next step.
Interactive Picking
The Mill cycle dialogs have been updated to include buttons for
selecting data interactively.
The top of the dialog now has a series of pictures indicating
what data is required:
As the data is picked, the appropriate button is
ticked.
Some picking is only required when a particular
option has been selected, for example, Start
Points or Stock Profile. The button will be greyed
out until that option is enabled.
If any buttons are left without data after the OK
button has been clicked, a prompt will be
displayed.
Initial Sequence
In previous releases, users were presented with a full dialog
covering all of the options for Mill, Turn and Wire.
The Initial Sequence now only displays the options required for
each discipline.
Decimal Separator
Edgecam and ToolStore have been improved to support the use
of comma as a decimal separator.
If the Operating System is set to use comma as a decimal
separator, Edgecam and ToolStore will now interpret the
comma as a decimal separator. In Edgecam, a dot (point) can
still be used because it will be recognised and converted to the
system decimal separator as soon as the dialog is closed.
Note: A comma cannot be used when the Operating System is
set to use dot (point) as a decimal separator because Edgecam
was conceptually created to use dot (point) as the only decimal
separator.
Limitations:
Only supported in Edgecam and ToolStore.
Edgecam will allow the use of both comma and
dot (point) when the Operating System is set to
use comma as a decimal separator. However,
ToolStore will only allow the use of comma.
The Advanced 5 Axis cycle does not currently
support the use of comma.
Code Wizard does not support the use of comma
as a decimal separator; for example, on machine
parameters.
When comma is the decimal separator, a 'space'
is interpreted as a partial confirmation of co-
ordinate inputs.
Docking Dialogs
A new Enable Docking For Cycle Dialogs option has been added
to the Title bar of each dialog. This new option enables the
Dialog windows for cycles to be docked at the left or right side
of the viewing area and, optionally, hidden to keep the viewing
area uncluttered.
Mill Enhancements
Protect Solid
A new Protect Solid parameter has been added to the Control
tab.
When machining Face features, the cycle is not aware of the
whole solid and will machine only the given feature resulting in
the tool going into the part. Protect Solid makes the cycle aware
of the solid model and prevents gouges when trimming out the
toolpath.
This should avoid the need for boundary creation in several
parts and improve confidence when applying toolpath.
Turn Enhancements
Compensation of None
Selecting a Compensation option of None no longer offsets for
tool nose radius.
Previously, the Compensation options were only available when
the Canned Cycle option was checked. These options are now
always available.
Wire Enhancements
Open Profile
Open Profile options have been added to the Approach/Retract
Tab specifying the Start and End extensions to be added to the
wire toolpath when machining open profiles. The extensions are
tangential and are only applied to open profiles.
User Technology
In the previous release, only Machine Technology was available
when selecting Material and Wire which could not be amended.
Edgecam 2013 R2 introduces the possibility for users to create
their own User Technology and recall this when required.
Machine and User Technologies are stored in separate
databases; the User Technology database is written to the
Machdef folder of the user.
The Material and Wire lists now contain Machine Technology
and User Technology which is highlighted in Blue.
Moving Faces
We have introduced a Move Face procedure to help the user
modify a third party model and prepare it for manufacture. This
new function will allow the user to:
Move the position of "dumb" features, for
example, pockets and bosses, around the model.
They can either be moved from the original CAD
datum position or relative to a user defined
position using Translation and Rotation.
Modify areas of features, for example, pocket
walls and boss heights, on a third party model.
Individual faces can be moved using Translation
and Rotation in X, Y or Z or a combination of
these.
These enhancements will greatly improve preparation for
manufacture when working with third party models.
Analyzing Profiles
The Analyze Profile procedure within Part Modeler has been
improved to help users interrogate the constraints on sketches
and also show areas of potential problems prior to modelling.
The improved function:
Displays a summary of the sketch profile in one dialog
box.
Allows the user to click the Show button to display the
areas of concern on the sketch, such as overlapping
entities and open profiles.
Displays the number of under constrained entities within
the sketch. Also, when the user moves the mouse cursor
over the sketch entity, it will list the missing constraints.
3D Mirror
The 3D Mirror procedure within Part Modeler has been
improved and now allows two previously unavailable options,
Copy and Move, to be used. The following procedures are now
available:
Copy
Copies the entities and keeps the original
entities.
Note: All associated features such as thread data
and surface finish will be copied. However, if the
original entities are edited, the copied (mirrored)
entities will not be updated.
Reference
Copies the entities and keeps the original
entities.
Note: If the original entities are edited, the
copied (mirrored) entities will be updated.
However, any associated features such as thread
data and surface finish will not be transferred.
Move
Moves the entities about a defined mirror plane.
Offset Faces
It is now possible to use a window selection to select multiple
faces when using the Offset Face procedure within Part
Modeler. This new function will:
Allow multiple faces of a feature to be selected
easily to allow offsetting of the "dumb" feature.
Allow faces that are fully within a window
selection to be selected (Left to Right window
selection).
Allow faces that are partially within the window
selection to be selected (Right to Left window
selection).
Simulator Enhancements
Program Stop
Simulator has been enhanced in version 2013 R2 and now
recognises a Program Stop Stop Option.
Sampled Stock
Simulator has been enhanced in version 2013 R2 and now
provides the option to use Sampled instead of Triangular Stock
which will improve speed at the expense of accuracy.
The new functionality should be used for large, complex parts
which Rapid Result could not previously process since it does
not support multi-axis.
Note:
This functionality is not intended for prismatic
parts.
This option allows Rapid Result for multi-axis
parts and is not meant to be used for Simulation.
Therefore, a Using Sampled Stock. Rendering
once every hundred cuts message is displayed in
Simulation when this option is checked.
Applicable to Milling only.
32 or 64-bit Simulator
The Use 64-bit Simulator option in Edgecam Preferences has
been removed for Edgecam 2013 R2.
Simulator now automatically starts up in the appropriate mode,
i.e. 32 or 64-bit, depending on the Operating System being used.
Toolstore Enhancements
Coolant Options
A Coolant option has been added to the Tool Mounting
Parameters allowing you to specify whether the tool can pass
coolant and the method used (Off, Flood, Mist or Air).
The Through Coolant option in the Tool Geometry Parameters
has been enhanced to provide a High Pressure selection.
Note: The new options will be available on both Milling and
Turning tools. However, the Mist and Air Coolant options will
have no effect on Turning.
DWG/DXF Improvements
The following improvements have been made:
Files from Autodesk LT are now imported.
Support for Autocad 2013 format.
Paper Space support.
CAD Systems
Edgecam 2013 R2 can load data from the following CAD systems
(subject to the appropriate license):
Part Modeler - up to and including 2013 R2 (with
CAD link support).
Autodesk Inventor - 2013 and 2014- there is CAD
link support for the 32-bit and 64-bit versions.
SolidWorks - 2012 and 2013 - there is CAD link
support for the 32-bit and 64-bit versions.
Solid Edge ST4 and ST5 - there is CAD link support
for the 32-bit and 64-bit versions. Edgecam and
CAD links support synchronous and ordered part
files and assemblies.
™
Creo Parametric 2.0 - (previous names Creo
Elements/Pro, Pro/ENGINEER, Wildfire).
CATIA V5 - (solids only) up to and including R22.
UGS NX – up to and including NX8.
SpaceClaim 2012 and 2012+ (with CAD link
support for 2012+ (32-bit and 64-bit versions)).
KOMPAS-3D (KOMPAS-3D software must be
installed on your computer).
VISI CAD version 20.
SolidLink 64-bit
SolidLink, the application that loads all CAD models into
Edgecam and Part Modeler, has been improved:
SolidLink is now available as a 64-bit in addition
to the 32-bit version. The 64-bit version can
handle larger files.
The Edgecam and Part Modeler installers will
automatically select the correct version for the
Operating System.
Protection of Graphics
To ensure that manufacturer's graphics are protected, the CGD
file can be locked.
When a CGD file is locked, it is not possible to copy any of the
graphics; the Copy function is greyed out.
In addition, in Edgecam, if a .tmc file is generated from a locked
CGD file, the machine graphics will not be copied.
Template Changes
There have been a number of changes to Code Wizard
templates in Edgecam 2013 R2.
Below is a summary of changes:
Moriseiki Template
A multiple turret capability has been added to
the Moriseiki template.
Further improvements have been made with
respect to individual tool change positions and, in
particular, for moves to tool change as
coordinate positions.
Adaptive ISO and Adaptive Siemens Milling
Templates
A CGX capability has been added to the Adaptive
ISO and Adaptive Siemens milling templates.
New Tokens
Mill
NEXT_COMMENT Next Comment
NEXT_DESCRIPTION Next Description
NEXT_GROUP Next Group
NEXT_GROUP_NUMBER Next Group Number
NEXT_GROUP_TEXT Next Group Text
NEXT_ID Next ID
NEXT_ID_NUMBER Next ID Number
NEXT_ID_TEXT Next ID Text
SPEED-DWELL Calculates and outputs dwell time for speed
change
Turn
NEXTDESCR Next Tool Description
NEXTCOMMENT Next Tool Comment
NEXT_GROUP Next Group
NEXT_GROUP_NUMBER Next Group Number
NEXT_GROUP_TEXT Next Group Text
NEXT_ID Next ID
NEXT_ID_NUMBER Next ID Number
NEXT_ID_TEXT Next ID Text
Coolant Options
The Coolant option in the Milling Cutter Spindle Parameters has
been enhanced allowing you to specify whether the tool can
pass coolant and the method used (Off, Flood, Mist or Air).
The Through Coolant option in the Milling Cutter Spindle
Parameters has been enhanced to provide a High Pressure
selection.
Note: The new options will only be available when using
updated Post Processors.
Licensing
This document contains a list of bug fixes and enhancement requests implemented in
Edgecam 2014 R1 SU1.
For new features and enhancements in this release, please refer to What’s New in Edgecam
2014 R1.
The ID column in the report lists the development task number associated to the item and
you also find these listed against your original support call in the Customer Support Portal.
Edgecam 2014 R1 SU1 Maintenance Database Report
• This document contains a list of bug fixes and enhancement requests implemented in Edgecam 2014 R1 SU1.
• For new features and enhancements in this release, please refer to What’s New in Edgecam 2014 R1 SU1.
• The ID column lists the development task number associated to the item. This is also listed against your original support call in the Customer Support
Portal.
40166 Angled Head - Internal simulation has tool wrongly oriented Fixed.
40313 Angled Head - Use of Tool Graphic causes incorrect simulation Fixed.
40587 Roughing - 3D Stock or Update Stock will gouge the part Fixed.
53686 Spindle Docking - Generates a new STL Model at each regen Fixed.
59813 Internal Simulation - Wrong orientation using tool with solid holder (.meg/.stl) Fixed.
61088 Profiling - Toolpath changes if a comment is placed before the cycle Fixed.
61467 Generate NC Code on foreign system (Turkish) with special characters causes Fixed.
errors
61572 Fixture Manager - ShowFixturePreviewWindow issue Fixed.
61579 Ribbon Bar - Removing PCI commands from the Tools menu crashes Edgecam Fixed.
61594 Graphics - Surfaces do not highlight when picked or with intellisnap Fixed.
61710 Workflow Create Sequence - Sequence does not initialise properly Fixed.
61787 SIMSDK - Document changes since 2013R1 in the readme file Fixed.
61798 3D Normal Offset Output - License required listed in What's New Fixed.
61976 Help file - JavaScript error when using tab links in IE 11 Fixed.
Maintenance Database
Report
Edgecam 2014 R1 SU2
This document contains a list of bug fixes and enhancement requests implemented in
Edgecam 2014 R1 SU2.
For new features and enhancements in this release, please refer to What’s New in Edgecam
2014 R1.
The ID column in the report lists the development task number associated to the item and
you also find these listed against your original support call in the Customer Support Portal.
Edgecam 2014 R1 SU2 Maintenance Database Report
• This document contains a list of bug fixes and enhancement requests implemented in Edgecam 2014 R1 SU2.
• For new features and enhancements in this release, please refer to What’s New in Edgecam 2014 R1 SU2.
• The ID column lists the development task number associated to the item. This is also listed against your original support call in the Customer Support Portal.
53686 Spindle Docking - Generates a new STL Model at each regen - file size build up. Fixed.
57585 Code Generator and Synchronise command - flag to identify if coming from Sync, A new system variable SYNCFROMUPDATESTOCK is now set to 1 at the sync
Update Stock or Balanced Cycle. point when it was generated from an Update Stock. The user can construct
logic from that to skip unwanted sync points.
60552 New Dialogs - Machining cycles are not allowing for Model Type changes. Fixed.
61734 Simulator - toolkit lower turret reverse axial tool holders are initially shown in axial Fixed.
orientation.
61811 Profiling - Cycle changes side when regenerated. Fixed.
61911 What's new help to include information about workflow strategy improvements. Implemented.
62053 User Interface - View Clipping - Wrong behaviour with positive/negative values. Fixed.
62070 Workflow Chuck fixtures - They do not work without turning or production license. Fixed.
62099 Spindle docking duplicates stock each time the sequence is regenerated. Fixed.
62112 Code Wizard - allow 'driven spindle' component to be moved again in the tree. Fixed.
62290 Instruction Sequence - Regen is slower on sequence with several instructions. Fixed.
62400 User Interface - View Clipping - Does not select internal faces. Fixed.
62473 Manual Features - Profile from Edges - cannot pick vertices from Fixed.
copied/transformed Solid.
62504 Job names containing Chinese characters are not displayed correctly in Live Job Fixed in the new 2014 R1 SU2 installation file set for Live Job Reports.
Reports.
62505 Turn Sequence - Moving an Update Stock instruction from a 2 turret machine to a 1 Fixed.
turret.
62512 Profiling - When Z offset takes path above level, Arcs are output as linear moves. Fixed.
62517 Simulator - index move is not simulated correctly and destroys the part. Fixed.
62609 Strategy Manager - output process crashes with PDI commands. Fixed.
62908 Live Job Reports - language pack under \custom_files folder is not installed when Fixed. New Live Job Reports setup has to be included on the DVD file set.
LJR setup.exe is called from the Edgecam installation program.