Professional Documents
Culture Documents
2011 ELECTRICAL
DESCRIPTION
DESCRIPTION
This group covers the various standard and optional power distribution components used on this model. The
power distribution system for this vehicle consists of the following components:
cardiagn.com
Power Inverter Module
115 Volt Power Outlet
The power distribution system also incorporates various types of circuit control and protection features,
including:
Following are general descriptions of the major components in the power distribution system. Refer to the
owner's manual in the vehicle glove box for more information on the features and use of all of the power
distribution system components. Refer to Wiring Diagrams for complete circuit diagrams.
For specific fuse location and types, refer to FUSE LOCATIONS AND TYPES , SPECIFICATIONS .
OPERATION
OPERATION
The power distribution system for this vehicle is designed to provide safe, reliable, and centralized distribution
points for the electrical current required to operate all of the standard and optional factory-installed electrical
and electronic powertrain, chassis, safety, security, comfort and convenience systems. At the same time, the
power distribution system was designed to provide ready access to these electrical distribution points for the
vehicle technician to use when conducting diagnosis and repair of faulty circuits. The power distribution system
can also prove useful for the sourcing of additional electrical circuits that may be required to provide the
electrical current needed to operate accessories that the vehicle owner may choose to have installed in the
aftermarket.
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
FUSE, IOD
DESCRIPTION
DESCRIPTION
All vehicles are equipped with an Ignition-Off Draw (IOD) fuse that is disconnected within the Integrated
Power Module when the vehicle is shipped from the factory. Dealer personnel are to reconnect the IOD fuse in
the Integrated Power Module as part of the preparation procedures performed just prior to new vehicle delivery.
The IOD fuse can be removed to avoid discharging the battery by disconnecting non-essential, low-current
memory functions that are normally on at all times. A detent on the IOD fuse holder allows it to be stored in its
normal cavity but out of contact. The holder is pushed into place to restore power to the systems it supplies. The
following circuits are protected by the IOD fuse:
cardiagn.com
Cluster (CCN)
Electronic Overhead Module (EOM
Sentry Key Remote Entry Module (SKREEM)
Video Module (DVD system)
Hands Free Telephone Module
Map Lamps
Glove Box Lamp
Courtesy Lamps
Radio
Security Module (export markets)
Traffic Control Module (export markets)
OPERATION
OPERATION
The term ignition-off draw identifies a normal condition where power is being drained from the battery with the
ignition switch in the Off position. The IOD fuse feeds the memory and sleep mode functions for some of the
electronic modules in the vehicle as well as various other accessories that require battery current when the
ignition switch is in the Off position. The only reason the IOD fuse is disconnected is to reduce the normal IOD
of the vehicle electrical system during new vehicle transportation and pre-delivery storage to reduce battery
depletion, while still allowing vehicle operation so that the vehicle can be loaded, unloaded and moved as
needed.
The IOD fuse is disconnected from Integrated Power Module when the vehicle is shipped from the assembly
plant. Dealer personnel must reconnect the IOD fuse when the vehicle is being prepared for delivery in order to
restore full electrical system operation. Once the vehicle is prepared for delivery, the IOD function of this fuse
becomes transparent and the fuse that has been assigned the IOD designation becomes another Fused B(+)
circuit fuse.
The IOD fuse can be used by the vehicle owner as a convenient means of reducing battery depletion when a
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
vehicle is to be stored for periods not to exceed about thirty days. However, it must be remembered that
disconnecting the IOD fuse will not eliminate IOD, but only reduce this normal condition. If a vehicle will be
stored for more than about thirty days, the battery negative cable should be disconnected to eliminate normal
IOD; and, the battery should be tested and recharged at regular intervals during the vehicle storage period to
prevent the battery from becoming discharged or damaged.
REMOVAL
cardiagn.com
Fig. 1: Two Retainers, Electrical Connector & Power Inverter Module
Courtesy of CHRYSLER LLC
INSTALLATION
INSTALLATION
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
cardiagn.com
Fig. 2: Two Retainers, Electrical Connector & Power Inverter Module
Courtesy of CHRYSLER LLC
DESCRIPTION
For more information, refer to MODULE, TOTALLY INTEGRATED POWER (TIPM) , DESCRIPTION .
OUTLET, POWER, 12 V
DESCRIPTION
DESCRIPTION
This vehicle is equipped with three 12-volt electrical outlets. The outlets are located in the following locations:
The cargo area and center stack power outlets have power at all times, and include tethered covers. The cigar
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
lighter outlet located in the center stack is on with the ignition switch in the Run/ACC position only.
REMOVAL
REMOVAL
cardiagn.com
Fig. 3: Inserting Power Outlet Remover
Courtesy of CHRYSLER LLC
INSTALLATION
INSTALLATION
cardiagn.com
Fig. 5: Identifying Wiring Harness And Power Outlet
Courtesy of CHRYSLER LLC
1. Connect the wire connector (1) to the power outlet receptacle (2).
2. Install the power outlet mount into the panel.
3. Align the splines on the outside of the power outlet receptacle base connector receptacle with the grooves
on the inside of the mount.
4. Press firmly on the power outlet receptacle base until the retaining bosses of the mount are fully engaged
in their receptacles.
5. Connect the battery negative cable.
DESCRIPTION
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
cardiagn.com
Fig. 6: View Of Center Floor Console Rear Trim Panel
Courtesy of CHRYSLER LLC
The 115 Volt AC outlet (3) is mounted in the rear of the center floor console (2). The vehicle is able to supply
115 Volt AC power through the use of a inverter module. The inverter module is located under the right rear
seat cushion. The inverter converts the 12 Volt DC from the vehicle battery system to a 115 Volt AC output.
The inverter module provides A/C power for user accessories when the 115 Volt AC outlet switch (4) in the
instrument panel center stack is in the "ON" position. The outlet switch is part of the instrument panel upper
switch pod assembly and is not available for service as an individual part. If the switch is damaged or
inoperative the complete upper switch pod assembly must be replaced, for the appropriate procedure, refer to
POD, SWITCH , REMOVAL .
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
OPERATION
OPERATION
The 115 volt AC power outlet switch receives 12 volts from the Integrated Power Module (IPM) and passes it
as an enable signal to the inverter module. The inverter module also receives 12 volts via the IPM and inverts
this to a 115 volt AC output. The enable signal received from the power outlet switch enables the inverter to
convert the received voltage and pass it to the power outlet to power external devices.
INVERTER MODULE
cardiagn.com
WARNING: Disable the airbag system before attempting any steering wheel, steering
column, seat belt tensioner, side airbag or instrument panel component
diagnosis or service, refer to WARNING . Disconnect and isolate the
negative battery (ground) cable. Wait two minutes for the airbag system
capacitor to discharge before performing further diagnosis or service.
This is the only sure way to disable the airbag system. Failure to follow
these instructions may result in accidental airbag deployment and
possible serious or fatal injury.
REMOVAL
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
REMOVAL
cardiagn.com
Fig. 8: Rear Center Console Bezel & Retainers
Courtesy of CHRYSLER LLC
4. Disconnect the electrical connector (1) for the 115v power outlet (2).
5. Release the clips holding the 115v power outlet and push through the panel.
INSTALLATION
2011 Jeep Grand Cherokee
2011 ELECTRICAL Power Distribution - Grand Cherokee
INSTALLATION
cardiagn.com
Fig. 10: Electrical Connector & 115v Power Outlet
Courtesy of CHRYSLER LLC