Professional Documents
Culture Documents
cutting machine
FQL-450L
Operating instruction
I.An overview
Automatic film sealing and cutting machine, automatic unmanned
the film guide system and the feeding platform for products of different
This machine is mainly used for batch heat shrink packing of cosmetics,
and plastic, etc. It can be used together with jet heat shrink packing
benefit and easy operation. This machine is suitable for POF heat shrink
saving the packaging cost, The goods packed by this shrink machine will
第1页
II. Product features
1. Sealing cutter uses Teflon coating anti-stick high temperature
aluminum alloy knife, sealing edge will not crack, not coking, no smoke
and pollution.
(4) Device of install shrink film (5) shrink film fixing rod (6) pull film clutch
handle (7) circular shaft (8) Shrink film opening triangle plate (top) (9)
conveyor belt (10) Pause switch (11) Cover (12) Shrink film open triangle
第2页
plate (bottom) (13) handwheel width adjustment (14) photoelectric eye
(16) sealing knife (top) (17) traction motor (18) switch for waste
(21) micro switch action plate (22) Film feeding balance bar (adjustable
up and down)
第3页
电源
横封温度 纵封温度 封切时间 行程设定 计数器
手动 自动
(1) Main power supply: the main power switch of the equipment.
(3) Mode selection: Turn left to "manual" mode, turn right to "automatic"
mode.
sealing cutter.
sealing cutter.
(6) Sealing and cutting time: set the sealing and cutting time of the cutter.
(7) Stroke setting: Set the sealing and cutting time after the packaging
第4页
The auxiliary buttons on the conveying table of equipment from left to
right are film feeding button, sealing and cutting button, emergency stop
button. The film feeding button and sealing and cutting button can only be
used in manual mode, and the emergency stop cannot replace the power
switch.
V. Directions of use
part of the shrink film will be. If the time is set too long, it may make the
shrink not beautiful (the shrink film on the packaging surface will produce
time is too short, the horizontal sealing cutter may cut into the packaged
the packaging is different, the time is not the same, need adjusting
carefully.
第5页
The longer the horizontal sealing time is set, the longer the horizontal
sealing cutter will cut off. If the setting time is too long, the packaging film
may melt or stick to the knife, causing unnecessary trouble. If the setting
time is too short, the packaging film may not be cut off, affecting the
thickness of the packaging material is different, the time is not the same,
(3)counter of packaging
When the package goes through the electric eye switch and the sealing
cutter drops and rises again, the number on the package counter will
increase by one (the number on the counter will return to zero, press the
第6页
"count clear" button below).
conveyor belt)
When the packing object passes through the photoelectric sensor, the
stroke setting device is activated, and the sealing cutter is lowered to seal
must be selected. At this time, the conveyor belt does not run and the
at this time the conveyor belt operation, electric eye start. When the
package touches the electric eye, the sealing cutter will drop
automatically. Please be careful not to touch the electric eye and sealing
第7页
cutter with your hands.
第8页
(6)Sealing and cutting temperature
Usually the horizontal sealing cutter is set at about 180°C-200°C, and the
(7) Cylinder
Drain the water at least once a month (close to the white button below
the cylinder, the water will come out) and check the oil at least once a
month.
oil
White button
第9页
3, access 220v power supply, open the power switch, at this time the
4. Adjust the position of the supply conveyor belt, so that the packaging is
5. Adjust the height of the triangle board slightly higher than the height of
the packaging.
6. Hold the opening side of the folded shrink film by hand, and then lead
it into the entrance of the traction chain. Press the button of film feeding
on the table with the other hand, and the film will lead into the longitudinal
7. After the film is introduced into the vertical sealing mechanism, if the
heating temperature has reached the set value, you can manually seal
and cut by pressing the sealing and cutting button on the table. (Manual
When the length of waste side material is enough, the material head can
第 10 页
VII. Film loading and film adjusting
methods
第 11 页
1. Way of Film loading
Figure 4
Lower film: the balance bar is adjusted upward, and the lower film is
moved inward: the balance bar is moved downward to adjust, the lower
第 12 页
Note: the upper and lower positions of the film feeding lever are more
balanced.
Voltage 220V/50HZ
Working 780+50mm
platform height
Work efficiency 15-30pcs/min/ according to the product
Dimension L1550×W790×H1470 mm
第 13 页
Monkey wrench pcs 1
socket head wrench pcs 1
plug pcs 1
第 14 页
第 15 页
第 16 页
Ma
第 17 页
Manufacturer Certificate
Dear customers,
email. We will make a serious treatment and reply to your sincere help us
第 18 页
Warranty Card
Product name Automatic film sealing Purchasing date
and cutting machine
Product model FQL-450A Customer name
Warranty description:
1, The main engine warranty for one year, electrical part warranty for one year.
2. No warranty for wearing parts and consumables.
3. Improper operation and man-made damage are not within the warranty scope.
第 19 页