Professional Documents
Culture Documents
Uses Dosage
To increase the workability and/or strength of concrete of a The optimum dosage of Conplast R to meet specific
given cement content whilst increasing its initial and final requirements should always be determined by trials using
setting time. To facilitate the production of high quality the materials and conditions that will be experienced in use.
concrete of improved durability and water tightness. The normal dosage range is 0.3 to 0.6 litres/100 kg of
cementitious material, including PFA, GGBFS or microsilica.
Advantages
Use at other dosages
! Set retardation allows extra placing time for larger pours.
Dosages outside the normal range quoted above can be
! Increased workability facilitates placing and compaction. used to meet particular mix requirements. Contact Fosroc
! High strengths without increase in cement content or for advice in these cases.
reduction in workability.
Effects of overdosing
! Strength specifications and workability can be maintained
with less cement. An overdose of double the intended amount Conplast R will
result in a significant increase in retardation as compared to
! Set retardation controls stiffening time of concrete in hot
that normally obtained at the intended dosage. Provided that
weather.
adequate curing is maintained, the ultimate strength of the
concrete will not be impaired by increased retardation and
Standards compliance
will generally be increased.
Conplast R conforms with BS 5075 Part 1, ASTM C494
The effects of overdosing will be further increased if sulphate
Type D and BSEN 934-2.
resisting cement or cement replacement materials are used.
Description
Properties
Conplast R a brown chloride free liquid is based on a
hydroxycarboxylic acid derivative which instantly disperses Appearance : Brown liquid
in water. Specific gravity
(BSEN 934-2) : 1.14 @ 22°C + 2°C
Conplast R disperses the fine particles in the concrete mix, Water soluble chloride
enabling the water content of the concrete to perform more (BSEN 934-2) : Nil
effectively. This effect can be used to improve workability, to Alkali content : Typically less than 30g. Na2O
increase ultimate strengths or to facilitate a reduction in the (BSEN 934-2) equivalent/litre of admixture
cement content.
The retarding properties of Conplast R can also be beneficial Instructions for use
in concrete where high cement content or high temperatures Retardation
are involved. Cold joints in continuous pours may be avoided
and the use of lower cement contents will reduce heat of The level of retardation obtained may be varied by altering
hydration. the dosage of Conplast R used, this will also alter the level of
water reduction obtained. Retardation is also affected by
Conplast R is particularly suitable for cohesive and cement factors other than the admixture, depending on the mix details
rich mixes. For lean mixes which are prone to segregation and conditions involved. Major factors include the following:
Conplast RP264*† may prove more suitable.
a) Cement replacement materials and SRC cements will
Technical support usually give greater levels of retardation than concrete
mixes made with ordinary Portland cement at the same
Fosroc provides a technical advisory service for on-site admixture dosage. Trials need to be conducted to
assistance and advice on mix design, admixture selection, establish the required dosage.
evaluation trials and dispensing equipment.
Conplast R*
Conplast R*
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard
Conditions for the Supply of Goods and Service
Head Office
Al Gurg Fosroc telephone: (+9714) 2858606 fax: (+9714) 2859649 email: agf@fosroc.com
LLC Regional offices
Dubai, Al Gurg Fosroc telephone: 285 8787 fax: 285 2023 email: dubai@fosroc.com
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17735454 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
www.fosroc.com
Oman, Al Amana telephone: 771 5080 fax: 771 7554 email: oman@fosroc.com
Qatar, Tadmur telephone: 413628 fax: 440812 email: qatar@fosroc.com
UAE/0276/01/D