Professional Documents
Culture Documents
To provide excellent acceleration of strength again at Fosroc provides a technical advisory service for on-site
early ages and major increases in strength at all ages by assistance and advice on mix design, admixture selection,
significantly reducing water demand in a concrete mix. evaluation trials and dispensing equipment.
Particularly suitable for pre-cast concrete and other high Typical dosage
early strength requirements.
The optimum dosage of Conplast SP430SA to meet specific
To significantly improve the workability of site mixed and requirements should always be determined by trial mixes
pre-cast concrete without increasing water demand. using the materials and conditions that will be experienced
To provide improved durability by increasing ultimate in use.
strengths and reducing concrete permeability.
For high strength, water reduced concrete the normal
dosage range is from 0.7 to 2.0 litres per 100 kg of
Advantages cementitious material, including PFA, GGBFS and micro-
silica. For high workability concrete the normal dosage
Major increases in strength at early ages without range is from 0.7 to 1.3 litres per 100 kgs of cementitious
increased cement contents are of particular benefit in material.
pre-cast concrete, allowing earlier stripping times.
Use at other dosages
Makes possible major reductions in water/cement ratio
which allow the production of high strength concrete Dosages outside the typical ranges quoted above can be
without excessive cement contents. used to meet particular requirements. Contact Fosroc for
advice.
Use in production of flowing concrete permits easier
construction with quicker placing and compaction and
reduced labour costs without increasing water content. Properties
Increased workability levels are maintained for longer Appearance: Brown liquid
than with ordinary sulphonated melamine admixtures. Specific gravity: o
Typically 1.155 at 20 C
Improved cohesion and particle dispersion minimises Chloride content: Nil to BS 5075
segregation and bleeding and improves pumpability. Air entrainment: Typically less than 2% additional
air is entrained at normal dosages.
Chloride free, safe for use in pre-stressed and reinforced Alkali content: Typically less than 72.0 g Na2O
concrete. equivalent/litre of admixture. A
fact sheet on this subject is
available.
Standard compliance
Conplast SP430SA complies with BS 5075 Part 3 and with Instructions for use
ASTM C494 as Type A and F depending on dosage used.
Mix design
Description
Where the main requirement is to improve strength, initial
trials should be made with normal concrete mix designs.
Conplast SP430SA is a chloride free, superplasticising
The addition of the admixture will allow the removal of water
admixture based on selected sulphonated naphthalene
from the mix whilst maintaining workability. After initial
polymers. It is supplied as a brown solution which instantly
trials, minor modifications to the overall mix design may be
disperses in water. Conplast SP430SA disperses the fine
made to optimise performance.
particles in the concrete mix, enabling the water content of
the concrete to perform more effectively. The very high
Where the main requirement is to provide high workability
levels of water reduction possible allow major increases in
concrete, the mix design should be one suitable for use as a
strength to be obtained.
pump mix. Advice on mix design for flowing concrete is
available from Fosroc.
Page 1
Conplast SP430SA
Compatibility Effects of overdosing
Conplast SP430SA is compatible with other Fosroc An overdose of double the amount of Conplast SP430SA
admixtures used in the same concrete mix. All admixtures will result in an increase in retardation as compared to that
should be added to the concrete separately and must not be normally obtained. Provided that adequate curing is
mixed together prior to addition. The resultant properties of maintained, the ultimate strength of the concrete will not be
concrete containing more than one admixture should be impaired by increased retardation and will generally be
assessed by trial mixes. increased. The effects of overdosing will be further
increased if sulphate resisting cement or cement
Conplast SP430SA is suitable for use with all types of replacement materials are used.
ordinary Portland cements and cement replacement
materials such as PFA, GGBFS and micro-silica. Over-dosage may also cause increased air entrainment
which will tend to reduce strength. The degree of this effect
Effects on stiffening and set. will depend on the particular mix design and overdose level.
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice,
recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous
control over where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products,
whether or not in accordance with any advice, specification, recommendation of information given by it.
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
FO SA/CONPLAST SP43OSA/16/01/10
Page 3