Professional Documents
Culture Documents
Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 966C WHEEL LOADER 76J
Configuration: 966C WHEEL LOADER 76J00001-06388 (MACHINE)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 2 of 10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 3 of 10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 4 of 10
start by:
a) remove axles
2. Remove the guards from under the engine and transmission with a floor jack. Weight of the engine
guard is 78 lb. (35.4 kg). Weight of the transmission guard is 200 lb. (90.7 kg).
4. Disconnect lines (2) from the quick release valve. Put identification on the lines for installation
purposes.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 5 of 10
11. Lift the rear of the machine evenly with tooling (A). Push the front and rear supports away from
the frame with a bar.
13. Remove the rear axle housing and supports from under the machine.
15. Fasten a hoist and remove the front support (5). Weight of the front support is 75 lb. (34 kg).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 6 of 10
16. Turn the axle housing until the rear support is up.
19. Remove the bolts (7), locks (9) and plate (8) holding the support to the trunnion.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 7 of 10
1. Put the rear support (1) in position on the trunnion (2) with a hoist.
2. Install the plate, locks, bolts, and cover, holding rear support to the trunnion.
3. Turn the axle housing until the carrier assembly is up as shown and install the front support with a
hoist.
4. Release the brakes on the rear wheels. Connect a floor jack to the rear support.
5. Put the rear axle housing and wheels as a unit into position under the machine.
9. Put the front and rear supports in alignment with the frame.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 8 of 10
10. Install the bolts (6) holding the front and rear supports to the frame.
11. Remove the air lines (5). Connect the air lines (4) to the quick release and holding valve (3).
12. Install the drive shaft (8). Tighten the bolts (7) to 98 ± 10 lb.ft. (134 ± 14 N·m).
13. Install the guards under the engine and transmission with a floor jack.
end by:
a) install axles
start by:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documentation Page 9 of 10
1. Remove seals and ring (1) from the front support for rear axle housing.
2. Remove bearing (2) with tooling (A) from the front support for the rear axle housing.
3. Remove seal and bearing from rear supports with tooling (A).
1. Install bearing in the front support even with face of support with a press and tool (A). Install a
spacer 7.375 in. (18.7 cm) outside diameter 1 in. (2.54 cm) thick under tool (A) and push the bearing
into the correct position in support.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023
966C WHEEL LOADER 76J00001-06388 (MACHINE)(UE070090 - 00) - Documenta... Page 10 of 10
3. Install seals (1) with tool (A). The lip of seal must be toward the outside of support.
5. Install seal in rear support with tool (A). The lip of seal must be toward the outside of support.
6. Put grease on the outside diameter of the bearings and on the lip of the seals before installation.
end by:
Copyright 1993 - 2023 Caterpillar Inc. Fri Apr 7 17:20:19 UTC-0400 2023
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 7/4/2023