Professional Documents
Culture Documents
NORMAS Iso Sin Ordenar10816 Charts-Feb2021
NORMAS Iso Sin Ordenar10816 Charts-Feb2021
ISO 10816 has been one of the first and mostly developed standards for vibration
evaluation of machinery including different type of machinery like wind turbine, hydro
turbine, gas turbine & steam turbines, reciprocating machinery, etc.
ISO 10816-1
Critical Machines
ISO 10816-3 is mainly applied to vibration measurement of industrial machines like electro
motors powered above 15 KW and speed range (120 RPM-15000RPM)
by accelerometer or velocity transducers on fixed parts like bearing housings
Gas Turbines
ISO 10816-4 is mainly applied to vibration measurement of land based gas turbine with
speed range (3000 RPM-20000RPM) by accelerometer or velocity transducers on fixed
parts like bearing housings/ pedestals
NOT: These Values, Which are the upper limits of zone A,B and C Respectively, Should
apply to radial vibration measurements on all bearing housings or pedestals and to axial
vibration measurements on housings containing an axial thrust bearing, under steady-state
operating conditions at rated speed.in this figure shows typical measurement positions.
Hydro Turbine
This part of ISO 10816 gives guidelines for applying bearing housing vibration evaluation
criteria measured under normal operating conditions at the bearings, bearing pedestals or
bearing housings of the main machine sets in hydraulic power generating and pumping
plants. ISO 10816-5 is applicable to machine sets with speeds from 60 r/min to 1800 r/min,
shell or shoe type sleeve bearings and a main engine power of 1 MW and more. The
position of the shaft line may be vertical, horizontal or at an arbitrary angle between these
two directions.
ISO10816-6
Reciprocating Machinery
ISO 10816-6 specifies the general conditions and procedures for the measurement and
evaluation of vibration, using measurements made on the non-rotating and non-
reciprocating parts of reciprocating machines. It generally applies to reciprocating piston
machines mounted either rigidly or resiliently with power ratings of above 100 kW. Typical
examples of application are: marine propulsion engines, marine auxiliary engines, engines
operating in diesel generator sets, gas compressors and engines for diesel locomotives. The
general evaluation criteria which are presented relate to both operational monitoring and
acceptance testing. They are also used to ensure that the machine vibration does not
adversely affect the equipment directly mounted on the machine.
ISO10816-7
Pump
ISO 10816-7 gives instructions for the evaluation of vibration on rotary pumps for
industrial applications with nominal power above 1 kW. It defines the special requirements
for evaluation of vibration when the vibration measurements are made on non-rotating parts
(bearing housing vibration). It provides specific guidance for assessing the severity of
vibration measured on bearing housings of rotary pumps in situ and for the acceptance test
at the manufacturer’s test facility or in the plant.
This part of ISO 10816 also gives general information and guidelines for assessing relative
shaft vibration of the rotating shaft.
This part of ISO 10816 specifies zones and limits for the vibration of horizontal and
vertical pumps irrespective of their support flexibility. Additionally, recommendations are
given for defining operational limits and setting alarm and trip values.
ISO10816-8
Reciprocating Compressors
This part of ISO 10816 establishes procedures and guidelines for the measurement and
classification of mechanical vibration of reciprocating compressor systems. The vibration
values are defined primarily to classify the vibration of the compressor system and to avoid
fatigue problems with parts in the reciprocating compressor system, i.e. foundation,
compressor, dampers, piping, and auxiliary equipment mounted on the compressor system.
This part of ISO 10816 applies to reciprocating compressors mounted on rigid foundations
with typical rotational speed ratings greater than 120 r/min and up to and including 1800
r/min. The machinery driving the reciprocating compressor, however, is evaluated in
accordance with the appropriate part of ISO 10816 or other relevant International Standards
and classification for the intended duty. Examples of reciprocating compressor systems
covered by this part of ISO 10816 are
compressors driven by electric motors, gas, and diesel engines, steam turbines, with or
siting onshore, Installation on supporting systems (tower and foundation) made of steel and
concrete, horizontal-axis rotor with several rotor blades, rotor bearing separate from or
integrated into the gearbox, generators driven via gearbox, generators of the synchronous or
asynchronous type with only a fixed pole number or which are pole-changeable for speed
adjustment, generator coupled to the power grid via converter or directly