Professional Documents
Culture Documents
AMENDMENT
STANDARD PRACTICE
o
N
o
N
Õ
M
""
~
§
O
This document contains changes that were approved by the AIA Nondestructive Testing Subcommittee (NDTSC) and Quality
u Assurance Committee (QAC) on October 26,2020. These changes facilitate production during the COVID-19 pandemic
~ restrictions in place by global government agencies and are intended to be transitory during this period. These changes may
6 be immediately implemented upon release and will be valid until such time that this amendment is withdrawn. Revision of the
s::E employer's written practice per section 4.1 to incorporate these changes is not required.
-c
u,
o
z
o
~
oo
Vl New Section added after 8.3.1:
~
Vl
W
I. When extensions are applied per 8.3.1.1: new expiration date, justification, and approval by the Responsible
Levei 3 or designated Examiner for each extension applied.
REVISION
5 AMENDMENT
NAS410
SHEET 2
Copy'igh!Aemspace Indus!ries ,l.§IicQlfoPIlt~/;W';;~. nusUPON DOCUMENT OR ANY NATIONAL AEROSPACE ST~h'lIdnl~'IImlIi~'(6VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Proviõed by IHS Ma"';! under ,;~~U OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD~"oéJAJd'!l!(fili1i0JllffllRiSfiNfMW~!GIi6t;\a\iM1~iIldE~1lID' OF
No reproducton 01 netwo"';ng MiftiM!! jO~<1'AIIt'fdOOl>A.R APPLICATION OR (2) lHE EXISTENCE OF OR APPLIC"8I"",,,_Q1~ fI'1I'Il:lIWUR TRADEMARKS RIGHTS.
© COPYRlGHT 2020
NATIONAL AEROSPACE STANDARD
AEROSPACE INDUSTRlES ASSOCIATION OF AMERlCA, INC. ALL RlGHTS RESERVED
fi1m
NATIONAL AfllOSPACE STANDARDS
STANDARD PRACTICE
THIRD
ANGLE --@-E3- CUSTODIAN
QUALITY ASSURANCE COMMITTEE
REVISION
5
PROJECTION
PROCUREMENT TITLE CLASSIFlCATION
SPECIFICATION STANDARD PRACTICE
NAS CERTIFICATION &. QUALIFICATION OF
NONE NONDESTRUCTIVE TEST PERSONNEL
NAS410
SHEET 1 OF 29
TABLE OF CONTENTS
1. SCOPE 6
1.1 PURPOSE 6
1.2 APPLICABILITY 6
1.2.1 IMPLEMENTATION 6
1.3 METHODS 6
1.3.1 COMMON METHODS 6
1.3.2 OTHER METHODS 6
2. NORMATIVE REFERENCES 7
2.1 STANDARDS 7
2.2 ORDER OF PRECEDENCE 7
REVISION
5
NAS410
SHEET 2
eopy,ight Aerospace fndusjries ).§&Q!'oPIlt JijibWl!;;~. UPON THIS DOeUMENT OR ANY NATIONAL AEROSPACE ST,~l/J;)nl~~~~y8VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Provided by tHS Marl<itunde,ti~~ OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD~"'ot!JItoHIt'Im!l:N0~Rl!f6fiNTt!IiIW!H'lIi6(_,~ffldE~éfi(1lI{Y OF
No reproducton DO networl<ingP<I'!'IiM!!f'~N'I!ojOAR~wtJI>AR APPUCATION OR (2) THE EXISTENCE OF OR APPLICl~I!JMN~OlOl'l PA'IlIN'NJR TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INOUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVE O NATIONAl AEROSPACE STANDAROS
3.30 PROCEOURE 10
3.31 QUALIFICATION ...........................................................................................................•......... 10
3.32 RESPONSIBLE LEVEL 3 10
3.33 SPECIFIC EXAMINATION 10
3.34 SUB-CONTRACTOR 10
3.35 TASK 10
3.36 TECHNIQUE 10
3.37 TEST SAMPLE 10
3.38 WORK INSTRUCTION 11
3.39 WRmEN 11
3.40 WRmEN PRACTICE 11
4. GENERAL REQUIREMENTS 11
4.1 WRmEN PRACTICE 11
4.1.1 QUALIFlCATION ANO CERTIFICATION 11
4.1.2 AoomONAL REQUIREMENTS 11
4.1.3 NOT TECHNIQUES 11
4.1.4 TRAINING OUTUNES 12
4.1.5 EXAMINATION PRACTICES 12
4.1.6 AOMINISTRATION 12
4.1.7 RECOROS 12
4.2 METHOOS 12
4.3 RESPONSIBILfTY 12
4.3.1 GENERAL 12
4.3.2 RESPONSIBLE LEVEL 3 12
4.3.3 OUTSIOE AGENCY 13
REVISION
~ 5
;
NAS410
SHEET 3
Jt\i~!W,;;g.UPON THIS DOCUMENT OR ANY NATIONALAEROSPACE ST.~llJ;lnlSeF.ftIHilIi~yBVOLUNTARY. AlA DOES NOT QUALlFY SUPPLIERS OR CERTlFY
CopyrighlAerospace tndustríesAJ,1&:hl1foPIIt
Prcvrdec by IHS Ma.H under ti~ DF ITEMS PRODUCED UNDER NATIONALAEROSPACE STANDARD:iloéltê:',U!~fj!cNf'l"ifRi!f6fiNfMlÃl[ll'OIi6~~llIdEtilJj(f •••IiiBR:Y DF
No reproductionor networking_l'lJR4to.N'I!<1IArna:l1lAR APPLlCATION OR (2) THE EXISTENCE DF OR APPLlCl~I!J_~010Jl J'A'Ill~R TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATlONAl AfROSPACf STANOAROS
6.2.2 EXAMINERS 16
6.2.3 INSTRUCTORS 16
6.2.4 OUTSIDE AGENCIES 16
6.3 EXPERIENCE 17
6.3.1 GENERAL 17
6.3.2 PREVIOUS EXPERIENCE 17
6.3.3 EQUIVALENT EXPERIENCE 17
6.4 EMERGING NDT METHODS 18
6.4.1 MINIMUM HOURS 18
6.4.2 LEVELS 1 AND 2 18
6.4.3 LEVEL 3 18
7. EXAMINATIONS 19
7.1 PURPOSE 19
7.1.1 GENERAL 19
7.1.2 VISION EXAMINATION 19
7.1.3 GENERAL EXAMINATION 19
7.1.4 SPECIFlC EXAMINATION 19
7.1.5 PRACTlCAL EXAMINATION 20
7.2 ADMINISTRATION OF EXAMINATIONS 21
7.2.1 GENERAL 21
7.2.2 ADMINISTRATION BY AN OUTSIDE AGENCY 21
7.2.3 SCORING 21
7.2.4 RE-EXAMINATION 21
8. CERTIFlCATION 21
8.1 GENERAL 21
8.2 RECORDS 21
8.2.1 MINIMUM REQUIREMENTS 21
8.2.2 RECORD AVAlLABILfTY 22
8.3 LOSS OF CERTIFlCATION 22
8.3.1 EXPlRATION 22
8.3.2 SUSPENSION 22
8.3.3 REVOCATION 22
8.4 REINSTATEMENT OF CERTIFlCATION 22
8.5 RECERTIFlCATION 23
8.5.1 LEVEL 1 AND LEVEL 2 23
8.5.2 LEVEL 3 23
8.5.3 HANDS-ON PRACTlCAL EXAMINATION 23
8.6 ANNUAL PROFICIENCY REVIEW 23
ANNEXES
REVISION
5
NAS410
SHEET 4
nus
Copyrigh' Aerospace rndusuíes A!lilichlli'ohllltIl.\ib/;wQ'. UPON DOCUMENT OR ANY NATIONAL AEROSPACE ST.~'IJ;lnlSe~~~y8VOLUNTARY. AlA DOES NOT QUALlFY SUPPLIERS OR CERTlFY
Prcvided by 'HS Mark;' under ';c~ OF lTEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD:So"'loêo~Njj)riEl'II!f8fiN]ilif!A)[lI~i6(IdIllM1~~1lldE~éfi(~ OF
No reproducuon or networkinç P<l'T'l!1I4!I "0R46.N'l'r1IA~1OJ1lAR APPLlCATION OR (2) TliE EXISTENCE OF OR APPLlCl~lIltffte!~'it;'{i"{110fl P1\~mt1J1'ITRADEMARKS RlGHTS.
NATIONAL AEROSPACE STANDARD
~
© eOPYRIGHT 2020 AEROSPAeE INDUSTRIES ASSOeIATION OF AMERIeA, INe. ALL RIGHTS RESERVED NATiONAL AEROSPACE STANDAROS
TABLES
REVISION
5
NAS410
SHEET 5
Copyrighl Aerospace tndustnes ~&:QIioP& ~Wlt;;g. UPON THIS DOCUMENTOR ANYNATIONALAEROSPACEsr,~ll.Qnl!.\,~ftIT;!!lIi~y8VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Provided by IHS Ma"''' under Ii~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACEsrANDARD:sot!J~M1I~fi!l;N0J1ifRi!f6fittfilillÃll\1!Oli6(idIlIM1~i!ldEt!Wà:êIililll{Y OF
No reproduction or netwo"'ing P'I11'I!M!l ~rAAmooêAR APPLICATIONOR (2) THE EXISTENCEOF OR APPLIeJI\I!J_!QERl11I'01OP PI\'Il!NfmR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRIGHT 2020 AEROSPAeE INDUSTRIES ASSOeIATION OF AMERIeA, INe. ALL RIGHTS RESERVED NATIONAl AER.OSPACE STANDARDS
1. SCOPE
1.1 PURPOSE
u This document establishes the minimum requirements for the qualification and certification of personnel performing
~ non-destructive testing (NDT), nondestructive inspection (NDI), or nondestructive evaluation (NDE) in the
6 aerospace manufacturing, service, maintenance and overhaul industries. For the purposes of this document, the
<2
~
«
term NDT will be used and will be considered equivalent to NDI and NDE.
u,
o
z
o In Europe, the term "approval" is used to denote a written statement by an employer that an individual has met
§ specific requirements and has operating approval. The term "certification" as defined in 3.2 is used throughout this
u
o
til standard as a substitute for the term "approval". Except when otherwise specified in the written practice,
~
til
certification in accordance with this standard includes operating approval.
~ ~
~ci~
::»N 1.2 APPLICABILITY
~~;;
UJ o z"
~~§ This standard applies to personnel using NDT methods to test and/or accept materiais, products, components,
tIl;:z
assemblies or sub-assemblies. This standard also applies to personnel: directly responsible for the technical
~8~
«~« adequacy of the NDT methods used, who approve NDT procedures andjor wark instructions, who audit NDT
facilities, or who provide technical NDT support or training.
This standard does not apply to individuais who only have administrative or supervisory authority over NDT
personnel ar to research personnel developing NDT technology for subsequent implementation and approval by a
certified Levei 3. Personnel performing specialized inspections using certain direct readout instruments as
determined by a Levei 3 certified in the method, do not require qualification or certification to this standard.
1.2.1 IMPLEMENTATION
This standard addresses the use of a National Aerospace NDT Board (NANDTB). NANDTBs are only used as
specified per Annex C and it is not mandatory to have such a board for compliance with this document. Personnel
certified to previous revisions of NAS410 or EN 4179 need not recertify to the requirements of this standard until
their current certification expires.
1.3 METHODS
This standard contains detailed requirements for the following common NDT methods:
When invoked by engineering, quality, cognizant engineering organization or prime contractor requirements, this
standard applies to other current and emerging NDT methods used to determine the acceptability or suitability for
intended service of a material, part, component, sub-assembly or assembly. Such methods may include, but are not
limited to, acoustic emission, neutron radiography, leak testing, holography, and shearography. The requirements
for personnel training, experience, and examination for these other methods shall be established in accordance with
6.4 and shall be documented by the employer.
REVISION
5
NAS410
SHEET 6
CopyrighlAerospace Induslrles~5cQlfo~!l< )iji\'WI,;;g. UPON nus DOCUMENTOR ANYNATIONALAEROSPACEsr,~lIQnls\'~I\Il;l,!lli~Y8VOLUNTARY. AIA DOES NOT QUALlFYSUPPLlERS OR CERTIFY
Prcvidedby IHSMar'" under IIc~ OF lTEMS PRODUCED UNDER NATIONALAEROSPACEsrANDARD:,soéliê:~rwItiORl!f8fiNfilil'W[lI~i6'llAllMl~~11ldE~éBlBll:Y OF
Noreproductlonor networ1<lngp<!lTll!MS
fI_N'I'rJOArnaJI>AR APPLlCATION OR (2) THE EXIS1ENCE OF OR APPLlCl~l!Jl.tfftê~OlOfl I'II'IllNltUR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. All RIGHTS RESERVED NATIONAL AEROSPACf STANOAROS
2. NORMATIVE REFERENCES
2.1 STANDARDS
u The following referenced documents are indispensable for the application of this documento For dated references,
~ only the edition cited applies. For undated references, the latest edition of the referenced document (including any
5 amendments) applies.
õ2
lU
:;:
«
u,
o EN 4179, Aerospace Series - Qualification and Approval of Personnel for Nondestructive Testing
z
o
§ ISO 9712, Non-destructive Testing - Qualification and Certification of NDT Personnel
u
o
'"
!{,l
ISO 18490, Non-destructive Testing - Evaluation of Vision Acuity of NDT Personnel
'"~ ~
~c5~
::»'" ORDER OF PRECEDENCE
offi< 2.2
~z>
wQz
~~§
"';:z
In the event of a conflict between the text of this document and the references cited herein, the requirements of
this document take precedence. Nothing in this document supersedes applicable laws and regulations unless a
ffi§~
«~« specific exemption has been obtained.
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological data bases for use in standardization at the following addresses:
An examination utilized to verify a Levei 3 candidate's knowledge of NDT methods used by the employer at a Levei
2 proficiency.
3.2 CERTIFICATION
A written statement by an employer that an individual has met the applicable requirements of this standard.
The engineering or NDT organization of the prime contractor, OEM (Original Equipment Manufacturer), or end user
authorized to make NDT-related decisions and give NDT-related approvals.
Meetings, conferences, symposia, seminars, trade association meetings, panels, etc. organized or sponsored by a
regional, national or international NDT organization or technical society. Foreign or international meetings qualify if
the sponsor(s) are national or international.
REVISION
5
NAS410
SHEET 7
}iji~/;Wr;;~
Copyriqht Aerospace tndustrtes ~Q/fohlllt UPON 11-115 DOCUMENTOR ANY NATIONALAEROSPACEST,~IfJ;l,J~~~~YBVOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Provlded by IHS Markllunder"~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~"'0t!J~~!IilERI!f6flN'fMWtlI,aa;(l.c1\1mj1~~i1ldE~êIi(BH;Y OF
No reoroducucn or networklng p_ "_lII'1!rjOAmotII;AR APPLICAll0N OR (2) THE EXISTENCEOF OR APPLICl~IiIJ:t1W>~01~ M'IllN'!tUR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAl AEROSPACE STANDAROS
Specific identifiable official activities of regional or national technical societies, committees or work groups, such as
round robins or individual studies, preparation of guidelines, appendices, specifications, recommended practices,
procedures, codes or standards, etc. Documentation may include memos or reports, drafts of committee output
documents, or official written comments submitted by the candidate on such documents.
When the observer is able to view the NDT process in a manner that permits uninterrupted, visual and verbal two-
way contact with the trainee.
Instruments that physically display measurements in dimensional or electrical units (e.g. inches, millimeters or
%IACS) either as digital readout or an analog display, such as a scale/pointer configuration, and do not require
special skills or knowledge to set up the instrument and do not involve adjusting signal displays such as gates,
delays, gain, or phase to obtain measurements. For example, common direct readout instruments include basic
ultrasonic thickness gauges without an oscilloscope display, and eddy current coating thickness gauges.
3.9 DOCUMENTED
3.10 EMPLOYER
An organization employing or contracting the services of one or more individuais who perform NDT. Self-employed
individuais are included in this definition.
3.11 EVALUATION
A review following interpretation of the indications noted during an NDT inspection to determine whether the
indications meet specified acceptance criteria or to determine the significance of the indication.
3.12 EXAMINATION
Formal, controlled, documented testing conducted in accordance with a documented written practice to verify a
candidate's visual capability, skill or knowledge of an NDT method.
3.13 EXAMINER
A Levei 3 certified to this standard and designated by the Responsible Levei 3 to administer ali or part of the
qualification process in the NDT method(s) in which the Examiner is certified.
3.14 EXPERIENCE
Actual performance of an NDT method conducted in the work environment resulting in the acquisition of knowledge
and skill. This does not include formal classroom training, but may include laboratory and on-the-job training as
defined by the employer's written practice.
3.15 FORMALEDUCATION
REVISION
5
NAS410
SHEET 8
Copynqht Aerospace todusntes ~oQ8t Jiji~Iiê.Il';;~.UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE ST,~IMlnl§e~~~Y8VOLUNTARY. AIA DOES NOT QUALIFY SUPPLlERS OR CERTIFY
Provided by 'HS Marl<itunder ti~Nü OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD~"'o"'~~ft~t!IiHÃlli!fli6'_~llldEli1JJléBI!!n.Y OF
No reoroductcn 0' networl<ing~ fi~tAAAAifOt:IflAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICI\B_~O'01l M'Ill~R TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NA1IONAl AEROSPACf SlANOARDS
3.16 FORMALTRAINING
An organized and documented program of learning activities designed to impart the knowledge and skills necessary
to be qualified to this standard. Formal training may be a mix of classroom, practical and programmed self-
instruction as approved by the Responsible Levei 3 or Examiner.
3.17 GENERALEXAMINATION
A written examination addressing the basic principies and theory of an NDT method.
3.18 INDICATION
The response or evidence of a condition resulting from an NDT inspection that requires interpretation.
3.19 INSTRUCTOR
An individual designated or approved by the Responsible Levei 3 or Examiner to provide training for NDT personnel.
3.20 INTERPRETATION
3.21 METHOD
One of the disciplines of nondestructive testing (e.g. ultrasonic, radiography, etc.) within which different techniques
mayexist.
An independent aerospace organization representing a nation's aerospace industry that is chartered by the
participating prime contractors and recognized by the nation's regulatory agencies to provide or support NDT
qualification andjor examination services in accordance with Annex C of this standard.
Radiographic imaging that does not use a film-based recording medium. Non-Film radiography includes, but may
not be limited to, Computed Radiography, Digital Radiography, Radioscopy, and Computed Tomography.
Training in the work environment to gain experience in learning instrument set-up, equipment operation, applying
the process, and recognition, interpretation and evaluation of indications under appropriate technical guidance.
An examination administered with access to specific reference material that is provided with or referenced in the
exam ination.
Written statement issued by the employer, based upon the scope of certification, authorizing the individual to carry
out defined tasks. Such authorization can be dependent on the employer having provided job or task-specific
training.
REVISION
5
NAS410
SHEET 9
CopyriqhtAerospace';n~~~;ri~S~oi;>iHliib~,~. UPON THIS OOCUMENT OR ANY NATIONAL AEROSPACE ST.'tM!AAlMlnl~~~ilY8VOLUNTARY. AIA OOES NOT QUALIFY SUPPLIERS OR CERTIFY
Providedby !HSMark;!under tic~ OF lTEMS PROOUCED UNDER NATIONAL AEROSPACE STANDARD;>SoéJoê:~tifRl!t6tiNfo!\if!Ã)[lI!Qit(1JAlIM1~ffldE~éliiBR:Y OF
No reprodoctlonor network;ngp_ fi_N-Y<1lAmotlIiAR APPLICATION OR (2) THE EXISTENCE OF OR APPLI(J~fil_~010Jl PA'IllNflUR TRADEMARKS RIGHTS.
© COPYRIGHT 2020
NATIONAL AEROSPACE STANDARD
AEROSPACE INDUSTRIES ASSOCIATION OF AME RICA, INC. ALL RIGHTS RESERVE O
ítm
NATIONAL AEROS'ACE STANOAROS
An independent company or organization outside the employer who provides NDT services to implement the
requirements of this standard, such as training and examination of NDT personnel. Consultants and self-employed
u
individuais are included in this definition.
=
<5 PRACTICALEXAMINATION
õ2 3.28
UJ
L
-c
"-O An examination to demonstrate an individual's ability to conduct an NDT method as used by the employer.
z
O Questions and answers need not be written, but a checklist must be used and observations and results must be
§ documented.
u
Sl!!,l
3.29 PRIME CONTRACTOR
An organization having overall responsibility for design, control and delivery of a system, component or product.
3.30 PROCEDURE
A written general "how to" instruction for conducting a given processo Procedures are then used to develop work
instructions, as defined in 3.38.
3.31 OUALIFICATION
The skills, training, knowledge, examinations, experience and visual capability required for personnel to properly
perform to a particular leveI.
3.32 RESPONSIBLELEVEL3
The Levei 3 designated by the employer with the responsibility and authority to ensure that the requirements of this
standard are met and to act on behalf of the employer.
3.34 SUB-CONTRACTOR
An organization responsible to the prime contractor for the manufacture or maintenance of aerospace products. For
the purposes of this standard, this includes suppliers and processors.
3.35
An activity for which Levei 3 certification is required, e.g. approval of an NDT Technique Instruetion or NDT
procedure.
3.36 TECHNIOUE
A part or image containing one or more known and documented natural or artificial discontinuities, flaws or
conditions used in the practical examination to demonstrate the candidate's proficiency in an NDT method. Test
REVISION
5
NAS410
SHEET 10
........................
Copyriqht tncustrtes ~Q/fohlllf
Aeroepace Jiji6/;Mlr;;~. UPON THIS DOCUMENT OR ANY NATIONALAEROSPACE ST!\~!lAAlIJdnl~~fl.IJ:i.!!R9y8VOLUNTARY.AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Prcvided by 'HS Markitunder hc~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACE STANDARD~,e;ot!llA~N0r1itff>i!t8ti!ff~flI'Oi6'ldMM1~TIldf1ID.f<fêJi!(~ OF
No reproductionor networktnçp<l'1'l!M!If'OR46.N'!!r1OA~I?AR APPLICATION OR (2) THE EXISTENCE OF OR APPLI(MJI1<::fftê~O''''' WI'll1N'ft.{J!l. TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. All RIGHTS RESERVED
~
NATiONAL AEROSPACf S1ANDARDS
samples can refer to actual hardware, fabricated test parts, or, when applicable, images of actual hardware such as
radiographs.
WRffiEN
WRffiEN PRACTICE
A document that describes an employer's requirements and methodology for controlling and administering the NDT
personnel qualification and certification processo
4. GENERALREQUIREMENTS
The employer shall develop and maintain a written practice for the qualification and certification of NDT personnel
that meets the requirements of this standard. The written practice shall address the procedural details necessary for
the employer to implement an NDT qualification and certification program and shall include the details of the NDT
qualification and certification process, including:
The written practice shall be approved by the Responsible Levei 3. The written practice shall be available for review
by the employer's customer(s) and regulatory agencies.
The written practice shall include any additional requirements levied by the employer or cognizant engineering
organization, such as additional certification levels or increased experience requirements.
The written practice shall include the specific technique(s) within each method and the actions to be taken
concerning additional training and experience, as well as the written and practical testing, when additional
techniques are introduced for a currently certified individual.
REVISION
5
NAS410
SHEET 11
CopyrightAerospace tndustrles~6d~!'o!;l1lt ~bWlh;~.UPON THIS DOCUMENT OR ANY NATIONALAEROSPACE ST,~'lJdnlSi,~W:fflll~Y8VOLUNTARY. AIA DOES NOT QUALlFY SUPPLlERS OR CERTIFY
Providedby IHSMarkltunder hc~~ OF lTEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD:JSoéJtAJAAt:fi!l:N!ill~Rl!fSfiN'fMJÁ)[ll<0Ii6[iD\lIM1~~1lldE~êliil3ll;Y OF
No reproducttonor networkinqpilT'E1l4!lflOOcAl\i!1!<1'ARf101Jt?AR
APPLlCATION OR (2) THE EXISTENCE OF OR APPLl(J~!I__ <l'EJ1d P1\'Il!~R TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRlGHT 2020 AEROSPAeE INDUSTRlES ASSOeIATION OF AMERleA, INe. ALL RlGHTS RESERVED W"TiONAL AfROSPACE STANDARDS
The written practice shall reference or include the NDT training outlines used by the employer. If an outside agency
is used to provide training, the Responsible Levei 3 shall verify that the training meets the employer's requirements.
The written practice shall include the designation of the individual(s) or organization(s) responsible for administering
examinations, the number of examination questions to be administered, and the specific visual acuity examination
method to be used. If required, the use of a general examination for recertification shall be documented in the
written practice.
4.1.6 ADMINISTRATION
The written practice shall include the identification of the individual(s) or organization(s) responsible for
administering and maintaining ali or part of the employer's certification programo
4.1.7 RECORDS
The written practice shall include the designation of the individual(s) or organization(s) responsible for maintaining
the qualification and certification records and where such records shall be kept.
4.2 METHODS
For the common methods listed in 1.3.1, the minimum requirements for training, experience and examination are
detailed in Sections 6 and 7. These requirements shall serve as a guideline for other current or emerging methods
as defined in 1.3.2.
4.3 RESPONSIBILITY
4.3.1 GENERAL
The employer is responsible for the implementation of, and compliance with, this standard and for certifying
qualified personnel. In addition, the prime contractor shall be responsible for compliance to this standard by their
sub-contractors. Employers using outside agencies shall be responsible for assuring that the appropriate
requirements of this standard are meto The employer is solely responsible for the certification of its employees and
cannot certify for another employer. Individuais cannot qualify themselves. Self-employed individuais may certify
themselves provided they have a written practice and have been qualified to the requirements of this standard by
another individual certified to Levei 3 in accordance with this standard.
4.3.2 RESPONSIBLELEVEL 3
The employer shall identify in writing a "Responsible Levei 3" to act on its behalf in matters regarding the NDT
qualification and certification processoThe Responsible Levei 3 shall be certified in accordance with this standard as
a Levei 3 in one or more NDT methods and shall have a thorough knowledge of the written instructions, codes,
specifications and standards used by the employer. He/she shall also have a thorough knowledge of the materiais,
components, product technologies, NDT methods and NDT techniques used by the employer. Additional Examiners
as defined in this standard may be identified and delegated in writing as necessary to provide coverage for ali
methods used by the employer. The Responsible Levei 3 may be an outside agency but in this case he/she can only
qualify personnel, as only the employer can certify personnel. The Responsible Levei 3 shall be responsible for
implementation of this standard and the overall administration of the qualification and certification programo
REVISION
5
NAS410
SHEET 12
CopyrtqhtAerospace Industries~IicQlfoPilf ~b!W~g. UPON THIS DOCUMENTOR ANYNATIONALAEROSPACEST,~lfQnlii,~I\Ir.IBii~Y8VOLUNTARY. AIA DOES NOT QUALlFYSUPPLIERS OR CERTlFY
Providedby 'HS Marki'under 'i~Nü OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD:,;;0"'JlêJIt'II!:ti!i:N1il>rWi'RI:!tIfiS!lN]iIitIÁl[llt0Iil;'~1~ffldEt!!JIléIil(BI{Y OF
No reoroducucnor networkingP4'T4!!I+!l fI~N'\!rjl"'I!f«lJIlAR APPLlCATION OR (2) THE EXISTENCEOF OR APPLl(JIJ!Ilt!I'N~01Elfl PÃ~N'ltUR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. All RIGHTS RESERVED NATIONAL AEROSPACE STANDAROS
An employer may use a Levei 3 certified in accordance with this standard from an outside agency to develop a
certification program, act as the Responsible Levei 3, examine NDT personnel or perform any other qualification or
Levei 3 function. An outside agency may qualify, but not certify personnel. The employer shall document the
suitability of any outside agency selected to perform any function in meeting the requirements of this standard.
This documentation shall be of sufficient detail to justify the outside agency's ability to perform the required Levei 3
fu nction( s).
5.1.1 GENERAL
The four basic levels of certification are Levei 1-Limited, Levei 1, Levei 2 and Levei 3. The employer may subdivide,
add or limit levels as appropriate, but cannot eliminate or reduce the minimum requirements for each leveI. If the
employer does not wish to use ali of the levels, those levels to be used shall be documented in the employer's
written practice. Where other variations or subdivisions are implemented, the requirements and responsibilities
shall also be detailed in the employer's written practice.
NDT personnel shall not independently perform the functions listed in 5.1.3, 5.1.4, 5.1.5 and 5.1.6 if not certified to
the appropriate levei in the applicable techniquejmethod.
5. f:2 TRAINEE
An individual who is documented as participating in a training program for an NDT method and is in the process of
becoming qualified for certification to Levei 1-Limited, Levei 1 or directly to Levei 2 shall be considered a trainee. In
the techniquejmethod in which they are preparing for certification, trainees shall:
• Be documented as a trainee and be actively participating in a training program for a stated NDT method for a
limited and specified period of time.
• Obtain experience under the direct observation of a Levei 2 ar Levei 3 in the same method.
• Obtain experience under the direct observation of a Levei 1 or instructor only when approved by the
responsible Levei 3.
• Not make accept or reject decisions.
• Not independently conduct tests.
• Not independently perform any other NDT function.
5.1.4
REVISION
5
NAS410
SHEET 13
CooyriçbtAercepace Iodustríes,l.§ScQ!foP& JijibWl,;;g. UPON THIS DOCUMENTOR ANYNATIONALAEROSPACEST,~I/J;)"'~F.~~Y6VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Prcvíoeoby 'HS Ma"';' under Hc~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD:>Soé&AJI1III:fi!l:;NJj)rW:Rl!t8littfó\it!Á)[lI,eIil;(_~~l1ldE1i1JIlélil(wn OF
No reproductionor netwock;ngP<I1T'IiMlI f'0R46.N:l!cJilAR'ffOOIlAR
APPLICATIONOR (2) THE EXISTENCEOF OR APPLI()UJlY1V>~010Jl1'A'IllmtUR. TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAL AEROSPACE STANOARDS
• When specified in the written practice and approved by the Responsible Levei 3, may perform interpretations
and evaluations of specific product(s) or product formes) for acceptance or rejection in accordance with
approved work instructions.
u
5.1.5
~
5
c;e In the method in which certified, Levei 2 individuais shall:
w
:>:
«
u,
O • Have the skills and knowledge to set up and standardize equipment, process parts, interpret and evaluate for
Z
O acceptance or rejection, and document results;
§ • Be thoroughly familiar with the scope and limitations of the technlque/rnethod:
u
O
Vl • Have the skills and knowledge to conduct system performance checks in accordance with the applicable
~
Vl
process standard;
~ ~ • Se capable of providing the necessary guidance and/or supervision to trainees and Levei 1 personnel;
~ci~
::»'" • Se familiar with the codes, standards, and other contractual documents that control the method as used by the
offi«
~z> employer;
UJ O z"
~~§ • When specified in the written practice, be capable of developing work instructions from approved general
Bl:=z procedures. Such work instructions shall require final approval by a Levei 3 certified in the method;
ffi8~
«~« • Have a basic knowledge of relevant product manufacturing and inspection technology;
• When specified in the written practice, have a basic knowledge of aircraft or vehicle maintenance.
5.1.6
• Have the skills and knowledge to interpret codes, standards, and other contractual documents that control the
NDT method(s);
• Se capable of assuming technical responsibility for the NDT facility and staff;
• Se capable of selecting the method and technique for a specific test;
• Se capable of preparing and verifying the adequacy of procedures and work instructions;
• Approve NDT procedures and work instructions for technical adequacy;
• Have a general knowledge of other NDT methods and product manufacturing and test technologies used by the
employer;
• When specified in the written practice, have a basic knowledge of aircraft or vehicle maintenance;
• Se capable of providing or directing training, examination, and certification of personnel;
• Conduct NDT for the acceptance of parts and document the results if a demonstration of proficiency in this
ability was included in the practical examination;
• When required by the written practice, be capable of auditing outside agencies to ensure the requirements of
the written practice are met.
5.1.7 AUDITOR
Personnel performing technical NDT audits, surveys or assessments shall have the training, skills and knowledge to
understand the processes and procedures utilized in the application of NDT processes. The individual shall be
familiar with the applicable codes, standards, and other contractual documents that control the applicable
method(s).
6.1 TRAINING
6.1.1 GENERAL
Candidates for certification to ali levels shall complete sufficient formal training to become proficient with the
principies and practices of the applicable test method and technique(s) and be capable of carrying out the duties
REVISION
5
NAS410
SHEET 14
Copy'igh!Aemspace InduSlries)Jâscl;lliohl& Jiji6Wlr;;~. UPON THIS DOCUMEI'ITOR ANYNATIONALAEROSPACEST,~llJ;lnl6\,~I\IJ;I!lIi9Y8VOLUNTARY. AIA DOES NOT QUALlFYSUPPLIERS OR CERTIFY
Providedby IHSMa"';!unde";~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~"'oilliA~lifRli!f8tiN]tMUl[ll~it(laWd1~ffIdE~élilBI{Y OF
No reproductionor nefworkinq _ f'OA4O.lII'l!cJOAmcJtj~RAPPLlCATION OR (2) THE EXISTENCEOF OR APPLlO\IiJ_~OlOl'1 M'IllNNlR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRIGHT 2020 AEROSPAeE INDUSTRIES ASSOeIATION Of AMERIeA, INe. ALL RIGHTS RESERVED NATIONAl AEROSPACE STANOAROS
specified in Section 5. Formal training shall be conducted prior to, or in conjunction with, on-the-job training. Ali
completed NOT training shall be documented.
The minimum training hours for Levei 1 and Levei 2 are provided in Table I and Table IA for the specified NOT
methods. Individuais cannot certify to Levei 3 without prior certification to Levei 2 in the method. Military
equivalency of training and experience can be determined by the Responsible Levei 3 or Examiner in accordance
with sections 6.1.4 and 6.3.3 for certification to Levei 3.
40 additional hours of training is required for current certified Levei 3 radiography personnel transitioning to either
film or non-film radiography.
General, specific and practical training may be obtained with the employer or outside agency but shall always be
supplemented by practical on-the-job training with the employer.
Ali training shall be conducted in accordance with a detailed outline approved by the Responsible Levei 3 or
Examiner. The outline shall include a list of references from which the training material ís derived. As a minimum
the training shall include:
·• Basic theory;
Test principies, including choice of NOT methods, relevance to different materiais and part and test variables;
• Product forms and materiais; defect formation and characterization;
• Equipment operation and standardization;
• The importance of process controls;
• The importance of appropriate processing steps and parameters;
·
•
Safety regulations;
Applicable techniques and the advantages and disadvantages of each;
• Limitations and capabilities of each method and technique;
• Applicable specifications, codes, operating procedures and work instructions;
• If applicable, evaluation, interpretation and documentation of test results.
REVISION
5
NAS410
SHEET 15
Copyriqht Indusntea )JI,jlicQ/fohllit Jij;bWl';;~. UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE ST,~llJJnI§'~~9Y8VOLUNTARY.
Aerospace AIA DOES NOT QUALlFY SUPPLIERS OR CERTIFY
Prcvided by IHS Markituodertlc~N.ü: OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD:"0"'Jo&Irt1II3'i!i;N0JtiERI!f6fittf~[II!0it'1D\llM,~ffkIE~lIil1en:v OF
No reproovcton or oelworl<'og_ t>IJIiI4A.N'I'rjilArnaJIiAR APPLlCATION OR (2) THE EXISTENCE OF OR APPLlO\8ItOV>_O'EJIl JYI\'IllN11-lJR TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAl AEROSPACE STANOAROS
If an outside agency is used to provide training, the Responsible Levei 3 shall verify that the training meets the
employer's requirements.
6.1.3 PREVIOUSTRAINING
u
~ For personnel credited with previous training, or personnel not certified within 12 months of their training, refresher
<5 training must be provided. Previous training must be documented to be accepted by the employer. As a minimum,
~
..~
::E refresher training shall cover products, equipment set-up, operation and standardization, specific operating
procedures, applicable techniques, interpretation and evaluation of NDT results, safety, and applicable codes,
Z
o standards and specifications. For documentation of previous training, records other than original records may be
§ accepted if adequacy and equivalency have been determined to be acceptable by the Responsible Levei 3 or
u
o
Vl Examiner.
~
Vl
~ ~ 6.1.4 EOUIVALENTTRAINING
~ci~
::o>N
~~~ For personnel previously certified under NAS410, EN 4179 or other recognized NDT qualification programs, the
wOz
~:;J~ adequacy and equivalency of their previous training to the requirements of Table I and Table IA shall be determined
Vl;l:Z
and documented by the Responsible Levei 3 or Examiner. Ali or a portion of previous hours may be accepted as
.. ~..
ffi8~ applicable .
Ali regulations relating to hazardous substances, accident prevention and safe working practices shall be strictly
adhered to. Safety-related training requirements shall be determined in accordance with local codes and
regulations. Prior to certification, ali candidates seeking radiography qualification shall have received instruction on
the hazards and safety requirements associated with ionizing radiation and be knowledgeable of, and comply with,
the applicable regulations and laws.
6.2.1 RESPONSIBLELEVEL 3
The Responsible Levei 3 shall maintain overall control and cognizance over the NDT training program, including
designating or approving qualified Examiners, instructors and outside agencies.
6.2.2 EXAMINERS
When necessary, Examiners shall be designated or approved in writing by the Responsible Levei 3. Ali Examiners
shall be certified in accordance with this standard. As determined and documented by the Responsible Levei 3, an
Examiner can prepare, administer and grade written or practical NDT examinations, and administer ali or part of,
the qualification process in the method in which hejshe is certified.
6.2.3 INSTRUCfORS
Instructors shall have the skills and knowledge to plan, organize, and present classroom training and practical
exercises in accordance with approved training outlines. Instructors shall be designated or approved by the
Responsible Levei 3 or Examiner.
When an outside agency is used, the outside agency shall provide the employer with the names, evidence of
qualifications and, if applicable, evidence of certifications held by the personnel conducting the training and
examination.
REVISION
5
NAS410
SHEET 16
Copy,ighlAercepace lndustnes~hlIfohlil< R.\i~~r;;g.UPON THIS DOCUMENTOR ANYNATIONALAEROSPACEST,~I/Qn!~~~~Y8YOLUNTARY. AIA DOES NOT QUALlFYSUPPLIERS OR CERTIFY
Provtoedby IHSMa"it under Ii~ OF lTEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD:"o"'IIê:M1It:ti!CN0Iif~t\ifW[lI,oI6'_~ffIdE~êIiIllIn' OF
No recroducucno, netwo,king_ flllf'l"'N!I!'1>AmaJQAR APPLlCATION OR (2) THE EXISTENCEOF OR APPLlClIIJ__ O'Elfl ""'~N1't1JRTRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATiONAL AEROSPACf SlANOARDS
6.3 EXPERIENCE
6.3.1 GENERAL
Candidates for certification to Levei 1-Limited, Levei 1, Levei 2 or Levei 3 shall have sufficient practical experience to
assure that they are capable of performing the duties of the levei for which certification is sought. The minimum
experience requirements for Levei 1 and Levei 2 are provided in Table II and Table lIA, as applicable. The
requirements for Levei 3 are in Table III and 6.4.3, as applicable. As documented in the written practice, on-the-job
training for the purpose of gaining experience shall be overseen by personnel certified in accordance with this
standard. For trainees gaining experience, documentation shall be available for review to indicate individual, date,
description of activity within the method, hours, and certified personnel providing direct observation.
Additional experience requirements for current Levei 3 radiography personnel transitioning to either film or non-film
radiography are 240 hours with guidance or supervision from an examiner, instructor, or outside agency.
6.3.2 PREVIOUSEXPERIENCE
A candidate's experience with a previous employer may be accepted by the current employer only if such
experience is documented and approved by the Responsible Levei 3 or Examiner. Ali or a portion of previous hours
may be accepted as applicable. For documentation of previous experience, records other than original records may
be accepted if adequacy and equivalency have been determined to be acceptable by the Responsible Levei 3 or
Examiner.
For personnel previously certified under NAS410, EN 4179 or other recognized NDT qualification program, the
adequacy and equivalency of their previous experience to the requirements of Table lI, Table lIA, or Table III shall
be determined and documented by the Responsible Levei 3 or Examiner.
REVISION
5
NAS410
SHEET 17
Copynqht Aerospace Inoustnes).!!,iScQjfoP&Jijib!W~g. UPON THIS DOCUMENTOR ANY NATIONALAEROSPACEST,~l/Qnl6\,F.rw:.l.!!li9Y8VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Provided by IHS Markit under Iic~N.ü OF illMS PRODUCED UNDER NATIONALAEROSPACESTANDARD:>Sotl'tIo&M1\II:fi8:N0r1jlfAl!tSfi!tfilit!A)[lI!OIill'_~~ffIdE~êIiI(llID' OF
No reproduction o, networkinq pE!llil!M9 flOR4f\NYoJO""tffOtlêARAPPLICATION OR (2) THE EXISTENCEOF OR APPLI(}\I1l_~{l10J1 PA'IllI'I'NJR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATlON OF AMERICA, INC. ALL RIGHTS RESERVED
~
NATIONAL AEROSPACê S'fANOAROS
The minimum required training and experience hours for methods used by the employer that are not listed in 1.3.1,
Table I, and Table II shall be established by the Responsible Levei 3.
When determining training or experience hours for new methods not listed in Tables I and II, the minimum hours
shall be based on the requirements for a method of similar complexity listed in Table I and II. This only applies to
"other" or emerging methods as defined in 1.3.2 and cannot be applied to penetrant, magnetic particle, ultrasonic,
radiography, thermography, or eddy current testing.
6.4.3 LEVEL3
When approved by the cognizant engineering organization and authorized by the employer's written practice, an
employer may qualify and certify its first Levei 3 in a new NDT method not listed in 1.3.1 provided:
• The candidate has the skill and ability to carry out the Levei 3 responsibilities in 5.1.6;
• Ali of the requirements in Table IV are met.
The requirements of 6.4.1,6.4.2 and 6.4.3 only apply to "other" or emerging methods as defined in 1.3.2 and
cannot be applied to penetrant, magnetic particle, ultrasonic, radiography, thermography, or eddy current testing.
REVISION
5
NAS410
SHEET 18
Ccpyriqht Aerospace tndustrles .A.§!idJ!'oPIlr ~blA\Jr;;~. UPON THIS DOCUMENTOR ANY NATIONALAEROSPACESTi\MQ!ll/QrJl?e~rw3!ljj~Y8VOLUNTARY.AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Provided by IHS Markll under tlc~Nü OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD;"'0"'iIA~N0JrIilERl!fSfit{fMWIiI<flIi6'iD\liM1~~lfIdEtIDliI'éliiBN:Y OF
No reprooucuonor nelworklng p_ f'_NVrjOA~tJI?AR APPLICATION OR (2) THE EXISTENCEOF OR APPLICI\8__ 0'El1d M'IliN'NJR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRIGHT 2020 AEROSPAeE INDUSTRIES ASSOeIATION OF AMERIeA, INe. All RIGHTS RESERVED
il1m
NATIONAL AEROSPACE STANDAROS
7. EXAMINATIONS
7.1 PURPOSE
7.1.1 GENERAL
t3
õ1 Examinations to verify the technical qualifications of candidates shall consist of a general, specific and practical
UJ
:;: examination for each method in which the candidate is to be certified. Specific examinations shall be administered
<
u,
o after a minimum of 75% of Table II requirements have been completed. Table II requirements shall be complete
z
o prior to administration of practical examination. An examination for visual acuity shall also be conducted prior to the
§ candidate's first certification and periodically thereafter. The requirements for the vision examination, the questions
u
&l or question data base used for the general and specific examinations and the checklist for the practical examination
~ shall be available for review by the employer's customers. Examinations and test samples shall be made available to
the candidates only during administration of the examinations. Verbal translation of written examinations is not
permitted.
The vision examination for ali levels shall assure that the applicant's near vision and color perception meet the
requirements of Table V. Vision requirements do not apply to instructors or auditors. Near vision tests shall be
administered annually and color perception tests shall be administered at least every 5 years. The employer shall
ensure the flow-down of the Table V vision requirements to ali necessary personnel and/or facilities. Snellen and
Jaeger tests shall be administered by trained personnel designated by the Responsible Levei 3 or by qualified
medical personnel. When vision correction is necessary to pass the visual acuity exam, vision correction shall be
worn during ali testing/inspections. Any limitations in color perception shall be evaluated by the Responsible Levei 3
prior to certification and must be approved in writing.
7.1.3 GENERALEXAMINATION
The general examination shall be a closed book examination covering the cross-section of the applicable method at
the appropriate leveI. A minimum of 40 questions shall be administered for the general examination at Levels 1, 2
or 3. For Levei 3, the general examination questions shall address the general knowledge of other methods used by
the employer at the initial certification as well as the method for which certification is sought. Passing a "basic"
examination covering the other NDT methods used before passing any NDT method examination shall be
considered satisfactory evidence the other NDT methods have been satisfactorily covered. Possession of a current
ASNT, ISO 9712, or NANDTB certificate at the appropriate levei by the candidate may be satisfactory evidence that
the general examination requirement is satisfied as defined in the employer's written practice.
7. SPECIFIC EXAMINATION
The specific examination shall be an open book examination covering the requirements and use of the
specifications, codes, standards, equipment, operating procedures, product knowledge, and test techniques the
candidate may use in the performance of his/her duties with the employer. A minimum of 30 questions shall be
administered for the specific examination at Levels 1, 2, and 3. Reference material, as determined by the
Responsible Levei 3 or Examiner, such as specifications, tables, formulas, etc. shall be provided. Questions utilizing
REVISION
5
NAS410
SHEET 19
such material shall require understanding of the information contained therein rather than merely finding its
location.
7.1.5 PRACTICALEXAMINATION
The practical examination shall consist of a demonstration of proficiency in performing tasks that are typical of
those to be accomplished in the performance of the candidate's duties. If the candidate is required to demonstrate
proficiency in the application of the process as well as interpretation of results, hardware test samples shall be used.
The candidate shall not be familiar with the test samples and the location of the discontinuities located therein. If
the candidate is only required to interpret the results and not perform the process of generating the image, the test
samples may be images, such as radiographs or other resultant test data. A written checklist covering the topics
detailed in the following sub-paragraphs shall be developed and completed by the Responsible Levei 3 or Examiner
to assure adequate coverage and to assist in the administration and grading of the examination. In addition to using
the checklist, the Responsible Levei 3 or Examiner shall determine and document how the examination results
obtained by the candidate are to be documented (e.g. part maps, drawings, sketches, written descriptions, etc.). Ali
such documentation shall become part of the examination and filed accordingly.
LEVEL l-LIMITED
7.1.5.2
The candidate shall demonstrate proficiency by using a work instruction to process at least 2 test samples of
differing configurations for each method, with at least one test sample for each technique for which certification is
sought. When only one configuration of hardware is to be inspected upon certification, both test samples may be of
the same configuration. The test samples shall meet the definition in 3.37 and shall be representative of the
products to be encountered by the candidate in the performance of his/her duties with the employer. If approval to
accept or reject hardware is to be granted by the Responsible Levei 3, the candidate shall interpret and document
the results of the inspection of the test samples. The checklist shall include proficiency in the use and
standardization of equipment and materiais, adherence to procedural details and, if applicable proficiency in the
interpretation and evaluation of indications.
7.1.5.3
The candidate shall demonstrate proficiency by inspecting at least 2 test samples of differing configurations for each
method, with at least one test sample for each technique for which certification is sought. When only one
configuration is to be inspected upon certification, both test samples may be of the same configuration. The test
samples shall meet the definition in 3.37 and shall be representative of the products to be encountered by the
candidate in the performance of hís/her duties with the employer. In addition to the two minimum known and
documented test samples with discontinuities, specimens without discontinuities may be included. The candidate
shall document the NDT results in accordance with the applicable acceptance criteria. The checklist shall include
proficiency in the use and standardization of equipment and materiais, adherence to procedural details, the
accuracy and completeness of interpretation and evaluation of indications.
7.1.5.4
The candidate shall demonstrate proficiency by preparing an NDT procedure or work instruction appropriate to the
employer's current requirements for the method. The procedure or work instruction shall be developed in
conjunction with the general and/or specific examination(s) required for certification or recertification, as applicable.
The results of the practical examination shall be documented, and a checklist shall be used to address the technical
accuracy, technical content, and clarity of the procedures or written instructions prepared by the candidate. When
the candidate's duties will include processing and/or acceptance or rejection of products, proficiency in performing
such tasks shall be demonstrated by a hands-on practical examination equivalent to Levei 2 in accordance with
7.1.5.3.
REVISION
~
o 5
~
NAS410
SHEET 20
Copy,ighl Aercepace Induslries ~ScQjfoQ!ir Jiji~WI~~. UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE ST,~lMlnl~~~~Y8VOlUNTARY. AIA DOES NOT QUAllFY SUPPLIERS OR CERTlFY
Provided by IHS Markitunder Ii~ OF lTEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARD:"'0"'JlêJrt'll!:fj!l:N0J~Rl!iSliNftMW[i,ea;(toW!I1~ffldEtilJJléStl6I{Y OF
No reproductlon o, netwo'king ~ f'OR<AIiI'I''fAAmOOêAR APPllCATION OR (2) THE EXISTENCE OF OR APPllO\S __ <l'EJld PA'Il:1IINJ1l. TRADEMARKS RIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRlGHT 2020 AEROSPACE INDUSTRlES ASSOCIATION OF AMERlCA, INC. ALL RlGHTS RESERVE O NATIONAL AEROSPACE SlANOAROS
7.2.1 GENERAL
The administration and grading of ali examinations shall be the responsibility of the Responsible Levei 3 or
Examiner. The Responsible Levei 3 or Examiner may delegate in writing the administration and grading of
examinations using multiple choice or true/talse type questions to non-Examiner personnel. Ali practical
examinations shall be administered by the Responsible Levei 3 or Examiner. Responses to essay and fill-in questions
must be evaluated by the Responsible Levei 3 or Examiner to verify the candidate's adequate understanding of the
subject matter. In no case can an examination be administered by one's self or by a subordinate.
When an outside agency is used to administer examinations, the employer shall ensure that ali individuais involved
in the administration of the examinations meet the requirements of this standard. In ali cases, the ultimate
responsibility for compliance to this standard shall remain with the employer.
7.2.3 SCORING
The candidate for certification must achieve a minimum score of 70% on each individual examination. In addition,
the candidate must detect ali discontinuities, flaws or conditions specified by the Levei 3 during the practical
examination and achieve a minimum score of 70%. The candidate must have an average score of no less than
80% in order to be eligible for certification. Ali examination scores shall be of equal weight in determining the
average score. For example, if only specific and practical examinations are administered for recertification, only
those scores shall be factored into the average score. If a general examination is also given for recertification, the
general score shall also be factored into the average score. For a Levei 3 recertified using Annex A, the score for the
hands-on practical, if administered, will be used as the average score. Scores for ASNT, NANDTB, or ISO 9712 NDT
certificates scored as "passjfail" and used in lieu of the general examination per 7.1.3 shall be assigned a value of
80%.
7.2.4 RE-EXAMINATION
Candidates failing any general, specific or practical examination shall receive additional training as determined and
documented by the Responsible Levei 3 or Examiner before attempting re-examination of the failed exam. The
additional training shall be documented and shall address those areas found deficient in the candidate's skills or
knowledge. The re-examination shall not use the same written tests or test samples that were used in the failed
examination. The re-examination test must contain a minimum of 25% new questions. A current certification shall
be suspended if an individual fails an examination for recertification.
8. CERTIFICATION
8.1 GENERAL
Personnel who have demonstrated that they possess the appropriate qualifications are eligible for certification by
their employer in accordance with the employer's written practice. Certification is not required for trainees,
instructors, NDT auditors, or personnel performing specialized inspections using direct readout instruments.
8.2 RECORDS
The employer shall maintain personnel certification records as long as the certification is in effect. The records
maintained by the employer shall include, as a minimum:
REVISION
5
NAS410
SHEET 21
copyrlqht Aerospace Indusfries~6dJli'ohl& ~b/;MJ!;;~. UPON THIS DOCUMENTOR ANYNATIONALAEROSPACEST,~~nI~~Il.I.F.!1lii~Y8VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Prcvidedby IHS M"kI' under "c~N.ü OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~"ot!JIt&~Nli)rilfRi!liSfiW'i!\iHA)IlI!Oi6(_,~ffldEtilJJa:éSiBItY OF
No reproductionor networklng_ fO_N-YrJilllmotJêAR APPUCATION OR (2) THE EXISTENCEOF OR APPLIOm __ <l'OJl PA'IllN'!t1JR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAL AEROSPACE STANDAROS
~
Ul
h. Results of the most-recent (i.e. current) visual acuity and color perception examinations;
i. Extent and documentation of formal education when used to meet qualification requirements;
'"
2
~
=>
~ j. The name and signature of the employer's representative authorizing the certification;
o k. Results of most recent annual proficiency review.
~ ;:;
w Z
U o
;t I:õ
Ul
z 8.2.2 RECORDAVAILABILITY
o
fl5
«
~
«
Ali training, qualification, and certification records shall be maintained in accordance with the employer's written
practice and shall be made available for audit. When an NANDTB is used, see Annex C. Ali such records, except for
actual examinations, shall be made available to the applicable employee upon request or upon leaving the company
for any reason.
8.3.1 EXPIRATION
Certifications shall expire when the certification interval has lapsed with no recertification issued. Certification,
annual proficiency review, and vision examinations are considered to expire at the end of the corresponding month
in which the event began.
8.3.2 SUSPENSION
8.3.3 REVOCATION
Certification shall be revoked when the individual does not perform in the certified method for the employer for at
least 24 consecutive months, when employment has been terminated, or when the individual's conduct is found to
be unethical or incompetent. When an individual is re-hired by the same employer within 24 months, certification
may be considered as suspended.
Certifications that have been suspended may be reinstated up to the original certification date when the cause for
the suspension has been corrected and the correction verified by the employer or the individual's proficiency is
verified by the Responsible Levei 3 or Examiner. Certifications that have expired or been revoked may only be
reinstated by specific and practical examination. Current NANOTB certificates may be utilized for new employment
provided that the new employer administers specific and practical examinations that are representative of their
processes and product per 7.1.4 and 7.1.5.
8.5 RECERTIFlCATION
Levei 1 and 2 personnel certified to this standard shall be recertified at intervals not to exceed five years.
Recertification shall be accomplished by successful completion of practical and specific examinations.
8.5.2
Levei 3 personnel certified to this standard shall be recertified at intervals not to exceed five years. Recertification
shall be accomplished ln accordance with Annex A or by successful completion of specific and practical
examinations.
If accepting products is required as a part of the duties of Levei 3, an additional hands-on practical examination
equivalent to Levei 2 is required.
The employer shall develop and implement a documented annual process to verify technical proficiency for each
method during the certification cyele for ali levels of personnel processing or inspecting products.
REVISION
5
NAS410
SHEET 23
CopydghlAerospace Industries ~Qf,or;>ilf R.\ib!W~~.UPON THIS DOCUMENT OR ANY NATIONALAEROSPACE ST,~lMlnlSi,~f\IT:mIl~Y8VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Provided by IHS Ma,'1t under "c~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACE STANDARD~"oé~~N0>rti'RI!t8tiN)o!iH.Q!1!Oi6'laWd1~TIldEt!1J.Iã:élii6l{Y OF
Noreproducnono, networkinq P<!lT'l!1I4!I
flllR46.N!1!'1OA~êAR APPLICATION OR (2) THE EXISTENCE OF OR APPLICl~IJ__ O'OJl PA'IllIII'NJR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRIGHT 2020 AEROSPAeE INDUSTRIES ASSOeIATION OF AMERIeA, INe. ALL RIGHTS RESERVED
;tm
NATIONAL AEROSPAC€ STANDAROS
A.1 SCOPE
This annex specifies the requirements for recertification of Levei 3 NDT personnel using the credit system. It applies only to
those persons holding a valld Levei 3 NDT certification at the time of recertification.
A.2 REQUIREMENTS
A.2.1 Documentation for recertification shall be submitted to the Responsible Levei 3 or NANDTB at least 14 days prior to
the expiration date of the certification. Application for recertification of the Responsible Levei 3 shall be made directly to the
applicable regulatory agency, NANDTB, or employer for review bya designated Levei 3.
A.2.2 The candidate shall have been employed in a Levei 3 function for a minimum of 36 months (at least 12 of which are
in the last 24 months) within the previous five years in the method(s) for which recertification is sought. The number of months
is cumulative and does not need to be consecutive months for validation purposes.
A.2.3 Continuity in the method shall be demonstrated. The candidate shall provide a list of 8 verifiable Levei 3 tasks in
each NDT method for which recertification is sought during the five-year period.
A.2.4 Candidates shall provide objective evidence that they have kept up to date with current NDT technology in the
method(s) for which they are seeking recertification by obtaining a minimum of 24 points during the five-year period of
certification, irrespective of the number of certifications (methods) obtained, by engaging in a combination of activities ílsted in
Table A.1.
A.2.5 The approval of Annex A activity documentation shall be determined and documented by the Responsible Levei 3 or
NANDTB as defined within the employer's written practice. Annex A recertification for the Responsible Levei 3 shall be
determined and documented by the employer. A single event shall only be used for one award credit activity during a five-year
period.
A.3 DEFINITIONS
A.3.1 COMMmEE OR PANEL MEmNGS: Meetings, conferences, symposia, seminars, trade association meetings, panels,
etc. organized or sponsored by a regional, national or international NDT organization or technical society. Foreign or
international meetings qualify if the sponsor(s) are national or international.
A.3.2 COMMmEE PROJECTS:Specific identifiable official activities of regional or national technical societies, committees
or work groups, such as round robins or individual studies, preparation of guidelines, appendices, specifications, recommended
practices, procedures, codes or standards, etc. Documentation may ínclude memos or reports, drafts of committee output
documents, or official written comments submitted by the candidate on such documents.
A.3.3 TASK: An activity for which Levei 3 certification is required, e.g. approval of an NDT Technique Instruction or NDT
procedure.
REVISION
5
NAS410
SHEET 24
CopyrighlAerospace Induslries~5cQlfor;>!It Jiji~~r;;g.UPON THIS DOCUMENTOR ANY NATIONALAEROSPACEST,~iMlnl~F.I\IH;!lIj~Y8VOLUNTARY. AIA DOES NOT QUALlFYSUPPLlERS OR CERTIFY
Providedby IHSMarkitunder lic~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD'''oi!ltA~NIil>Iti'Rl!t8fiNfili'tOO[l!t0a;'lDIllMl~~iIldEti1JI(féfi(WD' OF
No reproductionor nelworkingp<lJTll!M!ll'OfII46,iIf1!rJlA!ffrotJliAR
APPLlCATION OR (2) THE EXISTENCEOF OR APPL!(JIJ!IIYfté_01EJlil P'A'ItlN'I\.(JR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED N.ATIONAl AEROSPACE STANDAROS
REVISION
5
NAS410
SHEET 25
Copyriqht Aerospace Industdes )'§licQ#fohlllt Il,\;b/;w';;~,UPON THIS DOCUMEtiT" OR ANY NATIONAL AEROSPACE sr,~lIJ;lol6l.~~~Y6VOLUtiT"ARY, AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Províded by IHS Ma"'" under "c~ OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE srANDARD:"otl\lt&lrt'II:fi8:NJil"IilfRli!ÉSfiNfilitlÃ)[lI!0i13'iDWlt1~ffidE1itJIléIilBlD' OF
No reproducuon or networkinç _ "_l\I'I!rAAmotJtlAR APPLICATION OR (2) THE EXISTENCE OF OR APPLIO\9 __ 010Jl Wlffil'W1JR TRADEMARKS RIGHTS,
NATIONAL AEROSPACE STANDARD
© COPYRlGHT 2020 AEROSPACE INDUSTRlES ASSOCIATION OF AMERlCA, INC. ALL RlGHTS RESERVED NATIONAL AEROSPACE STANOAROS
B.l SCOPE
This annex specifies the requirements for qualification and certification of Levell-Limited NDT personnel in addition
to ali specified requirements within this standard. Annex B only applies when authorized by the cognizant
engineering organization and the employer's written practice.
REQUIREMENTS
When authorized by the cognizant engineering organization and the employer's written practice, the performance of
a specific NDT test on a specified part, feature, or assembly may be performed by personnel certified to Levei 1-
Limited. Each use of Levei l-Limited is a separate certification and shall be approved by the cognizant engineering
organization. An individual shall not possess more than three Levell-Limited certifications at any given time. The
following shall be documented and be made available for review by the employer's customers and regulatory
agencies:
Levell-Limited is a limited certification allowing only the performance of a specific NDT test on a specified part,
part feature, or assembly. In the test technique and method in which certified, Levei l-Limited personnel shall:
The minimum training hours for Levei l-Limited shall be determined and documented by the Responsible Levei 3,
but shall not be less than 25% of those required for Levei 1 in the applicable method.
Experience requirements for Levell-Limited shall be determined and documented by the Responsible Levei 3, but
shall not be less than 10% of those required for Levei 1 in the applicable method.
REVISION
5
NAS410
SHEET 26
Copy,;ghlAerospece lndustríes ~Qli'ohlllt ~b~~~. UPON THIS OOCUMENTOR ANY NATIONALAEROSPACEST,~I/J;!~~~ft,IJ:fflIi9Y8VOLUNTARY. AIA OOES NOT QUALlFYSUPPLIERS OR CERTlFY
Provroed by IHSMac'it under "c~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~>SotllltAo~N0tilfRl!f8tiN]ol\it!Ã)[lI<OIi\5'_~llldE~élilBI{Y OF
No reproducuon cr networ1<'ng~ "_N'I'<1OA~1lAR APPLlCATION OR (2) THE EXISTENCEOF OR APPLlCl\IIJ__ Q'Of/ I'l\'!l;N'lt{JR TRADEMARKSRIGHTS.
© COPYRIGHT 2020
NATIONAL AEROSPACE STANDARD
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED
;tm
NATIONAL AEROSPACE STANDARDS
B.2.5.1 Types of examinations: Examinations shall consist of a general, specific, practical, and visual acuity in accordance
with this standard. The following Annex B allowances for Levei 1-limited are provided:
B.2.5.2 General Examination: A minimum of 10 questions shall be administered for the general examination for Levei 1-
Limited.
B.2.5.3 Specific Examination: A minimum of 8 questions shall be administered for the specific examination for Levei 1-
Limited.
B.2.5.4 Practical Examination: The Levei 1-Limited candidate shall demonstrate proficiency by using a work instruction to
process at least one test sample for each technique and part configuration for which certification is sought. The
test sample(s) shall meet the definition in this standard and be representative of the specific product to be
encountered by the candidate in the performance of his/her duties with the employer. If approval to accept or
reject products is to be granted by the Responsible Levei 3, the candidate shall interpret and document the results
of the inspection of the test sample(s). The checklist shall include proficiency in the use and standardization of
equipment and materiais, adherence to procedural details and, if applicable proficiency in the interpretation and
evaluation of indications.
B.2.6 Records
For Levei 1-Limited certifications, the following records shall be maintained by the employer as long as the
certification is in effect:
B.2.7 Recertification
Levei 1-Limited personnel shall be recertified for each certification held at intervals not to exceed two years by
successful completion of practical and specific examinations.
REVISION
5
NAS410
SHEET 27
copyríçhtAerospace Indusldes~&:Qfohl!ltJt\i~~!;~. UPON THIS OOCUMENTOR ANY NATIONALAEROSPACEST,'~I!i\!WJ;jnll,\,~~~YBVOLUNTARY. AIA DOES NOT QUALlFYSUPPLIERS OR CERTIFY
Prcvided by IHS Ma,kllunoer IIc~ OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~"'oé~~N0ftRl!iSfiNft!\iHÃ)(lI!oil;(idltlM1~i1'IdE~êIi(en:v OF
No reprcdoctcn o, nelworl<lngP<I'TII!1I49
f'0A46.iII'!!<AAAAIIOtIIlAR
APPLlCATION OR (2) THE EXISTENCEOF OR APPLlCl~8MN>~01~ AA'Il1N'ftUR TRADEMARKSRIGHTS.
NATIONAL AEROSPACE STANDARD
© eOPYRIGHT 2020 AEROSPAeE IHDUSTRIES ASSOeIATIOH OF AMERIeA, rsc, ALL RIGHTS RESERVED
fi1m
NATIONAL AEROSPACf STANDAROS
C.1 SCOPE
This annex specifies the requirements for qualification of NDT personnel under the general control of a National
Aerospace Non-destructive Testing Board (NANDTB) in accordance with this standard.
C.2 REQUIREMENTS
C.2.1 A NANDTB is an independent national aerospace organization representing a nation's aerospace industry and is
recognized by the nation's Regulatory Agency to provide or support NDT qualification services in accordance with
this standard. Each NANDTB shall be recognized formally in writing by the nation's Regulatory Agencies.
C.2.2 Each NANDTB shall define, organize, administer and manage activities in accordance with this standard.
C.2.3 Each NANDTB shall have a written constitution, deciding entity and be governed according to administrative and
working procedures and shall issue a statute or similar document containing:
C.2.4 As a minimum, the voting members in the deciding entity shall be Levei 3 personnel from design, production and j
or maintenance organizations that are approved by the nation's regulatory agency. Other members may be co-
opted as voting or non-voting members as necessary to support the activities of the NANDTB.
C.2.5 Regulatory agencies for civilian and/or defense have the right to be included as observer members of the NANDTB.
C.2.6 Each NANDTB shall disclose on a public forum, e.g. on a web site:
C.2.7 Applicable NANDTB procedures shall be available for review j audit by the employer's customers and regulatory
agencies.
5
NAS410
SHEET 28
CopyrighlAerospace Induslries~lichllfo~!H !lIii~~h;~. UPON THIS OOCUMENTOR ANY NATIONALAEROSPACEST,~liIJnI~~hJTi!!Ij9Y8VOLUNTARY. AIA DOES NOT QUALIFYSUPPLIERS OR CERTIFY
Providedby IHSMarkltunder Iic~Nü' OF ITEMS PRODUCED UNDER NATIONALAEROSPACESTANDARD~"'oll'llt&~NliM~ff1i!f8tittfi\it!Al[ll~Ii6'_,~f!ldft>Un'éfi(1lI{Y OF
No reproductionor networkingp<!l1'l!ll4!l
f'OIli4/>.N'I'r1lArnGtJIlARAPPLICATION OR (2) THE EXISTENCEOF OR APPLIO\8 __ 0 G1l P'A'IllIII'ItUR.TRADEMARKSRIGHTS.
'
NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2020 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED NATIONAl AEROSPACE STANOARDS
If an NANDTB is used to provide training and/or examinations, it shall be treated as an outside agency and the
employer's Responsible Levei 3 shall verify that the training andjor examinations meet the employer's requirements.
Where an NANDTB is used, the specific and practical examinations may cover a wider scope that does not include
ali the employer's requirements. Where a wider scope is used by the NANDTB the employer is responsible for
administering supplemental specific and practical examinations which are representative of the employer's
processes. These supplemental examinations shall be under the control of an employer or NANDTB when required
by the National Aviation Authority.
C.2.11 For emerging NDT methods, where the applicable NANDTB has a process for qualifying the first Levei 3 in new NDT
method this process shall be used.
C.3 EXAMINATIONS
C.3.1 The control and administration of NDT exams at examination bodies shall be subject to audit either by an NANDTB
or by an organization (NDT society) which is overseen by the NANDTB. This audit shall be conducted by auditors
who comply with this standard and shall include:
• Review of quality documentation covering the examination of aerospace NDT personnel meeting the
requirements of the approval criteria;
o Examination bodies quality system documents and procedures;
• Availability of codes, standards and specifications as relevant, including if needed, the employer's written
practice;
• For externa I bodies, assurance that a contract review took place;
• Appointment of appropriately qualified and experienced examination staff;
• Confidentiality, impartiality and security;
• Compilation of written specific and practical examinations appropriate to scope (relevant to products, NDT
procedures and processes);
• Examination marking and grading in accordance with this standard.
C.3.2 Outside Agencies under the control of a NANDTB may be recognized by formal approval of NANDTBs and/or
organizations in other countries where the controlling NANDTB complies with the minimum requirements of this
standard and is a member of the Aerospace NDT Board Forum.
When an NANDTB is used, the scores for the latest written and practical examinations shall be kept by the employer
but actual examinations may be kept by the NANDTB. Ali such records, except for actual examinations, shall be
made available to the applicable employee upon request or upon leaving the company for any reason.:
••
REVISION
5
NAS410
SHEET 29
Ccpyrtqht Aeroepace lndustries Álâ5chllfohl!lf mi~~~Ii. UPON THIS DOCUMENT OR ANY NATIONALAEROSPACE ST,~lfJdnl6\,~Il;I);IAA~YBVOLUNTARY. AIA DOES NOT QUALlFYSUPPLIERS OR CERTIFY
Provtoeo by IHS Markit under Iic~Nü' OF lTEMS PRODUCED UNDER NATIONALAEROSPACE STANDARD~""0i!1tA~NJi)II<fARf6fittfMI.Q!lI~iM:1d\1IM1~itldE1iIJJ(I'éli!(8l{Y OF
No reoroductlon or networklnq P1'JltiM!! f'OfII4'.JlÇtojAAMrotJIiARAPPLlCATION OR (2) THE EXISTENCE OF OR APPLlO\S __ O'OJl PlI'Il!i\tI1.UR TRADEMARKSRIGHTS.