Professional Documents
Culture Documents
ENT Workstation
Model : New Millennium Grand _2014.02_Rev.6
Manufactured by
MEDSTAR Co., Ltd.
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
Homepage : http://www.medstar.co.kr
E - mail : president@medstar.co.kr, trade@medstar.co.kr
1. Brief..............................................................3
2. Specification.................................................4
3. Structural Lay-Out........................................5~16
4. Operation.....................................................16~28
5. Precaution in Use….....................................29~30
6. Maintenance & Storage................................31~37
7. Plumbing Drawing…………………………..…38
8. Trouble Shooting……………………….…...…39~42
9. Standard Accessories...................................43~44
10. Product Information Sticker..... ...................45
11. Warranty Certificate………………………….46
In addition, using the optional parts, such as endoscopic visual imaging system, film
view box, patient chair connected to New Millennium Grand, stool, as well as ear
irrigation system, automatic drainage system, ENT doctor can carry out their jobs in a
very efficient way
Dimension 1,652(W)x782(D)x800(H)mm
Weight 170Kg
18
19
31
20
21
15 12 13 14 16 17
2 3 4 5 6 7 8 9 10 11
Rectangular Wastes
11 Put the wastes after treatment.
Tray
Surgical Instrument Put a wide range of surgical instruments into the warm
12
Tray tray.
Lid for Surgical
13 Cover for the surgical instrument tray.
Instrument Tray
17 Straight Post Pole Arm for Film View Box, Another Monitor Arm, Fastened.
Endoscope Sterilizer
26 Turn on / off the power of the endoscope sterilizer.
Power Button
Suction Bottles Peep Take a look at how much level suction bottles are filled
29
Hole with wastes, secretions, etc.
Open / Close the door to take out / put the suction
30 Front Door
bottles on the sliding plate.
13
15 16
3 Air compressor Motor Forward air to the air tank, driven by Motor
4 Compressor Motor Socket Two Head Motor’s plugged into the socket for air compressor.
5 Main Suction Motor Socket Two Head Suction Motor’s plugged into the socket for main suction.
Single Head Suction Motor’s plugged into the socket for sub-
6 Sub Suction Motor Socket
suction.
Pressure Gauge, Regulator, Set the pressure of suction, spray & indicate its value onto the
14
Filter gauze, while filtering the impure particles of the air.
15 Relay PCB Relay the signal that each part operates.
Get the signal from the local control panel, others & control the
16 Main PCB
whole signals and give the signal to relay PCB.
supplied, which is used for eliminating the fog/mist, layered on the tip of endoscopes
in the winter season or in a much temperature gap place causing to make a mist in a
dew point.
1 Arm Set Fasten the film view box onto the straight post pole.
2 Button Pressing it, ENT anatomic chart lifts up, with rolling- up
hung.
Pulling down the bottom bar, ENT anatomic chart lifts
3 ENT Anatomic Chart
down.
Inserting the x-ray film into the top bar, ENT doctor can
4 X-Ray Slim View Box
read what it means.
5 Main Power Switch Turn on / off the main power.
7 Main Power Cable Supply the main power to the x-ray film view box.
4
8 9 10
5
3
2 13
1
M ic r o s c o p e
11
12
8) Be sure to place each pin into a corrective position, when connecting the CCD
The illumination light helps to enlighten the surroundings for ENT doctor to be able to
diagnose and treat patients, effectively and efficiently, while it’s moved in a versatile
T E N S IO N R E G U L A T IO N
L IG H T A R M
C O VE R
LAM P
L IG H T C O N N E C T O R
L IG H T H E A D
- Holding up the illumination light head part by the hand, slightly forcefully insert its
plug into the hole of the end of long swivel bar, until it appears at the rear bottom
2) Overall View
- This equipment consists of the two CCD camera socket, two light source sockets,
light intensity control knob, several one touch small switches, to be able to take
the photos by microscopic / endoscopic visual imaging system.
- The memory board inside can save the max. four photos, when taking the fifth
photo, the first photo
automatically deletes.
3-2) Touching the "Video A", it turns on, and if you retouch the"Video A", it turns on
"Video B", and if you retouch the "Video A", it turns on "Video C".
When you touch the "Video B", at the first / second / third time, it also turns on "
Video A" / "Video B" / "Video C" in a serial.
When you touch the "Video C", it appears the same result as the above.
"Video C" is the spare electrical video outlet / receptacle / socket, located at the
right bottom of rear panel in the LS-250, as I told you before.
3-3) If you touch the "Mode", you can select the division mode of display, such as
single / double / quadruple / continuous captured mode.
For instance, if you select the quadruple mode :
Focusing on the first object by endoscope and/or microscope, touch the " Capture"
and it's saved in the memory board of LS-250.
Thirdly, retouch the "Capture", and the previous photo is released, and taking a
focus on the third object and touch the "Capture", it's saved as the third photo.
Fourthly, retouch the "Capture", and the previous photo is released and finally
taking a focus on the fourth object and touch the "Capture", it's saved as the finally
fourth photo.
And then, if you touch the "Division" in a row, which should be corrected "Retrieval",
you can retrieve the first / second / third / fourth / finally all four photos.
4.Operation
4-1. Local Control Panel System
2 1 3 10
5 4 6 7
Ex.) PAL System, Double Mode => NTSC System, Double Mode, Live1
PAL System, Quad Mode => NTSC System, Quad Mode, Live1
NTSC System, Double Mode => NTSC System, Double Mode, Live1
NTSC System, QUAD Mode => NTSC System, Quad Mode, Live1
Ex.) PAL System, Double Mode => PAL System, Double Mode, Live1
PAL System, Quad Mode => PAL System, Quad Mode, Live1
NTSC System, Double Mode => PAL System, Double Mode, Live1
NTSC System, QUAD Mode => PAL System, Quad Mode, Live1
- Buzzer
① The buzzer sounds at the initialization of memory board.
② Pressing the any button, the buzzer sounds.
③ Without inputting the signal, even pressing any button, it doesn’t sound.
※ Common & Translucent Icon : Common icon means the frame capture, while the
translucent one indicates the field capture.
※Figure in Icon : means the speed of automatic capture which is shown on the table,
above..
- Menu
① Menu Entrance
Pressing the menu key for two seconds, the OSD, above appears with buzzer
sounded.
① X-POSITION
- Basic value is 50, can change from 40 to 60.
- Move screen to the left/right side.
② Y-POSITION
- Basic value is 50, can change from 46 to 54.
- Move screen up/down
③ OUTPUT SHARP
- Basic value is 20, can change from 0 to 100, at every 10 base.
- Control the sharpness of screen to the very minute level at the video-out socket.
④ 3DYC (3D Y/C Separation)
- Basic value is 50, can change from 0 to 100.
- Control the extent of 3D COMFILTER.
⑤ 3DNR (3D Noise Reduction)
- Basic value is 50, can change from 0 to 100.
- Control the extent of 3D Noise Reduction.
- The value appeared at the right end-side is the actual one, the noisier, the more
increased its value is.
⑥ AGC (AUTO GAIN CONTROL)
- Basic value is on, when off, input value becomes gain one.
- System Menu
① CAPTURE
- Set the saving way for the captured screen.
- AUTO : Sensing the movement of screen, in case the screen doesn’t move,
it ‘s captured as frame, vice versa, it’s captured as field.
- Frame : Screen captured as Frame.
- Field : Screen captured as Field.
- Pressing the button of image division for some seconds at the fixed display,
“Frame and Field” can be alternated.
② USB STORE (USB Only)
- AUTO : Capturing screens by foot switch, those are automatically saved in PC.
- MANUAL : Not automatically saving the captured images, it could be saved in a
specific way.
④ SPLIT-LINE
- Value of Change : BLACK, D-GRAY, W-GRAY ,WHITE , NONE.
- to split the screen.
- Basic Value : NONE
⑤ BUZZER-TIME
- Basic value is 50, can be changed from 0 to 100, at the increment of one(1)
- Adjust the length of Buzzer.
⑥ BUZZER-TONE
- Basic value is 50, can be changed from 0 to 100, at the increment of one(1)
- Adjust the volume of buzzer.
⑦ MODE-EDIT
- Basic Value : 1.ONE 2.DUAL 3.DDUA 4.QUAD 5.AVI
- Changeable Value : ONE, DUAL, DDUA, QUAD, PIP, MULT, AVI, NONE
- Setting this value in the menu key, mode can be changed.
⑧ EXIT
- Choosing exit, return to the previous status before system menu.
Nominal Volume
; 3,000cc
Net Volume
; 2,500cc
APPROX.100cc OF
CRESOL WATER
Warning ! : Be sure to clean out the suction bottle before it’s overflowing into the
4) Be sure to tightly close the lid / cover of the suction bottle to avoid any leakage of
air. In case air leaks, it could decrease the suction pressure, which can’t continue
PUSH SWITCH
CURVED.
STRAIGHT TIP
HOSE
BLUE.
BROWN BOTTLE
BOTTLE HOLDER
CAP
SPRAY HOSE
Warning ! : If the wastes might overflow into the suction motor from the sub-suction
bottle, the internal oil of the suction motor should be replaced, accordingly.
The wastes are filled into the main suction bottle at 2,500cc, secondly sub-
suction bottle at 1,000cc, and lastly overflows into the suction motor.
The wastes are discharged / leaked out from the filter of the suction motor.
3) If the terrible event, above should happen, it might hurt the suction motor,
seriously. In that case, first, open up the lid of the suction motor, secondly take
out water and lastly replace the oil, taking a look at the oil level gauge.
4) Be sure to regularly clean the filter to make sure that the suction motor keeps
in a good performance.
5) In case the suction motor caused by the overflow of the wastes breaks down,
don’t try to repair / maintain it, at your disposal.
6) Be sure to check the screw bottle at 250cc, since humidity / moisture generates
in the suction motor, and regularly empty it.
4 5 6
5 Air Line Flow the air, made by compressor, into the air tank.
3 4 5 6
8 7
11 9
10
Warning ! : - Be sure to completely empty the main suction bottle, on a daily basis.
- Be sure to completely empty the sub-suction bottle, if a scanty residue
remains, it might cause to emit the odor / make germs.
- Be sure to empty the screw bottle, at 250cc, which functions to collect the
condensed water from the motors.
If any secretion materials reversely flow into the screw bottle, it might cause
motors to be out of order.
- If it appears that the micro-switch doesn’t work properly, it should be replaced by the
new one.
11 Can, 50 ㎜ 2 1
15 Straight Spray 3 1
16 Curved Spray 1 1
18 Vent Hose 1 1
19 Vent Tip(#1~4) 1 1
20 Suction Hose 1 1
28 Remote Controller 1 1
Caution :
(1) It’s only designed for diagnosing and treating patients in the field of ENT.
(2) It’s only used under the given electrical power conditions, above.
(3) Don’t install the equipment at a slope of more than min. 5 degree on the ground,
otherwise, it might be fallen down / capsized on the ground.
(4) Be sure to always operate the equipment at the normal condition, if
it’s malfunctioned, stop its operation, immediately and contact the buyer / dealer
/ distributor in your country.
3. Others
• It didn’t work by force majeure.