Professional Documents
Culture Documents
ZSE
ISE
ZSP
PS
ISA
PSE
IS
ISG
ZSM
773
P0756-P0822-E.qxd 08.8.27 6:36 PM Page 774
Series ZSE1/ISE1
How to Order
Positive
pressure ISE1
Vacuum ZSE1
Output specifications
NPN open collector 1 output
14
w/o analog output, 3 turns adjustment
15
NPN open collector 1 output With Connector/How to Order
w/o analog output, 200 degrees adjustment
NPN open collector 2 output Without lead wire (Connector 1 pc., Socket 4 pcs.) ···ZS-20-A
16
w/o analog output, 3 turns adjustment
With lead wire······························································ZS-20-5A-
NPN open collector 2 output
17 Note) When ordering switch with
w/o analog output, 200 degrees adjustment
NPN open collector 1 output 5 m long lead wire, indicate Lead wire length
18 both part numbers.
w/analog output, 3 turns adjustment Nil 0.6 m
NPN open collector 1 output Ex.) ZSE1-01-15CN······1 pc.
19 30 3m
w/analog output, 200 degrees adjustment ZS-20-5A-50······1 pc.
50 5m
PNP open collector 1 output
55
w/o analog output, 200 degrees adjustment
774
P0756-P0822-E.qxd 08.8.27 6:36 PM Page 775
Analog output
1 to 5 VDC
Rated pressure range A B C
For vacuum 0 to –101 kPa 0 –101 kPa 10.1 kPa
5 For low pressure 0 to 100 kPa 0 100 kPa –10 kPa
Analog output (V)
1
0.6
C A B Pressure
775
P0756-P0822-E.qxd 08.8.27 6:36 PM Page 776
Series ZSE1/ISE1
Calibration Procedure Hysteresis Internal Circuit and Wiring Example
• Set the ON-pressure by the pressure setting Hysteresis is the pressure difference between the ON and
trimmer. Turning clockwise can set the high the OFF pressure of the output signal. The set pressure is I
Z SE1(L)- -14, -15
pressure/high vacuum pressure. the pressure selected to switch from OFF to ON condition.
•
pressure
In the event of setting, use a flat head
High vaccum
Brown DC (+)
High
trimmer, and rotate it lightly with a fingertip.
I Black OUT
Z SE1(L)- -14/-15/-18/-19 Set point ON
Hysteresis
LED Red
Connector
I Blue DC (–)
Z SE1(L)- 16/-17 DC polarity indicator
SET1
Indicator light SET2 2. Crimping of lead wires and sockets
Strip 3.2 to 3.7 mm at the end of the lead Caution
wires, insert the ends of the core wires
evenly into the sockets, and then crimp with Be sure to read before handling.
a crimping tool. When this is done, take care
that the coverings of the lead wires do not
Refer to front matters 58 and 59 for
enter the core wire crimping area. Safety Instructions and pages 687 to
(Crimping tool: model no. DXT170-75-1) 691 for Pressure Switch Precautions.
• Set the possible min. pressure for adsorption Core wire crimping area Covering retainer
confirmation. If setting the pressure lower Core wire
than that, switch becomes ON in case that Socket
Lead wire
adsorption is not completely done. If setting
the pressure higher than that, switch does
not become ON even though it may absorb Hook Covering
workpieces. 3. Attaching and detaching lead wires with
sockets
High vacuum
• Attaching
Insert the sockets into the square holes of
the connector (with +, 1, 2, – indication), and
Supply pressure continue to push the sockets all the way in
Steady adsorption until they lock by hooking into the seats in
Set point the connector. (When they are pushed in
Unsteady
their hooks open and they are locked
adsorption
automatically.) Then confirm that they are
Atmospheric Non adsorption locked by pulling lightly on the lead wires.
pressure 0
• Detaching
• Regarding the pressure setting To detach a socket from a connector, pull out
the lead wire while pressing the socket’s
Caution hook with a stick having a thin tip (about 1
Observe the following precautions for setting mm). If the socket will be used again, first
the vacuum pressure: spread the hook outward.
Use your fingertips to gently turn the Socket Connector
screwdriver.
Do not use a screwdriver with a large grip or
with a tip that does not fit into the trimmer Lead wire
Hook
groove because this could strip the groove.
776
P0756-P0822-E.qxd 08.8.27 6:36 PM Page 777
15
H HL L H HL
HYS SET HYS SET
Hysteresis setting trimmer Pressure setting trimmer Hysteresis setting trimmer Pressure setting trimmer
23 . 4 23 . 4
Indicator light (Red, Green) 23 Indicator light (Red, Green) 23
15
15
L HL H L HL H
SET1 SET2 SET1 SET2
Pressure setting trimmer 2 Pressure setting trimmer 1 Pressure setting trimmer 2 Pressure setting trimmer 1
600 (3000)
600 (3000)
ZSE
ISE
-
+21
ZSP
PS
40
40
72 . 3
79.8
Pressure supply Pressure supply
port ø2 port ø2
O-ring O-ring
ISA
9.5
9.5
30
30
PSE
21
21
6
27 27
2 x M2.5 x 24L Mounting threads 2 x M2.5 x 24L Mounting threads
IS
ISG
Grommet type: Connector type: ZSM
I 01 I 01
Z SE1- T1 -14/-15/-18/-19 Z SE1- T1 -14C/-15C/-18C/-19C
L H L H L H L H
15
I I
Z SE1-01-16/-17 Z SE1-01-16C/-17C
Pressure setting trimmer 1 Pressure setting trimmer 2
Pressure setting trimmer 1 Pressure setting trimmer 2
SET1 SET2
15
L H L H
SET1 SET2
L H L H
15
56.5
49
47
47
3.5
3.5
8.5
8.5
2 x ø3.5 Mounting hole 13 Piping port 01: R 1/8 2 x ø3.5 Mounting hole 13 Piping port 01: R 1/8
M5 x 0.8 depth 5 T1: NPTF 1/8 M5 x 0.8 depth 5 T1: NPTF 1/8
777