Professional Documents
Culture Documents
CO4: Obtain and analyze the response of electrical circuits using Laplace Transform for standard inputs.
1,
1 (a) 4 3 2.1.1
3
(iii)
a) 3 kW
b) 7 kW
c) 5 kW
d) 7 kW
In a three phase AC circuit, the sum of all three generated
voltages is ————
a) Infinite
(iv)
b) Zero
c) One
d) None of the above
3 identical impedances of 9<-30ᴼ Ω are connected in ∆ & 3 identical
impedances of 5<45ᴼ Ω are connected in star. Both the loads are
(b) 8 3 3 2.1.2
connected to the same supply system i.e. 3 phase 3 wire 480 V. Find
the line current & the total power supplied by the supply system.
The three, three phase Star connected balanced loads are connected to
a balanced 3 Phase, 3 wire system. Load A requires 21 KW at 0.8 p.f.
lagging, Load B requires 30KVA at 0.9 p.f. Leading and load C is a 3,
( c) 8 3 2.1.3
resistive load dissipating 12 KW. If the Line Voltage is 220 V, find 4
the currents on all the three loads separately & also the total line
current. Also calculate the Total Loading KVA on the supply mains.
Derive the relation between Line & Phase Voltage and Line & Phase 3,
(d) Current for a 3 Phase Balanced Star connected system. 8 3 2.1.3
4
Laplace transform changes the ____ domain function to
the _____ domain function.
a) time, time
(i)
b) time, frequency
c) frequency, time
d) frequency, frequency
In the bilateral Laplace transform, the lower limit is?
a) 0
(ii) b) 1
c) ∞
1,
2 (a) d) – ∞ 4 2 2.1.1
3
The unit step is not defined at t =?
a) 0
(iii) b) 1
c) 2
d) 3
Find the function f2 (t) from the time t = 1 to 3 sec.
a) (-10t+20) [u (t-1) +u (t-3)].
(iv) b) (-10t+20) [u (t-1) – u (t-3)].
c) (-10t-20) [u (t-1) + u (t-3)].
d) (-10t-20) [u (t-1) – u (t-3)].
The network of the figure reaches a steady state with the switch
K open. At t = 0, switch K is closed. Find i(t) for the numerical
values given and sketch the current waveform.
(b) 8 4 3 2.1.2
Fig. 2(b)
The accompanying figure is shown a network in which a steady
state is reached with switch K open. At t = 0, the switch is
2,
(c) closed. For the element values given 8 4 2.1.3
3
i. Determine the values of Va (0-) and Va(0+)
ii. Determine the values of Vb (0-) and Vb(0+)
Fig. 2(c)
In the network shown, the switch K is closed at t = 0 with the
network previously unenergised. For the element values shown
on the diagram:
i. Find i1(t)
ii. Find i2(t)
4,
(d) 8 4 2.1.2
5
Fig. 2(d)
Which among the following represents the precise
condition of reciprocity for transmission parameters?
a) AB-CD=1
(i)
b) AD-BC=1
c) AC-BD=1
d) None of the above
If the two ports are connected in cascade configuration,
then which arithmetic operation should be performed
between the individual transmission parameters in order to
determine overall transmission parameters?
(ii)
a) Addition
b) Subtraction
3 (a) c) Multiplication 4 5 1 2.1.1
d) Division
Which is the correct condition of symmetry observed in z-
parameters?
a) z11 = z22
(iii)
b) z11 = z12
c) z12 = z22
d) z12 = z21
Which elements act as an independent variables in Y-
parameters?
(iv) a) Current
b) Voltage
c) Both a and b
d) None of the above
Find the pole zero plot of the driving point impedance of the
Network shown.
(b) 8 5 6 2.2.1
Fig. 3(b)
For the given equation,
2𝑠 + 𝑠 + 13𝑠 + 6𝑠 + 56𝑠 + 25𝑠 + 25 = 0
4,
(c) (i) Check for the stability. 8 5 2.1.2
5
(ii) No. of Right hand, Left hand and imaginary roots
using 𝑅 − 𝐻 criteria.
(d) Explain Barlett’s Bisection Theorem. 8 5 3 2.1.1
CO- Course Outcomes
BL- Bloom's Taxonomy Levels
(L1 Remembering, L2 -Understanding. L3- Applying, L4- Analysis, L5- Evaluating, L6- Creating).