Professional Documents
Culture Documents
Componentry Rexnord 1
Componentry Rexnord 1
LF
R
WRB OPTI-Plus ® HP TM
®
Acetal Low Friction Wear resistant resin ® Special-Alloy Stainless Steel High Performance
Rex LF ® is a mixture of acetal based resins. To be used in abrasive environments (casting, In collaboration with the steel industry, Longer sliding wear life, reduced chain
Improves mechanical characteristics and machined steel components, sand, glass, Rexnord has developed a special heat treated elongation, lowest available friction. The
sugar). alloy of chrome steel with nickel. This results continuous search of Rexnord for
Chains
guarantees longer life in heavy duty
conditions (heavy products, long distances It offers a wear life 5 times longer than acetal in excellent strength properties, as well as improvement of their product has resulted in
and high operating speed). resin. improved corrosion-resistance. the development of a new, patentd, material:
Operating temperatures: The most outstanding properties of Rex-OPTI- Rex HP ™ High Performance.
The mechanical characteristics are similar to
in air ( - 40°C a + 80°C ) SALES OFFICES: Plus ® are its high resistance to wear, its This new material has the lowest coefficient of
those of acetal resin.
in hot water ( + 65°C ) ground finish, and 40% higher strength. friction, available on the market.
The chain is not suitable to be used in wet Austria - Wien
This material is especially suitable for
Inflammability: 94 HB. environments (can swell). Must use oil Denmark - Copenhagen In addition no "break in" is required thus
applications, where external lubrification is not
Colour: LF ( brown ), WLF ( white). lubricants. France - Paris-Lyon insuring maximum performance from startup.
possible.
Operating temperatures: Germany - Betzdorf (with distribution centre) Rex-OPTI-Plus ® is the preferred choice for
Operating temperature of Rex HP ™ material:
PRODUCT RANGE in air (- 5°C a + 100°C ) - Düsseldorf -Siegen-Stuttgart new or replacement installations.
in air ( - 40 to + 80 °C ) PRODUCT RANGE
Italy - Correggio (with distribution centre)
AS Inflammability: 94 HB. in hot water ( + 65 °C )
Netherlands - ‘s-Gravenzande (with distribution centre)
Colour: black. Colour: dark grey.
United Kingdom - Warrington
Conductive resin Canada - Edmonton-Montreal-Toronto-Vancouver
Load carrying capacity
United States - Atlanta (GA)-Columbus (OH)
Good electrical conductivity. - Dallas (TX)-Fresno (CA)-Grafton (WI) Longer sliding wear life *
Reduces the accumulation of electrostatic PC Mexico - Cordoba-Guadalajara
AISI 430 AISI 304 Rex-OPTI-Plus ®
Ultimate strength N
Lower mechanical characteristics.
Australia - Melbourne-Sydney
Flight wear
14000 Rex LF ®
Load carrying capacity is 40 % lower than Highly resistant to impact and to high Singapore - Singapore
Rex LF.® temperatures. 10000 Rex HP ™
China - Shangai
Lubrication system is recommended for Maintains its rigidity and other mechanical
7600
Chain elongation
( hinge wear )
WPP
elongation
Rex LF ®
% pitch
Rex
-OPTI-Plus ®
Reinforced polypropylene Rex HP ™
Coefficient of friction
Certification FDA & USDA 0,30
Rexnord Marbett S.p.A. RMCC Nederland 0,26
Italy P.O. Box 112
0,22
FDA USDA Via della Costituzione, 45 2690 AC ‘s-Gravenzande
0,18
42015 Correggio (RE) The Netherlands
American institute (Food and Drug United States Department of Agriculture, Tel. 0522 - 639333 Phone 0174 - 445111 0,14
Administration), responsible for the cerfification responsible for the approval of components and Fax 0522 - 637778 Fax 0174 - 445222 0,10
Metal Glass Plastic Paper
of materials to be in contact with food. machinery in the meat, poultry and dairy
E-mail vendite.italia@rexnordmarbett.it E-mail mcc@euronet.nl Product material
For direct contact with food the following industries.
materials have been approved: The following chains have been approved :
• AISI 304 843, 845, 963, 879, 879 TAB, 880, 880 TAB, * = dry
Graph shows comparative results at high-speed,
• HP,TM
WLF
R
882 TAB, 1843, 1873, 2873, 3873, 1700, 1701, operation.
1702. Bulletin No. 02063 November/2000 Printed in Italy
SALES OFFICES AND / OR DISTRIBUTION CENTRE
EUROPE NORTH AMERICA LATIN & SOUTH AMERICA ASIA & FAR EAST
AUSTRIA: Wien CANADA: Edmonton, Montreal, Headquarters: Miami (FL)-USA AUSTRALIA: Sydney
DENMARK: Copenhagen Toronto, Vancouver MEXICO: Cordoba, Guadalajara, SINGAPORE: Singapore
FRANCE: Paris, Lyon UNITED STATES: Atlanta (GA), Mexico City, Queretaro
GERMANY: Betzdorf, Columbus (OH), Dallas (TX), BRAZIL: Sao Leopoldo, Sao Paulo
Dusseldorf, Siegen, Stuttgart Fresno (CA), Grafton (WI)
GREAT BRITAIN: Warrington, (14 regional sales offices
ITALY: Correggio (RE) throughout the U.S.A.)
NETHERLANDS: AC 's-Gravenzande
® ®
®
OPTI-Plus ® HP ™ LF CurveMaster ™
Reproduction, even partial, of this catalogue is Rexnord is continually investigating methods of For further technical information please apply to
illegal. improving products and introducing new our Technical Dept.
technology, we reserve the right to modify data
and features shown in the catalogue.
Since 1936, when Rexnord had developed and introduced the first version of TableTop® conveyor chains, they have been
responsible for most of the advances in the technology of conveyor chains and associated products. Special chains have
been developed for conveying small pharmaceutical vials to heavy industrial parts.
The Rexnord TableTop® chains, today, are finding their way in all sorts of different industries, such as soft drinks, brewing,
dairy, packaging, parts handling, food processing and container handling. Rexnord has established partnerships with the
major original equipment manufacturers on a worldwide scale.
Rexnord products guarantee a worldwide service and availability. Products are being manufactured at different locations and
distributed via numerous distribution centres throughout the world. Further several teams of engineers, strategically located
are at our customer's disposal for application assistance.
GLOBAL
Betzdorf
(Germany) COMMITMENT Sao Leopoldo
(Brasil)
• State of the art equipment and technology
• Continuous quality improvement
• Widest range of products developed in close collaboration with leading original equipment manufacturers
• Continuous training of employees in all sectors
• High quality level
• Dedicated application engineering
• Use of FDA approved materials and development of products, certified by USDA
• ISO 9001 Certification
QUALITY IS A
REXNORD
COMMITMENT
WITH THESE ELEMENTS REXNORD HAS BECOME THE WORLDWIDE LEADER IN THE PRODUCTION AND
DEVELOPMENT OF PRODUCTS FOR THE CONVEYOR INDUSTRY
• State of the art equipment and technology
• Continuous quality improvement
• Widest range of products developed in close collaboration with leading original equipment manufacturers
• Continuous training of employees in all sectors
• High quality level
• Dedicated application engineering
• Use of FDA approved materials and development of products, certified by USDA
• ISO 9001 Certification
QUALITY IS A
REXNORD
COMMITMENT
WITH THESE ELEMENTS REXNORD HAS BECOME THE WORLDWIDE LEADER IN THE PRODUCTION AND
DEVELOPMENT OF PRODUCTS FOR THE CONVEYOR INDUSTRY
chains OPTI-Plus ® HP TM
19000 Acetal D
Ultimate strength N
Flight wear
14000 Rex LF ®
10000 Rex HP ™
7600
0 0 0,5 1 1,5
812- 815 802- 805 Millions of Ft. traveled
Chain type
elongation
Rex LF ®
% pitch
Rex
-OPTI-Plus ®
Rex HP ™
0,30
0,26
0,22
0,18
0,14
0,10
Metal Glass Plastic Paper
Product material
* = dry
Graph shows comparative results at high-speed,
operation.
4
chains
WRB
R
LF
Acetal Low Friction Wear resistant resin
Rex LF is a mixture of acetal based resins.
® To be used in abrasive environments (casting,
Improves mechanical characteristics and machined steel components, sand, glass,
guarantees longer life in heavy duty sugar).
conditions (heavy products, long distances It offers a wear life 5 times longer than acetal
and high operating speed). resin.
Operating temperatures: The mechanical characteristics are similar to
in air ( - 40°C a + 80°C ) those of acetal resin.
in hot water ( + 65°C ) The chain is not suitable to be used in wet
Inflammability: 94 HB. environments (can swell). Must use oil
Colour: LF ( brown ), WLF ( white ). lubricants.
Operating temperatures:
in air (- 5°C a + 100°C )
Inflammability: 94 HB.
Colour: black.
AS PC
Conductive resin Polycarbonate
Good electrical conductivity. Highly resistant to impact and to high
Reduces the accumulation of electrostatic temperatures.
charges. Maintains its rigidity and other mechanical
Lower mechanical characteristics. characteristics up to 130°C.
Load carrying capacity is 40 % lower than It is used only for PlateTop series 1873
Rex LF.® chains. In case of inclined layouts the rubber
Lubrication system is recommended for insert can be glued to the top slats.
sideflexing layouts. Operating temperatures:
The use of chain guide made of conductive in air (+130 °C )
material ( steel, stainless steel or conductive Inflammability: 94 V-2.
UHMWPE ) is recommended.
Materials
Colour: grey.
Operating temperatures:
in air ( + 60°C )
in hot water ( + 50°C )
Inflammability: 94 HB.
Colour: black.
It is recommended to always consult Rexnord
prior to installation.
WPP
Reinforced polypropylene
chemical agents resistant
Offers a mechanical resistance 20% higher
than ordinary PP polypropylene.
Has a higher dimensional stability ( the chain
flatness characteristics are enhanced ).
Lubrication system is recommended for
sideflexing layouts.
Operating temperatures:
in air ( + 5°C a + 115°C )
in hot water ( + 115°C )
Inflammability 94 HB.
Colour: white
5
Sprockets-Rubbers
FDA & USDA Thermoplastic sprockets Rubbers
PA PUR
Polyamide Thermoplastic rubber
High resistance to wear and impact. Hardness 90 Shore A.
Excellent dimensional stability even in relatively High wear resistance.
high temperatures. Operating temperatures:
Good resistance to chemicals. in air (- 40°C a + 100°C)
Operating temperatures: in hot water (+ 60°C)
in air (0°C a + 80°C) Colour: dark grey.
in hot water (+ 65°C)
Inflammability: 94 HB.
Colour: black.
SEBS SEBS
Thermoplastic rubber
PA FV Available in two hardness types:
45 Shore A (white)
Reinforced polyamide 60 Shore A (light grey)
Offers a better resistance to wear and to impact The lower hardness type has increased anti-
than PA resin. Has a higher dimensional slip properties, but reduced wear resistance.
stability. Operating temperatures:
Offers an increased operating temperature. in air (- 40°C a + 100°C)
Operating temperatures:
in air (- 5°C a + 120°C)
in hot water (+ 100°C)
Inflammability: 94 HB.
NBR
Colour: black.
Nitrile rubber
Hardness 60 Shore A.
Materials
Operating temperatures:
Glistamide R
FDA USDA
American institute (Food and Drug United States Department of Agriculture,
Administration), responsible for the cerfification responsible for the approval of components and
of materials to be in contact with food. machinery in the meat, poultry and dairy
For direct contact with food the following industries.
materials have been approved: The following chains have been approved :
• AISI 304 843, 845, 963, 879, 879 TAB, 880, 880 TAB,
• HP,TM
WLF
R
882 TAB, 1843, 1873, 2873, 3873, 1700, 1701,
1702.
6
Contents
Steel TableTop and Plate Top Chains
®
page 8 / 15
Chains page 16 / 29
Steel
TableTop ®
and
PlateTop
Chains
Steel TableTop ® chains are especially suitable for:
Steel • bottle transport (bottles in all shapes and sizes!)
• parts handling like bearings or gears
TableTop ® The above are just a few examples. Rexnord steel TableTop ®
chains can transport virtually anything!
Double hinge TableTop ® chains, for especially high demands with
Chains regard to
• strength
• wear resistance
Straight Running
812 - 815
40% higher strength,
OPTI-Plus ® = ground finish
9,8
S 815 - K400 101,6 3,0
Carbon Steel
6,6
S 815 - K450 114,3 1,8 150 3,3
S 815 - K 600 Heat Treated 152,4 4,2
S 815 - K750 190,5 5,1 3,15 6,35 38,1
Stainless Steel 80
SS 812-K325 0,3 82,5 2,8 2,6
Material No. 1.4016
SSR 812-K325 0,3 82,5 2,8 80 2,6
SSX 812-K325 0,18 82,5 2,6
42,1
44
K
SSY 812-K350 0,18 88,9 1,6 150 2,7
* = On request See
Pin material for S 815: case hardened steel. page 69/70/71
Pin material for SS 812: stainless steel AISI 304.
Pin material for all other chains: wear resistant stainless steel. 802 - 805
Standard length: 80 pitches 10 ft (3.048 m)
Stainless Steel
6,6
Austenitic
SSC 805 A- K750 Steel 190,5 1,8 150
Chrom Nickel 18/8
80,5
82,5
Pin material for SSC 805: stainless steel AISI 304. See
Pin material for all other chains: wear resistant stainless steel. page 72/73
Standard length: 80 pitches 10 ft (3.048 m)
G
Travel
9
Series 512. Chains with one inch pitch are recommended for all
applications involving the transport of small-sized products.
A further advantage is their compact design.
Steel
TableTop ®
Chains
Straight Running
512
G
Travel
10
Steel Naturally, the sideflexing version has same excellent properties as
the straight running chain.
TableTop ®
Chains
Sideflexing
881
6,6
S881-K325 Carbon Steel 82,5 457 44,5 41,4 2,9
S881-K450 Heat Treated 114,3 610 3,6
3,15 6,35 38,1
Pin material: case hardened steel See See
Standard length: 80 pitches 10 ft (3.048 m) page 93/97 page 74/75
GC
43
K
R
11,2 Travel
11
The higher demands placed on modern high-performance lines
with regard to efficiency, safety and noise reduction led logically to
the development of a new generation of sideflexing chains for:
Steel
• chains with bevelled guide shoes
• chains with hold-down tabs.
Its flatness and surface quality with circumferential chamfer as well
TableTop ®
8811
40% higher strength,
OPTI-Plus ® = ground finish
Travel 11,2
8811 TAB
GC
43
K
Travel 12,7
16,3
12
Steel
TableTop ®
Chains
Sideflexing
881 M
40% higher strength,
OPTI-Plus ® = ground finish
Magnetic System
9,8
SSC 881 M - K325 82,5 457 2,5
6,6
SSC 881M-K330 * 83,8 500 2,6
SSC 881M-K450 0,3 114,3 500 3,2 3,15
OPTI-Plus ® 45 44,2 6,35 38,1
SSC 881M-K750 190,5 500 4,9
SSX 881 M - K325 0,18 82,5 457 2,5
42 max
* = On request See See
GC
K
Pin material: wear resistant stainless steel page 95 page 69/70/71
Standard length: 80 pitches 10 ft (3.048 m)
R
Travel
13
Plate top chains with steel top plates are especially suitable for
heavy loads, long distances and high speeds.
The chain consists of a base roller chain with steel plates
Plate Top
welden on.
Similarly to the TableTop ® chains, various steel alloys are
available for the plates.
Chains
The gap between the plates is 1,6 mm wide.
With Steel Top Plates
Straight Running
1864
28,6
34,9
866
On request
41,3
37,3
K
14
Plate Top The sideflexing plate top chain utilizes the advantage of a precision
built base roller chain with "snap on" top plates to form a
continuous flat conveying surface.
Chains Hold-down tabs are used to provide positive retention in curves and
inclines.
A special version, the 4874 chain, is also available with angled top
With Steel Top Plates plates on one side. Although this chain can only sideflex to one
side, the special top plates minimize the flight gap opening.
Sideflexing
1874
Sideflexing: Steel and Stainless Steel Top Plates, 19.05 mm 3/4” Pitch
Radius
Rexnord min. GC
Material Width
Chain K R Straight Curve Weight
No. BaseChain TopPlate mm mm mm mm kg/m
Rd min. = 254
1874 - K325 82,5 381 4,2
14,3
1874 - K450 Steel Steel 114,3 381 34,1 34,6 4,8
1874 - K600 152,4 457 5,7
1874 - K750 190,5 610 6,4
3,15 5,08 19,05 19,05
1874 A - K325 82,5 381 4,2
1874 A - K450 Stainless 114,3 381 4,8
Steel Steel 152,4 457 34,1 34,6 5,7
1874 A - K600 ø11,91
1874 A - K750 190,5 610 6,4
31,75
57,15
GC
K
1874 SS- K325 82,5 381 4,2
1874 SS- K450 Stainless Stainless 114,3 381 4,8
12,6
1874 SS- K600 Steel Steel 152,4 457 34,1 34,6 5,7
1874 SS- K750 190,5 610 6,4
R
20,6 Travel
Standard length: 160 pitches 10 ft (3.048 m) See See
page 94 page 84 23,8
4874
Sideflexing: Steel and Stainless Steel Top Plates, 19.05 mm 3/4” Pitch
Radius
Rexnord min. GC
Material Width
Chain K R Straight Curve Weight
No. BaseChain TopPlate mm mm mm mm kg/m
Rd min. = 305
4874 A - K325 82,5 381 4,32
14,3
page 94 page 84
K
12,6
R
20,6 Travel
23,8
15
HP ™ Chains
• lowest friction coefficient of any
chain material
• 40% longer flight wear life
than plain acetal
• 25% longer flight wear life
than LF ® acetal
Thermo-
plastic
TableTop ®
and
PlateTop
Chains
Thermoplastic TableTop ® chains are especially suitable for
Thermo- transporting sensitive products such as cans, cartons, or PET
bottles.
plastic These chains are distinguished by their low noise level, as there
are no metal-to-metal contacts.
Plastic pins also available upon request with minimum order
TableTop ®
quantity, for LF and WPP chains.
820 chains also available in acetal grey upon request and minimum
order quantity.
Chains
Straight Running
820
HP TM
= High Performance
Plate thickness 4 mm
13,5
LF 820-K325 82,5 0,83 Rd min. = 40
LF 820-K343 87,0 0,85
7,2
LF 820-K350 LF ® 88,9 4 9,5 0,87
LF 820-K400 (Brown) 101,6 0,95
LF 820-K450 114,3 1,03 TT 6,35 38,1
LF 820-K600 152,4 1,25
LF 820-K750 190,5 1,47
HP 820-K325 82,5 0,83
42,1
44,5
HP 820-K343 87 0,85
K
HP 820-K350 88,9 0,87
HP 820-K400 HP TM 101,6 4 9,5 0,95
HP 820-K450 (Dark grey) 114,3 1,03
HP 820-K600 152,4 1,25
HP 820-K750 190,5 1,47 h Travel
Special materials
AS 820-K325 82,5 0,83
AS 820-K350 88,9 0,87
AS 820-K400 Anti-static AS * 101,6
4 9,5
0,95
AS 820-K450 (Black) 114,3 1,03
AS 820-K600 152,4 1,25
AS 820-K750 190,5 1,47
WRB 820-K325 82,5 0,83
WRB 820-K400 Wear resistant WRB 101,6 4 9,5 0,95
WRB 820-K450 (Black) 114,3 1,03
WRB 820-K750 190,5 1,47
WPP 820-K325 – 0,70
WPP 820-K350 – 0,74
WPP 820-K400
Reinforced polypropylene WPP ** – 0,82
chemical resistant – –
WPP 820-K450 – 0,90
(White)
WPP 820-K600 – 1,05
WPP 820-K750 – 1,20
Pin material: wear resistant stainless steel (only for WPP 820 : See
stainless steel AISI 316). page 76/77
* = Minimum order 100 metres.
** = WPP chain dimensions are larger than those indicated
in the drawing. For certified dimensions refer to our
Technical Department. Ask for Rexnord assistance for the use of
sprockets. Minimum order 100 metres.
Standard length: 80 pitches 10 ft (3.048 m)
17
The design of links allows overlapping of top plates,
thus creating a flat and continuous surface.
Series 831: Differs from the 820 series in the greater thickness of
Thermo-
plates (4,8 mm). Wear life increased by 40%.
Allows flush installation side by side of chain series:
821, 879, 879 TAB, 882 TAB.
plastic
821 chains also available in acetal grey upon request and minimum
order quantity. TableTop ®
Chains
Straight Running
831
HP TM
= High Performance
See
K
Travel h
821
Rd min. = 40
LF821K 750 190,5 2,50
LF ®
14,3
Travel 9,5
18
Chain equipped with side holding system “BEVEL” type on curved
Thermo- runs. Can be lifted on straight runs for cleaning and maintenance.
No possibility of jamming of broken glass.
plastic Series 879: Differs from the 880 series in the greater thickness of
plates (4.8 mm). Wear life increased by 40%.
Allows flush installation side by side of chain series:
TableTop ® 831, 821.
Plastic pins also available upon request with minimum order
quantity, for LF 880.
Chains
Sideflexing
880
HP TM
= High Performance
Plate thickness 4 mm
7,55
7,14
Rd min. = 40
LF 880 -K325 LF ® 82,5
4 16
457
44,5 41,4
0,89
20
LF 880 -K450 (Brown) 114,3 610 1,04
4 16 44,5 41,4
K
WRB 880-K450 (Black) 114,3 500 1,04
879
Rd min. = 40
LF 879 -K325 LF ® 82,5
4,8 15,2
457
44,5 41,4
0,93
20
K
R
h Travel
19
Chain equipped with “TAB” type side holding system on curved runs.
Positive holding capability,allows higher speed and greater loads.
TAB type guides offer also positive holding of the chain onto the
Thermo-
runners during return travel.
Series LF and HP 880TAB-K343. The width of 87 mm, allows the
design of multiple strand conveyors with gaps of 1 mm (instead of
plastic
5,5 mm), without any alteration of the pitch of 88 mm.
Old conveyors can be adapted for the conveying of PET bottles
with petaloid bottom, by simply changing the chains and chain
TableTop ®
guides.
Plastic pins also available upon request with minimum order
Chains
quantity, for LF 880 TAB.
Series 879 TAB. Differs from type 880TAB for the greater plate Sideflexing
thickness (4,8 mm). Wear life increased by 40%. Allows side by
side installation of chains type 831, 821, 882 TAB.
880 TAB
HP TM
= High Performance
Plate thickness 4 mm
Rd min. = 40
LF880TAB-K325 82,5 457 0,94
7,55
LF ®
20
GC
K
Special materials
AS880TAB-K325 Anti-static AS 82,5 500 0,94
4 11,5 16 46 44,2
R
879 TAB
No.
20
LF879TAB-K325 LF ® 82,5
4,8 11 15,2
457
46 44,2
0,98
38,1 TT LF879TAB-K450 (Brown) 114,3 610 1,14
GC
See See
Standard length: 80 pitches 10 ft (3.048 m) page 94/97 page 80 / 81
R
Travel G
h
20
Series 880BO. It differs from the 880TAB for the reduced curving
Thermo- radius (R min. = 200 mm). The use of lateral corner wheels allows
compact layouts and greater number of curves.
TableTop ®
Series 879BO. Small sideflexing radius (R min. = 200 mm).
Tangential sprocket. Small gap, better product support.
Conveyors with many corners are possible, compact dimensions,
Chains alpine accumulation systems, flat carousel conveyors.
Bidirectional.
Sideflexing
880 BO
7,55
No. Plate Material mm mm mm mm kg/m
7,14
Rd min. = 40
LF 880 BO-K325 LF ® 82,5
200 46 44,2
0,96
20
LF 880 BO-K450 (Brown) 114,3 1,11
4 38,1
Pin material: wear resistant stainless steel. See See
Standard length: 80 pitches 10 ft (3.048 m) page 89 page 80/81
42,9
61,1
GC
K
R
11,5 Travel
879 BO
K
R
11,8 Travel
21
Series 882 chains are heavy-duty TableTop ® chains with a level of
performance corresponding to that of the steel
TableTop ® chain 8811.
Thermo-
They are designed to convey larger and heavier products over
longer distances.
This chain is available in both versions, i.e. with hold-down tabs
plastic
and bevelled guide shoes.
TableTop ®
Chains
Sideflexing
882
Rd min. = 40
Chain K R Straight Curve Weight
No. Plate Material mm mm mm mm kg /m
9,5
GC
K
Travel 17,5
882 TAB
HP TM
= High Performance
Rexnord GC
Width min.
9,5
GC
22
New Rex Curve Master ™ sideflexing chains with the exclusive
Thermo- LPC ™ design can be lifted out in curves and straights for easy
cleaning and conveyor maintenance.
plastic The LPC ™ system features Low Pin Centerline chains and
wearstrips that hold CurveMaster chains down in corners, without
the restrictions of tabs, bevels, or magnets. LPC ™ chain stays flat
Sideflexing
LPC 279
CurveMaster TM
16,7
LPC 279-K325 82,5 1,16 Rd min. = 70
7,14
LPC 279-K450 LF ® 114,3 457 44,5 44,5 1,31
LPC 279-K750 (Brown) 190,5 1,78 24,2
Pin material: wear resistant stainless steel. See See 4,8 38,1
Standard length: 80 pitches 10 ft (3.048 m) page 96 page 80/81
42,9
GC
K
The Curve Master LPC ™ system
R
19,4 Travel
T = The tension on the chain from
the drive motor (chain pull)
F = The resulting force driving the
chain against the inner
wearstrip in a corner.
R = The reaction of the corner
against the chain.
M = Reacting couple applied to
the chain.
The reacting couple (M) tends to lift the In the guide system LPC ™(Low Pin Centerline)
chain the reacting couple (M) tends to keep the chain
flat.
23
Series 880TAB-K454. The base chain is similar to series 880TAB
except for the side flaps which act as guide for the product
transported.
Thermo-
plastic
TableTop ®
Chains
Sideflexing
GC
K
11,5
Travel
16
24
Thermo- Series RR882.The base chain is similar to the 882TAB except for
the stiffening ridges which permit the use of transfer combs.
It is recommended for end of run head transfer where the use of
plastic dead plates may create product stability problems.
TableTop ®
Chains
Sideflexing
RR 882
15,9
No. Plate Material mm mm mm mm kg/m Rd min. = 76
LF ®
33,3
8,73
RR 882TAB-K450 114,3 610 60 58 2,40 11,1
(Brown)
57,2
76,2
GC
K
112,7
25
La configurazione delle maglie consente la sovrapposizione delle
tapparelle, creando una superficie continua e piatta.
Serie 831. Si differenzia dalla 820 per lo spessore delle tapparelle
maggiorato (4,8 mm). Durata all' usura superiore del 40 %.
Consente l' affiancamento laterale senza dislivelli con le catene
821, 879, 879 TAB, 882 TAB.
843
Chain K Weight
No. Base Chain Top Plate mm kg /m
LF ®
K
845
page 84
Travel 11,5
26
Plate Top A roller chain ANSI 60 (pitch 19,05 mm) is used as base chain .
The top plates are clipped on the protruding pins and are
replaceable. They permit a greater loading capacity, higher speed
Chains and longer runs with a single power traction unit. Quieter gearing
operation.
Series 963. The Top plates are designed for overlapping.The
continuous surface facilitate stability and ease operations with
With Thermoplastic Top Plates unstable products. Uni-directional travel.
Straight Running
963
14,3
(Brown)
LF 963-K750 * 190,5 2,68
LF 963SS-K325 82,5 2,10 4 5,08 19,05 19,05
LF 963SS-K450 Stainless LF ® 114,3 2,23
LF 963SS-K600 * Steel (Brown) 152,4 2,53
LF 963SS-K750 * 190,5 2,68 ø 11,91
Standard length: 160 pitches 10 ft (3.048 m) See
34,1
36,5
K
* = On request page 84
12,6
19 Travel
27
They have a greater loading capacity, allow higher speeds and lon-
ger runs with single power traction units. They are indicated for step
by step positioning.
Plate Top
Quiter gearing operation. The top plates are clipped on the
protruding pins of the chain and are replaceable.
Series 1843. The base chain is a standard roller chain Side Bow
Chains
ANSI 40 SB (pitch 12,7 mm). The small pitch reduces the sagging
effect and permits the use of smaller sprockets. Uni-directional With Thermoplastic Top Plates
travel.
Series 1873. The base chain is a roller chain Side Bow 60 SB Sideflexing
(pitch 19,05 mm). Bi-directional travel.
PC 1873 chains are recommended for receiving glued rubber
inserts (inclined runs).
1843
31,8
page 84
GC
K
Travel 10,9
R
13,95
1873
28
Plate Top One application for this chain is the transport of trays in self-service
restaurants.
The "snap on" overlapping plastic top plates (acetal or
2873
16,7
Radius GC
Rexnord Material Width min.
Chain K R Straight Curve Weight
6,4 7,92 38,138,1
No. Base Chain Top Plate mm mm mm mm kg/m
D 2873-K1000 Steel
Acetal 254 660 39,7 41,0 3,4
Stainless (White) ø 11,91
D 2873SS-K1000 Steel
37,3
62,7
GC
K
12,6
LF 2873-K1000 Steel
LF ® 254 660 39,7 41,0 3,4
R
Stainless (Brown)
LF 2873SS-K1000 Steel
22,2
Standard length: 80 pitches 10 ft (3.048 m) See Travel
page 84
27
3873
Rexnord Material GC
Width min.
Chain K R Straight Curve Weight 6,4
No. Base Chain Top Plate mm mm mm mm kg/m
20,6 5,08 19,05 19,05
LF 3873-K1000 Steel
®
LF 254 457 33,3 34,6 3,1
Stainless (Brown)
LF 3873SS-K1000 Steel
ø 11,91
WLF 3873-K1200 Steel
31,8
57,2
GC
LF ®
K
29
• for inclines up to 25 degrees
• rigid design
• positive guiding system
Chains for
Incline
Conveying
Steel TableTop ® chains with vulcanized rubber coating make it possible
to transport products which tend to slide easily.
With regard to service life and safety, the robust design has proved
Chains
With Rubber Top
SSR 812
9,8
SSR 812-K325 Cr-Ni Steel 82,5 2,8 80 2,8 3,15
6,6
Rubber Top
K
G
Travel
Rubber Top
Pin material: wear resistant stainless steel See See 6,35 38,1
Antislip insert material: NBR rubber (black) page 97 page 74/75
60 Shore A hardness.
Standard length: 80 pitches 10 ft (3.048 m)
56,2
45
43
12,7 G
16,3 Travel
31
TableTop ® chains with vulcanized rubber coating make it possible
to transport products which tend to slide easily.
With regard to service life and safety, the robust design has proved
Steel
itself superior to other systems.
Through the use of the guide shoe concept, goods may be
conveyed directly from straight running to the inclination and also
TableTop ®
around corners.
Chains
With Rubber Top
SSC 802
140
K
G
Travel
GC
43
K
Travel 12,7
16,3
32
Thermo- The thermoplastic TableTop ® chains with rubber insert, series HFP,
have rubber inserts moulded into the topplates. These chains are
suitable for conveyors with an inclination up to 25°, depending on
TableTop ®
Chains
With Rubber Inserts
HFP 820
13,5
HFP 820-K325 82,5 65,0 0,83
HFP 820-K350 SEBS rubber 88,9 88,9 0,87
LF ®
7,2
HFP 820-K400 (light grey) 101,6 101,6 0,95
HFP 820-K450 (Brown) 60 Shore A 114,3 114,3 1,03 4
HFP 820-K600 152,4 135,0 1,25 6,35 38,1
2
Pin material: stainless steel. See
On request: Antislip insert in: page 76/77
SEBS rubber (white), 45 Shore A hardness.
A*
42,1
44,5
PUR rubber (dark grey), 90 Shore A hardness.
K
Chains series K350, K400, K450 are obtained by cutting the K600 series.
Standard length: 80 pitches 10 ft (3.048 m)
HFP 821
Special configurations
on request. Indicate the
distance between inserts 9,5 14
at the time of ordering.
38,1 38,1 Travel
33
The thermoplastic TableTop ® chains with rubber inserts, series
HFP, are also available in sideflexing execution. This make them
suitable for applications with curves and installations with
Thermo-
horizontal and inclined sections.
plastic
TableTop ®
Chains
With Rubber Inserts
42,9
GC
K
Special configurations
R
SEBS rubber
LF ®
7,55
(Brown) 60 Shore A
38,1 2
Pin material: stainless steel. See See
On request: Antislip insert in: page 89 page 80 / 81
SEBS rubber (white), 45 Shore A hardness.
PUR rubber (dark grey), 90 Shore A hardness.
61,1
42,9
Special configurations
R
34
Thermo- The antislip insert fitted during moulding consents inclined
conveying with grades up to 25°. The rubber used for the inserts
has a hardness of 60 Shore A standard. Different hardness 45 or
HFP 879 BO
8,35
7,14
Material Radius
Rexnord Width min. GC
20,8
Chain Antislip K A R Straight Curve Weight
No. Link insert mm mm mm mm mm kg/m
4,8 38,1
® SEBS rubber
HFP 879BO-K450 LF (light grey) 114,3 102 200 46 44,2 1,20
(Brown) 60 Shore A
61,5
GC
A
K
SEBS rubber (white), 45 Shore A hardness.
PUR rubber (dark grey), 90 Shore A hardness.
Standard length: 80 pitches 10 ft (3.048 m)
R
11,8 11,4
Special configurations Travel
on request. Indicate the
distance between inserts
at the time of ordering.
38,1 38,1
9,5
LF ® (light grey)
4,8
HFP 882TAB-K1000 254 195 610 60 58 2,87
(Brown) 60 Shore A
HFP 882TAB-K1200 304,8 246 3,41 2 38,1
Pin material: stainless steel. See See
On request: Antislip insert in: page 94/97 page 82/83
SEBS rubber (white), 45 Shore A hardness.
PUR rubber (dark grey), 90 Shore A hardness.
Standard length: 80 pitches 10 ft (3.048 m)
57,2
76,2
GC
A
Special configurations
R
35
The antislip insert fitted during moulding consents inclined
conveying with grades up to 25°. The base chain is a standard
roller chain Side Bow ANSI 60 SB (pitch 19,05 mm).
Plate Top
The replaceable top plates are clipped on the protruding pins of the
base chain. Longer runs can be designed with a single power
traction unit.
Chains
The TAB guides permit to continue either from an inclined run to a
plane one or viceversa.
With Thermoplastic Top Plates
With Rubber Inserts
HFP 1877
Rd min. = 150
Chain K A R Straight Curve Weight
No. Base Chain Top Plate mm mm mm mm mm kg /m
4,8 HFP1877-K 325 82,5 82,5 2,60
HFP1877-K 350 88,9 88,9 2,65
19,05 19,05 5,08 2 HFP1877-K 450 114,3 114,3 2,80
HFP1877-K 600 Steel LF ® 152,4 132,0 380 33,3 34,6 2,90
HFP1877-K 750 (Brown) 190,5 132,0 3,10
HFP1877-K1000 254,0 195,0 3,40
ø 11,91 HFP1877-K1200 304,8 245,0 3,60
31,75
A*
12,7
GC
57
Special configurations
on request. Indicate the
distance between inserts
at the time of ordering.
38,1 38,1
36
Thermo- Series HFP 821 F. The base chain is the same as for the 821
series. The rubber pusher fin insert is applied during the moulding
process. The chain is recommended as a substitute for belt
Chains
With Pushers
HFP 821 F
14,3
®
LF
38
HFP 821-K1000 F (dark grey) 254 214 2,85
(Brown)
7,94
HFP 821-K1200 F 90 Shore A 304,8 265 3,17
Special configurations
136,5
on request. Indicate the 140
A
K
distance between pushers
at the time of ordering.
38,1 38,1 38,1
9,5 Travel
PUR rubber
HFP 882TAB-K750 F LF ® (dark grey) 190,5 132 610 60 58 2,43 4,8
(Brown) 90 Shore A
38,1
76,2
GC
A
Special configurations
on request. Indicate the
R
37
• to lift , to lower, to turn over (rinsing
machines)
• for bottles, tins, jars, boxes, cartons,
bundles, parcels, industrial
components
• up to 60 mt/min. conveying speeds
• soft rubber gripper elements (to
avoid product damaging)
Gripper
Chains
Gripper Chains fitted with steel top plates to be used in abrasive and heavy
duty conditions or in case of high temperatures. The base is a
standard roller chain Side Bow ANSI 60 SB (pitch 19,06 mm).
Chains The gripper elements are available in the “GD” type (Smooth pad)
and “GJ” (Grooved pad). They are clipped on and easily
replaceable .
With Steel Top Plates Series 1874 G. The clip for the TAB guide is welded on the top
plate .
Series 1874 HDG. It differs from the 1874 G series for the shape of
the top plates (Guide and top plate are a single unit). This series
uses the same type of guiding system. The tensile stress is 15%
higher. Reduced stretching during operation. The chain is designed
for 50 % higher loads.
1874 G
Sideflexing: Steel and Stainless Steel Top Plates, 19.05 mm 3/4” Pitch
Material Radius
Rexnord Ultimate min. GC
Width
Chain Strgth. Base K R Straight Curve Weight
No. N Chain TopPlate mm mm mm mm kg/m
1874 - K363GD
1874 - K363GJ 27000 Steel Steel 92,1 381 34,1 34,9 5,6 GD GJ
1874 A-K363GD 27000 Steel Stainless
92,1 381 34,1 34,9 5,6
44,4
1874 A-K363GJ Steel
27
1874 SS-K363GD 21000 Stainless Stainless 92,1 381 34,1 34,9 5,6
1874 SS-K363GJ Steel Steel 33,3
23,8 5,08 19,05 19,05
EPDM rubber gripper elements (black). See
40 shore A hardness. page 84
12,6
White grippers available upon request.
Standard length: 160 pitches 10 ft (3.048 m) ø 11,91
86,1
31,8
57,2
GC
K
R
20,6 Travel
1874 HD G
Sideflexing: Steel and Stainless Steel Top Plates, 19.05 mm 3/4” Pitch
Material Radius
Rexnord Ultimate min. GC
Width
Chain Strgth. Base K R Straight Curve Weight
No. N Chain TopPlate mm mm mm mm kg/m
1874 HD-K363GD
1874 HD-K363GJ 31000 Steel Steel 92,1 400 34,1 34,9 6,3
GD GJ
1874 HDSS-K363GD 24000 Stainless Stainless
1874 HDSS-K363GJ Steel Steel 92,1 400 34,1 34,9 6,3
44,4
27
ø 11,91
86,1
32,5
56,5
GC
K
R
21 Travel
39
The thermoplastic top plates other than providing a quieter and
smoother operation, make it possible to reduce the plant weight,
increase conveying speed and permit dry service.
Gripper
The gripper elements are available in the “GD” type (Smooth pad)
and “GJ” type (Grooved pad). They are clipped on and easily
replaceable.
Chains
Series 1843 G. The base is a standard roller chain Side Bow ANSI With Thermoplastic Top Plates
40 SB (pitch 12,7 mm). It is recommended for the conveying of
ampoules, test tubes and other minute products such as small
industrial components.
Series 1873 G. The base is a standard roller chain Side Bow ANSI
60 SB (pitch 19,05 mm).
1843 G
LF1843SS-K125GJ Steel
25,3
EPDM rubber gripper elements (black). See
12,7 12,7 3,65 13,9 40 shore A hardness. page 84
White grippers available upon request.
ø 7,85 Standard length: 240 pitches 10 ft (3.048 m)
7,75
31,8
19,8
31,8
GC
K
Travel 11,1
1873 G
57,2
31,8
86,1
GC
K
Travel 20,6
40
Gripper The base chain is the same as series 882 TAB.
Economical version. It is recommended for corrosive environments
and for lower speed and reduced loads. The gripper elements are
Chains available in the “GD” type (Smooth pad) and “GJ” type (Grooved
pad). They are clipped on and easily replaceable.
882 G
39,7
40 shore A hardness.
23
White grippers available upon request.
8,73
35
Standard length: 80 pitches 10 ft (3.048 m)
22,2
38,1
86,1
57,2
76,2
GC
K
R
17,5 Travel
41
The base chain is a standard roller chain Side Bow ANSI 60 SB
(pitch 19,5 mm). The top plates are clipped on the protruding pins
of the chains and are replaceable.
Gripper
Series 1873 GJM. The gripper elements are moulded from
thermoplastic rubber. Recommended for the packaging industries. Chains
With Thermoplastic Top Plates
1873 GJM
ø 11,91
57,15
31,75
12,7
GC
73
K
R
R
Travel 20,6
42
The thermoplastic Gripper chains, serie 880 are suitable for
Gripper elevators light/medium weight products.
Chains
880 GB
7,55
7,14
LF 880TAB-K325GB 82,5 457 46 44,2 0,96
(Brown)
20
Pin material: stainless steel.
17
See
Gripper elements in PUR rubber (dark grey). page 80/81
4 38,1
90 shore A hardness. On request SEBS rubber (light grey).
60 shore A hardness.
Standard length: 80 pitches 10 ft (3.048 m)
42,9
61,1
GC
57
K
R
11,5 Travel
880 BO GB
13
Pin material: stainless steel. See 4 38,1
Gripper elements in PUR rubber (dark grey). page 80/81
90 shore A hardness. On request SEBS rubber (light grey).
60 shore A hardness.
42,9
61,1
K
R
11,5
Travel
43
• for systems where products
accumulate
• low friction coefficient between
chain surface and product (0,07)
• new SLPB series in HP ™
(High Performance) for superior
service
• silent operation
• high stability of product
Low
Backline
Pressure
Chains
Low The new chain series XLBP 831 in Rex-HP ™ ( High Perform-
ance ) material can guarantee superior performance and reduced
noise
Pressure
Chains
Thermoplastic
XLBP 831
HP TM
= High Performance
22,6
28,7
19,3
0,6 42,1 6,35 38,1
44,5
K
9,4 Travel
45
The base chain is the same as the 821 series. The two types of
chain differs for the material and for the fixing method of the roller
pins (safety hold system for the SLBP821 series).
Low
Serie SLBP 821. The safety hold system used for the roller pins is
guaranteed by positive double retention (one end has conical
coupling and the other is knurled).
Backline
Rex-HP ™ (High Performance) material guarantees superior
service and reduced noise. Product friction and accumulation
pressures are reduced by 20 % with single power traction unit.
Pressure
Chain wear as well as chain sagging are also lower. The roller pins
have inner supports for an improved stability and better product
flow.
Chains
Thermoplastic
LBP 821
Travel 9,5
SLBP 821
HP TM
= High Performance
Travel 9,5
46
Series SLBP882 TAB. The base chain is the same as the
Low 882 TAB series. Rex-HP ™ (High Performance) material
guarantees superior service and reduced noise.
Pressure system (one end has conical fitting and the other is knurled).
The roller pins have inner supports for an improved stability and
better product flow.
Chains
Thermoplastic
24
41,5
8,73
Pin material: stainless steel. See See 19,3
Standard length: 80 pitches 10 ft (3.048 m) page 98/99 page 82/83 0,6 38,1
57,2
76,2
GC
K
R
17 Travel
HP TM
= High Performance
K
R
17 Travel
47
Series SLBP882 TAB. The base chain is the same as the
882 TAB series. Rex-HP ™ (High Performance) material
guarantees superior service and reduced noise.
Low
Product friction as well as accumulation pressures are reduced by
20% (with single power traction unit). Reduced wear and chain
sagging. Roller pin holding is guaranteed by a double retention
Backline
system (one end has conical fitting and the other is knurled).
The roller pins have inner supports for an improved stability and
better product flow.
Pressure
Chains
Thermoplastic
HP TM
= High Performance
Width min.
Chain K R Straight Curve Weight
24
41,5
GC
K
Travel 17
48
Low Series LBP 883. These low backline pressure chains have been
designed for conveying large or packaged products.
The LBP 883 can be used on straight running and sideflexing
Backline conveyors.
Due to the favorable backline pressure conditions, a maximum
protection of the goods being conveyed is obtained.
Thermoplastic
24
41,5
8,73
LBP 883TAB-K450 LF ® 114,3
610 60 58
2,5
LBP 883TAB-K750 (Brown) 190,5 3,4 19,3
73
K
R
17 Travel
LBP 879 BO
(Brown)
7,14
42,9
61,5
K
R
11,8
Travel
49
The base chain is the same as the 821 series.
The shape of the rollers permits the use of transfer combs, which
can be installed instead of the dead tables at end of run transfers
Low
where product stability may create problems.
Backline
Pressure
Chains
Thermoplastic
FLBP 821
Left Right
Travel 9,5 6,4 93,7 93,7
3,8 42,9 23,5 23,5 42,9
7,5
13,5
25,4
25,4
69,8
69,8
120,7
120,7
Travel
50
The base chain is the same as the 882 TAB series.
Low The shape of the rollers permits the use of transfer combs, which
can be installed instead of the dead tables at end of run transfers
Pressure
Chains
Thermoplastic
LF ®
24
FLBP 882TAB-K375 95,2 667 60 58 3,6
41,5
8,73
(Brown)
Pin material: stainless steel. See See
19,3
Standard length: 80 pitches 10 ft (3.048 m) page 98/99 page 82/83 0,6 38,1
57,2
76,2
GC
K
Transfer comb for FLBP 882 TAB: in Reinforced Polyamide (black)
R
17 Travel
6,4 92,5
3,8 42,9
7,5
13,5
25,4
69,8
120,7
51
• the unique solution to special
problems!
• virtually nothing is impossible with
the Rexnord Multiflex chain
• for corner turns in the most confined
spaces
Catene Multiflex
Multiflex Chains
Multiflex Series 1700 K. The use of lateral corner disks guarantees the
design of compact systems of different configurations and with
increased number of curves. In the accumulation area is possible
to realise 60-70 mt. runs with a single power traction unit. It is
Chains recommended for the food and packaging industries (transfer of
beverage containers “Brick” / “Pack” types or similar, cans,
boxes). Suitable also for conveying of free pallets for the
Thermoplastic mechanical and automotive industries.
Series 1700 TAB K. The base chain is similar to the 1700 K. The
TAB guides consent tranfers from flat to inclined runs and
viceversa. Can be used in curves either with or without corner
In chains of the series ...K disks.
the fastening of the
connecting pins is
guaranteed by a double
system: one end is conically
fitted and the other is knurled.
1700 K
HP TM
= High Performance
Rd min. = 50
Sideflexing: 50 mm Pitch
12
24
Radius GC
Rexnord Material min. 50 8
Chain R Straight Curve Weight
No. Link Pin mm mm mm kg/m 3
GC
C 1700K Acetal D (White) Stainless Steel
55
B 1700K Zinc Plated
WLF 1700K LF ® (White) Stainless Steel
Travel
R
LF 1700K Zinc Plated 140 58 - 1,26
A 1700K LF ® (Brown)
Stainless Steel
1700 TAB K
Rd min. = 50
Sideflexing: 50 mm Pitch
12
Radius
24
GC
Rexnord Material min. 6
Chain R Straight Curve Weight 50 8
No. Link Pin mm mm mm kg/m
3
WLF 1700TABK LF ® (White) Stainless Steel 140 58 58 1,30
GC
67
55
See
Travel
page 100
53
Series AC 1700 C. The base chain is the same as the 1700 K
series. The top surface is made of hardened steel therefore highly
resistant to wear.
Multiflex
It is highly recommended for the mechanical and automotive
industries (transport and accumulation of metallic products with
sharp edges, rough casting surfaces etc.)
Chains
Series 1701. The chain features inclined guide sides.This guiding Thermoplastic
system tend to hold the chain when curving, at the same time
allows easy chain removal for cleaning operations. Bi-directional
travel.
AC 1700 K
GC
14
1701
Sideflexing: 50 mm Pitch
Rd min. = 50 Radius GC
12,7
53,2
GC
Travel
R
54
Series 1790K. The base chain is the same as the 1700 K series.
Multiflex The configuration of the top surface presents a lower supporting
area with consequent reduced product stability. Sliding type
Chains turning system. (Does not permit the use of corner discs).
Series 1701 TAB K. The base chain is the same as the 1790 K
series. The TAB guides consent transfers from flat to inclined runs
and viceversa.
Thermoplastic
1790 K
Sideflexing: 50 mm Pitch
Radius GC
Rd min. = 50
Rexnord Material min.
Chain R Straight Curve Weight
12
24
No. Link Pin mm mm mm kg/m
50 8
WLF 1790K LF ® (White) Stainless Steel 140 58 58 1,26
55
Accessories: pin extractor (see page 92). page 86/87
Standard length: 200 pitches 32.8 ft (10 m)
Travel
R
1701 TAB K
Sideflexing: 50 mm Pitch
Radius GC Rd min. = 50
Rexnord Material min.
Chain R Straight Curve Weight
12
6 50 8
WLF 1701TABK LF ® (White) Stainless Steel 140 58 58 1,30
67
55
Travel
55
These chains feature flush guide sides to guarantee a more
efficient sanitation. Sliding type turning system. Recommended for
the dairy and food industries.
Multiflex
Series 1702. Similar to the 1716 K series except for the material
(which is FDA approved for direct contact with food stuff) and for
the bi-directional use.
Chains
Thermoplastic
1716 K
Sideflexing: 50 mm Pitch
Rd min. = 50 Radius
12,5
Rexnord Material GC
min.
Chain R Straight Curve Weight
25
Travel
R
Curve
2°
1702
Sideflexing: 50 mm Pitch
Radius GC
Rd min. = 50
12,7
GC
Travel
R
Curve
2°
56
Series 1755. Reduced pitch (40 mm) Can be used with corner
Multiflex discs. Recommended for light duty (empty cans).
Series A 3150. High load carrying capacity (tensile stress 19600N).
Thermoplastic
1755
Rd min. = 40
15,5
Sideflexing: 40 mm Pitch
9,1
Radius GC
Rexnord Material min. 40 4
Chain R Straight Curve Weight
No. Link Pin mm mm mm kg/m
3
27,8
GC
1755 LF ® (Brown) Stainless Steel 136,5 30,5 - 0,37
R
Pivot material: polyamide. See See Travel
Standard length: 152 pitches 20 ft (6.080 m) page 92 page 87
A 3150
Sideflexing: 80 mm Pitch
Radius
Rexnord Material min.
Chain R Weight Rd min. = 125
No. Link Pin mm kg/m
24
48
A 3150 LF ® (Brown)
54,5
102
71
38 Travel
R
57
The base chain is the same as the1700 K series. The Top plates
have a large, uniform and continuous surface. Both type of chains
can be used with turning wheels. They cannot be curved upwards
Multiflex
or downwards.
Chains
Thermoplastic
1710 K
Sideflexing: 50 mm Pitch
Radius GC
Rexnord Material min.
Rd min. = 0 Chain R Straight Curve Weight
No. Link Top plate /Pivot mm mm mm kg /m
22
LF ®
34
30
Travel
1710 TAB K
Sideflexing: 50 mm Pitch
Radius GC
Rexnord Material min.
Rd min. = 0 Chain R Straight Curve Weight
No. Link Top plate /Pivot mm mm mm kg /m
22
(White)
24
67
R
24
Travel
30
58
The base chain is the same as the 1700 K series. The riveting of
Multiflex the Top plates to the links is guaranteed even in case of repeated
impacts.
Chains The chain design ensures the overlapping of the Top plates even
with very tight turning radiuses.
It is recommended for use when particular safety requirements for
the protection of hands and clothing have to be observed.
Thermoplastic The materials are FDA approved. Sliding type curving system .
1713 K
Sideflexing: 50 mm Pitch
Radius GC
Rexnord Material min.
Chain R Straight Curve Weight Rd min. = 1000
No. Link Top plate mm mm mm kg/m
23
35
LF ®
24
WLF 1713K (White) Acetal D (White) 500 58 58 2,70
7 50 8
Material: See
Pin in stainless steel. page 86/87
Polyamide pivot.
Inox AISI 304 rivet.
Accessories: pin extractor (see page 92).
253
GC
55
Standard length: 200 pitches 32.8 ft (10 m)
R
28 Travel
1713 TAB K
Sideflexing: 50 mm Pitch
Radius GC
Rexnord Material min.
Chain R Straight Curve Weight
No. Link Top plate mm mm mm kg/m
Rd min. = 1000
WLF 1713TABK ® Acetal D (White) 500 58 58 2,75
LF (White)
23
35
24
67
55
R
22 Travel
28
59
• for the toughest jobs
• simple design
Case
Conveyor
Chains
A new series of conveying chains with a simple two piece
Case construction.
Hard wearing acetal which provides highly resistant wear surfaces
and a low coefficient of friction.
Conveyor Stainless steel pins provide for articulation and flexing of the chain
and utilise a simple but effective method for retention in the
A 600
A 1400
H
Diameter Sprocket of
Rexnord Pitch Width of pin Face Sidebar E p
Chain p K E B H Weight
No. Material mm mm mm mm mm kg/m
K
B
A 600 Acetal 63,5 43 11 14,3 29 1,44
A 1400 Acetal 82,5 50 11 15,9 38 2,08
Travel
Pin material: stainless steel See R
All chains will flex around a 600 mm radius. page 85
Colour: white.
Standard length A 600: 96 pitches 20 ft (6.096 m)
Standard length A 1400: 74 pitches 20 ft (6.105 m)
A 600 TAB
A 1400 TAB
61
Special
Chains
Special Series 1108. Recommended for packaging machines of the
pharmaceutical, cosmetic and food industries.
When installed laterally to the base chain it eases product
1108
12
ZN 1108 Zinc plated
Acetal D (White) 32 0,51
SS 1108 Stainless Steel
4 12,7 2
Standard length: 395 pitches 16.4 ft (5 m) See
page 88
6,2
8,1
Chain guides
K
8,1
7,1 7,1 Use a T section for double roller
2,3
1080
Rd min. = 0
Sideflexing: Articulated chain with top plates
27
12
ø 11
48
Radius
Rexnord Width min.
Chain K R Weight + 0,35
No. Material link/ top plate mm mm kg/m 63,5 0
Travel
R
63
The Rubber-Top chain 35 RT K1700 is especially developed for
inclined conveyors for crates, trays and boxes.
The rigid slats of the chain have a vulcanized, specially shaped
Rubber-Top
surface to ensure maximum grip. The system is designed for an
inclination of 20 degrees and a max difference in height of 5,7 mtrs.
For proper function of this chain special kits for support are
Chains
available.
Straight Running
35 RT
page 88
Technical information:
• Max. working load: 7000 N
• Max. weight/linear M: 90 kg/M
+1
465 –
The chain features a system of guides designed for modular assembly. The system
of modular assembling of the intermediate straight guides ( see 35 RT 327) permits the
Travel realisation of conveyors of different lengths depending on the number of guides used.
It is possible to assemble a maximum of 11straight guides.
35RT328 ST 35
35RT327
35RT328
ST 35
H
I = Span
0 H = Rise
150 L = 1500 x No. of straight
L
20° guides used (1500: is
the length of 1 straight
I guide, see 35RT327)
According to the span (I ) and the rise required (H), the table gives:
- number of straight guides (35 RT 327) to be used.
- length (L ).
- total length of the chain.
Example: to design a conveyor with span I = 8196 mm and rise H = 2603 mm, is
necessary to use No. 5 straight guides ( 35 RT 327 ). The corresponding length L is 7500
mm, and the total length of the chain is 17863 mm.
Length L (mm)
1500 3000 4500 6000 7500 9000 10500 12000 13500 15000 16500
No. of straight 1 2 3 4 5 6 7 8 9 10 11
guides (35 RT 327)
H (mm) 551 1064 1577 2090 2603 3116 3629 4142 4655 5168 5681
I (mm) 2558 3968 5377 6787 8196 9606 11015 12425 13834 15244 16654
Total length of 5863 8863 11863 14863 17863 20863 23863 26863 29863 32863 35863
chain (mm)
64
Rubber-Top guides
for Series 35 RT
Part. 435
35RT435
The chain feature a modular system for assembling Part. 328
35RT 328
the guides which consent upgrading or downgrading
layouts with fixed 20% grade.
35RT327
Part. 327
Part. 328
35RT328
500 100
+
20° 253 517 – 1
19,8
38
38
122
161
74
74
150
83
38
R 305 20° 33 33
ST 35
+
R 225 517 – 1
38
38
150
74
122
38
168,5
240
117
20°
ST 35 100 500 33 33
Use self-locking
150
74
of the conveyor
frame to prevent 375 750 375 33
vibrations loosening 1500 R10,5 42
the fixture
21
2,5
82
41
25
M8
35 RT 327
M8
ø 40
65
As base chain is the same as the 880 BO series.
The moulded pushing fin permits to transport round products
(gears, bearings etc.)
Thermo-
Reduced turning circle (R min = 200 mm), possibility of lateral
traction. plastic
TableTop ®
Chains
With Pushers
880 BO F
Special configurations
on request. Indicate the
71,5
61,1
42,9
GC
K
4 11,5
33
Travel
66
Vacuum Recommended for single strand vacuum systems (empty aluminium
cans). Substitutes the magnetic system.
Series 820 Vacuum. The base chain is the same as the 820 series.
820 Vacuum
V3
13,5
LF 820 -K325V2 82,5 6,5 – 19 0,83
7,2
LF 820 -K350V2 88,9 4 – 45 0,87
LF ® 4
LF 820 -K450V2 I30 (Brown) 114,3 8 – 30 1,03
6,35 38,1
42,1
K
I
LF 820 -K325V3 LF ® 82,5 7,9 4,4 20 0,83
(Brown)
I d2
V3 - Three holes
V2
V1
Sideflexing: Single Hinge, 38.1mm 11/2” Pitch
Radius
Rexnord Width Hole dia. min. GC
Chain K d1 I R Straight Curve Weight
No. Material mm mm mm mm mm mm kg/m
7,55
Rd min. = 40
7,14
V1 - One hole
20
(Brown)
LF 880 TAB-K450V2 114,3 6 24 610 46 44,2 1,08
Pin material: stainless steel. See
R
V2 - Two holes
67
Sprockets
and Idler
Wheels
Corner
Tracks and
Straight
Tracks
Sprockets
for Series 812, 815, 881 M, SSR 812 Rubber Top
– 0,05
d1 – 0,1
NS 815 T21 R... 21 10,5 129,26 129,5 25 30 35 40 45 52 51 0,47
ø 60
NS 815 T23 R... 23 11,5 141,22 142 25 30 35 40 45 52 51 0,55
da
NS 815 T25 R... 25 12,5 153,21 154,2 25 30 35 40 45 54 58,5 0,60
Bore ( inch)
L
NS 815 T21 R... 21 10,5 129,26 129,5 1" 11/4" 2" 52 51 0,47
NS 815 T23 R... 23 11,5 141,22 142 1" 11/4" 11/2" 1 3/4" 2" 52 51 0,55 Ln
NS 815 T25 R... 25 12,5 153,21 154,2 1" 11/4" 11/2" 2" 54 58,5 0,60
Material: sprocket in reinforced polyamide (black). Keyway: UNI 6604-69. See page 104.
Bolts in stainless steel AISI 304, nuts in Max recommended tightening torque: 1 kgm.
nickel plated brass.
– 0,0 5
NS 815 T29 R... 29 14,5 177,24 179 75 87 0,66
– 0,1
ø 105
Material: sprocket in reinforced polyamide (black). Max recommended tightening torque: 1 kgm.
d1
da
Bolts and nuts in stainless steel AISI 304. Use: tunnel washing machines, wide
Keying to tubular shaft with ø12 cylindrical pin. accumulation tables.
40
52
20 •
d1 – 0,1
da
69
Sprockets
for Series 812, 815, 881 M, SSR 812 Rubber Top
S 815 - SS 815 815 Guide Rings, Steel (S), Stainless Steel (SS)
53,2
Rexnord Outside
42,9 Order No. No. of Dia.
Teeth of da Thickness Weight
Steel Stainless steel Sprocket mm mm kg
S 815 T19-20 SS 815 T19-20 19-20 116,3 3,2 0,17
Thickness S 815 T21-22 SS 815 T21-22 21-22 129,3 3,2 0,20
S 815 T23-24 SS 815 T23-24 23-24 141,2 3,2 0,21
S 815 T25-26 SS 815 T25-26 25-26 153,4 3,2 0,21
da
42,9
70
Idler Wheels
for Series 812, 815, 881 M, SSR 812 Rubber Top
+ 0,4
+ 0,2
NSXT 820 T23 R... 23 142,5 25 30 35 40 40 50 0,29
NSXT 820 T25 R... 25 154,5 25 30 35 40 45 40 50 0,30
dn
d1
da
Material: polyamide (black). Max recommended tightening torque: 0,6 kgm.
Also available in Glistamide ® black
(special material). 57
Bolts and nuts in stainless steel AISI 304. 61,5
+ 0,4
+ 0,2
NXT 820 T15 R... 15 95,5 25 30 40 55 92 0,20
dn
d1
da
NXT 820 T17 R... 17 106,5 25 30 42 53 57 0,18
NXT 820 T18 R... 18 113 25 30 40 57 92 0,24
NXT 820 T19 R... 19 118 25 30 40 42 (51 * ) 57 57 0,20
L
Bore (inches)
1"
Ln
NXT 820 T19 R... 19 118 42 57 57 0,20
NXT 820 T21 R.. 21 130 11/4" 11/2" 40 (45 ) 60 61,5 0,22
NXT 820 T23 R... 23 142,5 11/4" 11/2" 40 (45 ) 59,5 61,5 0,27
NXT 820 T25 R... 25 154,5 11/4" 11/2" 40 (45 ) 59 61,5 0,30
71
Sprockets
for Series 802, 805, SSC 802 Rubber Top
20 •
– 0,1
Material: polyamide (black). Keyway: UNI 6604 - 69. See page 104.
da
72
Idler Wheels
for Series 802, 805, SSC 802 Rubber Top
+ 0,4
d1 + 0,2
NX 800 T25 R... 25 12,5 153,21 154,2 30 35 40 0,96
ø 56
da
Bolts and nuts in zinc plated steel.
89
121,5
Sprockets
for Series 512
73
Sprockets
for Series 881, 8811, 8811 TAB, SSR 812 - K 125 / 175,
SSR 812 TAB Rubber Top, SSC 8811 TAB Rubber Top
Foro (mm)
d1 – 0,1
da
• = Plain Bore. Without keyway. Keyway: UNI 6604- 69. See page 104.
Without grub screw. Tolerance d1 = + 0,3 Max recommended tightening torque : 1 kgm.
31 Material: sprocket in 0 Half-section fixing nuts (self-locking).
polyamide (black). Bolts and nuts in stainless
41,5 steel AISI 304.
da
• = Plain Bore. Without keyway. Keyway: UNI 6604- 69. See page 104.
Without grub screw. Tolerance d1 = + 0,3
31 Material: sprocket in 0
polyamide (black).
41,5
31,8
41,3
74
Idler Wheels
for Series 881, 8811, 8811 TAB, SSR 812 - K 125 / 175,
SSR 812 TAB Rubber Top, SSC 8811 TAB Rubber Top
+ 0,4
d1 + 0,2
NSX 881 T23 R... 23 11,5 141,22 142 30 35 40 51 0,44
ø 60
NSX 881 T25 R... 25 12,5 153,21 154,2 30 35 40 58,5 0,52
da
= Available upon request and minimum Max recommended tightening torque: 0,6 kgm.
order quantity. Half-section fixing nuts (self-locking).
Material : sprocket in polyamide (black). 31,8
Bolts in stainless steel AISI 304, nuts in
nickel plated brass. Ln
+ 0,4
d1 + 0,2
ø 56
Material: polyamide (black).
da
31,8
65
da
Material: polyamide (black). Also available in Max recommended tightening torque: 0,6 kgm.
Glistamide ® black (special material).
Bolts and nuts in stainless steel AISI 304. 57
61,5
da
Bore (inches)
NXT 820 T19 R... 19 118 1" 42 57 57 0,20
NXT 820 T21 R.. 21 130 11/4" 11/2" 40 (45 ) 60 61,5 0,22 L
NXT 820 T23 R... 23 142,5 11/4" 11/2" 40 (45 ) 59,5 61,5 0,27 Ln
NXT 820 T25 R... 25 154,5 11/4" 11/2" 40 (45 ) 59 61,5 0,30
75
Sprockets
for Series 820, 831, 820 Vacuum, HFP 820, XLBP 831
– 0,05
Bore (mm)
d1 – 0,1
ø 60
NS 820 T21 R... 21 10,5 129,26 129,5 25 30 35 40 45 52 51 0,46
da
NS 820 T23 R... 23 11,5 141,22 142 25 30 35 40 45 52 51 0,54
NS 820 T25 R... 25 12,5 153,21 154,2 25 30 35 40 45 54 58,5 0,63
L Bore (inch)
Important: cannot be NS 820 T21 R... 21 10,5 129,26 129,5 1" 11/4" 2" 52 51 0,46
used with chain 831 Ln
NS 820 T23 R... 23 11,5 141,22 142 1" 11/4" 2" 52 51 0,54
NS 820 T25 R... 25 12,5 153,21 154,2 1" 11/4" 2" 54 58,5 0,63
Material: sprocket in reinforced polyamide (black). Keyway: UNI 6604- 69. See page 104.
Bolts in stainless steel AISI 304, nuts in Max recommended tightening torque : 1 kgm.
nickel plated brass.
Bore (mm)
d1 – 0,1
ø 60
Ln NS 831 T21 R... 21 10,5 129,26 129,5 1" 11/4" 2" 51 0,46
NS 831 T23 R... 23 11,5 141,22 142 1" 11/4" 2" 51 0,54
NS 831 T25 R... 25 12,5 153,21 154,2 1" 11/4" 2" 58,5 0,63
Material: sprocket in reinforced polyamide (black). Keyway: UNI 6604- 69. See page 104.
Bolts in stainless steel AISI 304, nuts in Max recommended tightening torque : 1 kgm.
nickel plated brass.
20 •
d1 – 0,1
da
76
Sprockets
for Series 820, 831, 820 Vacuum, HFP 820, XLBP 831
da
B
GG 820 T25 R19 25 12,5 153,21 154 19 50 2,1
GG 820 T27 R19 27 13,5 165,21 166 19 50 2,2
GG 820 T29 R19 29 14,5 177,24 179 19 50 2,4 38
GG 820 T31 R19 31 15,5 189,27 191 19 50 2,5
GG 820 T41 R19 41 20,5 249,59 252 19 50 3,9 42,9
Idler Wheels
for Series 820, 831, 820 Vacuum, HFP 820, XLBP 831
da
Material: polyamide (black). Also available in Max recommended tightening torque: 0,6 kgm.
Glistamide ® black (special material).
Bolts and nuts in stainless steel AISI 304. 57
61,5
da
77
Sprockets
for Series 821, FLBP 821, HFP 821,
HFP 821 F, LBP 821, SLBP 821
20 •
– 0,1
Material: polyamide (black). Keyway: UNI 6604 - 69. See page 104.
d1
da
78
Idler Wheels
for Series 821, FLBP 821, HFP 821,
HFP 821 F, LBP 821, SLBP 821
+ 0,4
d1 + 0,2
NXT 821 T25 R... 25 154,7 30 35 0,75
ø 42,5
Material: polyamide (black)
da
Half-sections fixing screws in stainless steel AISI 304
153
176
79
Sprockets
for Series 879, 879 BO, 879 TAB, 880, 880 TAB, 880 TAB - K 454, 880 BO, 880 BO F, 880 BO GB,
880 GB, 880 TAB Vacuum, HFP 879 BO, HFP 880 BOT, HFP 880 TAB, LBP 879 BO, LPC 279
• = Plain Bore. Without keyway. Keyway: UNI 6604- 69. See page 104.
Without grub screw. Tolerance d1 = + 0,3
15,9 Material: polyamide (black). 0
41,5
80
Idler Wheels
for Series 879, 879 BO, 879 TAB, 880, 880 TAB, 880 TAB - K 454, 880 BO, 880 BO F, 880 BO GB,
880 GB, 880 TAB Vacuum, HFP 879 BO, HFP 880 BOT, HFP 880 TAB, LBP 879 BO, LPC 279
+ 0,4
d1 + 0,2
NSX 880 T12 R... 12 12 147,21 147,4 25 30 35 0,37
ø 60
da
Material : wheel in polyamide (black). Max recommended tightening torque: 0,6 kgm.
Bolts in stainless steel AISI 304, nuts in nickel
plated brass. 15,9
58,5
+ 0,4
d1 + 0,2
ø 56
Material: polyamide (black).
da
15,9
65
da
Material: polyamide (black). Also available in Max recommended tightening torque: 0,6 kgm.
Glistamide ® black (special material). 57
Bolts and nuts in stainless steel AISI 304.
61,5
da
Bore (inches)
NXT 820 T19 R... 9 118 1" 42 57 57 0,20
NXT 820 T21 R.. 10 130 11/4" 11/2" 40 (45 ) 60 61,5 0,22 L
NXT 820 T23 R... 11 142,5 11/4" 11/2" 40 (45 ) 59,5 61,5 0,27 Ln
NXT 820 T25 R... 12 154,5 11/4" 11/2" 40 (45 ) 59 61,5 0,30
81
Sprockets
for Series 882, 882 TAB, 882 G, HFP 882 TAB, HFP 882 TAB F, FLBP 882 TAB,
LBP 882 TAB, SLBP 882 TAB, LBP 883
Bore (mm)
d1 – 0,1
Bore (inch)
NS 882 T12 R... 12 12 147,21 149,9 1" 0,37
22,2
Material: sprocket in reinforced polyamide (black). Keyway: UNI 6604- 69. See page 104.
58,5 Bolts in stainless steel AISI 304, nuts in Max recommended tightening torque : 1 kgm.
nickel plated brass.
22
41,5
22,2
41,3
82
Idler Wheels
for Series 882, 882 TAB, 882 G, HFP 882 TAB, HFP 882 TAB F, FLBP 882 TAB,
LBP 882 TAB, SLBP 882 TAB, LBP 883
+ 0,4
d1 + 0,2
ø 60
NSX 882 T12 R... 12 12 147,21 149,9 25 30 35 40 0,37
da
Bore ( inch)
NSX 882 T12 R... 12 12 147,21 149,9 1" 0,37
22,2
Material : wheel in polyamide (black). Max recommended tightening torque: 0,6 kgm. 58,5
Bolts in stainless steel AISI 304, nuts in nickel
plated brass.
83
Sprockets
84
Sprockets
+ 0,07
d1 + 0,02
Round bore
KU 600 T06 R20 6 127 128 20 • - 74 0,36
da
dn
KU 600 T08 R20 8 165,93 177,7 20 • - 119 0,65
KU 600 T10 R35 10 205,49 219,3 35 - 161 1,30
Square bore 10
KU 600 T06 S40 6 127 128 - 40x40 74 0,36 50
KU 600 T08 S... 8 165,93 177,7 - 40x40 50x50 119 0,65
KU 600 T10 S... 10 205,49 219,3 - 40x40 50x50 161 1,30
+ 0,3
• = Plain Bore. Without keyway. Tolerance d1 = 0
Material: polyamide (black)
Keyway : UNI 6604-69. See page 104.
da
GG 600 T12 R19 12 245,36 255,2 19 95 8,2
dn
B
GG 600 T14 R19 14 285,50 296,4 19 95 9,0
8,7
50,8
17,5
63,5
85
Sprockets
for Series 1700 K, 1700 TAB K, AC 1700 K, 1701, 1701 TAB K, 1702, 1710 K, 1710 TAB K
1713 K, 1713 TAB K , 1716 K, 1790 K
ø 57
da
11,1
39
11,1
44
ZN 1700 AS
SS 1700 AS Steel Sprockets
Pitch Outside Finished
Rexnord Rexnord Dia. Dia. Bore
Order No. Order No. No of d da d1 dn Weight
Zinc plated steel Stainless steel AISI 304 Teeth mm mm mm mm kg
ZN 1700 AS T10 R20 SS 1700 AS T10 R20 10 161,8 165,1 20 69 (60*) 2,25
H7
da
ZN 1700
SS 1700 Steel Sprockets
Pitch Outside Finished
Rexnord Rexnord Dia. Dia. Bore
Order No. Order No. No of d da d1 dn Weight
Zinc plated steel Stainless steel AISI 304 Teeth mm mm mm mm kg
ZN 1700 T10 R20 SS 1700 T10 R20 10 161,8 165,1 20 69 (60*) 2,42
H7
da
86
Idler Wheels
for Series 1700 K, 1700 TAB K, AC 1700 K, 1701, 1701 TAB K, 1702, 1710 K, 1710 TAB K,
1713 K, 1713 TAB K, 1716 K, 1790 K
+ 0,3
d1 + 0,1
ø 50
Material: polyamide (white)
da
11,1
39
+ 0,3
d1 + 0,1
ø 50
Material: polyamide (white)
da
11,1
44
Sprockets
5,2
39,7
ø 51
da
24,5 15
60
87
Sprockets
da
21,4
25
0,5
for Series 35 RT
ST 35 Steel (ST) Sprockets
Pitch Outside Plain
Dia. Dia. Bore
Rexnord No of d da B Weight
Order No. Teeth mm mm mm kg
ST 35 T15 R16 15 168,34 180,7 16 0,33
ø 70
da
B
14
50
88
Drive and The use of lateral curving discs makes possible the design of
compact conveying systems with a greater number of curves.
It becoms easy to realise rings either on the same plane or
for Series 879 BO, 880 BO, 880 BO F, HFP 879 BO, HFP 880 BOT, LBP 879 BO
400
Material: plastic coated cast-iron (red) 10
da = 352
Assembly scheme
10
6
25
Drive section
Example of friction type shaft fixing.
The device is tightened to generate d1
the friction necessary to transmit drive. ø 80
ø 281
da
ø 25 h 7
ø 50
N 880 BO
Thermoplastic (N) Corner Disc NX 880 BO
Rexnord Rexnord Outside
Dia.
Order No. Order No. No of da Weight
Drive Return Teeth mm kg
N 880 BO T32 NX 880 BO T32 32 352 0,98
400
R = 222,5
24,5
22
Drive section
Example of friction type shaft fixing. 19
The device is tightened to generate Detail of the hub H7
the friction necessary to transmit drive. with hexagonal ø 50
insert
ø 86
da
60
ø 25 h 7
ø 50 H7 Return
ø 70
4
10
Return section
24,5
ø 86
3,5
with hexagonal
insert da
N° 6 self-tapping screws
ø 55
19
60
1,3
1,3
ø 23,9 ø 23,9
26
19
H7
ø 25 h7 ø 25 h 7 ø 25 bearing 25x47x8
89
Multiflex
Corner Discs
for Series1700 K, 1700 TAB K, AC 1700 K, 1710 K, 1710 TAB K
Carry Return
Closed version Open version Closed version Open version
150 150
ø 42 ø 42
ø 247 ø 247
9,25
9,25
R1 R1
1
1
R1 R1
5
5
4
4
20
20
+ 0,1
+ 0,1
+ 0,1
+ 0,1
0
0
0
0
51
34
34
34
8,75
8,75
Standard Standard
type type
1,3
1,3
1,3
1,3
ø 25 h7 ø 25 h7 ø 25 h7 ø 25 h7
TAB TAB
type ø 47 type ø 47
ø 60 ø 60
10
10
3
Components The presence of the 4 hexagonal seats permits mounting on the corner disc
a disc (for example in polyamide ) for product support.
Closed versions Open versions
43,5
6 13 N. 4 a 90 °
1
4
4
ø 8,5
5
1- External (retaining) ring, Ø 25 DIN 471 4- Internal (retaining) ring, Ø 47 DIN 472
2- Single race radial ball bearing with two 5- Seal ring with dust cover, 25X 47X 7,
sliding seals, SKF 6005 - 2RS1 DIN 3760 (NBR rubber)
(25 X47 X12) 6- Seal ring with dust cover, 25X 42X 7,
3- Bearing spacer (brass) DIN 3760 (NBR rubber)
All components are supplied separate, except the shaft bearings
which are pre-assembled
90
Multiflex
Corner Discs
for Series 1700 K, 1700 TAB K, AC 1700 K, 1710 K, 1710 TAB K
1
– 0,2
– 0,2
20
20
48,5
0
0
48
48
+ 0,2 + 0,2
ø 25 + 0,1 ø 25 + 0,1 h7
ø 25
ø 50 ø 50
Standard TAB Standard TAB
type type type type
10
10
3
– 0,2
0
48
48,5
+ 0,2
ø 25 + 0,1
ø 50
ø 25 h7
Standard TAB
type type
91
Multiflex
Corner Discs
for Series 1700 K
Carry Return
150 150
ø 247 ø 247
0,5
0,5
ø 33 ø 33
– 0,2
– 0,2
24
24
0
0
48
48
6
6
+ 0,2 + 0,2
ø 25 + 0,1 ø 25 + 0,1
ø 50 ø 50
ø 355 ø 355
R = 150 R = 150
Material: UHMWPE
176
ø 331,2
17
ø 46,7
Pin
Extractor
for Series 1700 K, 1700 TAB K, AC 1700 K, 1701, 1701 TAB K, 1702, 1710 K, 1710 TAB K
1713 K, 1713 TAB K, 1716 K, 1790 K
Rexnord Weight
Order No. kg
EP 1700 0,57
92
Compact Corner tracks range:
• Without the L straight-line sections.
• Complete with assembly holes and threaded lateral inserts (brass).
Tracks
for Series 880, 881, 882, 8811
KSU
6° a1
b1
h2
°
M8
30
h1
10° 15
r1
30 °
90
°
h4
6°
28 ø 8,2
L
6°
a2 = a1 + e
e
°
30
L
r2
30 °
r1
90
°
6°
L
Single Strand = 1
Double Strand = 2
Triple Strand = 3
etc.
93
Corner tracks range:
• Without the L straight-line sections.
• Complete with assembly holes and threaded lateral inserts (brass).
Compact
• Single or multiple strand.
Corner
Tracks
for Series 879 TAB, 880 TAB, 880 TAB- K 454,
HFP 880 TAB, SSC 8811TAB RubberTop, 8811TAB, 882 TAB,
HFP 882 TAB, HFP 882 TAB F, RR 882, 1873, 1874, 4874
KTU 6°
a1
°
b2
30
b1 L
h3
h2
h1
30 °
r1
ø 8,2
°
M8
90
6°
15
L
6°
°
30
a2 = a1 + e
e L
30 °
r2
r1
°
90
6°
L
Material : polyethylene PE with
Chain Radius Width ± 0.5 Pitch
molecular density 1.000.000 Rexnord width r1 a1 b1 b2 h1 h2
L h3 e
( UHMWPE ). Order No. Used for Chain Type mm mm mm mm mm mm mm mm mm mm
Colour : black. 879 TAB-K325
KTU 013 500... 880 TAB-K325 K 82,5 500 100 45 70 25 18 9,5 – 90
State of supply : the corner tracks are 8811TAB -K325
supplied complete with carry and 879 TAB-K450
return sections. 880 TAB-K450
KTU 018 610... K 114,3 610 125 45 70 25 18 9,5 – 120
880 TAB-K454
* = Supplied without the L straight-line 8811TAB -K450
sections.
KTU 030 610... 8811TAB -K750 K 190,5 610 200 45 70 25 18 9,5 – 195
Special dimensions on application.
KTU 218 610... 882 TAB-K450 K 114,3 610 125 60 90 32 26 16 – 120
When ordering indicate the number of
strands required: KTU 230 610... 882 TAB-K750 K 190,5 610 200 60 90 32 26 16 – 195
KTU 240 610... 882 TAB-K1000 K 254 610 265 60 90 32 26 16 – 260
... KTU 248 610... 882 TAB-K1200 K 304,8 610 320 60 90 32 26 16 – 310
Order No. : see above table 1873-K325
KTU 313 500... 1874-K325 K 82,5 500 100 – 90
4874-K325
Single Strand = 1 KTU 318 500... 1873-K450 –
K 114,3 500 125 120
1874-K450
Double Strand = 2
1873-K600
Triple Strand = 3 KTU 324 610... 1874-K600 K 152,4 610 160 34,6 70 36 29 19 – 160
etc. 4874-K600
1874-K750 –
KTU 330 610... 4874-K750 K 190,5 610 200 195
94
Magnetic The Rexnord magnetic corner concept combines simplicity, with
high performance.
Strong permanent magnets provide increased magnetic hold-down
Corner force.
Tracks
for Series 881 M
KMU
a1
b1
L
h1
r1
90
7,5° 15 °
h2
54
L
a2 = a1 + e
e
L
r2
90
7,5 ° 15 °
° r1
L
Single Strand = 1
Double Strand = 2
Triple Strand = 3
etc.
95
Compact
Corner
Tracks
for Series LPC 279
KLPC
a2 = a1 + e
a1 e
h1
r2
r1
h2
°
90
26,4
10
96
Compact
Straight
Tracks
for Series 880, 881, 8811
SSU - SSU/P
a1 a1
2000
a1
b1
h2
a1
h1
h4
10 °
for Series 879 BO, 879 TAB, 880 TAB, 880 B0, 880 TAB- K 454, HFP 880 TAB, HFP 879 BO,
HFP 880 BOT, LBP 879 BO, 8811TAB, SSC 8811TAB RubberTop, 882 TAB, HFP 882 TAB,
HFP 882 TAB F, RR 882 STU
a1
b1
2000
h3
h2
h1
b2
a1
97
Corner tracks range:
• Complete with assembly holes and threaded lateral inserts (brass).
• Single or multiple strand.
Compact
Corner
Tracks
for Series LBP 882 TAB, SLBP 882 TAB,
FLBP 882 TAB, LBP 883
KTU a1
6°
b2
°
b1
30
h3
h2
h1
ø 8,2
30 °
r1
M8
°
90
6°
15
6°
°
a2 = a1 + e
30
e
30 °
r2
r1
°
90
6°
Material : polyethylene PE with Chain Radius Width ± 0.5 Pitch
molecular density 1.000.000 Rexnord width r1 a1 b1 b2 h1 h2 h3 e
( UHMWPE ). Order No. Used for Chain Type mm mm mm mm mm mm mm mm mm
Colour : black. LBP 882 TAB - K 375
KTU 215 670... SLBP 882 TAB - K 375 K 95,2 670 125 58 85 32 26 16 100
State of supply : the corner tracks are FLBP 882 TAB - K 375
supplied complete with carry and
KTU 218 610... LBP 883 TAB - K 450 K 114,3 610 125 58 90 32 26 16 120
return sections.
Special dimensions on application. LBP 883 TAB - K 750
KTU 230 610... SLBP 882 TAB - K 750 K 190,5 610 200 58 90 32 26 16 195
Single Strand = 1
Double Strand = 2
Triple Strand = 3
etc.
98
Compact
Straight
Tracks
for Series LBP 882 TAB, SLBP 882 TAB,
FLBP 882 TAB, LBP 883
STU
a1
b1
h3
2000
h2
h1
b2
a1
99
Corner tracks range:
• With the L straight-line sections.
• Without assembly holes or threaded lateral inserts (supplied on
Compact
request).
• Single strand. Corner
Tracks
for Series 1700 TAB K, 1701 TAB K, 1710 TAB K,
1713 TAB K
KTU/S
a1
b2
b1
h3
h2
L
h1
°
r1 90
L
Corner tracks for Series 1700TAB K, 1701TAB K, 1710 TABK, 1713TAB K
Material : polyethylene PE with Chain Radius Width
molecular density 1.000.000 Rexnord Used for width r1 a1 b1 b2 h1 h2 h3 L
( UHMWPE ). Order No. Chain Type mm mm mm mm mm mm mm mm mm
Colour : black. KTU508 250 S 1700TABK 250 100
1701TABK 55 58 70 40 21 12 50
State of supply : the corner tracks are KTU508 500 S 500 100
supplied complete with carry and KTU515 250 S 250 110
return sections. 1710TABK 98 58 70 40 31 22 50
KTU515 500 S 500 110
Special dimensions on application.
KTU540 500 S 1713TABK 253 500 270 58 70 40 30,5 20 50
Compact
Straight
Tracks
for Series 1700 TAB K, 1701 TAB K, 1710 TAB K,
1713 TAB K
STU a1
a1
b2
2000
b1
h3
h2
h1
100
Numerical
Index
101
Resistance
against
chemical
agents
HP TM
OPTI-Plus ® LF ® POLYPROPYLENE POLYAMIDE POLYETHYLENE
AISI 430 AISI 304 ACETAL D PP PA PE
CHEMICAL AGENT Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C
102
Resistance
against
chemical
agents
HP TM
OPTI-Plus ® LF ® POLYPROPYLENE POLYAMIDE POLYETHYLENE
AISI 430 AISI 304 ACETAL D PP PA PE
CHEMICAL AGENT Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C Conc.% 23° C
MUSTARD + + – +
NITRIC ACID 10 / 10 + 5 – + 10 – 5 /
OLEIC ACID 100 / 100 / – + 100 + /
PARAFFIN + + + 100 / + +
PETROLEUM + + + 100 / + –
PETROLEUM ETHER + + + + +
PHENOL 10 + + –
PHOSFORIC ACID 10 – 10 – 10 – 85 + 10 – 95 +
POTASSIUM HYDROXIDE 50 + 10 +
SEA WATER – + / + + +
SILICONE OIL + +
SILVER NITRATE 60 / 20 + +
SOAP AND WATER + + + + + +
SODIUM CARBONATE 5 + 5 + + Sat. + 10 + +
SODIUM CHLORIDE 5 / 5 + + Sat. + 10 + +
SODIUM HYDROXIDE – 10 + 30 + 10 + +
SODIUM HYPOCHLORITE – – – 20 + + +
SODIUM SILICATE 100 + +
SODIUM SULPHATE 5 + 5 + + Sat. + 10 + +
SOFT DRINKS + + + + + +
SUDS + +
SULPHURIC ACID 10 – 10 – 40 – 98 + 10 – 40 /
TARTARIC ACID 10 + 10 + 30 / 10 + + +
TETRALINE – +
TINCTURE OF IODINE + + – +
TRANSFORMER OIL / +
TRICHLORETHYLENE + + – / / +
TURPENTINE + + – – / –
VASELINE + + + /
VEGETABLE JUICES + + + + + +
VEGETABLE OILS + + + + + +
VINEGAR + + + + + +
WHISKY / + + + + +
WINE + + + + + +
XILOL + + + – + /
ZINC CHLORIDE 10 – 20 + 10 /
103
Keyway
Dimensions
30 8 + 0,036 33,3
0
35 10 38,3
+ 0,2
40 12 43,3
0
d1 45 14 + 0,043 48,8
50 14 0 53,8
60 18 64,4
104
Rexnord –
Partners in Industry
LF
R
WRB OPTI-Plus ® HP TM
®
Acetal Low Friction Wear resistant resin ® Special-Alloy Stainless Steel High Performance
Rex LF ® is a mixture of acetal based resins. To be used in abrasive environments (casting, In collaboration with the steel industry, Longer sliding wear life, reduced chain
Improves mechanical characteristics and machined steel components, sand, glass, Rexnord has developed a special heat treated elongation, lowest available friction. The
sugar). alloy of chrome steel with nickel. This results continuous search of Rexnord for
Chains
guarantees longer life in heavy duty
conditions (heavy products, long distances It offers a wear life 5 times longer than acetal in excellent strength properties, as well as improvement of their product has resulted in
and high operating speed). resin. improved corrosion-resistance. the development of a new, patentd, material:
Operating temperatures: The most outstanding properties of Rex-OPTI- Rex HP ™ High Performance.
The mechanical characteristics are similar to
in air ( - 40°C a + 80°C ) SALES OFFICES: Plus ® are its high resistance to wear, its This new material has the lowest coefficient of
those of acetal resin.
in hot water ( + 65°C ) ground finish, and 40% higher strength. friction, available on the market.
The chain is not suitable to be used in wet Austria - Wien
This material is especially suitable for
Inflammability: 94 HB. environments (can swell). Must use oil Denmark - Copenhagen In addition no "break in" is required thus
applications, where external lubrification is not
Colour: LF ( brown ), WLF ( white). lubricants. France - Paris-Lyon insuring maximum performance from startup.
possible.
Operating temperatures: Germany - Betzdorf (with distribution centre) Rex-OPTI-Plus ® is the preferred choice for
Operating temperature of Rex HP ™ material:
PRODUCT RANGE in air (- 5°C a + 100°C ) - Düsseldorf -Siegen-Stuttgart new or replacement installations.
in air ( - 40 to + 80 °C ) PRODUCT RANGE
Italy - Correggio (with distribution centre)
AS Inflammability: 94 HB. in hot water ( + 65 °C )
Netherlands - ‘s-Gravenzande (with distribution centre)
Colour: black. Colour: dark grey.
United Kingdom - Warrington
Conductive resin Canada - Edmonton-Montreal-Toronto-Vancouver
Load carrying capacity
United States - Atlanta (GA)-Columbus (OH)
Good electrical conductivity. - Dallas (TX)-Fresno (CA)-Grafton (WI) Longer sliding wear life *
Reduces the accumulation of electrostatic PC Mexico - Cordoba-Guadalajara
AISI 430 AISI 304 Rex-OPTI-Plus ®
Ultimate strength N
Lower mechanical characteristics.
Australia - Melbourne-Sydney
Flight wear
14000 Rex LF ®
Load carrying capacity is 40 % lower than Highly resistant to impact and to high Singapore - Singapore
Rex LF.® temperatures. 10000 Rex HP ™
China - Shangai
Lubrication system is recommended for Maintains its rigidity and other mechanical
7600
Chain elongation
( hinge wear )
WPP
elongation
Rex LF ®
% pitch
Rex
-OPTI-Plus ®
Reinforced polypropylene Rex HP ™
Coefficient of friction
Certification FDA & USDA 0,30
Rexnord Marbett S.p.A. RMCC Nederland 0,26
Italy P.O. Box 112
0,22
FDA USDA Via della Costituzione, 45 2690 AC ‘s-Gravenzande
0,18
42015 Correggio (RE) The Netherlands
American institute (Food and Drug United States Department of Agriculture, Tel. 0522 - 639333 Phone 0174 - 445111 0,14
Administration), responsible for the cerfification responsible for the approval of components and Fax 0522 - 637778 Fax 0174 - 445222 0,10
Metal Glass Plastic Paper
of materials to be in contact with food. machinery in the meat, poultry and dairy
E-mail vendite.italia@rexnordmarbett.it E-mail mcc@euronet.nl Product material
For direct contact with food the following industries.
materials have been approved: The following chains have been approved :
• AISI 304 843, 845, 963, 879, 879 TAB, 880, 880 TAB, * = dry
Graph shows comparative results at high-speed,
• HP,TM
WLF
R
882 TAB, 1843, 1873, 2873, 3873, 1700, 1701, operation.
1702. Bulletin No. 02063