Professional Documents
Culture Documents
PRODUCT INFORMATION
Composition Epoxy, waterborne and polyamine curative
Packaging 1.0 L (~1.03 kg) unit 0.8 L component A
0.2 L component B
5.0 L (~5.16 kg) unit 4 L component A
1 L component B
15.0 L (~15.54 kg) unit 12 L component A
3 L component B
1/3
Density ~1.03 kg/l (23 °C) (EN ISO 2811-1)
APPLICATION INFORMATION
Mixing Ratio Component A : Component B = 4 : 1 (by volume)
Consumption Apply in one to two coats, with a consumption of 0.10 kg/m2 approxim-
ately per coat depending upon surface roughness and absorption.
Note: For metal substrates apply 1 x Sikalastic® Metal Primer (0.20 kg/m2
approximately) instead of Sika® Bonding Primer (please refer to Sikalastic®
Metal Primer Product Data Sheet for further information).
These figures are theoretical and do not include for any additional material
required due to surface porosity, surface profile, variations in level and
wastage.
Ambient Air Temperature +5 °C min. / +40 °C max.
Relative Air Humidity 80 % r.h. max.
Dew Point Beware of condensation.
The substrate and uncured coating must be ≥ 3 °C above dew point.
Substrate Temperature +5 °C min. / +40 °C max.
Substrate Moisture Content Visible damp free (maximum 18 % wood moisture equivalent)
≤ 6 % pbw moisture content Test method: Sika®-Tramex meter
≤ 4 % CM - measurement or Oven-dry-method
No rising moisture according to ASTM (Polyethylene-sheet)
Waiting Time / Overcoating Before applying any recommended SikaRoof® MTC, Sikalastic® and Sika-
floor® products on Sika® Bonding Primer, allow:
Substrate temperature Minimum waiting time Maximum waiting
time
+10 °C ~4 h 7d
+20 °C ~2.5 – 3.5 h 7d
+30 °C ~1 h 7d
2/3
APPLICATION LOCAL RESTRICTIONS
Prepare Sika® Bonding Primer by adding component B Note that as a result of specific local regulations the
into component A container, mix with an electric drill declared data and recommended uses for this product
until a homogeneous light green colour is achieved may vary from country to country. Consult the local
and the product is free of streaks. The 1 L packaging Product Data Sheet for the exact product data and
can be mixed by spatula or flat stick. uses.
Sika® Bonding Primer can be applied by short-piled
roller, brush or airless spray.
Allow primer to dry sufficiently (see table waiting time ECOLOGY, HEALTH AND SAFETY
/ overcoating) before overcoating. For information and advice on the safe handling, stor-
CLEANING OF EQUIPMENT age and disposal of chemical products, users shall refer
to the most recent Safety Data Sheet (SDS) containing
Clean all tools and application equipment with water physical, ecological, toxicological and other safety-re-
immediately after use. Hardened and/or cured materi- lated data.
al can only be removed mechanically.
LEGAL NOTES
IMPORTANT CONSIDERATIONS The information, and, in particular, the recommenda-
▪ Do not apply Sika® Bonding Primer on substrates tions relating to the application and end-use of Sika
with rising moisture. products, are given in good faith based on Sika's cur-
▪ Sika® Bonding Primer is not recommended for use as rent knowledge and experience of the products when
a direct primer for Sikagard® 307, Sikagard® 317 and properly stored, handled and applied under normal
Sikalastic®-641 conditions in accordance with Sika's recommenda-
▪ Always ensure good ventilation when using Sika® tions. In practice, the differences in materials, sub-
Bonding Primer in a confined space, to ensure drying strates and actual site conditions are such that no war-
and full curing. ranty in respect of merchantability or of fitness for a
▪ If the primer is damaged by rain, a chalky surface will particular purpose, nor any liability arising out of any
result and the surface must be re-primed. legal relationship whatsoever, can be inferred either
▪ The incorrect assessment and treatment of cracks from this information, or from any written recom-
may lead to a reduced service life and reflective mendations, or from any other advice offered. The
cracking (for further information please contact Sika user of the product must test the product’s suitability
Technical Department). for the intended application and purpose. Sika re-
▪ If heating is required do not use gas, oil, paraffin or serves the right to change the properties of its
other fossil fuel heaters, these produce large quantit- products. The proprietary rights of third parties must
ies of both CO2 and H2O water vapour, which may be observed. All orders are accepted subject to our
adversely affect the finish. For heating use only elec- current terms of sale and delivery. Users must always
tric powered warm air blower systems. refer to the most recent issue of the local Product Data
▪ New concrete should be allowed to cure/hydrate for Sheet for the product concerned, copies of which will
a minimum of 10 days, preferably 28 days. be supplied on request.
SikaBondingPrimer-en-AE-(08-2017)-2-1.pdf
3/3