Professional Documents
Culture Documents
Owner’s Engineer
Contractor
Sub-Supplier
Project
Title
Packing Procedure
CONTENTS
Rev.0 3 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
1. Scope
This Procedure is intended to specify the requirements of packing, marking and handling of the items for
VUNG ANG 2 THERMAL POWER PLANT PROJECT.
2. Purpose
The purpose of this instruction is to provide the method of packing, marking and handling to protect from any
corrosion, contamination, physical damage or any effect which could lower the quality or cause deteriorate during
shipment, handling and storage.
3. Reference Document
4. Preservation
4.1. The inspection for paint shall be performed before packing the items.
4.2. All surfaces of products shall be cleaned free of oil, rust and contaminant before packing.
4.3. Sufficient amount of the grease shall be applied to all of threaded areas.
4.4. All machined surfaces shall be applied Tectyl 506 or equivalents to prevent rust.
4.5. The bagged V.C.I(Volatile Corrosion Inhibitor) in the net shape bad shall be hung or powdered V.C.I shall be scattered
inside of the Carbon Steel Tank, Vessel, Drum, Heat Exchanger, Tube and Pipe Spool, etc. which the inside of the
product has no protection from painting or corrosion inhibitor after finishing cleaning inspection. The amount of V.C.I is
min. 30g/㎥.
(Insertion of V.C.I can be excluded in which the product is filled with Nitrogen.)
4.6. After assembling the man-way, attach a sticker giving information about the quantity of V.C.I used in the tank at a
visible spot near the man-way cover.
4.7. For inside of carbon steel pipe V.C.I shall be applied, and for inside of stainless steel pipe desiccant(Min. 300g/㎥) shall
be applied.
4.8. Remove all V.C.I before installation(or construction) and replace the new V.C.I every 6 months if the storage period
goes over than 6 months.
4.9. Bagged desiccants will be put inside of the boxes to protect from corrosion during shipment and temporary storage
before erection. The amount of desiccant is min. 300g/㎥.
(Desiccant can’t contact with products directly.)
Rev.0 4 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
※ Caution : Desiccant should be applied inside of the barrier(Vinyl, V.C.I Film, Al-Foil, etc.) that covering the product,
and no material that includes moisture as wood shall be placed inside of barrier.
5. Packing
Rev.0 5 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.1.3. Skid
Skids shall be applied to products that are strong enough to endure water, sunshine and damage due to contact or
shock when handling products directly.
5.1.4. Bundle
Bundles shall be applied to products that are simple and strong enough to endure damages due to contact or shock
when loading or unloading.
Rev.0 6 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
☞ Bagged desiccants shall be put inside of the Al-foil. The amount of desiccant is over 300g/㎥.
5.1.6. Pallet
Pallets shall be applied to products such as thin plates or pipes that are not strong enough to protect products by
simple skids or bundles during the transportation and storage which can effect deformation of product. And special
cares are needed to prevent damage when stacking the product.
Rev.0 7 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
CE, DE
5.1.8. Drum
Drum shall be applied to products such as cable that are thin and long length.
5.1.9. Container
Container packing shall be applied to products that need water proofing and damage prevention from shock and
pressure. Usually, shipping container will be used for this packing type, and these packing types shall be used
before installation at site.
Rev.0 8 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.2. General
5.2.1. The size of Knots must not exceed 1/3th the width of timbers.
5.2.2. The wood packing materials used in packing or shipment for Export PJT must be either heat treated or be fumigated
according to ISPM-15.(the wood packing materials for country that are not requested to apply ISPM-15 can be excluded)
- Heat treatment with minimum56℃ in core temperature for more than 30 minutes.
- Fumigation with MB(Methyl Bromide) gas treatment.
5.2.3. The plywood that satisfies standard/semi-waterproof/1st grade in KS F3101 should be used.
In case of imported plywood, plywood that satisfies BB/CC grade in IHPA or equivalent level should be used.
[The thickness of plywood shall satisfy standard(±4%) of KS, and 9T plywood can be allowed not less than 8.5T,
12T plywood can be allowed not less than 11.5T]
5.2.4. All wood shall not have the direct contact with products. The product surfaces directly contacting wood should be
protected by placing a cushioning material(Toilon or Rubber pad). However, rubber pads shall not contact with products
directly.
5.2.5. All packing materials should maintain its function even if those materials are stored for maximum 12 months at outdoors.
(However, in case of packing for product that required storage of less than 12 months, packing material which
maintain its function during storage period can be applied.
5.2.6. Products shall be packed separately to stack according to their weight and bulk.
5.2.7. The Tags shall be attached to each products to make field identification easy, and the tags shall be adhered firmly to
prevent being detached easily during handling and transportation.
5.2.8. Stainless steel materials and equipment shall be packed separately from carbon steel materials.
5.2.9. Small loose items and spare parts shall be packed separately.
5.2.10. Small loose items(all items under 1m) shall be packed in boxes.
5.2.11. The Products shall be properly blocked and braced to prevent damage during transportation, handling and storage.
5.2.13. In case of fixing product with Steel bands, the pad(plastic, Toilon, Film, etc.) shall be applied to prevent the direct
contact from the product.
5.2.14. The rubber pad, plastic guard, etc. shall be placed between Cord Strap and the sharp part of product in order to protect
from damage.
Rev.0 9 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.2.15. To prevent damage of painted surfaces due to direct contact between products, cushioning materials shall be put between
the products and be fixed.
5.2.16. Thin products which have risk of deformation caused by direct contact with handling equipment(Wire, Fork, etc.) shall
be packed in wooden boxes or steel frame.
Open Crate
Steel Frame
5.2.17. The specification of tent used for the top of wooden box or covering products shall be applied as follow.
- Specification : PE Tarpaulin(Min. 200g/㎡), PVC Tarpaulin(Min. 500g/㎡), Allowable range : -5%
- Caution: unit area of tent in circulation on the market is 1.8 ㎡(Min. 360g/1.8 ㎡)
5.2.18. Products with galvanizing shall be required to have protection with tent or vinyl according to its shape and packing type.
- Skid/Bundle/Pallet : All sides(including bottom side) covering with tent is required for the product with shape that
water could be stagnating
(However, covering with tent shall not be applied for the product with shape that water could not be stagnating.)
- Wooden Box : All sides(including bottom side) covering of product with vinyl is required inside of the box.
5.2.19. In case of wooden box, pallet, skid and so on, timber and timber shall be assembled with bolts or nail, and timber which
are more than 90x90mm shall be assembled with bolts according to below table.
1) Bottom of Wooden Box/Pallet
Division Thickness Assembly method
Header
≥ 90mm with bolts(Min.12mm)
머리목
≤ 60mm with nails
Lifting point with bolts(Min.12mm)
Load Bearing Floor Member ≤ 90mm One half : with bolts(Min.12mm)
Except for Lifting Point
부하목 The others : with nails
90mm < T ≤ 150mm with bolts(Min.12mm)
> 150mm with bolts(Min.16mm)
※ If load bearing floor member is 90x90mm, screws can be used instead of bolts(quantity : 2 ea/point)
2) In case of skid, Min. 12mm bolts shall be applied for assembly between the timbers(more than 90x90mm) normally.
(But, Min. 16mm bolts shall be applied for timbers which are more than 150x150mm)
Rev.0 10 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.2.20. The flanged/non-flanged opening parts of product, pipe, tube, etc. shall be covered with plastic cap or plywood, and
sealed using adhesive tape that are low in halogen and sulfur.
1) Flanged opening
- The flange faces shall be covered with plywood that have the minimum thickness of 9mm or steel cover, and 3 mm
rubber gasket or Toilon shall be inserted in order to seal. The quantity of bolts shall be at least 4 points
- Additionally, flanged opening part(including pipe part) shall be covered with vinyl and tent, and sealed using adhesive
tape. However, in case of flange faces is covered with steel plate or product is packed in wooden box, covering with
vinyl and tent can be excluded.
2) Non-flanged opening
- The non-flanged openings shall be covered with plywood or plastic cap or plastic sheet, and sealed using adhesive tape.
In case of using plywood or plastic sheet, opening part should be sealed as much as possible with vinyl.
[Flanged opening]
Tape
Plywood
Vinyl
Tent
[Non-flanged opening]
Tape Tape
5.2.21. One copy of packing list shall be put in the vinyl bag and be attached by using steel covers to the outside of packages.
(In case of box, on copy of packing list shall be put in the box if additional required.)
5.2.22. In case of transportation with dry container, the timber direction of rubbing strip of box/pallet/skid shall be applied in the
same direction as the longitudinal direction of the container.
Rev.0 11 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.2.23. Products(Paint/Thinner, Battery, etc.) which are classified as dangerous goods should be packed according to the related
international regulation such as IMDG Code(International Maritime Dangerous Goods Code), TI(Technical Instructions
for the safe transport of dangerous goods by air) and so on.
5.3. General requirements for Moisture Proof Box, Water Proof Box and Open Crate
5.3.1. All boxes should be designed according to‘AppendixⅠ, Ⅱ’of this document.
5.3.2. In case of wooden boxes, all the products shall be covered fully with barrier(Vinyl, V.C.I Film, Al-Foil, etc.) to make the
most of the prevention of the product from the moisture that could be flowed into from the outside and could be created
inside of the box.
5.3.3. If lots of products are piled up in the boxes, products should be fixed tightly with plywood or wood pieces to prevent
physical damage from rolling caused by moving or transportation.
5.3.4. The empty space caused by unevenness of products in the boxes should be filled up with wood pieces in order to prevent
the breakage caused by stacking during ocean transportation.
Wrong Correct
5.3.5. All boxes shall be packed which is able to pile up with several layers in the holds of vessels when shipping or
transportation.
Correct
Wrong
Rev.0 12 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.3.6. All wooden boxes for export shall be tightly wrapped and fastened with steel straps or cord straps according to below a
table. (For the domestic box, this clause shall be applied to the project with additional request from customer.)
5.3.7. The wooden boxes shall be covered with tent(PE Tarpaulin) to prevent from weather effects such as rain during
transportation and storage.
Only with specific need, PVC Tarpaulin shall be applied.
※ Process : After assembling top plate of box, install a corner protector at upper corner, and its top should be covered
with vinyl and tent. And the edge of tent’s hem shall be fixed with webbing belt.
5.4.1. For product packed in wooden skid or bundle, the timber which can have at least 120 mm of the minimum distance
between bottom of product and ground shall be used for packing. However, for products are handled only by crane, the
timber which can have at least 90 mm can be used.
※ For boiler pressure part(Header, Tube, Panel), the minimum thickness of lower timber shall be
150 mm or more.
5.4.2. The distance between wooden skids shall maintain the regular interval to make loading easy while shipment.
5.4.3. In case of wooden skids the timber for skid shall be fixed tightly to the products with bolts, wire ropes, etc. to prevent
escaping of timber during transportation and handling.
5.4.4. The interval between bolts for fixing wooden skid and products should be maintained at least 30 cm or more.
Rev.0 13 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.4.5. The minimum size of the bolts is 12 mm, but 16 mm bolts should be applied if the weight of packing is more than 10 ton
or height of packing is more than 1m.
5.4.6. Products that are packed in group with more than 2 shall not exceed 1.5 m in height and 15 ton in weight.
5.4.7. The timber should be installed within at least 500mm from the both edges of products.
5.4.8. When products are packed in bundle by multi-stacking, struts(role of skid) between products shall be aligned vertically
and be tightened with bolts entirely to prevent separation. For products that can be moved during the shipping or
handling, each stage shall be fixed with Cord Strap or Steel band, and struts should be applied between each stages.
When assembling, coated(galvanized or equivalent) bolts, nuts and washer shall be used and surface of the bolts shall be
protected by using the rubber hose, etc..
Wrong Correct
Add Strut
Fix Bolt hole
5.4.9. The bolts used in upper part of wooden skid/bundle/pallet shall be fastened after grooving to avoid interference during
transportation or shipment. However, in case of local transportation or not stacking during storage, wood grooving can
be excluded.
Wrong Correct
Wrong(불량)
Correct(양호)
5.4.10. In case of packing in bundle or pallet, the interval between Cord straps or Steel bands should be below 2 m.
5.4.11. Check if there is no loosen bolts, cord strap, steel band due to the wood drying after packing completion and before
shipment. All bolts and nuts should be fastened tightly.
Rev.0 14 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.4.12. All products shall be packed properly with timber, plywood and rubber pad, etc. to prevent damage caused by direct
contact with handling equipment during handling.
(Especially, handling points of products as Vessel, Tank, Big bore pipe, etc. packed in skid shall be protected with timber,
rubber pad, plastic, etc.)
5.4.13. Products packed in the Skid/Bundle/Pallet which are vulnerable to weather effects or dust during transportation and
storage shall be covered with tent to prevent.
5.4.14. Stainless steel products(non-painted) which are vulnerable to seawater or water contaminants shall be covered with tent
when packed in the Skid/Bundle/Pallet.
Caution : Direct contact with packing materials that includes chlorine contents(PVC Tarpaulin, etc.) shall be avoided.
5.4.15. Products(PVC Pipe, etc.) which are vulnerable to ultraviolet rays shall be covered with tent when packed in the
Skid/Bundle/Pallet.
5.4.16. Products that are covered by tents shall be tied firmly by P.E ropes, cord strap, etc. to avoid being torn during
transportation. And the rubber pad, Plastic Form, additional Tent, etc. shall be placed between tent and sharp part of
product in order to protect tent from damage.
Rev.0 15 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.4.17. Sling point of Products weighed more than 3 Ton packed in pallet shall be protected with the wire cover lower. The
specification for wire cover lower refer to the specification of the wooden box(Appendix.Ⅱ).
5.4.18. The pallet exceeding 1 tons will be designed according to ‘table 1, 3, 4’ of ‘Appendix II’ in this document.
5.5.1. In case of steel framed skid, uneven parts should be covered or leveled with nylon ropes or plywood before covering it
with tents in order to prevent product’s damages caused by rain water pools on tent’s top during transportation and
storage at sites. And extra lifting lugs for handling should be installed to prevent damages of tents or products caused by
wire ropes when handling products.
Lifting Lug
Plywood
Rev.0 16 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.6. Packing for Steam Drum
5.6.1. Internal materials(applied short term rust prevented) which are loose part should be packed in the moisture proof packing,
and timbers and packing materials which contain moisture shall not be packed together in the moisture proof packing.
Packing sketch for steam drum(For Reference)
5.7.1. The timbers should be installed at every interval of 1.5 ~ 2 m.(Column : Max. 3 m).
5.7.2. Apply the plywood (min. 9 mm) to the bottom of the base plate such as columns to prevent damage.
5.7.3. Add the plastic guards to the contacting surface between metal and metal, and then execute the banding work.
5.7.4. Pack the members including brackets at both ends in separated packing horizontally, and complement product using the
struts.
5.7.5. Big sized members and small sized members shall be packed separately. If they are packed together, pack them stably
with members having small difference in the size and tighten with Cord Straps or Steel Band.
5.7.6. In case of pipe braces, gusset plates that are delivered as assembled form shall be disassembled and packed separately in
boxes for efficiency of packing. In this case, marking of member’s number and lists of member should be written
thoroughly.
Rev.0 17 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
[FIG 1] Wooden Bundle (Bolt Type)------ Apply to Ocean transportation
※ Steel Band(Min. 19mm) can be used instead of Cord Strap(Min. 25mm). In case of using the steel band, steel band cannot
contact with product directly.
Rev.0 18 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
[FIG 2] Wooden Bundle (Cord Strap Type)------ Apply to local transportation
※ Steel Band(Min. 19mm) can be used instead of Cord Strap(Min. 25mm). In case of using the steel band, steel band cannot
contact with product directly.
Rev.0 19 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.8. Packing for items of Condenser
5.8.1. The opened part of Shell & Hotwell shall be covered with plywood, and then upper part of them shall be covered with
plastic sheets in order to protect from the foreign materials entering to inside of products. The Toilon shall be placed
between tube sheet faces and plywood for protection to prevent damages when packing Shell.
Timber
Plywood
plastic
sheet
5.8.2. The upper aspect of the Extended Neck and Transition shall be covered with plastic sheets in order to protect from the
foreign materials entering to inside of products.
[Transition] [Neck]
5.8.3. Items of Condenser(Miscellaneous components such as spray pipe, pad, plate & coupling etc,) shall be transported safely
by choosing the most reasonable type among the boxes, bundles and skids according to their shape and specification.
5.9.1. Panel type ducts shall be packed in pallet. However, products which is assembled and supplied as assembly type or steel
structure such as beam can be packed in the skid.
Rev.0 20 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
[FIG. 3] Panel Type (1) ------ Packing Style (Pallet)
※ Steel Band(Min. 19mm) can be used instead of Cord Strap(Min. 25mm). In case of using the steel band, steel band cannot
contact with product directly.
Rev.0 21 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
※ Steel Band(Min. 19mm) can be used instead of Cord Strap(Min. 25mm). In case of using the steel band, steel band cannot
contact with product directly.
Rev.0 22 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Rev.0 23 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
5.10. Packing for Coal Burner
5.10.1. Coal burner & O.F.A shall be packed in steel shipping frame which is able to pile up with several layer in hold of vessel,
when shipping for transportation.
SAMPLE
5.11.1. Susceptible parts such as gauges shall be wrapped in vinyl and Toilon to prevent damage.
5.11.2. Motors and valves shall be wrapped in polyethylene film and fixed with tapes.
5.11.3. Systems packed in skid type shall be covered with plastic sheets or shrink wrap film in order to protect from the foreign
materials entering to inside.
Rev.0 24 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
6. Marking
6.1. All packages shall have clear shipping mark. The size of letters shall be normally 2.5 cm or bigger. If impossible, the
letter size will be determined by size of packages. The shipping mark is as follows.
6.2. The shipping mark shall be stenciled on the product directly, or be attached after printing and coating A4 or A3 paper to
the product, or pasted waterproofing sticker on the products.
In case of coating, coating paper shall have enough space(Min. 1 cm) for stapling that the staple does not go through the
paper.
Rev.0 25 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
6.3. The appropriate instruction for handling, transportation and storage shall be marked on outside of the package using
stencil.
6.4. Care marks should be marked using a red-waterproofing stencil. If the background color is black or dark color, the
contrasting color for marks shall be applied.
6.5. The content of shipping marks should be recorded accurately in order to avoid the difficulty of identifying material at the
site(INV.NO, PKG NO, DIMENSION, PKG Q’TY etc.).
6.6. When the shipping marks are manufactured with plywood, management items should be recorded with black oil-based
pen or paint.
6.7. When using the coating films, four edges of the shipping marks shall be fixed with tapes after being punched by a stapler.
If necessary, its top can be fixed with tapes additionally.
6.8. When skids are fixed with cord straps or steel bands, shipping mark can be fixed with cord straps or steel bands used.
6.9. If it’s hard to attach the coating films to products such as steel structures, a sticker should be used and four edges of the
shipping marks shall be fixed with tapes.
6.10. Stencil or sticker shall be used for marking of care marks and warning marks.
6.12. C.O.G(Center of Gravity) mark shall be marked clearly on all items and outside of packing.
- The weight of product is less than 20 Ton : 2 Point(Front/Back side for handling)
- The weight of product is more than 20 Ton : 4 Point
- For the product which C.O.G is not center : 4 Point(regardless of weight)
7. Shipping
7.1. General
7.1.1. Every handling tools or equipment shall be checked for their capability before using.
7.1.2. The experienced or trained person should be assigned to the working that need special handling or lifting equipment.
7.2. Handling
7.2.1. Followings shall be considered when handling with devices and equipment.
1) Product’s characteristics such as size, weight and center of gravity.
2) Handling types such as lifting, turning and positioning.
Rev.0 26 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
7.2.2. Handling shall be performed carefully to prevent damage of machined surfaces, deletion of identification and distortion
of products.
7.2.3. The length of wire depends on size of product, and the angels between wires can’t exceed 60° generally.
7.2.4. Every handling tools or equipment shall be checked for their capability before using.
7.2.5. The experienced or trained person shall be assigned to the working that need special handling or lifting equipment.
Handling Instruction
Sling belt
Rev.0 27 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
NAME OF LETTERS
NO MARK STENCILED REMARKS
MARK STENCILED
Handle
5 Fragile For fragile cargo
with care
Heavy Heavy
When center of gravity
6 weight weight
is on one side
this end this end
Do Do
For Precision Goods,
7 Not Not
fragile
Stack Stack
Rev.0 28 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Rev.0 29 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
1) Case
Size:10~20cm
1. Panels(Front, Rear, Sides and Top) of the Case are made of plywood.
2. For top panel assembly process, install plywood first and apply corner protectors at the upper corners. Finally, cover its top with vinyl and install
the tent.
Rev.0 30 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
2) Crate
Size:10~20cm
1. Panels(Front, Rear, Sides and Top) of the Crate are made of lumber.
2. Water proof paper shall be applied to the inside of panels(Front, Rear and Sides) to prevent water inflow.
3. For top panel assembly process, install plywood(3t) first and cover it with vinyl and assemble lumber. Finally, apply corner protector at the
upper corner and install the tent.
Rev.0 31 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
3. Joist Support and Aux. Strut shall be applied to the boxes(Internal height is 1,400 mm or over) for domestic and the all boxes for export.
4. Joist Support and Aux. Strut shall be applied to same size of Horizontal Member and Strut.
5. For the boxes made by plywood, 12T plywood shall be applied. But, 9T plywood can be allowed for boxes(weight of product ≤ 2 Ton)
for domestic.
6. For the boxes made by lumber, 18T lumber shall be applied. But, 15T lumber can be allowed for boxes(weight of product < 6 Ton).
7. For the non-load bearing floor member, 18T lumber shall be applied. But, 15T lumber can be allowed for boxes(weight of product < 6 Ton).
Rev.0 32 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
[Table 3] Header/Load Bearing Floor Member of Wooden Frame Box [Unit: mm]
140
Corner Protector
mm
Edge Protector
Rev.0 33 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Plywood Cover
Bolts & Nuts
Base Plate
Saddle
Waterproof adhesive tape
Skid
Metal Cover
Gasket
Detail “A”
Saddle
Rev.0 34 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Sling Mark
Center of Gravity Mark
Sling Mark
Main Shipping Mark Center of Gravity Mark
Rev.0 35 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Care Mark
(Side) (Side)
(Front)
Packing List
Cover
Main
Shipping Mark
(Back)
Main
Shipping Mark
Center of Gravity Mark
Sling Mark
Rev.0 36 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Header
E ● ● ●
D ● ● ● ●
Link
E ● ● ● ● ●
D ● ●
Steam Drum
E ● ●
Pressure Part
D ● ● ●
Furnace Wall
E ● ● ●
D ● ●
SH, RH, Economizer Tube
E ● ●
D ●
Hanger
E ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Embedded Material
E ● ●
Angle, Base Plate, Bracket D ● ●
Flat Bar, Pad, Pipe (L ≤ 1m) E ● ●
Angle, Base Plate, Bracket D ● ●
Flat Bar, Pad, Pipe (L > 1m) E ● ●
D ● ● ●
Steel Structure Beam, Column, Girder, Brace
E ● ● ●
D ● ● ●
Ladder, Platform, Hand rail stair
E ● ● ●
D ●
Bolt, Nut & Washer
E ●
D ● ●
Grating
E ● ●
Rev.0 37 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
A.3 Buckstay
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Anchor
E ●
D ● ●
Plate
E ● ●
D ● ● ● ●
Channel
E ● ● ● ●
Buckstay
D ● ● ● ●
H-Beam
E ● ● ● ●
D ● ● ●
Pipe
E ● ● ●
D ●
Misc.
E ●
A.4 Absorber
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Mo Plate
E ● ● ●
D ● ●
Alloy Steel Pipe
E ●
D ●
Bolt/Nut/Washer
E ●
D ● ● ●
C276 Plate
E ● ● ●
Absorber D ●
Mist Eliminate
E ● ●
D ●
Oxidation Air Blower
E ●
D ● ●
Side Agitator(**)
E ● ●
D ● ● ● ● ●
Spray Nozzle
E ● ● ● ● ●
Rev.0 38 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Spray Bank
E ● ● ●
D ●
Welding Rod
E ●
D ● ●
Absorber Pump
E ● ●
D ● ●
Motor
E ● ●
D ● ● ● ● ● ● ●
Steel Structure
E ● ● ● ● ● ● ●
(**) shall be packed in moisture proof box in case of being assembled with electrical part.
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ● ●
Rotor & Housing
E ● ● ● ● ●
D ●
Rotor Driving Units(Reducer)
E ●
D ●
Lubrication Units
E ●
D ●
Bearing, Bearing Housing
E ●
D ●
Air Preheater Trunnion Shaft, Guide Trunnoin
E ●
D ● ●
Air Motor
E ● ●
D ● ●
Elements & Baskets
E ●
D ●
Water Washing System
E ●
D ●
I&C
E ●
Rev.0 39 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Air Preheater Misc.
E ● ● ● ●
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Slide Gate / Bar Gate
E ● ●
D ● ● ●
Vibrator, Vibrating bin Activator
E ● ● ●
D ● ● ●
Emergency Take-off Chute
E ● ● ●
Limestone D ●
Weighing feeder
Slurry E ●
Preparation D ● ● ●
System Pump & Motor
E ● ●
D ●
Classifiers
E ●
D ● ● ●
4-way Product Distribution Box
E ● ● ●
D ● ●
Ball Charging Device
E ● ●
A.7 Burner
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Burner Accessory
E ●
D ● ●
Coal Burner Coal Burner
E ● ●
D ● ●
OFA Burner
E ● ●
Rev.0 40 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Accumulator
E ●
D ●
Gun Cleaning Table
E ●
D ●
Oil Burner & Ignitor
E ●
Oil Burner
D ●
Relief Valve
E ●
D ●
Shu-off Valve
E ●
D ● ●
Valve Skid(Rack) for Oil Burner
E ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Cable
E ● ●
D ● ● ● ●
Cable Tray
E ● ● ● ●
D ●
Adapter & Socket
E ●
D ● ● ● ●
Conduit
E ● ● ● ●
Cable & Conduit
D ●
Coupling
E ●
D ●
Condulet
E ●
D ●
Flexible Connector & Tube
E ●
D ● ● ● ●
Pipe
E ● ● ● ●
Rev.0 41 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Normal Bend
E ●
D ●
Reducer For Round Junction Box
E ●
D ●
Cable & Conduit Round Junction Box
E ●
D ● ●
Cable Reel
E ● ●
D ●
Misc.
E ●
(*) can be packed in Pallet, Wooden bundle type in case of shipping/storage with container
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Coal Feeder
E ●
D ●
Coal Feeder Panel
E ●
D ●
Loose & Spare Parts
E ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Valve
E ●
Hp Bypass D ● ● ●
& HPU
RH Safety Valve E ● ●
D ●
Panel
E ●
Rev.0 42 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
Hp Bypass D ●
& Misc.
RH Safety Valve E ●
A.11 Duct
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Duct
E ● ● ● ●
Structure(Hand Rail, Walkway, D ● ● ● ● ● ● ●
H-Beam, etc.) E ● ● ● ● ● ● ●
D ● ● ●
Rigid Hanger
E ● ● ●
D ●
Spring Hanger
E ●
D ● ● ●
Duct Sliding Pad
E ● ● ●
D ●
Gauge Connection
E ●
D ● ● ●
Expansion Joint
E ● ●
D ● ● ●
Insulation(*)
E ● ● ●
D ●
Misc.
E ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
Rev.0 43 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Mould & Catridge
E ●
D ● ●
Bus bar & Copper Rod
E ● ●
D ●
Bare Copper Conductor
E ●
D ●
Clamping Accessories
E ●
Earthing & Lightning
D ●
Air Terminal & Base
E ●
D ●
Test Box
E ●
D ● ● ●
Channel
E ● ● ●
D ● ●
Cable
E ● ●
A.13 EP
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Casing
E ● ● ● ●
Casing
D ● ●
Hopper
E ● ●
D ● ● ● ●
Steel Structure Steel Structure
E ● ● ● ●
D ●
CE & DE CE & DE
E ●
D ● ● ●
Rapping System Rapping System
E ● ● ●
D ● ●
Elec. & Instrument Transformer Rectifier
E ● ● ●
Rev.0 44 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Panel
E ●
D ● ●
Instrument
E ● ●
Elec. & Instrument
D ● ●
Motor
E ● ●
D ●
Bus Duct
E ●
D ● ●
Gas Distribution
E ● ●
D ●
Seal Air Blower
E ●
D ●
Seal Air Heater
E ●
D ●
Hoist
E ●
D ●
Valve
E ●
Others
D ● ● ●
Cable Tray, Conduit Pipe
E ● ● ●
D ● ●
Cable
E ● ●
D ● ● ● ●
Piping
E ● ● ● ●
D ● ● ●
Insulation(*)
E ● ● ●
D ●
Misc.
E ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
Rev.0 45 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Electrical Ass’y For Lifting Device
E ●
D ● ● ● ●
Girder Crane For Lifting Device
E ● ● ● ●
Lifting Device
D ●
Hoist For Lifting Device
E ●
D ●
Monorail for Lifting device
E ●
A.15 Fan
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Fan Casing Assembly
E ●
D ●
Upper/Lower Fan Casing
E ●
D ●
Upper/Lower Diffuser
E ●
D ●
Upper/Lower Suction Box
E ●
D ●
Rain Hood
E ●
D ● ● ●
Fan Lagging
E ● ● ●
D ● ● ●
Lining Plate
E ● ● ●
D ● ● ●
Oil Supply Unit
E ● ●
D ● ●
Terminal Box
E ●
D ● ● ●
Expansion Joint
E ● ●
D ● ● ● ●
Duct
E ● ● ● ●
Rev.0 46 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Fan Foundation Material
E ●
D ● ● ●
Fan Insulation(*)
E ● ● ●
D ● ● ● ●
Platform
E ● ● ● ●
D ● ● ● ●
Silencer
E ● ● ● ●
D ● ● ● ●
Diffuser
E ● ● ● ●
D ●
Valve & Pipe Fitting
E ●
D ● ● ● ● ●
Pipe
E ● ● ● ● ●
D ●
Intermediate Shaft
E ●
D ●
Panel
Fan E ●
D ●
Motor
E ● ●
D ●
Compensator
E ●
D ●
Blade & Accessory
E ●
D ●
Anchor Box
E ●
D ●
Anchor Plate
E ●
D ● ●
Actuator(**)
E ● ●
D ● ● ● ●
Oil
E ● ● ● ●
D ●
Cooling Fan Assembly
E ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
(**) shall be packed in moisture proof box in case of being assembled with electrical part.
Rev.0 47 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Mill Seal Air Fan
E ●
D ●
Penthouse Fan
E ●
D ●
Purge Air Fan
E ●
D ●
Fan Scanner Cooling Air Fan
E ●
D ●
Electric Equipment
E ●
D ●
Loose Parts
E ●
D ● ●
Spare Parts
E ● ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Rotor & Casing
E ● ● ● ●
D ● ● ●
Sealing System
E ● ● ●
D ●
Rotor Drive Unit
E ●
D ● ● ●
Gas Gas Heater Seal air and Drying air system
E ● ● ●
D ●
Bearing Housing
E ●
D ● ●
Sootblower
E ● ●
D ● ●
Heating Element
E ●
Rev.0 48 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
High Pressure Pump & Motor
E ●
D ● ●
Actuator(**)
E ● ●
D ●
Gas Gas Heater bearing
E ●
D ● ● ● ●
Fan
E ● ● ● ●
D ● ●
Valve
E ● ●
(**) shall be packed in moisture proof box in case of being assembled with electrical part.
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Support Beam
E ● ● ● ●
D ● ● ● ●
Pipe Support
E ● ● ● ●
Down comer D ●
Spring Hanger
Pipe Support E ●
D ● ● ● ●
Rod
E ● ● ● ●
D ●
Misc.
E ●
Disk Spring D ●
Disk Spring Hanger
Hanger E ●
D ● ●
RE Strut RE Strut
E ●
D ●
Collector
Pressure Part E ●
Rigid Hanger D ● ● ● ●
Support Beam
E ● ● ● ●
Rev.0 49 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Pipe Support
E ● ● ● ●
Spring Hanger D ●
Pipe Support D ● ● ● ●
Pressure Part
Rigid Hanger D ● ● ● ●
Rod
E ● ● ● ●
D ●
Misc.
E ●
D ● ● ● ●
Support Beam
E ● ● ● ●
D ● ● ● ●
Pipe Support
E ● ● ● ●
Variable Spring D ●
Spring Hanger
Hanger E ●
D ● ● ● ●
Rod
E ● ● ● ●
D ●
Misc.
E ●
A.18 Pump
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Drum
Skid
D ●
Pump
E ●
D ●
Pump Pump with electrical assembly
E ●
D ●
Misc.
E ●
Rev.0 50 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
A.19 Insulation
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Aluminum Alloy Sheet(*)
E ● ● ●
D ● ● ●
Aluminum Alloy Ribbed Panel(*)
E ● ● ●
D ● ● ●
Calcium Silicate Pipe Cover(*)
E ● ● ●
Insulation
D ● ● ●
Fiber Board(*)
E ● ● ●
D ● ● ●
Refractory Material(*)
E ● ● ●
D ●
Misc.
E ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
A.20 RH Attemperator
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Control Valve
E ● ●
D ● ●
RH Attemperator RH Attemperator
E ● ●
D ●
Misc.
E ●
A.21 Motors
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Motors Motor for Recirculation Pump
E ● ●
Rev.0 51 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Ac Power Distribution Panel
E ●
D ● ● ●
Cab Distribution/Remote I/O Panel
E ●
D ● ●
Cabin Display Box
E ●
D ● ● ●
Communication Cable
E ●
D ● ● ●
Motors Gantry Motor
E ●
D ● ● ●
Hoist Motor
E ●
D ● ●
Software For Maintenance
E ●
D ● ● ●
Trolley Motor
E ●
D ● ● ●
Trolley/Spreader Panel
E ●
A.22 Piping
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Drum
Skid
D ● ● ● ● ●
Integral pipe
E ● ● ● ● ●
D ● ● ● ● ●
Misc. pipe
E ● ● ● ● ●
D ● ● ● ● ●
Piping Scanner Cooling Air Piping
E ● ● ● ● ●
D ●
Hanger
E ●
D ● ● ●
Insulation(*)
E ● ● ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
Rev.0 52 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Pipe for Expansion joint
E ● ●
Piping
D ●
piping for Flange
E ●
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Panel
E ●
D ● ●
Soot Blower Soot Blower
E ● ●
D ●
Misc.
E ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Steel Structure
E ● ● ● ●
D ● ●
Ammonia Injection Grid
E ● ●
D ●
Dilution Air Blower
Ammonia E ●
Injection &
Reactor D ●
Sootblowing System
E ●
D ● ● ●
Static Mixer
E ● ● ●
D ● ●
NH3/AIR Mixer
E ●
Rev.0 53 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Ammonia Unloading Compressor
E ●
D ● ●
Ammonia Storage Tank
E ● ●
D ● ●
Vaporizer
E ● ● ●
Ammonia D ● ●
Accumulator
Storage E ● ● ●
D ● ●
Waste Ammonia Dilution Tank
E ●
D ●
Sump Pump
E ●
D ● ●
NH3/AIR Mixer
E ●
D ● ● ● ●
Catalyst Catalyst(*)
E ● ● ● ●
D ●
Nozzle, Valve
E ●
D ● ● ● ●
Steel Structure
E ● ● ● ●
Misc.
D ● ●
Instrument
E ● ●
D ● ● ●
Piping
E ● ● ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
A.25 Tanks
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Carbon Plate
E ● ●
Tanks
D ● ●
Top Side Agitator(**)
E ● ●
Rev.0 54 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
Steam Coil Air Preheater D ● ●
Drain Tank E ● ●
Flash Tank D ● ●
Tanks
(CBD Tank) E ● ●
Blowdown Tank D ● ●
(IBD Tank) E ● ●
(**) shall be packed in moisture proof box in case of being assembled with electrical part.
A.26 Pulverizer
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Mill Stand
D Skid
● ● ●
E ● ● ●
D ● ● ● ●
Mill Stand - Foundation Frame
E ● ● ● ●
D ● ●
Mill Stand - Pedestal
E ● ●
D ● ●
Mill Stand - Gas Duct
E ● ●
D ● ●
Mill Stand - Ring Duct
E ● ●
D ● ●
Mill Body, Cpl. & Table, Cpl.
E ● ●
Pulverizer
D ● ●
Bridge
E ● ●
D ● ●
Grinding Tire
E ● ● ●
D ●
Funnel
E ●
D ●
Rocker Arm & Grinding Roller
E ●
D ●
Spring Assembly, Cpl.
E ●
D ● ●
Reject Box, Cpl.
E ● ● ●
Rev.0 55 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Lm-Drive, Cpl.
E ●
D ● ● ● ●
Mill Platform
E ● ● ● ●
D ● ● ● ●
Seal Air Pipe
E ● ● ● ●
D ● ● ● ●
Miscellaneous Pip`e
E ● ● ● ●
D ● ●
Miscellaneous Material
E ● ●
Pulverizer
D ●
Hydraulic Cabinet
E ●
D ● ●
Classifier
E ● ●
D ● ●
Motor
E ● ●
D ●
Gear Box
E ●
D ● ●
Knife Gate Valve
E ●
A.27 Valve
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Drum
Skid
D ●
Hydraulic Valve
E ●
D ●
Casting Manual Valve
E ●
D ●
Check Valve
E ●
Valve
D ●
Forging Manual Valve
E ●
D ● ●
Motor Operated Valve
E ● ●
D ●
Control Valve
E ●
Rev.0 56 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Butterfly Manual Valve
E ●
Valve
D ●
Safety Relief Valve Package
E ●
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Cabinet
E ●
D ● ● ●
Base Frame
E ● ●
D ● ●
DCS Cable
E ● ●
D ● ●
PC/Monitor/Printer Box
E ● ●
D ●
Misc.
E ●
D ● ●
Others
E ● ●
Others
D ● ●
Instrument
E ● ●
D ● ●
Accessory Accessory
E ● ●
D ●
Analyzer
E ●
D ●
CCTV
E ●
D ●
System Flame Scanner
E ●
D ●
Boiler Tube Leak Detection
E ●
D ● ●
Lighting
E ● ●
Rev.0 57 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Indoor Unit
E ●
Air Conditioner
D ● ●
Out Door Unit
E ●
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
Drive Unit(Motor, Brake, Coupling, D ●
Reducer, Common Bed) - Shop
Assembled E ●
D ●
Local Control Station(LCS)
E ●
D ●
Coupling
E ●
D ●
Thrust Drum Brake
E ●
D ●
Gear Reducer
E ●
D ● ●
Drive Base(Common Bed)
E ● ●
Belt Conveyor D ●
Back Stop
Components E ●
Conveyor Pulley Ass'y (With Bearing, D ●
Plummer Block, Backstop) - Shop
Assembled) E ●
D ●
Idler Roller
E ●
D ● ● ●
Idler Stand
E ● ● ●
D ● ● ●
Conveyor Belt
E ● ● ●
D ●
Belt Cleaner
E ●
D ● ● ●
Screw Take-Up Device
E ● ● ●
Rev.0 58 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
All Fastening Materials
Belt Conveyor E ●
Components D ●
Misc.
E ●
D ● ● ●
Skid Base Under The Common Bed
E ● ● ●
D ● ● ●
Pulley Frame And Basement
E ● ● ●
Take-Up Structure And Device With D ● ● ●
Weight Box E ● ● ●
D ● ● ● ●
Stringer & Support
E ● ● ● ●
Conveyor Cover(Hood Cover, Side D ● ● ●
Belt Conveyor Cover, Bottom Deck Plate, Etc) E ● ● ●
Fabrication
Items D ● ● ● ●
Deck Plate
E ● ● ● ●
D ● ● ● ●
Chute And Skirt Board
E ● ● ● ●
D ● ● ● ●
All Liner Plate
E ● ● ● ●
D ● ● ● ●
Safety Guard
E ● ● ● ●
D ●
Misc.
E ●
Dust Collector Ass'y(Include Body D ● ●
And Hopper) E ● ●
D ●
Filter, Cage, Flexible Joint, Etc.
E ●
Dust Return Equipment With Drive D ●
Dust Collection Unit And Base Frame E ●
System and D
Access Way, Platform, Stairway, ● ● ● ●
Vacuum
Ladder, Etc. E ● ● ● ●
Cleaning
System D ●
Auto Damper with Air Cylinder
E ●
D ● ●
Inlet/Outlet Duct
E ● ●
Dust Suction Hood with Manual D ● ● ●
Damper E ● ● ●
Rev.0 59 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Fan & Drive Unit with Common Bed
E ●
D ● ● ● ●
Stack And Support Structure
E ● ● ● ●
Dust Collection All Air Supply System with Piping D ● ●
System and Material And Support E ● ●
Vacuum
Cleaning All Fastening D ●
System Materials(Bolt/Nut/Washer, etc.) E ●
D ●
Electrical & Control Panel
E ●
D ●
Misc.
E ●
Spray Water Pump with Control D ● ●
Panel And Base Frame E ● ●
D ●
Dust All Spray Nozzle And Piping
E ●
Suppression
System D ●
All Electrical And Control Equipment
E ●
D ●
Spray Monitor Gun
E ●
D ●
Electrical Motor
E ●
D ●
Control Panel
E ●
Field Instruments (Limit Switch, D ●
Sensor, Fan, Ventilation, Air
Conditioner, Etc.) E ●
D ● ● ●
Cable/Hose Reel
E ● ● ●
D ● ●
Cellular/Rubber Buffer
Stacker & E ● ●
Reclaimer D ●
Slew Bearing
E ●
D ●
Air Conditioner
E ●
D ●
Gear Reducer
E ●
D ● ●
Shrink Disc
E ● ●
D ●
Hyd. Unit/Hyd. Cylinder
E ●
Rev.0 60 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
Pipe & Fitting, Distributor & Pipe D ● ● ●
Cover (Hyd.) E ● ● ●
D ● ●
Hyd. Cylinder
E ● ●
D ● ●
Plummer Block
E ● ●
D ● ●
Lubrication Unit
E ● ●
D ● ● ●
Conveyor Belt
E ● ● ●
D ● ●
Idler Roller
E ● ●
D ● ● ● ●
Idler Stand
E ● ● ● ●
Stacker & D ● ●
Belt Scale
Reclaimer E ● ●
D ● ● ●
Take Up Device
E ● ● ●
D ● ●
Belt Cleaner
E ● ●
D ● ●
Conveyor Pulley
E ● ●
D ● ● ●
Cable Ducts & Accessory
E ● ● ●
D ● ●
Wheel
E ● ●
D ● ●
Shaft & Pin
E ● ●
D ● ●
Misc.
E ● ●
Conveyor Frame and D ● ● ● ●
Structure(Girder) for All Conveyors E ● ● ● ●
Stairway, Walkway, Grating, D ● ● ● ●
Structure
Handrail, etc. E ● ● ● ●
D ● ● ● ●
Maintenance & Access Platform
E ● ● ● ●
D ● ●
Others Vibrating/Belt Feeder
E ● ●
Rev.0 61 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ●
Magnetic Separator
E ● ●
D ● ●
Vibrating Screen(Two-Stage Type)
E ● ●
D ● ●
Divert Gate with Motor Cylinder
E ● ●
D ● ●
Belt Scale
E ● ●
D ● ●
Electrical Hoist
E ● ●
D ● ●
V - Scraper
E ● ●
Others
D ● ●
Sampling System(Modular Type)
E ● ●
Steel Fabrication Item of Package D ● ● ● ●
Equipment E ● ● ● ●
Mechanical Rotating Item of D ● ●
Package Equipment E ● ●
Electrical Rotating Item of Package D ● ●
Equipment E ● ●
Electrical And Control Panel of D ●
Package Equipment E ●
D ●
Misc.
E ●
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Transition Hopper Plate
E ● ● ●
D ● ●
Insulation
E ● ●
Bottom ASH D ● ● ●
Handling Refractory
System E ● ● ●
D ●
Bottom Door
E ●
Dry Bottom Ash Conveyor Casing D ● ● ●
Ass’y E ● ● ●
Rev.0 62 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Conveyor Chain Ass’y
E ● ● ●
D ● ● ●
Conveyor Pan Ass’y
E ● ● ●
D ●
O-chain
E ●
D ● ●
Pre Crusher
E ● ● ●
Bottom ASH D ● ●
Handling Crusher
System E ● ● ●
D ● ●
Crusher Tower
E ● ●
D ● ●
Bottom Ash Silo
E ● ●
D ● ●
Bottom Silo Wet & Dry Unloader
E ● ● ●
D ● ● ●
Bag Filter and Fan
E ● ● ●
D ● ● ●
Air-lock Vessel
E ● ● ●
D ● ● ● ● ●
Air Pipe and Fitting (Carbon steel)
E ● ● ● ● ●
D ● ● ● ● ●
Ash Pipe and Fitting
E ● ● ● ● ●
D ●
Valves
E ●
D ● ● ●
Transport/Fluidizing/Aeration Blower
FLY ASH E ● ● ●
Handling D ● ● ●
System Compressor & Dryer
E ● ● ●
D ● ● ●
Heater
E ● ● ●
D ● ●
Fly Ash Silo
E ● ●
D ● ● ●
Vent Filter and Fan
E ● ● ●
D ●
Aeration Stone ●
E
Rev.0 63 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ●
Fly Ash Silo Wet & Dry Unloader
E ● ● ●
D ● ● ●
FLY ASH Bag Filter and Fan
E ● ● ●
Handling
System D ● ●
Surge Hopper
E ● ●
D ● ● ● ● ●
Pipe-rack
E ● ●
D ● ● ●
Pyrite Screw Conveyor
E ● ● ●
D ● ● ●
Pyrite Transport Belt Conveyor
E ● ● ●
Pyrite Storage Container (Arm-roll D ● ● ●
box) E ● ● ●
Pyrite Handling D ● ● ●
Pyrite Conveyor Support Structure
System E ● ● ●
D ● ●
Pyrite Hopper
E ● ●
D ● ● ●
Pyrite Hopper Bag Filter & Fan
E ● ● ●
Pyrite Hopper gate & Telescopic D ● ● ●
chute E ● ● ●
A.31 BOP
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ●
Bag Filter and Fan
E ●
D ●
Water Box Vacuum Pump
Condenser Aux. E ●
System D ● ●
Vacuum Control Tank
E ●
D ● ●
Cathodic Protection System
E ●
Rev.0 64 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
Condenser Aux. D ● ● ●
Steam Jet Air Ejector
System E ● ●
D ●
HP Heater
E ●
D ●
LP Heater
E ●
D ●
Drain Cooler
E ●
Heat Exchanger
D ●
Deaerator & Storage Tank
E ●
D ●
DH Heater
E ●
D ●
Heat Exchanger
E ●
D ●
Shop Tank
E ●
Tank
D ●
Steel Plate for Site Tank
E ●
Platform & D ● ● ●
Platform & Ladder
Ladder E ● ● ●
D ●
Strainer Section Assembly
E ●
D ●
Ball Recirculation Unit
E ●
CTCS/DF
D ●
Control Panel
E ●
D ●
Debris Filter Assembly
E ●
D ● ● ●
GCB, IPB
E ● ●
D ● ● ● ●
Transformer Main Transformer
E ● ● ● ●
D ● ● ● ●
Aux. Transformer
E ● ● ● ●
Rev.0 65 of 66
PACKING PROCEDURE
VA2-DL01-P0ZEN-090001
Packing Type
D(Domestic)
Wooden Bundle
Steel Frame
Open Crate
Steel Skid
Container
Division Item
Pallet
Drum
Skid
D ● ● ● ●
Embedded Material
E ● ● ● ●
D ● ● ●
Others Insulation(*)
E ● ● ●
D ●
Gasket
E ●
(*) can be packed in pallet, wooden bundle type in case of shipping/storage with container.
Rev.0 66 of 66