Professional Documents
Culture Documents
Errection and Take Down Chart - Aat - 12870-09-02 LR 1750
Errection and Take Down Chart - Aat - 12870-09-02 LR 1750
Lattice boom
crawler track crane
LR 1750
Erection
and
take down charts
Preface
The boom can be erected or taken down to teh side or in length axle of the crawler gear.
D A N G E R: The erection and take down procedure must be made according to the data in the
erection and take down chart.
If this is not observed, the crane can be overloaded or topple over!
C A U T I O N: If the mechanical auxiliary support is installed, then it must be erected/ taken down
over the same in length axle direction >0∞> .
The deviation to the length axis >0∞> may be max. ± 5,0∞ .
It is strictly prohibited to exceed this maximum deviation, also when raising or lo>
wering the pulley block.
If not observed, the crane might topple over!
If no pulley assembly or if the 400 t pulley assembly is installed on the S> head, then
the S> and W> booms can be run together during erection / take down to a minimum
intermediate angle of 45∞ .
If the 600 t pulley assembly is installed on the S> head, then the S> and W> booms
can be run together during erection / take down to a min. angle of 90∞ .
ERECTION AND TAKE DOWN CHARTS
Installation conditions
1 = with placed down SA bracket (with and without cable on winch IV)
2 = 90∞ SA bracket (with cable on winch IV)
3 = with placed down SA bracket, winch I and IV mit Seil
4 = 90∞ SA> bracket, winch I and IV with cable
5 = 90∞ SA> bracket, winch I and IV with cable, S> pivot section installed
Chart 1: Max. permissible slewing platform ballast for the following installation conditions
in operation on crawlers
Installation A B
condition
360∞on crawler 360∞on crawler
9,1 m x 8,8 m 9,1 m x 8,8 m
Central ballast Supports installed
incl. central ballast 20 t
95 t 70 t 45 t 20 t
Chart 2: Max. permissible slewing platform ballast for the following installation conditions
in operation on supports
Installation C D* E F
condition
360∞ 360∞ to the side 360∞
on supports on supports on supports on supports
12,6 m x 12,6 m 12,6 m x 12,6 m 16,0 m x 10,5 m 16,0 m x 10,5 m
central ballast 110 t
Chart 3: Max. permissible slewing platform ballast for the following installation conditions in
operation on supports with installed crawler
Installation D G H
condition
360∞ to the side 360∞
on supports on supports on supports
13,0 m x 13,0 m 16,0 m x 12,0 m 16,0 m x 12,0 m
crawler installed crawler installed crawler installed
incl. central ballast incl. central ballast incl. central ballast
20 t 20 t 20 t
1
245 245 245
2 Max.
245 245 245
3 permissible
245 245 245
4 slewing
245 245 245
5 platform
245 245 245
ballast
1 Max.
2 permissible
250 250 200
3 slewing
250 250 200
4 platform
250 250 200
5 ballast on
250 250 225
slewing
250 250 225
platform
extension
ERECTION AND TAKE DOWN CHARTS
CAUTION: The determining factors are the corresponding erection charts and taking into
account charts (1 > 3)
Erection Erection
Required slewing platform ballast Required slewing platform ballast according to erection chart > max.
according to erection chart permissible slewing platform ballast according to chart 1>3
<= max. permissible slewing
platform ballast according to chart
1>3
Procedure as for erection in 1. Before installation of the boom, only the max. permissible slewing
operation on crawlers. platform ballast according to chart 1>3 may be placed.
2. Before pulling the main boom guying, the max. permissible
slewing platform ballast according to chart 1>3 must be placed.
3. The main boom guying must be tensioned. The relieved supports
may not lift off.
Check figure data via max. permissible guy force / slewing ring
overload
4. The required slewing platform ballast according to the erection
charts must be placed.
5. The boom can be pulled up.
Take down Take down
Required slewing platform ballast Required slewing platform ballast according to erection chart > max.
according to erection chart <= permissible slewing platform ballast according to chart 1 > 3
max. permissible slewing platform
ballast according to chart 1>3
Procedure as for take down in 1. Place down the boom; the main boom guying must remained
operation on crawlers . tensioned
2. Remove the slewing platform ballast until only the max.
permissible slewing platform ballast according to chart 1>3 is
placed.
3. The main boom guying can be relieved.
4. The main boom can be removed.
Wind speed
m/s 2 4 6 8 10 12 14 16
km/h 7,2 14,4 21,6 28,8 36,0 43,2 50,4 57,6
Knoten 3,9 7,8 11,7 15,6 19,4 23,3 27,2 31,1
ft/s 6,6 13,1 19,7 26,2 32,8 39,4 45,9 52,5
mile/h 4,5 8,9 13,4 17,9 22,4 26,8 31,3 35,8
m/s 18 20 22 24 26 28 30 32
km/h 64,8 72,0 79,2 86,4 93,6 100,8 108,0 115,2
Knoten 35,0 38,9 42,8 46,7 50,5 54,4 58,3 62,2
ft/s 59,1 65,6 72,2 78,7 85,3 91,9 98,4 105,0
mile/h 40,3 44,7 49,2 53,7 58,2 62,6 67,1 71,6
Back pressure
Wind velocity
km/h 50 > 61 62 > 74 75 > 88 89 > 102 103 > 117 118 > 133
Beaufort 7 8 9 10 11 12
ERECTION AND TAKE DOWN CHARTS
193762
ERECTION AND TAKE DOWN CHARTS
SD / SDB > Operation (derrick ballast R = 13 m) ................... TAB: 12800040 ........ 147
SD / SDB > Operation (derrick ballast R = 15 m) ................... TAB: 12800041 ........ 148
SD / SDB > Operation (derrick ballast R = 18 m) ................... TAB: 12800042 ........ 149
SD / SDB > Operation (derrick ballast R = 20 m) ................... TAB: 12800043 ........ 150
SD / SDBW > Operation (derrick ballast R = 13 m) ................. TAB: 12800044 ........ 151
SD / SDBW > Operation (derrick ballast R = 15 m) ................. TAB: 12800045 ........ 152
SD / SDBW > Operation (derrick ballast R = 18 m) ................. TAB: 12800046 ........ 153
SD / SDBW > Operation (derrick ballast R = 20 m) ................. TAB: 12800047 ........ 154
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast _R = 13 m, 600 t pulley set on S> head) . . . . . TAB: 12800135 ........ 289
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast _R = 15 m, 600 t pulley set on S> head) . . . . . TAB: 12800136 ........ 300
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast _R = 18 m, 600 t pulley set on S> head) . . . . . TAB: 12800137 ........ 311
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast _R = 20 m, 600 t pulley set on S> head) . . . . . TAB: 12800138 ........ 322
SDWBW > Operation with hydr. erection device for WA> bracket II
(Derrick ballast _R = 13 m, 600 t pulley set on S> head) . . . . . TAB: 12800139 ........ 333
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast _R = 15 m, 600 t pulley set on S> head) . . . . . . TAB: 12800140 ........ 344
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast _R = 18 m, 600 t pulley set on S> head) . . . . . . TAB: 12800141 ........ 355
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast _R = 20 m, 600 t pulley set on S> head) . . . . . . TAB: 12800142 ........ 366
SDWV / SDWVB(W) > Operation, 360∞, without auxiliary support . . . TAB: 12800098 ........ 222
SDWV / SDWVB(W) > Operation, 360 ∞, without auxiliary support . . . TAB: 12800167 ........ 394
1
ERECTION AND TAKE DOWN CHARTS
SDWVB (W) > Operation (derrick ballast R = 13 m) ............... TAB: 12800057 ......... 163
SDWVB (W) > Operation (derrick ballast R = 15 m) ............... TAB: 12800058 ......... 165
SDWVB (W) > Operation (derrick ballast R = 18 m) ............... TAB: 12800059 ......... 167
SDWVB (W) > Operation (derrick ballast R = 20 m) ............... TAB: 12800060 ......... 169
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) . . . . . . . . . TAB: 12800147 . . . . . . . . . 378
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) . . . . . . . . . TAB: 12800148 . . . . . . . . . 380
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) . . . . . . . . . TAB: 12800154 . . . . . . . . . 384
SL > Operation (SL4HS) with auxiliary jib 120t (HS 6,0 m) . . . . . . . . . TAB: 12800149 . . . . . . . . . 382
SL8DHS operation with auxiliary jib 120 t (HS 6.0 m) . . . . . . . . . . . . . TAB: 12800179 . . . . . . . . . 398
SL8DHS operation with auxiliary jib 120t (HS 6.0 m) . . . . . . . . . . . . . . TAB: 12800181 . . . . . . . . . 399
SLD > operation (SL7DHS) with auxiliary jib 120t (HS>6,0 m) . . . . . . . TAB: 12800155 . . . . . . . . . 386
SLD > operation (SL7DHS) with auxiliary jib 120t (HS>6,0 m) . . . . . . . TAB: 12800156 . . . . . . . . . 387
SLD / SLDB > Operation (derrick ballast R = 13 m) ................ TAB: 12800048 ......... 155
SLD / SLDB > Operation (derrick ballast R = 15 m) ................ TAB: 12800049 ......... 156
SLD / SLDB > Operation (derrick ballast R = 18 m) ................ TAB: 12800050 ......... 157
SLD / SLDB > Operation (derrick ballast R = 20 m) ................ TAB: 12800051 ......... 158
SLD / SLDBW > Operation (derrick ballast R = 13 m) .............. TAB: 12800052 ......... 159
SLD / SLDBW > Operation (derrick ballast R = 15 m) .............. TAB: 12800053 ......... 160
SLD / SLDBW > Operation (derrick ballast R = 18 m) .............. TAB: 12800054 ......... 161
SLD / SLDBW > Operation (derrick ballast R = 20 m) .............. TAB: 12800055 ........ 162
2
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA > bracket II (S> head
pulley set _600 t, slewing platform / central ballast 70 / 20 t) . TAB: 12800131 ........ 282
SW > Operation (250 t Ballast on slewing platform extension) . . . . . . . TAB: 12800037 ........ 142
SW > Operation (250 t Ballast on slewing platform extension)
600 t pulley set on S > head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800115 ........ 251
SW > Operation (250 t ballast on slewing platform extension)
600 t Pulley set on S > head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800116 ........ 253
SW > Operation (Slewing platform ballast 120 t) . . . . . . . . . . . . . . . . . . . TAB: 12800034 ........ 136
SW > Operation (Slewing platform ballast 170 t) . . . . . . . . . . . . . . . . . . . TAB: 12800032 ........ 132
SW > Operation (Slewing platform ballast 220 t) . . . . . . . . . . . . . . . . . . . TAB: 12800030 ........ 128
SW > Operation (Slewing platform ballast 245 t) . . . . . . . . . . . . . . . . . . . TAB: 12800028 ........ 124
SW > Operation (Slewing platform ballast 70 t) . . . . . . . . . . . . . . . . . . . . TAB: 12800036 ........ 140
3
ERECTION AND TAKE DOWN CHARTS
SW > Operation 250 t Ballast on slewing platform extension ........ TAB: 12800038 . . . . . . . . . 144
SW > Operation with hydr. erection device for WA bracket II . . . . . . . TAB: 12800081 ......... 187
SW > Operation with hydr. erection device _for WA> bracket II . . . . . TAB: 12800076 ......... 177
SW > Operation with hydr. erection device _for WA > bracket II . . . . . TAB: 12800077 ......... 179
SW > Operation with hydr. erection device _for WA bracket II . . . . . . . TAB: 12800078 ......... 181
4
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II (S> head
pulley set 600 t, slewing platform / Central ballast 170 / 20 t) ^ TAB: 12800127 275
SW > Operation, with hydr. erection device for WA > bracket II
600 t pulley set on S> head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800119 ........ 260
SW > Operation, with hydr. erection device for WA > bracket II
Slewing platform ballast 70 t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800091 ........ 207
SW > Operation, with hydr. erection device for WA > bracket II
(S> head pulley set _600 t, slewing platform ballast 220 t) . . . . TAB: 12800126 ........ 273
SW > Operation, with hydr. erection device for WA > bracket II (S> head
pulley set _600 t, slewing platform / central ballast 120 / 20 t) . . . . . . . TAB: 12800129 ........ 279
SW > Operation, with hydr. erection device for WA > bracket II
(S head pulley set _600 t, slewing platform ballast 120 t) . . . . TAB: 12800130 ........ 281
SW > Operation, with hydr. erection device for WA > bracket II . . . . . . TAB: 12800092 ........ 209
SW > Operation, with hydr. erection device for WA> bracket II
Slewing platform ballast 170 t . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800087 ........ 199
SW > Operation, with hydr. erection device for WA> bracket II
600 t pulley set on S> head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800117 ........ 256
SW > Operation, with hydr. erection device for WA> bracket II
600 t pulley set on S> head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAB: 12800118 ........ 258
5
ERECTION AND TAKE DOWN CHARTS
6
ERECTION AND TAKE DOWN CHARTS
* = The hook block must be guided in main boom angle range of 0∞ to 20∞ to the horizontal. From the
weight of the hook block on the main boom, no more than max. 5,5 t may be set on the boom.
7
ERECTION AND TAKE DOWN CHARTS
Slewing
platform / Main Permissible weight of hook block on main boom
central ballast boom for equipment configuration
(Equipment
configuration) A B
Crawler 9,1 m¥ 8,8 m Crawler 9,1 m¥ 8,8 m
Supports installed
360∞ via auxiliary 360∞
on supports
support
* = The hook block must be guided in main boom angle range of 0∞ to 20∞ to the horizontal. From the
weight of the hook block on the main boom, no more than max. 5,5 t may be set on the boom.
8
ERECTION AND TAKE DOWN CHARTS
D G
13,0 m ¥ 13,0 m 16,0 m ¥ 12,0 m
13,5 m ¥ 12,9 m
360∞ zur Page
* The hook block must be guided in main boom angle range of 0∞ to 20∞ to the horizontal. From the
weight of the hook block on the main boom, no more than max. 5,5 t may be set on the boom.
9
ERECTION AND TAKE DOWN CHARTS
D G
13,0 m ¥ 13,0 m 16,0 m ¥ 12,0 m
13,5 m ¥ 12,9 m
360∞ to the side
* The hook block must be guided in main boom angle range of 0∞ to 20∞ to the horizontal. From the
weight of the hook block on the main boom, no more than max. 5,5 t may be set on the boom.
10
ERECTION AND TAKE DOWN CHARTS
C E
12,6 m ¥ 12,6 m 16,0 m ¥ 10,5 m
360∞ to the side
* The hook block must be guides in main boom angle range of 0∞ to 20∞ to the horizontal. From the
weight of the hook block on the main boom, no more than max. 5,5 t may be set on the boom.
11
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,0 19,3
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,4 18,7
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 22,8 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
12
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not over sliding section
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,7 19,8 15,6 11,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 19,4 15,4 11,4
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,9 19,1 15,1 11,1
S 56 14,1 18,4 25,0 25,0 25,0 25,0 25,0 25,0 23,5 19,1 14,8
S 63 0,2 1,8 6,5 14,2
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
13
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,1 17,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,9 16,4
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 13,5 19,0 25,0 25,0
Erection of S 49 / W 91, S 49 / 98 und S 56 / W 49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
14
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 16,8 12,9 9,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,1 16,5 12,6 8,8
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,8 16,2 12,4 8,6
S 56 8,6 12,5 21,8 25,0 25,0 25,0 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
15
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 18,3 13,9
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,1 17,7 13,4
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,2 12,9
S 56 18,0 24,9 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,6 12,4
S 63 4,9 6,5 11,4 19,3 25,0
Erection of S 42 / W 98, S 42 / W 105 and S 49 / W 49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position,
16
ERECTION AND TAKE DOWN CHARTS
Erection, take down over supported sprocket, not over sliding section
Aus>
Permissible weight of hook block on W > boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25.0 25.0 25.0 25.0 25.0 25.0 24.7 19.6 15.1 11.0 7.4 3.9
S 42 25.0 25.0 25.0 25.0 25.0 25.0 24.5 19.2 14.8 10.7 7.2 3.7
S 49 12.4 19.9 25.0 25.0 25.0 25.0 24.1 19.2 14.5
S 56 0.8
Erection of S 49 / W 77. S 42 / W 84 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
17
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,8 16,6 12,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,6 16,5 12,5
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,4 16,4 12,4
S 56 15,5 20,2 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,6 16,2 12,2
S 63 1,7 3,6 8,6 16,7 24,0
Erection of S 56 / W 105 and S 63 / W 56 is only possible with unpinned S> head pulley set
Erection of S 42 / W 77, S 42 / W 84 and S 49 / W 35 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
18
ERECTION AND TAKE DOWN CHARTS
Erection, take down over supported sprocket, not over sliding section
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 21,4 16,6 12,4 8,4 5,1 1,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,3 12,1 8,1 4,8 1,5
S 49 6,8 13,7 23,3 25,0 25,0 25,0
Erection of S 49 / W 63 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
19
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 17,9 13,6 10,0 6,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,3 17,7 13,5 9,8 6,3
S 49 17,4 25,0 25,0 25,0 25,0 25,0 25,0 22,5 17,6 13,3 9,8 6,2
S 56 2,3 5,9 14,4 21,9 25,0
Erection of S 49 / W 98, S 49 / W 105 and S 56 / W 56 is only possible with unpinned S> head pulley set
Erection of S 35 / W 77, S 35 / W 84 and S 42 / W 35 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77≥ and SW_67≥ first as SW_87≥ and then luff into the
corresponding position.
20
ERECTION AND TAKE DOWN CHARTS
Erection, take down over supported sprocket, not over sliding section
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 19,2 13,9 9,7 6,1 2,5
S 42 11,4 21,9 25,0 25,0 25,0 18,8
Erection of S 42 / W 63 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77≥ and SW_67≥ first as SW_87≥ and then luff into the
corresponding position.
21
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m before center RDV)
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 21,6 16,2 12,0 8,1 4,6 1,5
S 42 15,4 25,0 25,0 25,0 25,0 21,4 16,3 11,8
Erection of S 42 / W 70, S 42 / W 77 is only possible with unpinned S> head pulley set
is not possible
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
22
ERECTION AND TAKE DOWN CHARTS
Erection, take down over supported sprocket, not over sliding section
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42
S 35 13,7 23,7 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
23
ERECTION AND TAKE DOWN CHARTS
24
ERECTION AND TAKE DOWN CHARTS
25
ERECTION AND TAKE DOWN CHARTS
26
ERECTION AND TAKE DOWN CHARTS
27
ERECTION AND TAKE DOWN CHARTS
28
ERECTION AND TAKE DOWN CHARTS
29
ERECTION AND TAKE DOWN CHARTS
30
ERECTION AND TAKE DOWN CHARTS
31
ERECTION AND TAKE DOWN CHARTS
32
ERECTION AND TAKE DOWN CHARTS
33
ERECTION AND TAKE DOWN CHARTS
34
ERECTION AND TAKE DOWN CHARTS
35
ERECTION AND TAKE DOWN CHARTS
36
ERECTION AND TAKE DOWN CHARTS
37
ERECTION AND TAKE DOWN CHARTS
38
ERECTION AND TAKE DOWN CHARTS
39
ERECTION AND TAKE DOWN CHARTS
40
ERECTION AND TAKE DOWN CHARTS
41
ERECTION AND TAKE DOWN CHARTS
42
ERECTION AND TAKE DOWN CHARTS
43
ERECTION AND TAKE DOWN CHARTS
44
ERECTION AND TAKE DOWN CHARTS
45
ERECTION AND TAKE DOWN CHARTS
46
ERECTION AND TAKE DOWN CHARTS
47
ERECTION AND TAKE DOWN CHARTS
48
ERECTION AND TAKE DOWN CHARTS
49
ERECTION AND TAKE DOWN CHARTS
50
ERECTION AND TAKE DOWN CHARTS
51
ERECTION AND TAKE DOWN CHARTS
52
ERECTION AND TAKE DOWN CHARTS
53
ERECTION AND TAKE DOWN CHARTS
54
ERECTION AND TAKE DOWN CHARTS
55
ERECTION AND TAKE DOWN CHARTS
56
ERECTION AND TAKE DOWN CHARTS
57
ERECTION AND TAKE DOWN CHARTS
58
ERECTION AND TAKE DOWN CHARTS
59
ERECTION AND TAKE DOWN CHARTS
60
ERECTION AND TAKE DOWN CHARTS
61
ERECTION AND TAKE DOWN CHARTS
62
ERECTION AND TAKE DOWN CHARTS
63
ERECTION AND TAKE DOWN CHARTS
64
ERECTION AND TAKE DOWN CHARTS
65
ERECTION AND TAKE DOWN CHARTS
66
ERECTION AND TAKE DOWN CHARTS
67
ERECTION AND TAKE DOWN CHARTS
68
ERECTION AND TAKE DOWN CHARTS
69
ERECTION AND TAKE DOWN CHARTS
70
ERECTION AND TAKE DOWN CHARTS
71
ERECTION AND TAKE DOWN CHARTS
72
ERECTION AND TAKE DOWN CHARTS
73
ERECTION AND TAKE DOWN CHARTS
74
ERECTION AND TAKE DOWN CHARTS
75
ERECTION AND TAKE DOWN CHARTS
76
ERECTION AND TAKE DOWN CHARTS
77
ERECTION AND TAKE DOWN CHARTS
78
ERECTION AND TAKE DOWN CHARTS
79
ERECTION AND TAKE DOWN CHARTS
80
ERECTION AND TAKE DOWN CHARTS
81
ERECTION AND TAKE DOWN CHARTS
82
ERECTION AND TAKE DOWN CHARTS
83
ERECTION AND TAKE DOWN CHARTS
84
ERECTION AND TAKE DOWN CHARTS
85
ERECTION AND TAKE DOWN CHARTS
86
ERECTION AND TAKE DOWN CHARTS
87
ERECTION AND TAKE DOWN CHARTS
88
ERECTION AND TAKE DOWN CHARTS
89
ERECTION AND TAKE DOWN CHARTS
90
ERECTION AND TAKE DOWN CHARTS
91
ERECTION AND TAKE DOWN CHARTS
92
ERECTION AND TAKE DOWN CHARTS
93
ERECTION AND TAKE DOWN CHARTS
94
ERECTION AND TAKE DOWN CHARTS
95
ERECTION AND TAKE DOWN CHARTS
96
ERECTION AND TAKE DOWN CHARTS
97
ERECTION AND TAKE DOWN CHARTS
98
ERECTION AND TAKE DOWN CHARTS
99
ERECTION AND TAKE DOWN CHARTS
100
ERECTION AND TAKE DOWN CHARTS
101
ERECTION AND TAKE DOWN CHARTS
102
ERECTION AND TAKE DOWN CHARTS
103
ERECTION AND TAKE DOWN CHARTS
104
ERECTION AND TAKE DOWN CHARTS
105
ERECTION AND TAKE DOWN CHARTS
106
ERECTION AND TAKE DOWN CHARTS
107
ERECTION AND TAKE DOWN CHARTS
108
ERECTION AND TAKE DOWN CHARTS
109
ERECTION AND TAKE DOWN CHARTS
110
ERECTION AND TAKE DOWN CHARTS
111
ERECTION AND TAKE DOWN CHARTS
112
ERECTION AND TAKE DOWN CHARTS
113
ERECTION AND TAKE DOWN CHARTS
114
ERECTION AND TAKE DOWN CHARTS
115
ERECTION AND TAKE DOWN CHARTS
116
ERECTION AND TAKE DOWN CHARTS
117
ERECTION AND TAKE DOWN CHARTS
118
ERECTION AND TAKE DOWN CHARTS
119
ERECTION AND TAKE DOWN CHARTS
120
ERECTION AND TAKE DOWN CHARTS
Slewing Main boom Permissible weight of hook block on main boom for
platform> / equipment configuration
central ballast
C E F
12,6 m ¥ 12,6 m 16,0 m ¥ 10,5 m 16,0 m ¥ 10,5 m
121
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥13,0 m) with installed crawler carriers
(Support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 17,4
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 13,4 19,3 25,0 25,0
Erection, take down to the front or rear on supports (16,0 m ¥12,0 m) with installed crawler carriers
(Support points 6,0 m in front of center RDV) equipment configuration H
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,7 19,3 15,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,4 19,0 14,8
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 18,8 14,6
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 18,5 14,3
S 63 6,4 8,4 13,8 22,2 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
122
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 8,0 m in front of RDV) equipment configuration G
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,0 19,3
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,4 18,7
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 22,8 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
123
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(StÂtzpunkte 6,3 m vor Mitte RDV) RÂstzustand C
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,6 19,8 15,7 11,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 19,5 15,4 11,5
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,0 19,2 15,2 11,3
S 56 13,9 18,3 25,0 25,0 25,0 25,0 25,0 25,0 23,7 19,3 15,0
S 63 1,8 6,6 14,3
Erection, take down to the front or rear on supports (16,0 m ¥ 10,6 m) without installed crawler carrier
(Support points 5,25 m in front of center of RDV) equipment configuratoin F
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,9 19,1 14,6 10,8 7,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,5 18,7 14,3 10,6 6,9
S 49 20,3 25,0 25,0 25,0 25,0 25,0 25,0 23,4 18,4 13,9 10,3 6,6
S 56 4,5 8,1 16,7 24,0 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
124
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,6 m) without installed crawler carrier
(Support points 8,0 m in front of center of RDV) equipment configuration E
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,5 19,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,3 18,7
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 22,3 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
125
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(Support points 6,5 m in front of center of RDV) equipment configuration D
Aus>
Permissible weight of hook block on W > boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,4 19,0 14,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,1 18,8 14,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 18,6 14,4
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,9 18,3 14,1
S 63 5,9 7,9 13,3 21,7 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 6,0 m in front of center of RDV) equipment configuration H
Aus>
Permissible weight of hook block on W > boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,6 16,4 12,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,3 16,2 12,1
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,8 20,0 15,9 11,9
S 56 15,4 20,0 25,0 25,0 25,0 25,0 25,0 25,0 24,5 20,0 15,6 11,6
S 63 1,4 3,2 8,0 15,9 23,2
Erection of S 56 / W 105 and S 63 / W 56 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
126
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 8,0 m in front of center of RDV) equipment configuration G
Aus>
Permissible weight of hook block on W > boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,1 17,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,9 16,4
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 13,5 19,0 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
127
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(Support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,2 16,6 12,7 8,9
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,9 16,3 12,5 8,7
S 49 24,4 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,6 16,1 12,3 8,5
S 56 8,1 12,0 21,2 25,0 25,0 25,0 25,0 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 10,6 m) without installed crawler carrier
(Support points 5,25 m in front of center of RDV) equipment configuration F
Boom
Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,5 15,9 11,7 8,1 4,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,1 15,6 11,4 7,8 4,3
S 49 14,0 21,7 25,0 25,0 25,0 25,0 25,0 20,0 15,3 11,0
S 56 2,2 10,1
Erection of S 49 / W 84, S 49 / W 91 and S 56 / W 42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
128
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) with installed crawler carrier
(Support points 8,0 m in front of RDV) equipment configuration E
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,6 20,2 15,9
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 20,0 15,8
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,2 19,9 15,7
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 19,7 15,0
S 63 7,8 10,1 15,7 24,4 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
129
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 16,9 13,0 9,2
S>42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,7 12,8 9,0
S>49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0 16,4 12,6 8,8
S>56 8,6 12,6 22,0 25,0 25,0 25,0 25,0 25,0
Erection, take down to the front or to the rear on supports (16,0 m ¥ 12,0 m) with installed crawler
carriers (support points 6,0 m in front of center of RDV) equipment configuration H
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,6 18,8 14,4 10,6 6,9
S>42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,2 18,5 14,1 10,4 6,7
S>49 19,6 25,0 25,0 25,0 25,0 25,0 25,0 23,2 18,2 13,8 10,2 6,5
S>56 4,0 7,6 16,2 23,5 25,0 25,0
Erection of S 49 / W 105 and S 56 / W 63 is only possible with unpinned S> boom pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
130
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(Support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 18,3 13,9
S>42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,1 17,7 13,4
S>49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,2 12,9
S>56 18,0 24,9 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,6 12,4
S>63 4,9 6,5 11,4 19,3 25,0
Erection of S 56 / W 77 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
131
ERECTION AND TAKE DOWN CHART
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(Support points 6,3 m before center of RDV) equipment configuration C
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,7 14,4 10,3 6,8 3,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,6 18,4 14,1 10,0 6,6 3,2
S 49 10,6 18,0 25,0 25,0 25,0 25,0 23,3 18,5
Erection of S 49 / W 70 and S 49 / W 77 is only possible with unpinned S> head pulley set
Erection, take down to the front or rear on supports (16,0 m ¥ 10,5 m) without installed crawler carrier
(Support points 5,25 m before center of RDV) equipment configuration F
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 23,9 18,1 13,6 9,6 5,8 2,7
S 42 20,3 25,0 25,0 25,0 25,0 23,4 18,0 13,2 9,3 5,5 2,4
S 49 1,3 7,4 16,8
Erection of S 42 / W 91, S 42 / W 98 and S 49 / W 42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
132
ERECTION AND TAKE DOWN CHART
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) without installed crawler carrier
(Support points 8,0 m before center RDV) equipment configurationE
Aus>
Permissible weight of hook block on W > boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,4 13,5 9,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 17,2 13,4 9,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,7 17,1 13,3 9,5
S 56 9,3 13,5 23,0 25,0 25,0 25,0 25,0 25,0 21,4
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
133
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(Support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 24,0 19,0 14,6 10,5 7,0 3,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,9 18,7 14,3 10,2 6,8 3,4
S 49 11,0 18,5 25,0 25,0 25,0 25,0 23,6 18,7
Erection, take down to the front or rear on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 6,0 m in front of center of RDV) equipment configuration H
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 21,1 16,3 12,1 8,2 4,8 1,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 21,0 16,0 11,8 7,9 4,6 1,4
S 49 6,1 12,9 22,6 25,0 25,0
Erection of S 42 / W 105 und S 49 / W 56 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
134
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carrier
(Support points 8,0 m before center of RDV) equipment configuration G
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,4 13,5 9,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 17,2 13,4 9,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,7 17,1 13,3 9,4
S 56 9,3 13,5 23,1 25,0 25,0 25,0 25,0 25,0 21,4
Erection of S 56 / W 77 und S 56 / W 84 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77≥ and SW_67≥ first as SW_87≥ and then luff into the
corresponding position
135
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12.6 m ¥ 12.6 m) without installed crawler carrier
(Support points 6.3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25.0 25.0 25.0 25.0 25.0 21.0 15.6 11.3 7.5 3.9 0.9
S>42 14.5 25.0 25.0 25.0 25.0 20.6 15.5
Erection, take down to the front or to the rear on supports (16.0 m ¥ 10.5 m) without installed crawler
carrier
(Support points 5.25 m in front of center of RDV) equipment configuration F
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25.0 25.0 25.0 25.0 21.6 15.6 10.6 6.8 3.3
S>42 4.6 14.4
Erection of S 35 / W 84 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
136
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) without installed crawler carrier
(Support points 6,0 m in front of center of RDV) equipment configuration E
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 25,0 23,5 18,6 14,3 10,3 6,8 3,5
S>42 25,0 25,0 25,0 25,0 25,0 25,0 23,5 18,4 14,1 10,1 6,7 3,4
S>49 10,1 17,6 25,0 25,0 25,0 25,0 23,4
Erection of S 49 / W 70 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
137
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(Support points 6,5 m in front of center of RDV) equipment configuration D
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 21,2 15,7 11,4 7,6 4,1 1,0
S 42 14,8 25,0 25,0 25,0 25,0 20,8 15,7
Erection, take down to the front or rear on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 6,0 m in front of center of RDV) equipment configuration H
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 24,5 18,3 13,1 9,0 5,4 2,0
S 42 9,5 19,9 25,0 25,0 24,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
138
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 8,0 m in front of center of RDV) equipment configuration G
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,5 18,6 14,3 10,3 6,8 3,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,6 18,4 14,2 10,1 6,7 3,4
S 49 10,1 17,6 25,0 25,0 25,0 25,0 23,4
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
139
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m)without installed crawler carrier
(Support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 20,5 25,0 25,0 23,4 17,5 12,0
Erection of S 35 / W 56 und S 35 / W 63 is only possible with unpinned S> head pulley set
Erection, take down to the front or rear on supports (16,0 m ¥ 10,5 m) without installed crawler carrier
(Support points 5,25 m in front of center of RDV) equipment configuration F
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 9,4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
140
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) without installed crawler carrier
(Support points 8,0 m in front of center of RDV) equipment configuration E
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 19,6 14,3 10,2 6,6 3,1
S 42 11,4 22,3 25,0 25,0 25,0 19,3
Erection of S 42 / W 46 and S 42 / W 63 is only possible with unpinned S> head pulley set
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
141
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(Support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 6,0 m in front of center of RDV) equipment configuration H
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,8 20,2
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,5 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
142
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(Support points 8,0 m in front of center of RDV) equipment configuration G
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position,
143
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(StÂtzpunkte 6,3 m in front of center of RDV) equipment configuration C
Boom
Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,4 17,1
S 42 2) 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,2 16,8
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,9 16,6
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 12,4 18,1 25,0 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 10,5 m) without installed crawler
carrier (Support points 5,25 m in front of center of RDV) equipment configuration F
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 20,8 16,6 12,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 20,4 16,3 12,2
S 49 2) 25,0 25,0 25,0 25,0 25,0 25,0 20,1 16,0 12,0
S 56 25,0 25,0 25,0 25,0 25,0 24,6 20,1 15,7 11,7
S 63 8,4 16,2 23,4
Erection of S 56 / W 105is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
144
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(Support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
145
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without installed crawler carrier
(Support points 6,3 m in front of center of RDV)
Operating
Boom Permissible weight of hook block on W > boom head
mode
[m] [t]
SW W 28
77∞ S 35 25,0
67∞ S 42 25,0
S 49 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 10,5 m) without installed crawler
carrier (Support points 5,25 m in front of center of RDV)
Operating
Boom
mode Permissible weight of hook block on W > boom head
[m] [t]
SW W 28 W 35 W 42 W 49
S 35 25,0 25,0 25,0 25,0
77∞ S 42 25,0 25,0 25,0
67∞ S 49 25,0 25,0 25,0
S 56 15,9 20,4 25,0
S 63 1,8 3,5
Note: The boom and support combinations listed on this page have no load chart in area Sw 87∞.
Erection:
a.) Erect the S> boom in corresponding working angle (77∞ or 67∞), the W> boom hangs down
as far as possible.
b.) Erect the W> boom into the corresponding working position.
146
ERECTION AND TAKE DOWN CHARTS
200 S 98 16,0
140 S 98 7,5
147
ERECTION AND TAKE DOWN CHARTS
180 S 98 16,0
120 S 98 7,5
148
ERECTION AND TAKE DOWN CHARTS
149
ERECTION AND TAKE DOWN CHARTS
140 S 98 16,0
100 S 98 7,5
150
ERECTION AND TAKE DOWN CHARTS
200 S 98 16,0
140 S 98 7,5
151
ERECTION AND TAKE DOWN CHARTS
180 S 98 16,0
120 S 98 7,5
152
ERECTION AND TAKE DOWN CHARTS
150 S 98 16,0
110 S 98 7,5
153
ERECTION AND TAKE DOWN CHARTS
140 S 98 16,0
100 S 98 7,5
154
ERECTION AND TAKE DOWN CHARTS
90 SL 84 16,0
40 84 7,5
130 SL 91 16,0
70 91 7,5
170 SL 98 16,0
110 98 7,5
155
ERECTION AND TAKE DOWN CHARTS
80 SL 84 16,0
40 SL 84 7,5
110 SL 91 16,0
60 SL 91 7,5
150 SL 98 16,0
100 SL 98 7,5
156
ERECTION AND TAKE DOWN CHARTS
70 SL 84 16,0
30 SL 84 7,5
90 SL 91 16,0
50 SL 91 7,5
130 SL 98 16,0
80 SL 98 7,5
157
ERECTION AND TAKE DOWN CHARTS
70 SL 84 16,0
30 SL 84 7,5
90 SL 91 16,0
50 SL 91 7,5
110 SL 98 16,0
80 SL 98 7,5
158
ERECTION AND TAKE DOWN CHARTS
90 SL 84 16,0
40 84 7,5
130 SL 91 16,0
70 91 7,5
170 SL 98 16,0
110 98 7,5
159
ERECTION AND TAKE DOWN CHARTS
80 SL 84 16,0
40 SL 84 7,5
110 SL 91 16,0
60 SL 91 7,5
150 SL 98 16,0
100 SL 98 7,5
160
AUFRICHT> UND ABLEGETABELLEN
70 SL 84 16,0
30 SL 84 7,5
90 SL 91 16,0
50 SL 91 7,5
130 SL 98 16,0
80 SL 98 7,5
161
ERECTION AND TAKE DOWN CHARTS
162
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90∞ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
163
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90≥ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
164
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90≥ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
165
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90≥ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
166
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90∞ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
167
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90∞ ewquired (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab, 12800098
168
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12∞ to 90∞
b) Erection, take down with W> boom angle to S> boom 90∞ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab, 12800098
169
ERECTION AND TAKE DOWN CHARTS
Note: a) Erection, take down with W> boom angle to S> boom 12≥ to 90≥
b) Erection, take down with W> boom angle to S> boom 90≥ required (W> boom hangs
downward)
Systems with pulley set on S> head need additional ballasting according to chart:
Tab. 12800098
170
ERECTION AND TAKE DOWN CHARTS
D: 13,0 m x 13,0 m, crawlers installed, working range 360∞, crawler track pad width 1,5 m
or 13,5 m x 12,9 m, crawlers installed, working range 360∞, crawler track pad width 2,0 m
G: 16,0 m x 12,0 m, crawlers installed, working range to the side
H: 16,0 m x 12,0 m, crawlers installed, working range 360∞
Slewing Main boom Permissible weight of hook block on main boom for
platform / equipment configuration:
central ballast
D G H
13,0 m x 13,0 m 16,0 m x 12,0 m 16,0 m x 12,0 m
13,5 m x 12,9 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
250/20 28 16,0 > >
in Sonder> 35 > 84 16,0 16,0 16,0
position 91 14,5 14,5 14,5
98 10,0 10,0 10,0
105 6,5 6,5 6,5
112 3,0 3,0 3,0
245/20 28 > 84 16,0 16,0 16,0
91 14,5 14,5 14,5
98 10,0 10,0 10,0
105 6,5 6,5 6,5
112 3,0 3,0 3,0
220/20 28 > 84 16,0 16,0 16,0
91 14,5 14,5 14,0
98 10,0 10,0 10,0
105 6,5 6,5 6,5
112 3,0 3,0 3,0
171
ERECTION AND TAKE DOWN CHARTS
D: 13,0 m x 13,0 m, crawlers installed, working range 360∞, crawler track pad width 1,5 m
or 13,5 m x 12,9 m, crawlers installed, working range 360∞, crawler track pad width 2,0 m
G: 16,0 m x 12,0 m, crawlers installed, working range to the side
H: 16,0 m x 12,0 m, crawlers installed, working range 360∞
Slewing Main boom Permissible weight of hook block on main boom for
platform> / equipment configuration:
central ballast
D G H
13,0 m x 13,0 m 16,0 m x 12,0 m 16,0 m x 12,0 m
13,5 m x 12,9 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
170/20 28 > 84 16,0 16,0 16,0
91 14,5 14,5 12,5
98 10,0 10,0 8,5
105 6,5 6,5 4,5
112 3,0 3,0 1,1
120/20 28 > 70 16,0 16,0 16,0
77 16,0 16,0 14,5
84 12,0 16,0 9,5
91 8,0 14,5 6,0
98 4,0 10,0 2,0
105 > 6,5 >
112 > 3,0 >
70/20 28 > 63 16,0 16,0 16,0
70 13,5 16,0 10,5
77 8,5 16,0 6,0
84 4,5 11,0 2,0
91 1,1 7,0 >
98 > 3,5 >
172
ERECTION AND TAKE DOWN CHARTS
Slewing Main boom Permissible weight of hook block on main boom for
platform> / equipment configuration:
central ballast
C E F
12,6 m x 12,6 m 16,0 m x 10,5 m 16,0 m x 10,5 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
250 56 > 63 16,0 > >
in Sonder> 70 > 84 16,0 16,0 16,0
position 91 14,5 14,5 14,5
98 10,0 10,0 10,0
105 6,5 6,5 6,5
112 3,0 3,0 3,0
245 28 > 84 16,0 16,0 16,0
91 14,5 14,5 13,0
98 10,0 10,0 9,0
105 6,5 6,5 5,0
112 3,0 3,0 1,1
220 77 16,0 16,0 16,0
84 16,0 16,0 14,0
91 14,5 14,5 10,0
98 10,0 10,0 6,0
105 6,5 6,5 2,5
112 3,0 3,0 >
173
ERECTION AND TAKE DOWN CHARTS
Slewing Main boom Permissible weight of hook block on main boom for
platform> / equipment configuration:
central ballast
C E F
12,6 m x 12,6 m 16,0 m x 10,5 m 16,0 m x 10,5 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
170 28 > 70 16,0 16,0 16,0
77 16,0 16,0 11,5
84 12,0 16,0 7,5
91 8,0 14,5 3,5
98 4,0 10,0 >
105 > 6,5 >
112 > 3,0 >
120 28 > 56 16,0 16,0 16,0
63 16,0 16,0 13,5
70 13,5 16,0 8,5
77 8,5 16,0 4,0
84 4,5 11,0 >
91 1,1 7,0 >
98 > 3,0 >
70 28 > 42 16,0 16,0 16,0
49 16,0 16,0 15,5
56 14,5 16,0 9,0
63 9,0 16,0 4,5
70 4,0 11,0 >
77 > 6,5 >
84 > 2,5 >
174
ERECTION AND TAKE DOWN CHARTS
A: 9,1 m x 8,8 m
B: 9,1 m x 8,8 m, supports installed
Slewing Main boom Permissible weight of hook block on main boom for
platform / equipment configuration:
central ballast
A B
Crawlers 9,1 m x 8,8 m Crawlers 9,1 m x 8,8 m
Supports installed
360∞ via auxiliary 360∞ via auxiliary
support support
[t/t] [m] [t] [t] [t]
245/95 (A) 28 > 84 16,0 16,0 16,0 see
245/20 (B) 91 14,0 14,5 14,0 chart for
98 9,5 10,0 9,5 supported
105 6,0 6,5 6,0 condition
112 2,5 3,0 2,5 TAB 12800065
220/95 (A) 28 > 77 16,0 16,0 16,0
220/20 (B) 84 15,5 16,0 15,5
91 11,0 14,5 11,0
98 7,0 10,0 7,0
105 3,5 6,5 3,5
112 > 3,0 >
170/95 (A) 28 > 70 16,0 16,0 16,0
170/20 (B) 77 13,5 16,0 13,5
84 9,0 16,0 9,0
91 5,0 14,5 5,0
98 1,1 10,0 1,1
105 > 6,5 >
112 > 3,0 >
175
ERECTION AND TAKE DOWN CHARTS
A: 9,1 m x 8,8 m
B: 9,1 m x 8,8 m, supports installed
Slewing Main boom Permissible weight of hook block on main boom for
platform / equipment configuration:
central ballast
C B
Crawlers 9,1 m x 8,8 m Crawlers 9,1 m x 8,8 m
Supports installed
360∞ via auxiliary 360∞ via auxiliary
support support
[t/t] [m] [t] [t] [t]
170/45 (A) 28 > 63 16,0 16,0 see
70 15,5 16,0 chart for
77 11,0 16,0 supported
84 6,5 16,0 TAB 12800065
91 3,0 14,5
98 > 10,0
105 > 6,5
112 > 3,0
120/45 (A) 28 > 56 16,0 16,0 16,0
120/20 (B) 63 13,0 16,0 13,0
70 8,0 16,0 8,0
77 3,5 16,0 3,5
84 > 15,5 >
91 > 11,0 >
98 > 6,5 >
105 > 3,0 >
176
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA> bracket II TAB: 12800076
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 245 / 95 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 245 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,8 19,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,3 18,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 12,9 18,8 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Due to the added weight, the compbinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8m.
Erection of S 49 / W 98 and S 56 / W 56 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
177
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA> bracket II TAB: 12800076
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 245 / 95 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 245 / 20 t
Erection, take down via supported sprocket (not over sliding section)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,7 19,8 15,7 11,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 19,5 15,4 11,4
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,9 19,1 15,1 11,1
S 56 10,4 14,8 24,8 25,0 25,0 25,0 25,0 25,0 23,5
S 63 0,4 5,1
Erection of S 56 / W 84, S 63 / W 35 and S 63 / W 42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
178
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA > bracket II TAB: 12800077
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 220 / 95 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 220 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,9 17,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,4 16,9
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,8 16,3
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 7,4 9,4 15,0 23,7 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8m.
Erection of S 49 / W 77. S 56 / W 35 and S 56 / W 42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
179
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA > bracket II TAB: 12800077
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 220 / 95 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 220 / 20 t
Erection, take down via supported sprocket (not over sliding section )
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,6 16,9 13,0 9,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,2 16,6 12,7 8,9
S 49 21,6 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,8 16,2 12,4 8,6
S>56 5,0 8,9 18,2 25,0 25,0 25,0
Erection of S 56 / W 63 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
180
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA bracket II TAB: 12800078
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
A: auf Raupen 9,1 m x 8,8 m
Slewing platform / central ballast 170 / 95 t
B: auf Raupen 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 170 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 18,2 13,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,6 13,3
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 17,0 12,7
S 56 16,2 20,8 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,1 16,5
S 63 0,8 2,5 7,4 15,5 25,0
Erection of S 56 / W 98und S 63 / W 56is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Due to the added weight, the compbinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8m.
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
181
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA bracket II TAB: 12800078
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 170 / 95 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 170 / 20 t
Erection, take down via supported sprocket (not over sliding section)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 24,8 19,7 15,2 11,0 7,5 4,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 24,6 19,3 14,9 10,7 7,2 3,7
S 49 8,8 16,3 25,0 25,0 25,0 25,0 24,1
Erection of S 49 / W 63 und S 49 / W 70 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
182
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (Support points 8,0 m vor Mitte RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,9 16,8 12,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,7 16,6 12,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,5 16,5 12,5
S 56 12,0 16,8 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,6
S 63 0,4 2,3 7,4 15,6
Erection of S 56 / W 91, S 63 / W 28 to W 56 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Erection of S 42 / W 63and S 42 / W 70 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
183
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket (not over sliding section)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 21,5 16,7 12,5 8,5 5,1 1,8
S 42 23,7 25,0 25,0 25,0 25,0 25,0 21,4 16,3 12,1 8,2 4,8
S 49 3,2 10,1 20,3 25,0
Erection of S 42 / W 98and S 49 / W 49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
184
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA bracket II TAB: 12800080
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 120 / 45 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 120 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook blockon W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 18,1 13,8 10,1 6,5
S>42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,5 17,9 13,6 10,0 6,4
S>49 14,0 22,5 25,0 25,0 25,0 25,0 25,0 22,6 17,6
S>56 1,0 2,5 13,2
Erection of S 49 / W 84, S 56 / W 28 und S 56 / W 42 is only possible with unpinned S> head pulley set
Erection of S 35 / W 63und S 35 / W 70 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
185
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA bracket II TAB: 12800080
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
A: on crawlers 9,1 m x 8,8 m
Slewing platform / central ballast 120 / 45 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
Slewing platform / central ballast 120 / 20 t
Erection, take down via supported sprocket (not over sliding section)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S>35 25,0 25,0 25,0 25,0 25,0 19,3 14,0 9,8 6,1 2,6
S>42 7,9 18,9 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position. .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
186
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA bracket II TAB: 12800081
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
A: on crawlers 9,1 m x 8,8 m
slewing platform / central ballast 70 / 20 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
slewing platform / central ballast 70 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 25,0 21,9 16,4 12,1 8,3 4,7 1,7
S 42 12,2 23,9 25,0 25,0 25,0
is not possible
Note: Erect operating modes SW 77≥ and SW 67≥ first as SW 87≥ and then luff to the
corresponding position.
187
ERECTION AND TAKE DOWN CHARTS
SW > Operation with hydr. erection device for WA> bracket II TAB: 12800081
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
A: on crawlers 9,1 m x 8,8 m
slewing platform / central ballast 70 / 20 t
B: on crawlers 9,1 m x 8,8 m; with installed supports
slewing platform / central ballast 70 / 20 t
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28
S 35 12,5
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
188
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
Support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,1 17,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,9 17,5
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,6 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 7,5 9,9 15,8 24,9 25,0
Erection, take down to the front or the rear on supports (16,0 m x 12,0 m) with installed crawler
carriers, Support points 6,0 m in front of center of RDV (equipment configuration H)
Boom
Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,8 19,4 15,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,4 19,1 14,9
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,1 18,8 14,6
S 56 17,5 22,6 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 18,5 14,3
S 63 2,8 4,8 10,2 18,9 25,0
Erection of S 56 / W 105 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77≥ and SW 67≥ first as SW 87≥ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8m.
189
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,8 19,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,3 18,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 12,9 18,8 25,0 25,0
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
Note: During the movement on the ground (W> jib in rolling cart). the force in the W 1> guying
(test point 2) must be limited as follows:
190
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carriers,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,7 19,9 15,7 11,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,4 19,6 15,5 11,5
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,1 19,2 15,3 11,3
S 56 10,3 14,8 24,9 25,0 25,0 25,0 25,0 25,0 23,7
S 63 0,5 5,3
Erection of S 56 / W 84, S 63 / W 35 and S 63 / W 42 is only possible with unpinned S> head pulley set
Erection, take down to the front or rear on supports (16,0 m x 10,5 m) without crawler carriers,
support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,0 19,1 14,7 10,9 7,2
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,5 18,8 14,3 10,6 6,9
S 49 16,7 25,0 25,0 25,0 25,0 25,0 25,0 23,4 18,4 13,9 10,3
S 56 0,8 4,4 13,1 22,9
Erection of S 49 / W 91, S 49 / W 98 and S 56 / W 49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
191
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,6 19,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,3 18,6
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 12,7 18,8 25,0 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
192
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports ( 13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,5 19,1 14,9
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,2 18,9 14,7
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,8 18,6 14,4
S 56 16,9 21,9 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,9 18,3 14,2
S 63 2,3 4,4 9,8 18,4 25,0
Erection of S 56 / W 105 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position,
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m.
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed crawler
carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,7 16,5 12,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,3 16,2 12,2
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,9 20,0 16,0 11,9
S 56 11,8 16,4 25,0 25,0 25,0 25,0 25,0 25,0 24,5 20,1
S 63 1,8 6,7 14,7
Erection of S 56 / W 91, S 63 / W 35 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
193
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,9 17,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,4 16,9
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,8 16,3
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 7,4 9,4 15,0 23,7 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
194
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports ( 12,6 m x 12,6 m) without crawler carriers,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,7 12,8 9,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0 16,4 12,6 8,8
S 49 20,9 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,7 16,1 12,3 8,5
S 56 4,5 8,4 17,7 25,0 25,0 25,0
Erection of S 49 / W 105 und S 56 / W 63is only possible with unpinned S> head pulley set
Erection, take down to the front or to the rear on supports ( 16,0 m x 10,5 m)
without crawler carriers, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,5 16,0 11,7 8,1 4,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,1 15,6 11,4 7,9 4,4
S 49 10,4 18,1 25,0 25,0 25,0 25,0 25,0
S 56 0,8
Erection of S 49 / W 70 und S 56 / W 35 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
195
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports ( 16,0 m x 10,5 m) without crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,7 20,3 16,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,5 20,1 15,9
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 20,0 15,8
S 56 18,0 24,4 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 19,8 15,0
S 63 4,3 6,6 12,3 21,2 25,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position,
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
196
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,7 17,0 13,1 9,3
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,4 16,7 12,9 9,1
S 49 21,5 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,1 16,5 12,7 8,9
S 56 5,0 9,1 18,5 25,0 25,0 25,0
Erection, take down to the front or the rear on supports (16,0 m x 12,0 m)
with installed crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,9 14,5 10,7 7,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,3 18,6 14,2 10,5 6,8
S 49 16,1 24,6 25,0 25,0 25,0 25,0 25,0 23,3 18,3 13,8
S 56 0,4 4,0 12,6 22,4
Erection of S 49 / W 91 und 56/ W49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
197
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 18,2 13,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,6 13,3
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 17,0 12,7
S 56 16,2 20,8 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,1 16,5
S 63 0,8 2,5 7,4 15,5 25,0
Erection of S 56 / W 98 und S 63 / W 56 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal, The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows :
198
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carriers,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,8 18,8 14,5 10,4 6,9 3,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,5 14,2 10,1 6,7 3,3
S 49 7,0 14,5 24,9 25,0 25,0 25,0
Erection of S 49 / W 56 and S 49 / W 63 is only possible with unpinned S> head pulley set
Erection, take down to the front or the rear on supports (16,0 m x 10,5 m)
without crawler carriers, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 24,0 18,2 13,7 9,7 5,9 2,7
S 42 16,8 25,0 25,0 25,0 25,0 23,5 18,1 13,3
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
199
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (12,6 m x 12,6 m) without crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,2 17,6 13,6 9,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,4 13,5 9,7
S 49 22,3 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 17,2 13,4 9,6
S 56 5,8 10,0 19,7 25,0 25,0 25,0 25,0
Erection of S 56 / W 63 and S 56 / W 70 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff into the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
200
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 24,1 19,1 14,7 10,6 7,1 3,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 24,0 18,8 14,4 10,3 6,9 3,5
S 49 7,5 15,0 25,0 25,0 25,0 25,0
Erection of S 49 / W 63 is only possible with unpinned S> head pulley set
Erection, take down to the front or the rear on supports (16,0 m x 12,0 m) with installed crawler
carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 21,2 16,4 12,2 8,3 4,9 1,6
S 42 22,8 25,0 25,0 25,0 25,0 25,0 21,1 16,1 11,9 7,9 4,7
S 49 2,6 9,4 21,4
Erection of S 42 / W 91, S 42 / W 98 and S 49 / W 42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
201
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,6 13,7 9,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,0 17,4 13,5 9,7
S 49 22,3 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 17,2 13,2 9,2
S 56 5,9 10,1 19,7 25,0 25,0 25,0 25,0
Erection of S 56 / W 63 and S 56 / W 70 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
202
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carriers,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 21,1 15,7 11,4 7,6 4,0 1,0
S 42 11,2 22,6 25,0 25,0 25,0
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m)
without crawler carriers, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 21,7 15,7 10,7
S 42 3,3
Erection of S 35 / W 70 und S 42 / W 28 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
203
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,8 14,5 10,4 7,0 3,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,6 14,3 10,2 6,9 3,5
S 49 6,7 14,3 24,8 25,0 25,0
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
204
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 21,3 15,8 11,6 7,8 4,2 1,1
S 42 11,5 22,9 25,0 25,0 25,0
Erection, take down to the front or to the rear on supports (13,0 m x 13,0 m) with installed crawler
carriers support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 24,7 18,4 13,2 9,1 5,5 2,0
S 42 6,1 17,0 25,0
Erection of S 35 / W 91 und 42/ W42 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
205
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (13,0 m x 13,0 m) with installed crawler carriers
support points 8,0 m in front of center of RDV (Equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,7 18,8 14,5 10,4 7,0 3,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,8 18,6 14,3 10,3 6,9 3,5
S 49 6,8 14,3 24,9 25,0 25,0
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
206
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 17,4 25,0 25,0
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m)
without crawler carrier support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
207
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 19,8 14,5 10,4 6,8 3,3
S 42 8,3 19,6 25,0 25,0
Note: Erect operating modes SW 77≥ and SW 67≥ first as SW 87≥ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
208
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II TAB: 12800092
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Ballast on slewing platform extension 250 t
Central ballast 20 t
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed crawler
carriers support points 6,5 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 20,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,8 20,3
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,5 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
209
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II TAB: 12800092
without / with 400 t pulley set on S> head System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Slewing platform extension 250 t
Central ballast 20 t
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers
support points 8,0 m in front of center of RDV (Equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: Erect operating modes SW 77≥ and SW 67≥ first as SW 87≥ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows :
210
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II TAB: 12800093
(SW = 87!) System: S 2826.20
without / with 400 t pulley set on S> head W 2421.10
W 2421.8
Page 1 of 3
Ballast on slewing platform extension 250 t
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,5 17,2
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,3 16,9
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0 16,7
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 6,5 8,8 14,6 23,6 25,0
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m)
without crawler carrier support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 20,8 16,6 12,6
S 42 25,0 25,0 25,0 25,0 25,0 25,0 20,5 16,3 12,3
S 49 25,0 25,0 25,0 25,0 25,0 25,0 20,1 16,0 12,0
S 56 25,0 25,0 25,0 25,0 25,0 24,6 20,1
S 63 4,7 14,9
Erection of S 56 / W 91 und S 63 / W 49 is only possible with unpinned S> head pulley set
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
211
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II TAB: 12800093
(SW = 87!) System: S 2826.20
without / with 400 t pulley set on S> head W 2421.10
W 2421.8
Page 2 of 3
Ballast on slewing platform extension 250 t
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0
S 49 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 17,0
S 56 18,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 20,0 15,0
S 63 10,0 15,0 25,0 25,0 25,0
Note: Erect operating modes SW 77∞ and SW 67∞ first as SW 87∞ and then luff to the
corresponding position.
Due to the added weight, the combinations S 56 / W 105 and S 63 / W 56must be supported
with an auxiliary crane when moving the main boom between 0∞ to 7∞ to the horizontal. The
minimum power of the auxiliary crane is 4 t at a lifting height of 8 m .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
212
ERECTION AND TAKE DOWN CHARTS
SW > Operation, with hydr. erection device for WA > bracket II TAB: 12800093
(SW = 77∞ / SW 67∞) System: S 2826.20
without / with 400 t pulley set on S> head W 2421.10
W 2421.8
Page 3 of 3
Ballast on slewing platform extension 250 t
Erection, take down to the side on supports (16.0 m x 10.5 m) without crawler carrier
support points 8.0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28
S 35 25.0
S 42 25.0
S 49 25.0
S 56 12.2
S 63 0.4
Erection, take down to the side on supports (16.0 m x 10.5 m) without crawler carrier
support points 8.0 m in front of center of RDV (Equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49
S 35 25.0 25.0 25.0 25.0
S 42 25.0 25.0 25.0
S 49 25.0 25.0 25.0
S 56 12.2 16.8 25.0
S 63 0.4 2.1
Note: The boom and support combinations shown on this page have no load charts in the area of
SW 87∞.
Erection procedure:
a) Erect the S> boom in the corresponding working angle (77∞ or 67∞). The W> boom hangs
down as far as possible.
b) Erect the W> boom into the correspoinding working position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
213
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA > bracket II
Derrick ballast R = 13 m TAB: 12800094
600 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Derrick boom D = 31,5 m; R = 13,0 m
Slewing platform
Equipment configuration Central ballast
ballast
[t]
[t]
A: on crawlers 9,1¥8,8 m 220 95
B: on crawlers 9,1¥8,8 m
220 20
with installed supports
C: on supports 12,6¥12,6 m 220 >>
D: on supports 13,0¥13,0 m
(bzw, 13,5¥12,9 m) 220 20
with installed crawler carriers
Boom Derrick
Permissible Procedure
ballast
weight of hook
block[t]
[m] [t]
S 35 / W 14 16,0 >> a)
W 14 11,0 >> a)
W 14 7,0 >> a)
S 42 / W 14 16,0 30 a)
W 14 11,0 10 a)
W 14 7,0 >> a)
S 49 / W 14 16,0 80 a)
W 14 11,0 50 a)
W 14 7,0 40 a)
S 56 / W 14 16,0 130 a)
W 14 11,0 100 a)
W 14 7,0 80 a)
S 63 / W 14 16,0 180 a)
W 14 11,0 150 a)
W 14 7,0 130 a)
S 70 / W 14 16,0 240 a)
W 14 11,0 210 a)
W 14 7,0 180 a)
214
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA > bracket II
Derrick ballast R = 13 m TAB: 12800094
W with 400 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Derrick boom D = 31,5 m; R = 13,0 m
Procedure: a) Erection, take down with W> boom: Angle to S> boom 12∞> 90∞
b) Erection, take down with W> boom: Angle to S> boom 90∞ required
(W> boom hangs down)
Note: Systems with pulley set on S> head need additional ballasting per chart 12800098
215
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA bracket II
Derrick ballast R = 15 m TAB: 12800095
600 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Derrick boom D = 31,5 m; R = 13,0 m
216
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA bracket II
Derrick ballast R = 15 m TAB: 12800095
600 t pulley head (without pulley set on S> head) System: S 2826.20
with hydraulic erection device for WA > brackets W 2421.10
W 2421.8
Page 2 of 2
Derrick boom D = 31.5 m; R = 13.0 m
Procedure: a) Erection, take down with W> boom: Angle to S> boom 12∞> 90∞
b) Erection, take down with W> boom : Angle to S> boom 90∞ required
(W> boom hangs down)
Note: Systems with pulley set on S> head need additional ballasting per chart 12800098
217
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA > bracket II
Derrick ballast R = 18 m TAB: 12800096
600 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Derrick boom D = 31,5 m; R = 13,0 m
218
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA > bracket II
Derrick ballast R = 18 m TAB: 12800096
600 t pulley head (without pulley set on S> head) System: S 2826.20
with hydraulic erection device for WA > brackets W 2421.10
W 2421.8
Page 2 of 2
Derrick boom D = 31,5 m; R = 13,0 m
Procedure: a) Erection, take down with W> boom: Angle to S> boom 12∞> 90∞
b) Erection, take down with W> boom : Angle to S> boom 90∞ required
(W> boom hangs down)
Note: Systems with pulley set on S> head need additional ballasting per chart 12800098
219
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA >bracket II
Derrick ballast R = 20 m TAB: 12800097
600 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Derrick boom D = 31, 5 m; R = 13, 0 m
Slewing platform
Equipment configuration Central ballast
ballast
[t]
[t]
A: on crawlers 9, 1¥8, 8 m 220 95
B: on crawlers 9, 1¥8, 8 m
220 20
with installed supports
C: on supports 12, 6¥12, 6 m 220 >>
D: on supports 13, 0¥13, 0 m
(or 13, 5¥12, 9 m) 220 20
with installed crawler carriers
Boom Derrick
Permissible Procedure
ballast
weight of hook
block [t]
[m] [t]
S 35 / W 14 16, 0 >> a)
W 14 11, 0 >> a)
W 14 7, 0 >> a)
S 42 / W 14 16, 0 20 a)
W 14 11, 0 10 a)
W 14 7, 0 >> a)
S 49 / W>14 16, 0 50 a)
W 14 11, 0 40 a)
W 14 7, 0 30 a)
S 56 / W 14 16, 0 90 a)
W 14 11, 0 70 a)
W 14 7, 0 60 a)
S 63 / W 14 16, 0 120 a)
W 14 11, 0 110 a)
W 14 7, 0 90 a)
S 70 / W 14 16, 0 160 a)
W 14 11, 0 140 a)
W 14 7, 0 130 a)
Procedure: a) Erection, take down with W> boom: Angle to S> boom 12∞> 90∞
b) Erection, take down with W> boom : Angle to S> boom 90∞ required
(W> boom hangs down)
Note: Systems with pulley set on S> head need additional ballasting per chart 12800098
220
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, with hydr. erection device for WA >bracket II
Derrick ballast R = 20 m TAB: 12800097
600 t pulley head (without pulley set on S> head) System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Derrick boom D = 31, 5 m; R = 13, 0 m
221
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, 360∞, without auxiliary support TAB: 12800098
S> boom with pulley set in S> head System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 1
Derrick boom D = 31,5 m; R = 13,0 m
Additions for ballasting
Ballasting in charts TAB 12800057
TAB 12800058
TAB 12800059
TAB 12800060
TAB 12800094
TAB 12800095
TAB 12800096
TAB 12800097
apply for boom equipment configurations without pulley set on S> head.
Note: If the boom is to be erected with the pulley set on the S>head, then the suspended ballast
weight must be increased by at least the minimum values in this chart. Boom variations,
where the sum exceeds the value of 400t may not be erected.
Boom
Additional ballasting [t]
[m]
S 35 7,4 6,4 5,3 4,8
S 42 8,8 7,6 6,3 5,7
S 49 10,2 8,8 7,3 6,6
S 56 11,6 10,0 8,3 7,5
S 63 13,0 11,2 9,4 8,4
S 70 14,4 12,4 10,4 9,3
S 77 15,8 13,7 11,4 10,2
S 84 17,2 14,9 12,4 11,2
S 91 18,6 16,1 13,4 12,1
222
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800099
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Note: Erect operating modes SW_77∞ und SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
223
ERECTION AND TAKE DOWN CHARTS
SW > Operation , (S> head > pulley set 600 t; on crawler tracks) TAB: 12800099
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Erection, take down, via supported sprocket, not via the sliding section
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 23,3 19,3 15,7 12,4 9,2 6,2 3,3
S 42 25,0 25,0 25,0 22,6 19,4 15,7 12,7 9,8 7,2 4,5 2,1
S 49 19,1 16,9 15,0 12,6 10,4 7,7 5,5 3,4 1,4
S 56 7,9 6,2 5,0 3,3 1,9
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ und SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
224
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800100
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
225
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 tt; on crawler tracks) TAB: 12800100
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Erection, take down , via supported sprocket, not via sliding section
Support points 8,0 m in front of center of RDV
Boom Permissible weight of hook block on W> Boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 24,0 19,6 15,9 12,5 9,4 6,4 3,6
S 42 25,0 24,3 21,6 18,4 15,5 12,1 9,3 6,7 4,3 1,8
S 49 14,3 12,4 10,8 8,7 6,8 4,3 2,3
S 56 3,5 2,1 1,1
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
226
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800101
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 22,2 19,3 16,6 13,4 10,5 7,1 4,3 1,8
S 42 9,7 8,0 6,6 4,6 2,6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
227
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800101
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
228
ERECTION AND TAKE DOWN CHARTS
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 17,8 15,3 13,0 10,1 7,5 4,4 1,8
S 42 5,7 4,4 3,2 1,5
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
229
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Support points 8,0 m in front of center of RDV
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 24,7 21,6 18,7 15,4 12,3 8,8 6,0 3,3
S 42 12,0 10,2 8,6 6,5 4,4 1,9
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
230
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800103
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
231
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800103
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 2 of 2
Erection, take down, via supported sprocket, not via sliding section
Support points 8,0 m in front of center of RDV
Boom Permissible weight of hook block on W>boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 12,8 10,8 8,9 6,5 4,1 1, 3
S 42 1,3
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying (test
point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
232
ERECTION AND TAKE DOWN CHARTS
SW > Operation, (S> head pulley set 600 t; on crawler tracks) TAB: 12800104
SW 87∞ System: S 2826.20
W 2421.10
W 2421.8
Page 1 of 1
W 28 W 35 W 42 W 49 W 56 W 63 W 70
S 35 15,4 13,3 11,3 8,8 6,4 3,5 1,2
S 42 4,0 2,9 2,0
is not possible
Erection, take down , via supported sprocket, not via sliding section
is not possible
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
233
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
Support points 6,5 m in front of center or RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,1 19,3 15,7 12,3 9,1
S 42 25,0 25,0 25,0 25,0 25,0 23,9 20,3 17,0 13,9 10,9 8,1 5,3
S 49 25,0 25,0 24,5 21,5 18,8 15,6 12,9 10,3 8, 0 5,5 3,2
S 56 17,7 15,6 13,9 11,8 9,9 7, 4 5,5 3, 6 1,8
S 63 6,6 5,0 3,8 2,2
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,8 19,9 16,3 12,9 9,7 6,6
S 42 25,0 25,0 25,0 25,0 24,4 20,4 17,0 13,9 11,0 8,2 5,5 2,8
S 49 25,0 22,7 20,4 17,7 15,2 12,2 9,7 7, 4 5,2 2,9
S 56 13,5 11,6 10,1 8,2 6,4 4, 2 2,4
S 63 2,8 1,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
234
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
Support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 10
S 35 25.0 25.0 25.0 25.0 25.0 25.0 25.0 25.0 21.7 17.8 14.1 10.6
S 42 25.0 25.0 25.0 25.0 25.0 25.0 23.0 19.3 15.9 12.6 9.5 6.5
S 49 25.0 25.0 25.0 24.9 21.7 18.0 15.0 12.1 9.5 6.8 4.2 1.7
S 56 18.0 19.2 17.0 14.4 12.1 9.3 7.0 4.9 2.9
S 63 9.7 7.6 6.1 4.1 2.6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart),the force in the W 1> guying
(test point 2) must be limited as follows:
235
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
Support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 23,2 19,2 15,7 12,4 9,2 6,2 3,4
S 42 25,0 25,0 25,0 22,4 19,2 15,6 12,6 9,8 7,2 4,6 2,1
S 49 18,9 16,7 14,8 12,5 10,4 7,7 5,5 3, 4 1,5
S 56 7,7 6,1 5,0 3,3 1,9
Erection, take down to the front or to the rear on supports (16,0 m x 10,6 m) without crawler carrier,
Support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 24,8 20,9 16,7 13,2 10,1 7, 1 4,3 1,6
S 42 23,2 20,5 18,1 15,3 12,6 9,4 6,8 4, 4 2,1
S 49 10,7 9,0 7,6 5,7 4,0 1, 7
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
236
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
Support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,7 20,8 17,1 13,7 10,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 22,0 18,6 15,5 12,4 9,5 6,5
S 49 25,0 25,0 25,0 23,5 20,7 17,4 14,6 12,0 9,5 6,8 4, 2 1,7
S 56 18,0 17,7 15,9 13,7 11,7 9,2 7,0 4,9 2, 9
S 63 8,7 7, 0 5,8 4,1 2,6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position. .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
237
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
Support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,4 19,6 16,0 12,6 9,5 6,4
S 42 25,0 25,0 25,0 25,0 23,9 20,0 16,7 13,6 10,8 7,9 5,3 2,6
S 49 24,7 22,1 19,9 17,3 14,8 11,8 9,4 7, 1 4,9 2,6
S 56 13,0 11,1 9,7 7,8 6,1 3, 9 2,1
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 24,2 20,2 16,5 13,2 10,0 7,0 4,0
S 42 25,0 25,0 25,0 23,6 20,3 16,6 13,5 10,7 8, 0 5,3 2,8
S 49 20,2 18,0 16,0 13,6 11,4 8,6 6,4 4, 2 2,2
S 56 9,0 7,3 6,0 4,3 2,8
HNote: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
238
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
Support points 8,0 m in front of center of RDV (equipment configuration G)
Aus>
Permissible weight of hook block on W> boom head
leger
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,7 19,7 15,8 12,3 8, 9
S 42 25,0 25,0 25,0 25,0 25,0 24,6 20,7 17,2 13,9 10,7 7,7 4,8
S 49 25,0 25,0 25,0 22,2 19,2 15,7 12,8 10,0 7,5 5,0 2, 5
S 56 18,0 16,3 14,3 11,9 9,8 7,1 4,9 2,9 1, 0
S 63 7,0 5, 0 3,6 1,8
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart),the force in the W 1> guying
(test point 2) must be limited as follows:
239
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
Support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 23,5 19,1 15,5 12,2 9, 1 6,2 3,4
S 42 25,0 23,6 21,0 17,9 15,1 11,8 9,0 6, 5 4,1 1,7
S 49 13,7 11,9 10,3 8,3 6,4 4, 0 2,1
S 56 3,1 1,7
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without crawler carrier,
Support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 24,2 20,4 16,8 13,0 9,8 6, 9 4,2 1,5
S 42 17,9 15,7 13,6 11,1 8,7 5, 9 3,5 1, 3
S 49 5,9 4,5 3,4 1,8
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
240
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
support points 8,0 m in front of center of RDV (equipment configureation E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 24,7 20,8 17,2 13,7 10,6 7, 5
S 42 25,0 25,0 25,0 25,0 25,0 21,3 18,0 14,9 12,0 9,1 6, 4 3,7
S 49 25,0 23,7 21,4 18,7 16,2 13,2 10,8 8,4 6, 2 3,9 1, 7
S 56 14,6 12,7 11,2 9,3 7,6 5,3 3,5 1,8
S 63 3,9 2, 4 1,4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
241
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
Support points 6,5 m in front of center of RDV (Equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 23,9 19,5 15,9 12,5 9, 5 6,5 3,7 1,0
S 42 25,0 24,0 21,4 18,3 15,5 12,2 9,4 6, 8 4,4 2,0
S 49 14,2 12,3 10,8 8,7 6,8 4, 4 2,5
S 56 3,5 2,2 1,2
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m)with installed crawler
carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 24,3 20,4 16,3 12,9 9,8 6,9 4,1 1,4
S 42 22,5 19,9 17,6 14,8 12,2 9,1 6,5 4, 1 1,9
S 49 10,2 8,5 7,2 5,4 3,7 1, 4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
242
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,3 19,2 15,5 12,0 8,7 5,5
S 42 25,0 25,0 25,0 25,0 23,9 19,6 16,1 12,9 9,9 7,0 4, 2 1,5
S 49 25,0 22,3 19,8 16,8 14,2 11,0 8,4 5,9 3, 7 1,3
S 56 12,8 10,7 9,0 6,9 5,0 2,6
S 63 1,5
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
243
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) without crawler carrier,
Support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 24,5 21,4 17,9 14,6 11,0 8,0 5, 3 2,7
S 42 14,9 13,0 11,2 8,9 6,7 4, 1 1,9
S 49 3,4 2,2 1,3
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 19,5 16,9 14,4 11,5 8,7 5, 6 2,9
S 42 7,3 5,9 4,6 2,8 1,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
244
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
Support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 24,2 19,9 16,3 13,0 9,9 7,0 4, 2 1,5
S 42 25,0 24,4 21,8 18,8 15,9 12,7 9,9 7,3 4, 9 2,5
S 49 14,6 12,8 11,3 9,3 7,4 5,0 3,1 1,2
S 56 4,0 2, 7 1,8
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
245
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,3 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 24,9 21,7 18,2 14,9 11,3 8,3 5, 5 2,9
S 42 15,3 13,3 11,5 9,2 7,0 4, 3 2,1
S 49 3,7 2,5 1,6
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 23,8 20,8 18,1 14,9 11,8 8,4 5,6 3, 0
S 42 11,3 9,6 8,1 6,0 4,0 1, 6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
246
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 24,2 19,9 16,3 13,0 9,9 7,0 4, 2 1,5
S 42 25,0 24,4 21,8 18,8 15,9 12,7 9,9 7,4 4, 9 2,5
S 49 14,6 12,8 11,3 9,3 7,4 5,0 3,1 1,2
S 56 4,1 2, 7 1,8
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
247
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 15,0 12,9 10,8 8,3 5,8 3, 0
S 42 3,4 2,4 1,4
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49
S 35 7,7 6,2 4,7 2,6
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 23,8 20,8 17,5 14,3 10,8 7,9 5, 2 2,6
S 42 14,3 12,4 10,8 8,6 6,5 4, 0 1,8
S 49 3,0 1,9 1,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
248
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 15,2 13,0 11,0 8,5 6,0 3,1
S 42 3,6 2, 5 1,6
Erection, take down to the front or the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 11,3 9,5 7,7 5,4 3,2
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 25,0 23,8 20,8 17,5 14,3 10,8 7,9 5,2 2, 7
S 42 14,3 12,5 10,8 8,6 6,6 4,0 1,9
S 49 3,0 1, 9 1,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
249
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35
S 35 2,2 1,2
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
is not possible
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 12 4 10 6 89 66 44 17
S 42 1,3
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
250
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,6 17,8 14,3
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,5 20,0 16,6 13,5 10,3
S 49 25,0 25,0 25,0 25,0 25,0 22,7 19,6 16,6 13,9 11,1 8,5 5,8
S 56 18,0 24,3 22,1 19,4 17,1 14,2 11,8 9,6 7, 5 5,3 3, 2 1,0
S 63 10,0 12,9 11,3 9,4 7,7
Erection, take down to the front or to the rear on supports (16,0 m ¥ 12,0 m) with installed crawler
carriers (support points 6,0 m in front of center of RDV) equipment configuration H
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,6 18,8 15,2 11,8
S 42 25,0 25,0 25,0 25,0 25,0 25,0 24,0 20,5 17,1 13,9 10,9 7, 9
S 49 25,0 25,0 25,0 25,0 22,9 19,3 16,4 13,6 11,1 8,4 5, 9 3,4
S 56 18,0 20,2 18,2 15,8 13,7 11,0 8,8 6,7 4, 8 2,7
S 63 10,0 9,2 7,8 6,0 4,5
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
251
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(support points 8,0 m in front of center of RDV) equipment configuration G
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,3 20,2 16,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,7 18,9 15,5 12,1
S 49 25,0 25,0 25,0 25,0 25,0 25,0 22,4 19,1 16,0 12,9 10,1 7,2
S 56 18,0 25,0 25,0 22,9 20,1 16,8 14,1 11,5 9, 2 6,7 4,4 2,0
S 63 10,0 15,0 14,5 12,1 10,1
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
252
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without crawler carrier
(support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 22,4 18,7 15,1 11,8 8, 6
S 42 25,0 25,0 25,0 25,0 23,2 19,6 16,3 13,3 10,3 7,5 4,7
S 49 25,0 23,6 20,7 18,0 14,8 12,2 9,7 7, 4 5,0 2, 7
S 56 16,9 14,8 13,1 11,0 9,1 6,7 4,8 2,9 1, 2
S 63 5,8 4, 2 3,0 1,5
Erection, take down to the front or rear (16,0 m ¥ 10,5 m) without crawler carrier
(support points 5,25 m in front of center of RDV) equipment configuration F
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 24,6 20,5 16,8 13,4 10,2 7,1 4,2
S 42 24,1 20,7 16,9 13,8 10,9 8,2 5,5 2, 9
S 49 13,9 11,7 8,8 6,6 4,4 2, 4
S 56 4,6 3,1 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
253
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) without crawler carrier
(support points 8,0 m in front of center of RDV) equipment configuration E
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,0 19,3 15,7
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,6 18,1 14,9 11,8
S 49 25,0 25,0 25,0 25,0 25,0 24,5 21,3 18,3 15,5 12,7 10,0 7,2
S 56 18,0 25,0 24,1 21,4 18,9 16,0 13,6 11,3 9, 1 6,7 4,4 2,0
S 63 10,0 14,9 13,3 11,3 9,6
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
254
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without crawler carrier
support points 6,3 m in front of center of RDV)
Operatign
Boom Permissible weight of hook block on W > boom head
mode
[m] [t]
SW W 28
77∞ S 35 25,0
67∞ S 42 25,0
S 49 25,0
Erection, take down to the front or rear on supports (16,0 m ¥ 10,5 m) without crawler carrier
(support points 5,25 m in front of center of RDV)
Operating
Boom Permissible weight of hook block on W > boom head
mode
[m] [t]
SW W 28 W 35 W 42 W 49
S 35 25,0 25,0 25,0 25,0
77∞ S 42 25,0 25,0 25,0
67∞ S 49 20,8 18,4 16,4
S 56 9,4 7,6 6,3
Note: The boom and support combinations listed on this page have no load chart in the Sw 87 ∞
range.
Erection:
a.) Erect the S> boom in the correspoinding working angle (77∞ or 67∞), the W> boom
hangs down as far as possible.
b.) Erect the W> boom into the corresponding working position.
255
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0 17,1 13,6 10,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 21,9 18,3 15,0 11,8 8,8 5,8
S 49 25,0 25,0 25,0 22,8 19,8 16,4 13,5 10,8 8, 3 5,8 3,3
S 56 18,0 16,2 14,3 12,0 10,0 7,4 5,4 3, 4 1,6
S 63 6,3 4,5 3,2 1,6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
256
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 22,5 18,6 15,1 11,9 8,8 5, 9 3,0
S 42 25,0 25,0 24,3 21,1 18,0 14,6 11,7 9,0 6, 5 3,9 1, 5
S 49 16,3 14,4 12,8 10,7 8,8 6,3 4,3 2,3
S 56 4,9 3, 5 2,6 1,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
257
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,9 19,0 15,2 11,8 8,4
S 42 25,0 25,0 25,0 25,0 25,0 23,2 19,6 16,1 13,0 9,9 7,0 4,1
S 49 25,0 25,0 23,1 20,1 17,3 14,0 11,3 8,8 6,4 3,9 1,6
S 56 15,5 13,3 11,7 9,5 7,6 5, 2 3,3 1, 4
S 63 3,6 1,9
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
258
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 23,0 18,8 15,2 11,9 8,9 6,0 3, 2
S 42 24,7 22,1 19,7 16,9 14,2 11,0 8,4 5,9 3, 6 1,2
S 49 11,5 9,9 8,6 6,8 5,1 2,9 1,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
259
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 10
S 35 25,0 25,0 25,0 25,0 25,0 25,0 22,4 18,4 14,8 11,4 8,1 5,0
S 42 25,0 25,0 25,0 25,0 22,3 18,3 15,0 11,9 9, 0 6,2 3,5
S 49 22,0 19,5 17,3 14,7 12,3 9,3 6,9 4, 6 2,5
S 56 9,5 7,7 6,3 4,5 2,9
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
260
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 24,5 21,5 18,1 14,8 11,3 8,3 5,5 2, 9
S 42 14,1 12,3 10,7 8,5 6,5 3,9 1,8
S 49 2,0 1, 0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
261
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 10
S 35 25,0 25,0 25,0 25,0 25,0 23,5 19,7 16,2 12,9 9,8 6,9 4,1
S 42 25,0 25,0 25,0 22,2 19,2 15,8 12,9 10,2 7, 6 5,1 2,7
S 49 17,5 15,6 14,1 12,0 10,1 7,6 5,6 3, 6 1,7
S 56 6,2 4,9 3,9 2,6 1,4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
262
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Boom Permissible weight of hook block on W > boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77
S 35 22,5 19,8 17,2 14,2 11,3 8,0 5,3 2,7
S 42 9,5 8, 0 6,8 4,9 3,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
263
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (Support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91
S 35 25,0 25,0 25,0 21,5 18,1 14,4 11,2 8,4 5,7 3,0
S 42 18,0 16,1 14,3 12,0 9,8 7, 1 4,8 2, 6
S 49 5,8 4,7 3,9 2,5 1,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
264
ERECTION AND TAKE DOWN CHARTS
Erection, take down via supported sprocket, not via sliding section
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56
S 35 10,6 9,0 7,4 5,3 3,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
265
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side with auxiliary support (support points 8,0 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 13,4 11,7 10,0 7,8 5,5 2,8
S 42 1,6
is not possible
Erection, take down via supported sprocket, not via sliding section
is not possible
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
266
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,5 18,8 15,3 12,0 8, 8
S 42 25,0 25,0 25,0 25,0 25,0 22,8 19,4 16,2 13,3 10,3 7,6 4,8
S 49 25,0 24,6 22,4 19,7 17,2 14,2 11,7 9,3 7, 1 4,7 2, 5
S 56 14,8 13,0 11,6 9,7 8,0 5,8 4,0 2,3
S 63 3,6 2, 2 1,3
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 23,2 19,4 15,9 12,5 9,4 6,3
S 42 25,0 25,0 25,0 25,0 23,1 19,3 16,1 13,1 10,4 7,6 5, 0 2,4
S 49 22,5 20,3 18,3 15,9 13,6 10,8 8,5 6,3 4, 2 2,1
S 56 10,6 8,9 7,7 6,0 4,6 2,5 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
267
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
Support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,0 17,1 13,6 10,1
S 42 25,0 25,0 25,0 25,0 25,0 25,0 21,9 18,3 15,0 11,8 8,8 5,8
S 49 25,0 25,0 25,0 22,8 19,8 16,4 13,5 10,8 8, 3 5,8 3,3
S 56 18,0 16,2 14,3 12,0 10,0 7,4 5,4 3, 4 1,6
S 63 6,3 4,5 3,2 1,6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
268
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier, support points 6,3 m in
front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 22,4 18,6 15,1 11,9 8,8 5, 9 3,1
S 42 25,0 25,0 24,1 20,9 18,0 14,6 11,7 9,0 6, 5 4,0 1, 6
S 49 16,1 14,3 12,7 10,7 8,8 6,3 4,3 2,4
S 56 4,8 3, 5 2,6 1,2
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 23,6 19,9 15,9 12,6 9,5 6, 6 3,9 1, 2
S 42 20,7 18,4 16,3 13,7 11,3 8,3 5,9 3,6 1, 4
S 49 7,9 6, 5 5,4 3,8 2,4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
269
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
Support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,2 20,4 16,8 13,5 10,1
S 42 25,0 25,0 25,0 25,0 25,0 24,7 21,2 17,9 14,9 11,8 8,8 5,8
S 49 25,0 25,0 24,5 21,8 19,2 16,1 13,5 10,8 8, 3 5,8 3,3
S 56 17,0 15,1 13,6 11,7 10,0 7,4 5,4 3, 4 1,6
S 63 5,7 4,3 3,2 1,6
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
270
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
Support points 6,3 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 22,8 19,0 15,5 12,2 9,1 6,1
S 42 25,0 25,0 25,0 25,0 22,7 18,9 15,8 12,8 10,1 7,3 4, 8 2,2
S 49 21,9 19,7 17,8 15,5 13,2 10,5 8,2 6,1 4, 0 1,9
S 56 10,1 8,5 7,3 5,7 4,3 2,3
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 23,5 19,5 16,0 12,7 9,6 6, 6 3,7
S 42 25,0 25,0 25,0 22,1 19,0 15,6 12,6 9,9 7, 3 4,7 2, 3
S 49 17,5 15,5 13,9 11,8 9,8 7,2 5,2 3,2 1, 3
S 56 6,0 4, 6 3,6 2,2 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
271
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
Support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,9 19,0 15,2 11,8 8,4
S 42 25,0 25,0 25,0 25,0 25,0 23,2 19,6 16,1 13,0 9,9 7,0 4,1
S 49 25,0 25,0 23,1 20,1 17,3 14,0 11,3 8,8 6,4 3,9 1,6
S 56 15,5 13,3 11,7 9,5 7,6 5, 2 3,3 1, 4
S 63 3,6 1,9
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position. .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
272
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
Support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 22,5 18,4 14,8 11,6 8,7 5,8 3, 1
S 42 24,0 21,5 19,2 16,4 13,8 10,7 8,1 5,7 3, 4 1,1
S 49 11,0 9,4 8,2 6,5 4,9 2,7
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 22,7 19,2 15,9 12,2 9,1 6,3 3, 7 1,1
S 42 15,4 13,5 11,8 9,6 7,4 4,8 2,6
S 49 3,1 2, 1 1,3
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position ,
273
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 24,1 20,3 16,8 13,4 10,3 7,2
S 42 25,0 25,0 25,0 25,0 24,1 20,4 17,2 14,2 11,4 8,6 6,0 3,3
S 49 23,6 21,4 19,4 17,0 14,8 12,0 9,7 7, 4 5,4 3,2 1,1
S 56 11,7 10,1 8,9 7,3 5,8 3, 8 2,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
274
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 22,9 18,8 15,2 12,0 9,0 6,1 3, 4
S 42 24,5 22,0 19,7 16,9 14,2 11,1 8,5 6,1 3, 7 1,4
S 49 11,5 9,9 8,7 6,9 5,3 3,0 1,3
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed crawler
carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 23,1 19,5 15,6 12,2 9,2 6, 4 3,7 1, 1
S 42 20,0 17,8 15,8 13,3 10,9 8,0 5,6 3,3 1, 2
S 49 7,4 6, 1 5,1 3,5 2,1
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
275
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (equipment configuration G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98
S 35 25,0 25,0 25,0 25,0 25,0 25,0 22,4 18,4 14,8 11,4 8,1 5,0
S 42 25,0 25,0 25,0 25,0 22,3 18,3 15,0 11,9 9, 0 6,2 3,5
S 49 22,0 19,5 17,3 14,7 12,3 9,3 6,9 4, 6 2,5
S 56 9,5 7,7 6,3 4,5 2,9
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
276
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
support points 6,3 m in front of center of RDV (equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 22,8 20,0 16,8 13,7 10,3 7,4 4,7 2, 2
S 42 12,5 10,9 9,4 7,4 5,5 3,0 1,0
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 17,3 15,1 13,0 10,3 7,7 4,7 2,2
S 42 4,8 3, 7 2,8 1,3
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
277
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
Support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 23,4 19,2 15,7 12,5 9, 5 6,6 3,9 1,2
S 42 24,9 22,4 20,2 17,4 14,8 11,7 9,1 6, 6 4,3 2,0
S 49 12,0 10,5 9,3 7,5 5,9 3, 7 1,9
S 56 1,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows.
278
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 23,2 20,4 17,1 14,0 10,5 7,6 5,0 2, 5
S 42 12,8 11,2 9,8 7,7 5,8 3,3 1,2
S 49 1,0
Erection, take down to the front or to the rear on supports (16,0 m x 12,0 m) with installed
crawler carriers, support points 6,0 m in front of center of RDV (equipment configuration H)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77
S 35 21,7 19,1 16,6 13,7 10,9 7,6 4,9 2,5
S 42 8,8 7, 5 6,3 4,5 2,8
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
279
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m x 12,0 m) with installed crawler carriers,
support points 8,0 m in front of center of RDV (RÂstzustand G)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 23,4 19,3 15,7 12,5 9, 5 6,6 3,9 1,2
S 42 24,9 22,5 20,2 17,4 14,8 11,7 9,1 6, 7 4,3 2,0
S 49 12,0 10,5 9,3 7,6 5,9 3, 7 2,0
S 56 1,2
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
280
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
support points 6,3 m in front of center of RDV ( equipment configuration C)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 12,9 11,2 9,5 7,2 4,9 2,2
S 42 1,0
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, support points 5,25 m in front of center of RDV (equipment configuration F)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49
S 35 5,5 4, 4 3,2 1,4
Erection, take down to the side on supports (16,0 m x 10,5 m) without crawler carrier,
support points 8,0 m in front of center of RDV (equipment configuration E)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 22,2 19,5 16,4 13,4 10,1 7,3 4,7 2, 2
S 42 11,9 10,5 9,1 7,2 5,4 3,0 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows :
281
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63
S 35 13,1 11,3 9,6 7,3 5,1 2,3
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56
S 35 9,1 7,7 6,3 4,3 2,3
Erection, take down 360∞ on supports (13,0 m x 13,0 m) with installed crawler carriers,
support points 6,5 m in front of center of RDV (equipment configuration D)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84
S 35 25,0 22,2 19,6 16,5 13,5 10,1 7,3 4,7 2,3
S 42 12,0 10,5 9,2 7,3 5,4 3,0 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
282
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m x 12,6 m) without crawler carrier,
support points 6,3 m in front of center of RDV (equipment configuration C)
is not possible
Erection, take down to the front or to the rear on supports (16,0 m x 10,5 m) without
crawler carrier, Support points 5,25 m in front of center of RDV (equipment configuration F)
is not possible
W 28 W 35 W 42 W 49 W 56 W 63
S 35 10,5 9,0 7,6 5,6 3,5 1,0
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position .
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
283
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (13,0 m ¥ 13,0 m) with installed crawler carriers
(support points 6,5 m in front of center of RDV) equipment configuration D
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,2 17,5 14,0
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,7 19,4 16,0 12,9 9,9
S 49 25,0 25,0 25,0 25,0 24,9 21,3 18,4 15,6 13,0 10,3 7,8 5,2
S 56 18,0 21,6 19,7 17,4 15,2 12,6 10,4 8,3 6,4 4,3 2,3
S 63 10,0 10,1 8,8 7,1 5,7
Erection, take down to the front or to the rear on supports (16,0 m ¥ 12,0 m) with installed crawler
carriers, (support points 6,0 m in front of center of RDV) equipment configuration H
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,2 18,4 14,9 11,5
S 42 25,0 25,0 25,0 25,0 25,0 25,0 23,1 19,7 16,5 13,3 10,4 7,5
S 49 25,0 25,0 25,0 24,1 21,3 18,0 15,2 12,6 10,1 7,6 5,2 2,8
S 56 18,0 17,6 15,9 13,7 11,8 9,3 7,3 5,4 3,6 1,7
S 63 8,0 6,3 5,2 3,7 2,4
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
284
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 12,0 m) with installed crawler carriers
(support points 8,0 m in front of center of RDV) equipment configuration G
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 23,7 19,7 15,9
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 21,8 18,1 14,8 11,4
S 49 25,0 25,0 25,0 25,0 25,0 24,3 20,9 17,8 14,9 11,9 9,1 6,3
S 56 18,0 25,0 23,4 20,5 18,0 14,9 12,4 10,0 7,9 5,5 3,3 1,0
S 63 10,0 13,3 11,6 9,5 7,8
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
285
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without crawler carrier
(support points 6,3 m in front of center of RDV) equipment configuration C
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 21,9 18,2 14,7 11,4 8,3
S 42 25,0 25,0 25,0 25,0 22,1 18,7 15,6 12,6 9,7 7,0 4,3
S 49 23,7 21,5 18,9 16,4 13,5 11,0 8,7 6,5 4,2 2,0
S 56 13,9 12,1 10,7 8,9 7,3 5,1 3,4 1,7
S 63 2,8 1,4
Erection, take down to the front or to the rear on supports (16,0 m ¥ 10,5 m) without crawler carrier
(eupport points 5,25 m in front of center of RDV) equipment configuration F
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 23,8 19,8 16,2 12,9 9,7 6,8 3,9
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
286
ERECTION AND TAKE DOWN CHARTS
Erection, take down to the side on supports (16,0 m ¥ 10,5 m) without crawler carrier
(support points 8,0 m in front of center of RDV) equipment configuration E
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49 W 56 W 63 W 70 W 77 W 84 W 91 W 98 W 105
S 35 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 25,0 22,7 19,0 15,4
S 42 25,0 25,0 25,0 25,0 25,0 25,0 25,0 24,5 21,0 17,6 14,5 11,4
S 49 25,0 25,0 25,0 25,0 25,0 23,2 20,2 17,3 14,6 11,9 9,1 6,3
S 56 18,0 23,8 21,8 19,4 17,2 14,5 12,2 10,0 7,9 5,5 3,3 1,0
S 63 10,0 12,2 10,9 9,1 7,7
Note: During the movement on the ground (W> jib in rolling cart), the force in the W 1> guying
(test point 2) must be limited as follows:
Note: Erect operating modes SW_77∞ and SW_67∞ first as SW_87∞ and then luff to the
corresponding position.
287
ERECTION AND TAKE DOWN CHARTS
Erection, take down 360∞ on supports (12,6 m ¥ 12,6 m) without crawler carrier
(support points 6,3 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28
S 35 25,0
S 42 25,0
S 49 25,0
Erection, take down to the front or to the rear on supports (16,0 m ¥ 10,5 m) without crawler carrier,
(support points 6,3 m in front of center of RDV)
Boom Permissible weight of hook block on W> boom head
[m] [t]
W 28 W 35 W 42 W 49
S 35 25,0 25,0 25,0 25,0
S 42 25,0 25,0 25,0
S 49 18,0 16,0 14,3
S 56 6,4 4,9 3,9
Note: The boom and support combinations listed on this page have no load charts in the Sw 87∞
range.
Erection:
a.) Erect S> boom in corresponding working angle (77∞ or 67∞), the W> boom hangs down as
far as possible.
b.) Erect W> boom into the corresponding working position.
288
ERETION AND TAKE DOWN CHARTS
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
289
ERETION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
290
ERETION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
291
ERETION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
292
ERETION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
293
ERETION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
294
ERETION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
pinned pinned
[t/t] [t] [t] [m] [t]
300 320 S 63 / W 70 16,0
220/95 (A) 240 250 W 70 7,5
220/20 (B,D) 210 220 W 70 3,5
220/>> (C) 320 340 S 63 / W 77 16,0
260 270 W 77 7,5
220 230 W 77 3,5
340 360 S 63 / W 84 16,0
270 280 W 84 7,5
230 250 W 84 3,5
290 300 S 63 / W 91 7,5
250 260 W 91 3,5
310 320 S 63 / W 98 7,5
270 280 W 98 3,5
330 340 S 63 / W 105 7,5
290 300 W 105 3,5
260 280 S 70 / W 28 16,0
210 230 W 28 7,5
190 210 W 28 3,5
270 290 S 70 / W 35 16,0
220 240 W 35 7,5
200 220 W 35 3,5
280 300 S 70 / W 42 16,0
230 250 W 42 7,5
210 230 W 42 3,5
310 330 S 70 / W 49 16,0
260 280 W 49 7,5
230 250 W 49 3,5
295
ERETION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
pinned pinned
[t/t] [t] [t] [m] [t]
330 350 S 70 / W 56 16,0
220/95 (A) 270 290 W 56 7,5
220/20 (B,D) 240 260 W 56 3,5
220/>> (C) 350 370 S 70 / W 63 16,0
290 300 W 63 7,5
260 270 W 63 3,5
370 380 S 70 / W 70 16,0
300 320 W 70 7,5
270 280 W 70 3,5
390 400 S 70 / W 77 16,0
320 330 W 77 7,5
280 290 W 77 3,5
*** *** S 70 / W 84 16,0
330 350 W 84 7,5
290 310 W 84 3,5
350 360 S 70 / W 91 7,5
310 320 W 91 3,5
370 380 S 70 / W 98 7,5
320 340 W 98 3,5
390 400 S 70 / W 105 7,5
340 350 W 105 3,5
340 360 S 77 / W 35 16,0
280 310 W 35 7,5
260 280 W 35 3,5
350 370 S 77 / W 42 16,0
300 320 W 42 7,5
270 290 W 42 3,5
296
ERETION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
pinned pinned
[t/t] [t] [t] [m] [t]
380 400 S 77 / W 49 16,0
220/95 (A) 320 340 W 49 7,5
220/20 (B,D) 290 310 W 49 3,5
220/>> (C) 400 *** S 77 / W 56 16,0
330 350 W 56 7,5
300 320 W 56 3,5
*** *** S 77 / W 63 16,0
350 370 W 63 7,5
320 340 W 63 3,5
*** *** S 77 / W 70 16,0
370 390 W 70 7,5
330 350 W 70 3,5
*** *** S 77 / W 77 16,0
380 400 W 77 7,5
340 360 W 77 3,5
*** *** S 77 / W 84 16,0
400 *** W 84 7,5
360 370 W 84 3,5
*** *** S 77 / W 91 7,5
370 390 W 91 3,5
*** *** S 77 / W 98 7,5
390 400 W 98 3,5
*** *** S 77 / W 105 7,5
400 *** W 105 3,5
*** *** S 84 / W 42 16,0
360 380 W 42 7,5
330 360 W 42 3,5
297
ERETION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
pinned pinned
[t/t] [t] [t] [m] [t]
*** *** S 84 / W 49 16,0
220/95 (A) 380 400 W 49 7,5
220/20 (B,D) 350 370 W 49 3,5
220/>> (C) *** *** S 84 / W 56 16,0
400 *** W 56 7,5
370 390 W 56 3,5
*** *** S 84 / W 63 16,0
*** *** W 63 7,5
390 *** W 63 3,5
*** *** S 84 / W 70 16,0
*** *** W 70 7,5
400 *** W 70 3,5
*** *** S 84 / W 77 16,0
*** *** W 77 7,5
*** *** W 77 3,5
*** *** S 84 / W 84 16,0
*** *** W 84 7,5
*** *** W 84 3,5
*** *** S 84 / W 91 7,5
*** *** W 91 3,5
*** *** S 84 / W 98 7,5
*** *** W 98 3,5
*** *** S 84 / W 105 7,5
*** *** W 105 3,5
298
ERETION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800135
System: 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
pinned pinned
[t/t] [t] [t] [m] [t]
*** *** S 91 / W 49 7,5
220/95 (A) *** *** W 49 3,5
220/20 (B,D) *** *** S 91 / W 56 7,5
220/>> (C) *** *** W 56 3,5
*** *** S 91 / W 63 7,5
*** *** W 63 3,5
*** *** S 91 / W 70 7,5
*** *** W 70 3,5
*** *** S 91 / W 77 7,5
*** *** W 77 3,5
*** *** S 91 / W 84 7,5
*** *** W 84 3,5
*** *** S 91 / W 91 7,5
*** *** W 91 3,5
*** *** S 91 / W 98 7,5
*** *** W 98 3,5
*** *** S 91 / W 105 7,5
*** *** W 105 3,5
299
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 1 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
300
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 2 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
301
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 3 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
302
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 4 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
303
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 5 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
304
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
305
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
306
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
307
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
308
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 10 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
309
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800136
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 11 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
310
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 1 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
311
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 2 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
312
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 3 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
313
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 4 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
314
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 5 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
315
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
316
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
317
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
318
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
319
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 10 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
320
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800137
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
Page 11 of 11
A: on crawler tracks 9,1 m x 8,8 m
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
321
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
322
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
323
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
324
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
325
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
326
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
327
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
328
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
329
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
330
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
331
ERECTION AND TAKE DOWN CHARTS
SDWB > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800138
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
332
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
333
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
334
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
335
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
336
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
337
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
338
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
339
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
340
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
341
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
342
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 13 m, 600 t pulley set on S> head) TAB: 12800139
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
343
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
344
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
345
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
346
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
347
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
348
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
349
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
350
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
351
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
352
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
353
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation , with hydr. erection device for WA> bracket II
(Derrick ballast R = 15 m, 600 t pulley set on S> head) TAB: 12800140
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
354
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
355
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
356
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
357
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
358
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, Working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
359
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
360
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
361
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
362
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
363
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, Working range 360∞, track pad width 1,5
m
or 13,5 m x 12,9 m, crawler tracks installed, Working range 360∞, track pad width 2,0
m
DerrickBoom D = 31,5 m; R = 13 m
364
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 18 m, 600 t pulley set on S> head) TAB: 12800141
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
DerrickBoom D = 31,5 m; R = 13 m
365
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation with hydr. erection device for WA> bracket II
(derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 1 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
366
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 2 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
367
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 3 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
368
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 4 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
369
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 5 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
370
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 6 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
371
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 7 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
372
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 8 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
373
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 9 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
374
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 10 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
375
ERECTION AND TAKE DOWN CHARTS
SDWBW > Operation, with hydr. erection device for WA> bracket II
(Derrick ballast R = 20 m, 600 t pulley set on S> head) TAB: 12800142
System: S 2826.20
D 2421.10
Erection, take down 360∞ W 2421.10
without auxiliary support W 2421.8
A: on crawler tracks 9,1 m x 8,8 m Page 11 of 11
B: on crawler tracks 9,1 m x 8,8 m; supports installed
C: on supports 12,6 m x 12,6 m, working range 360∞
D: on supports 13,0 m x 13,0 m, crawler tracks installed, working range 360∞, track pad width 1,5 m
or 13,5 m x 12,9 m, crawler tracks installed, working range 360∞, track pad width 2,0 m
Derrick boom D = 31,5 m; R = 13 m
376
ERECTION AND TAKE DOWN CHARTS
Slewing
Permissible weight
platform / Boom combination
of hook block on
central ballast
boom nose
* = A hook block weighing between 2,5 t and 5,5 t, in angle range of 0∞ to 25∞ (main boom to the
horizontal) must be carried along on the ground with a suitable vehicle.
CAUTION: The boom system may only be subjected to maximum 2,0 t with a carried
along hook block.
377
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800147
System: S 2826.20
LI 2421.8
D: on supports: 13,0 m ¥ 13,0 m, crawlers installed; 360∞; track plate width 1,5 m
or: 13,5 m ¥ 12,9 m, crawlers installed; 360∞; track plate width 2,0 m
G: on supports: 16,0 m ¥ 12,0 m, crawlers installed; to the side
H: on supports: 16,0 m ¥ 12,0 m, crawlers installed; 360∞
Page 1 of 2
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
D G H
13,0 m ¥ 13,0 m 16,0 m ¥ 12,0 m 16,0 m ¥ 12,0 m
13,5 m ¥ 12,6 m
360∞ to the side 360∞
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual. .
378
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800147
System: S 2826.20
LI 2421.8
D: on supports: 13,0 m ¥ 13,0 m, crawlers installed; 360∞; track plate width 1,5 m
or: 13,5 m ¥ 12,9 m, crawlers installed; 360∞; track plate width 2,0 m
G: on supports: 16,0 m ¥ 12,0 m, crawlers installed; to the side
H: on supports: 16,0 m ¥ 12,0 m, crawlers installed; 360∞
Page 2 of 2
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
D G H
13,0 m ¥ 13,0 m 16,0 m ¥ 12 m 16,0 m ¥ 12 m
13,5 m ¥ 12,6 m
360∞ to the side 360∞
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
379
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800148
System: S 2826.20
LI 2421.8
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
C E F
12,6 m ¥ 12,6 m 16,0 m ¥ 10,5 m 16,0 m ¥ 10,5 m
360∞ to the side 360∞
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual. .
380
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800148
System: S 2826.20
LI 2421.8
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
C E F
12,6 m ¥ 12,6 m 16,0 m ¥ 10,5 m 16,0 m ¥ 10,5 m
360∞ to the side 360∞
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual. .
381
ERECTION AND TAKE DOWN CHARTS
SL > operation (SL4HS) with auxiliary jib 120t (HS 6,0 m) TAB: 12800149
System: S 2826.20
LI 2421.10
Page 1 of 2
A: on crawler tracks, 9,1m x 8,8m; working range 360∞; 95t ZB
B: on crawler tracks, 9,1m x 8,8m; supports installed; working range 360∞; 20t ZB
C: on supports, 12,6m x 12,6m; working range 360∞; 0t ZB
D: on supports, 13,0m x 13,0m;crawler installed; working range 360∞; 20t ZB
E: on supports, 16,0m x 10,5m; working range to the side; 0t ZB
F: on supports, 16,0m x 10,5m; working range 360∞; 0t ZB
Slewing Main Permissible total weight of hook blocks on main boom and
platform boom auxiliary jib for equipment configuration:
ballast
B
A A C
9,1 x 8,8 m
9,1 x 8,8 m 9,1 x 8,8 m 9,1 x 8,8 m
360∞
360∞ to the side with 360∞
supports
auxiliary
installed
support
95 t ZB 95 t ZB 0 t ZB
20 t ZB
* Can only be erected with hook block. The hook block must be carried along in the main boom angle ran>
ge of 0∞ to 30∞ to the horizontal. Max. 0.5 t of the weight of the hook block may be placed on the boom.
** For high sheave numbers we recommend to use a higher hook block weight; however, during the
erection and take down procedure is the permissible load limited to the value in above chart! For
relationship between reeving number and hook block weight, see load chart manual!
382
ERECTION AND TAKE DOWN CHARTS
SL > operation (SL4HS) with auxiliary jib 120t (HS 6,0 m) TAB: 12800149
System: S 2826.20
LI 2421.10
Page 2 of 2
A: on crawlers, 9,1m x 8,8m; working range 360∞; 95t ZB
B: on crawlers, 9,1m x 8,8m; supports installed; working range 360∞; 20t ZB
C: on supports, 12,6m x 12,6m; working range 360∞; 0t ZB
D: on supports, 13,0m x 13,0m;crawler installed; working range 360∞; 20t ZB
E: on supports, 16,0m x 10,5m; working range to the side;0t ZB
F: on supports, 16,0m x 10,5m; working range 360∞; 0t ZB
* Can only be erected with hook block. The hook block must be carried along in the main boom angle ran>
ge of 0∞ to 30∞ to the horizontal. Max. 0.5 t of the weight of the hook block may be placed on the boom.
** For high sheave numbers we recommend to use a higher hook block weight; however, during the
erection and take down procedure is the permissible load limited to the value in above chart! For
relationship between reeving number and hook block weight, see load chart manual!
383
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800154
System: S 2826.20
LI 2421.8
A: on crawlers: 9,1 m ¥ 8,8 m,
B: on crawlers: 9,1 m ¥ 8,8 m, supports installed
Page 1 of 2
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
A B
(Equipment Crawlers 9,1 m ¥ 8,8 m Crawlers 9,1 m ¥ 8,8 m
configuration) supports installed
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual. .
384
ERECTION AND TAKE DOWN CHARTS
SL > Operation (SL3HS) with auxiliary jib 100 t (HS 6,0 m) TAB: 12800154
System: S 2826.20
LI 2421.8
A: on crawlers: 9,1 m ¥ 8,8 m,
B: on crawlers: 9,1 m ¥ 8,8 m, supports installed
Page 2 of 2
Slewing Main boom Permissible weight of both hook blocks together on the main boom
platform / and auxiliary jib for equipment configuration
central ballast
A B
(Equipment Crawlers 9,1 m ¥ 8,8 m Crawlers 9,1 m ¥ 8,8 m
configuration) supports installed
* = For high strand numbers, a higher hook block weight is recommended; during the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual. .
385
ERECTION AND TAKE DOWN CHARTS
SLD > operation (SL7DHS) with auxiliary jib 120t (HS>6,0 m) TABt: 12800155
System: S 2826.20
LI 2421.10
D 2421.10
A: on crawler tracks,9,1m x 8,8m; working range360∞; 95 t ZB
B: on crawler tracks,9,1m x 8,8m; supports installed; working range360∞; 20 t ZB
D: on supports, 13,0m x 13,0m;crawler installed; working range360∞; 20 t ZB
(Equipment set
up
configuration) 13 m 15 m 18 m 20 m
386
ERECTION AND TAKE DOWN CHARTS
SLD > operation (SL7DHS) with auxiliary jib 120t (HS>6,0 m) TAB: 12800156
System: S 2826.20
LI 2421.10
D 2421.10
The force in test point I (guying between derrick and SA bracket) must be monitored via the monitor
screen.
When lifting the suspended ballast pallet, the distance to the ground must be limited to max. 10 cm.
Before ballasting the slewing platform ballast on or off on the nominal ballast of the load chart, the
boom system must be set into the correspondingly steepest operating position.
The ballast required for the removal must be available quickly and must always remain within the
reach of the crane.
387
ERECTION AND TAKE DOWN CHARTS
* Can be erected only with hook block. The hook block must be carried along in the main boom angle
range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be placed
on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
388
ERECTION AND TAKE DOWN CHARTS
* Can be erected only with one hook block. The hook block must be carried along in the main boom
angle range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be
placed on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
389
ERECTION AND TAKE DOWN CHARTS
C E F
12,6 m x 12,6 m 16,0 m x 10,5 m 16,0 m x 10,5 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
220 SL 70 14 14 14
SL 77 14 14 13
SL 84 13 14 8
SL 91 7,5 12 3,0**
SL 98 4,0** 9 >
SL 105 > 4,0** >
SL 112 > 5,0* >
170 SL 70 14 14 12
SL 77 11 14 6,5
SL 84 6,5 13 2,0**
SL 91 > 8 >
SL 98 > 4,0** >
SL 105 > > >
SL 112 > > >
* Can be erected only with one hook block. The hook block must be carried along in the main boom
angle range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be
placed on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
390
ERECTION AND TAKE DOWN CHARTS
C E F
12,6 m x 12,6 m 16,0 m x 10,5 m 16,0 m x 10,5 m
360∞ to the side 360∞
[t/t] [m] [t] [t] [t]
200 *** SL 70 14 14 14
SL 77 14 14 14
SL 84 14 14 10
SL 91 9 12 5,0
SL 98 5,5 9 1,5**
SL 105 > 4,0** >
SL 112 > 5,0* >
125 *** SL 70 13 14 8
SL 77 7,5 14 3,0**
SL 84 3,0** 9 >
SL 91 > 4,0** >
SL 98 > > >
SL 105 > > >
SL 112 > > >
* Can be erected only with one hook block. The hook block must be carried along in the main boom
angle range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be
placed on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
391
ERECTION AND TAKE DOWN CHARTS
* Can be erected only with hook block. The hook block must be carried along in the main boom angle
range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be placed
on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
392
ERECTION AND TAKE DOWN CHARTS
* Can be erected only with hook block. The hook block must be carried along in the main boom angle
range of 0∞ to 35∞ to the horizontal. From the weight of the hook block, maximum 1.0 t may be placed
on the boom.
** For high strand numbers, a higher hook block weight is recommended. During the erection / take
down procedure the permissible load is limited to the value from above chart!
For relationship between strand number and hook block weight, see load chart manual.
393
ERECTION AND TAKE DOWN CHARTS
SDWV / SDWVB(W) > Operation, 360 ∞, without auxiliary support TAB: 12800167
Boom: S> 94,5 m , without pulley set on S > head System: S 2826.30
W> 21 m with W > 600 t > pulley head and 60 t boom nose S 2826.20
Derrick 31,5 m D 2421.10
Derrick radius 13,0 m W 2421.10
[t] [t]
Note: For erection or take down, the W > boom must hang down.
Minimum angle 71∞ to the S > boom.
15 400
18 340
20 310
Note: For the relapse retention of the W> boom, the following conditions must be observed:
Minimum weight of the hook block on the W > pulley set: 11 t
Minimum reeving of the hook block 2 x 4
In the steepest position, at a boom angle above 70∞, the hook block may not be set down.
394
ERECTION AND TAKE DOWN CHARTS
* The ballast on the erection frame must be in set down condition at the start of the erection
procedure.
** The hook block must be reeved according to TAB. 12800169 in the prefix of the load chart
manual.
Until an angle of 70∞ is reached between the SL> and K>boom, the K>boom head must be carried along
while placed on a suitable vehicle.
395
AUFRICHT> UND ABLEGETABELLEN
** The hook block must be reeved according to TAB. 12800169 in the prefix of the load chart
manual.
Until an angle of 70∞ is reached between the SL> and K>boom, the K>boom head must be carried
along while placed on a suitable vehicle.
396
ERECTION AND TAKE DOWN CHARTS
397
ERECTION AND TAKE DOWN CHARTS
SL8DHS operation with auxiliary jib 120 t (HS 6.0 m) TAB: 12800179
System: S 2826.20
LI 2421.10
D 2421.10
A: on crawlers, 9.1m x 8.8m; 360∞ working range; 95 t ZB
B: on crawlers, 9.1m x 8.8m; supports installed; 360∞ working range; 20 t ZB
D: on supports,13.0m x 13.0m; crawler installed; 360∞ working range; 20 t ZB
Turntable Required
Main boom Permissible total
ballast Derrick ballast
weight of all for
hook blocks 20 m ballast radius
[m] [t] [t]
[t]
The force in test point I (guying between derrick and SA bracket) must be monitored via the display.
When lifting the suspended ballast pallet off, the distance to the ground must be limited to max. 10 cm.
Before ballasting the turntable ballast on the nominal ballast of the load chart and for un>ballasting
theturntable ballast, the boom system must be set into the steepest operating position.
The ballast required for removal must always remain within the reach of the crane for quick access.
Note: The use of the LI > intermediate section for flying assembly is not intended for length of
more than 119 m.
398
ERECTION AND TAKE DOWN CHARTS
SL8DHS operation with auxiliary jib 120t (HS 6.0 m) TAB: 12800181
System: S 2826.20
LI 2421.10
D 2421.10
A: on crawlers, 9.1m x 8.8m; 360∞ working range; 95 t ZB
B: on crawlers, 9.1m x 8.8m; supports installed; 360∞ working range; 20 t ZB
D: on supports, 13.0m x 13.0m; crawler installed; 360∞ working range; 20 t ZB
Note: The use of the LI > intermediate section for flying assembly is not intended for length of
more than 119 m.
399