Professional Documents
Culture Documents
Floorsil 2
Floorsil 2
is a high-performance one-component silicone sealant
is based on a oxime cross-linking system
vulcanizes at room temperature (RTV)
Floorsil 2 is designed for applications in the, aircraft industry. Sealing non-textile floor
coverings made of silicone, PVC in aircrafts.
Please note: Floorsil 2 is not suitable for sewage applications, for motorway and runway applications. Do not use Floorsil 2 for sealing
applications around petrol pumps.
Advantages
Especially designed for high – duty floor joints and acid proof constructions in contrast to
conventional sealants, Floorsil 2 shows a very high notched impact value and an extreme
resistance to chemicals
Fast curing and short tack – free time
Excellent compatibility and adhesion to silicone floor coverings
Excellent weatherability, resistance to ageing, UV-radiation, temperature resistance
Resistance to lift truck and fork lift traffic
Resistance to steam jet cleaning
Excellent resistance to detergents
Extreme resistance to chemicals (see chapter 2.)
Ready to use
High tensile strength and high shore – A – Hardness ensure an excellent notched impact value
Contains no solvents, formaldehyde, CFC, PCB, PCP
These data are not intended for use in preparing specifications. Please contact METZELER before writing
specifications.
Page 1 of 3
Technical Data Sheet
Floorsil 2
3. Packaging
Floorsil 2 is packed in 310 ml cartridges. A carton is packed with 12 cartridges.
You can have special cartridges on request.
4. Application sealant
Avoid direct contact between sealant and plasticizer emigrating products: Direct contact between
sealant and the following plasticizer emigrating products should be avoided because these products
may cause yellowing of light-coloured silicone sealants: e.g. butyl rubber;
ethylenepropylenedienemonomerepolymer (EPDM), neoprene, bitumious and products.
Application sealant: Sealant must be applied after the primer has dried up for least 15 minutes
Page 2 of 3
Technical Data Sheet
Floorsil 2
Avoid air entrapment: The joint must be completely filled to avoid air entrapment and to make the joint
leak-proof
Tooling / smoothing: The sealant must be smoothly tooled before the skin – formation in order to
ensure integral contact with joint flanks.
Steam jet apparatus: On using a steam – jet apparatus the distance between the joint and the steam
nozzle is ton be at least 50 cm.
Using the sealed objects the first time: Floorsil 2 must have cured completely before the sealant object
is exposed to mechanical or chemical stress the first time. Floorsil 2 should have cured at least 24 to 48
hours at room temperature (see chapter 1. For curing data)
6. Warranty
All information, data, direction or advice presented by METZELER are believed to be accurate and reliable, but do not absolve the
user from carefully checking all supplies immediately on receipt. However, as METZELER has no control over the uses to which its
products may be put or the conditions of use, it is the user’s responsibility to determine suitability of use e.g. by performing own
tests. METZELER makes no warranties concerning the fitness or suitability of its products for a particular use. Statements
concerning possible or suggested uses of the materials described herein can not be seen as warranty for your application.
METZELER warrants only that its products will meet its specifications. We reserve the right to alter product constants within the
scope of technical progress or new developments.
Of course, METZELER can perform tests and deliver a special written recommendation for a specific application on request.
If the application in which the products are used requires governmental approval or clearance, the user must obtain it.
In the event of a claim due to failure of our products, METZELER’s sole liability is limited to provide sufficient product for
replacement. METZELER will not be liable for any labour or any other costs associated with the repair, if the failure is due to
incorrect use of any materials.
The recommendations do not absolve the user from the obligation of investigating the possibility of infringement of third parties’
rights and, if necessary, clarifying the position.
7. Edition
Page 3 of 3