Professional Documents
Culture Documents
Description
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied.
100
VALUE
90
PERCENT OF PEAK
50
10
O1 T TIME
T1
T2
Figure 1 Figure 2
O 1 = Virtual Origin of Wave
T = Time From 10% to 90% of Peak
Should transients occur in rapid succession, the average 01 = Virtual OriginTof=Wave
1 Virtual Front time = 1.25 • t
power 100 dissipation result is simply the energy T = Time from 10% T 2 =toVirtual
90% of TimePeak
to Half Value (Impulse Duration)
(watt-seconds) per pulse times the number of pulses T1 = Rise TimeExample:
= 1.25 x TFor an 8/20 µs Current Waveform:
per second. The power so developed must be within T2 = Decay Time8 s = T 1 = Virtual Front Time
the specifications shown on the Device Ratings and Example - For 20 s = Tµs
an 8/20 2 =Current
Virtual Time to Half Value
Waveform:
Specifications table for the specific device. The operating 8µs = T1 = Rise Time
values must be derated as shown in above. 20µsFIGURE 2. PEAK
= T2 = Decay PULSE CURRENT
Time TEST WAVEFORM
10000
50,000
Maximum Clamping Voltage TA = -55 C to 85C 1 DISC SIZE 34mm
DHB34 Series 20,000 2 V131DHB34 - V751DHB34
110 to 750V AC Rating
Voltage -
V751 10,000 10
VOLTS
V661 V681
5,000
V571 10 2 10 5
SURGE CURRENT (A)
10 6
V551
V511
2,000
10 3
1000 1,000
10 4
500
200
V481
V111
V141 V131 100
V441
50
V151
V421
20 INDEFINITE
100
0.001 0.01 0.1 1 10 100 1000 10000 100000
10
Current - AMPS 20 100 1,000 10,000
Figure 3 V391 V351 V331 V321 V301 V271 V251 V201 V181
Figure 4 IMPULSE DURATION ( µs)
Soldering Parameters
300 300
Maximum Wave 260C
Maximum Wave 240C
250 250
TEMPERATURE (ºC)
TEMPERATURE (ºC)
200 200
150 150
100 100
50 50
0 0
0 0.5 1 1.5 2 2.5 3 3.5 4 0 0.5 1 1.5 2 2.5 3 3.5 4
Figure 5 TIME(MINUTES) Figure 6 TIME(MINUTES)
Dimensions (mm)
37.5 max
T max Table of Dimensions - Thickness and Terminal Offsets
NOTES:
- Terminals Configuration:
Terminals A & B are connected to one varistor element.
Terminals B & C connected to second varistor element.
- Dimensions:
Measures are in mm is typical, unless otherwise specified.
V 13 1 DHB 34
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are
not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics.
© 2020 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/20/20