Professional Documents
Culture Documents
200 20 Pi DTS 00007
200 20 Pi DTS 00007
D1BM APPLICABILITY
RGE Comp. Hub 6S
Comp. Hub 7S
Comp. Hub 8S
Comp. Hub 4S
RL Comp. Hub 1S
QG2 Comp. Hub 4N
Comp. Hub 6N
B 6 8 Updated the Table Header detail and format for the Codes
and Standard
B 7 10 Updated the Table Header detail and format for the Project
Document References
HOLD LIST
Contents
1 INTRODUCTION ........................................................................................................................... 5
2 DEFINITIONS AND ACRONYMS ................................................................................................. 6
2.1 Definitions ............................................................................................................................ 6
2.2 Acronyms ............................................................................................................................. 6
3 PURPOSE OF DOCUMENT ......................................................................................................... 7
3.1 General ................................................................................................................................ 7
4 BUTTERFLY VALVE INDEX ......................................................................................................... 8
5 ORDER OF PRECEDENCE ......................................................................................................... 8
6 NON-COMPLIANCE / DEVIATION: .............................................................................................. 8
7 APPLICABLE CODES & STANDARDS ........................................................................................ 8
7.1 API–American Petroleum Institute....................................................................................... 9
7.2 ASME–American Society Of Mechanical Engineers ........................................................... 9
7.3 ASTM - American Society for Testing and Material ............................................................ 9
7.4 BSI–British Standards Institution ....................................................................................... 10
7.5 MSS–Manufacturers Standardization Society ................................................................... 10
7.6 NACE - National Association of Corrosion Engineers ....................................................... 10
8 REFERENCES ............................................................................................................................ 10
APPENDIX-1 (DATASHEETS FOR BUTTERFLY VALVES) ............................................................... 11
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 3 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Figures
Figure 1-1: North Field Context ............................................................................................................... 5
Tables
Table 4-1 : Butterfly Valve Index ............................................................................................................. 8
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 4 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
1 INTRODUCTION
The reservoir pressure in Qatar’s North Field has been declining due to continuous production since
the early 1990s. The North Field is the world’s largest natural gas field and accounts for nearly all of the
state of Qatar’s gas production. The principal objective of the NFPS project is to sustain plateau from
existing QG South Operation – RL Dry Gas, RGE Wet gas and existing QG North Operation – QG1 &
QG2, production areas by implementing an integrated and optimum investment program consisting of
subsurface development, pressure drop reduction steps and compression. Refer to figure below for a
schematic of North Field.
Figure 1-1: North Field Context
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 5 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Drilling and Looping Investments #1 and #2 are in execution phase and are being executed by I1P1
EPC, EPCO and EPCL projects with the exception of WHP13N, which will be part of NFPS
Compression project execution. The NFPS Compression Project involves the installation of large
offshore compression facilities at multiple locations. The compression facilities will be installed after the
completion of the Drilling and Looping Projects.
Qatargas Operating Company Limited is leading the development of the North Field Production
Sustainability (NFPS) Project. The principal objective of the NFPS project is to economically sustain
plateau from existing QG South (RGE, RL) and QG North (QG1 & QG2) production assets by
implementing an integrated and optimum investment program consisting of subsurface developments,
pressure drop reduction steps and offshore compression facilities installation.
CONTRACTOR is awarded to perform FEED for NFPS Compression Project – RGE, RL and QG2
Facilities.
2 DEFINITIONS AND ACRONYMS
2.1 Definitions
The following definitions used in the present PROJECT procedure are:
PROJECT NFPS Compression Project FEED
COMPANY Qatargas Operating Company limited
CONTRACTOR Middle East Projects International (Technip MEPI)
EPC CONTRACTOR CONTRACTOR engaged by COMPANY to execute EPC contract activities
or/and services
SUBCONTRACTOR A party who is providing subcontracted services specified and ordered by
CONTRACTOR or EPC CONTRACTOR
THIRD PARTY Third Party appointed by CONTRACTOR
VENDOR (SUPPLIER) A party who is responsible to manufacture and supply equipment and/or
services
SUB-VENDOR A party who is responsible to manufacture and supply equipment and/or
(SUB-SUPPLIER) services under responsibility of main VENDOR
SHALL The word “Shall” is to be understood as a mandatory requirement.
SHOULD The word “Should” is to be understood as strongly recommended.
MAY The word “May” is to be understood as an action to be undertaken at
CONTRACTOR / COMPANY ‘s discretion and upon evaluation of a review of
the circumstances of the issue in question.
2.2 Acronyms
The following acronyms are used in this document.
Term Description
AED Anti Explosive Decompression
API American Petroleum Institute
ASME American Society of Mechanical Engineers
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 6 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
3.1 General
This document covers the technical requirements for the Butterfly Valves data Sheets for offshore
scope. This document shall be read in conjunction with Specification for Manual valves document
number 200-20-PI-SPC-00006 [3].
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 7 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
PIPE VALVE END
VALVE SIZE(INCH) DATASHEET
CLASS RATING CONNECTIONS
NUMBER
5 ORDER OF PRECEDENCE
In general the order of precedence shall be as follows:
a) Qatari Governmental and Regulatory Requirements
b) COMPANY Policies and Procedures
c) Project Specifications
d) Industry Codes and Standards
e) COMPANY and CONTRACTOR’S lessons learned
If CONTRACTOR / VENDOR deems any deviations from the specifications will result in significant
project cost and schedule saving, proposal to such deviations shall be submitted to COMPANY for
review and approval. CONTRACTOR / VENDOR shall not proceed with any deviation to the
Specifications without prior COMPANY APPROVAL.
6 APPLICABLE CODES & STANDARDS
The following codes, standards and specification referenced within the document shall be considered
as part of this specification. Conflict among applicable specification and / or codes shall be brought to
the attention of the COMPANY for resolution. COMPANY decision shall be final and shall be
implemented. The latest editions of codes and specification effective as on date of contract shall be
followed.
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 8 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[1] API SPEC 6FA Specification for Fire Test for Valves
[3] API STD 607 Fire Test for Soft-Seated Quarter-Turn Valves
[4] API STD 609 Butterfly Valves: Double-flanged, Lug- and Wafer-type
[1] ASME B16.5 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24
Metric/Inch Standard
[1] ASTM A 216 Standard Specification for Steel Castings, Carbon, Suitable for
Fusion Welding, for High-Temperature Service
[4] ASTM F 467 Standard Specification for Nonferrous Nuts for General Use
[5] ASTM F 468 Standard Specification for Nonferrous Bolts, Hex Cap Screws,
Socket Head Cap Screws, and Studs for General Use
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 9 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[1] MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
[1] NACE MR0175/ISO 15156 Petroleum and Natural Gas Industries Materials for Use in H 2S-
Containing Environments in Oil and Gas Production
7 REFERENCES
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 10 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 11 of 11
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 1 of 10
BUTTERFLY Range: NPS 3" to 6"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.5 CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7,8
OPERATOR Lever Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and valves to have locking facility to allow locking in the open, closed & all the intermediate
position by pad locks / Car seal arrangment without chains. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine
Offshore environment. Vendor shall provide relevant valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625
(ASTM F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the
diameter, effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design
code of the bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition.
The bolts for cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 2 of 10
BUTTERFLY Range: NPS 8" to 10"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A35B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.5 CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7, 8
OPERATOR Gear Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide
relevant valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625
(ASTM F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the
diameter, effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design
code of the bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition.
The bolts for cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 3 of 10
BUTTERFLY Range: NPS 3" to 6"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire water,
SERVICE
Hazardous Open Drain, Non Hazardous Open Drain, Sewage Water Treatment
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.5 CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7,8
OPERATOR Lever Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and valves to have locking facility to allow locking in the open, closed & all the intermediate position
by pad locks / Car seal arrangment without chains. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore
environment. Vendor shall provide relevant valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 4 of 10
BUTTERFLY Range: NPS 8" to 10"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire water,
SERVICE
Hazardous Open Drain, Non Hazardous Open Drain, Sewage Water Treatment
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.5 CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7,8
OPERATOR Gear Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide relevant
valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 5 of 10
BUTTERFLY Range: NPS 12" to 24"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire water,
SERVICE
Hazardous Open Drain, Non Hazardous Open Drain, Sewage Water Treatment
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.5 CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7,8
OPERATOR Gear Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide relevant
valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor to provide chord of the disc dimensions projecting beyond the valve body with the bid.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 6 of 10
BUTTERFLY Range: NPS 28" to 48"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A45B Notes
Offering
MATERIAL GROUP N/A
NACE REQUIREMENT NO
CORROSION ALLOWANCE 0 mm
Sea Water Lift & Distribution, Service Water Lift & Distribution, Fire water,
SERVICE
Hazardous Open Drain, Non Hazardous Open Drain, Sewage Water Treatment
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
PRESSURE RATING
16 barg -29°C to +85°C
DESIGN TEMP.
END CONNECTIONS To suit ASME B16.47 Series B CLASS 150 FF Flange 6, 10
BODY ASTM B148 C95800
DISC ECCENTRIC DISC TRIPLE OFFSET ASTM B148 C95800
SEAT INTEGRAL ASTM B148 C95800
SEAL RING GASKET UNS N10276 + Graphite 2
SEAL RING UNS N04400 + Graphite 2
SEAL RING RETAINING
ASTM B148 C95800
FLANGE / TAPER PIN
STEM MONEL K500
STEM SEAL / PACKING High Density Graphite 2
BOLTING MONEL K500 7,8
OPERATOR Gear Operator 3
MARKING MSS SP-25 5
INSPECTION & TESTS/
API 598 1, 4
ACCEPTANCE
TESTING Charpy test No
Leak test Yes
Torque test No
CERTIFICATIONS EN 10204 Type 3.1
PAINTING SYSTEM Doc No 200-20-CE-SPC-00001 "Painting Specification" 9
GENERAL SPECIFICATION Doc No 200-20-PI-SPC-00006 "Specification for Manual Valves" 1
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide relevant
valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor to provide chord of the disc dimensions projecting beyond the valve body with the bid.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. Inconel 625 (ASTM F468 Alloy 625 / ASTM F467 Alloy 625) material can be used for bolting.
9 Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.47 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 7 of 10
BUTTERFLY Range: NPS 3" to 6"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 8
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation
TYPE Through Drilled Lugs, Wafer Type
DESIGN ASME B16.34
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valvesdoc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and valves to have locking facility to allow locking in the open, closed & all the intermediate position
by pad locks / Car seal arrangment without chains. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore
environment. Vendor shall provide relevant valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 8 of 10
BUTTERFLY Range: NPS 8" to 10"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 8
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation
TYPE Through Drilled Lugs, Wafer Type
DESIGN ASME B16.34
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide relevant
valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor shall confirm in the bid that the mating pipe bore shall give adequate disc swing clearance.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003- Material Requirements for Sour Service
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 9 of 10
BUTTERFLY Range: NPS 12" to 24"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 8
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation
TYPE Double Flanged, Short Pattern, Blowout Proof
DESIGN ASME B16.34
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide
relevant valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor to provide chord of the disc dimensions projecting beyond the valve body with the bid.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625
(ASTM F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the
diameter, effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design
code of the bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition.
The bolts for cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.5 requirements.
DOC No 200-20-PI-DTS-00007
Make : Sheet: 10 of 10
BUTTERFLY Range: NPS 26" to 48"
Model : Revision: B
VALVES
Vendor
PIPING CLASS A6E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 8
CORROSION ALLOWANCE 3 mm
SERVICE Cooling Water Circulation
TYPE Double Flanged, Short Pattern, Blowout Proof
DESIGN ASME B16.34
FIRE SAFE DESIGN As per API 6FA or API 607 or ISO 10497
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any
conflicts or deviations shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seals shall be compatible with the service and design conditions indicated.
3. The valves shall be suitable for throttling and shall have locking mechanism to lock the valve at open/close and various intermediate disc
positions. All exposed items like thrust bearing,stop pins etc shall be suitable for Marine Offshore environment. Vendor shall provide relevant
valve detail drawings required for the design of valve locking.
4. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
5. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316
material shall be used for valve tagging.
6. Vendor to provide chord of the disc dimensions projecting beyond the valve body with the bid.
7. Vendor shall supply the bolts for the tapped holes where through bolting cannot be installed (as stem casing area) only in Inconel 625 (ASTM
F468) and shall be subject to COMPANY/CONTRACTOR approval. The tapped holes and bolts shall be identified with the diameter,
effective thread length and quantity on the relevant vendor drawing for each valve where required. Part list to include the design code of the
bolts at tapped holes. In addition Vendor shall guarantee the integrity of the bolted assembly for the specified design condition. The bolts for
cap screws shall be in accordance with Specification for Bolts, Nuts and Gaskets Doc no. 200-20-PI-SPC-00009
8. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-
00003 - Material Requirements for Sour Service
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting
Specification 200-20-CE-SPC-00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10 Flange face finish shall be in line with ASME B16.47 requirements.