Professional Documents
Culture Documents
200 20 Pi DTS 00005
200 20 Pi DTS 00005
D1BM APPLICABILITY
RGE Comp. Hub 6S
Comp. Hub 7S
Comp. Hub 8S
Comp. Hub 4S
RL Comp. Hub 1S
QG2 Comp. Hub 4N
Comp. Hub 6N
Swapnil
Lokesh, Jayaraman Kulkarni Cktan
Chee Seng Loh
2021.08.11 13:02:39 2021.08.11
15:43:45
2021.08.11 2021.08.11 16:27:00
16:01:43 +08'00'
+05'30' +08'00' +08'00'
C 2 7 Acronyms updated
C 7 11 References updated
HOLD LIST
Contents
1 INTRODUCTION ........................................................................................................................... 5
2 DEFINITIONS AND ACRONYMS ................................................................................................. 6
2.1 Definitions ............................................................................................................................ 6
2.2 Acronyms ............................................................................................................................. 6
3 PURPOSE OF DOCUMENT ......................................................................................................... 7
3.1 General ................................................................................................................................ 7
4 COMPACT DOUBLE BLOCK AND BLEED VALVES INDEX....................................................... 7
5 ORDER OF PRECEDENCE ......................................................................................................... 8
6 APPLICABLE CODES & STANDARDS ........................................................................................ 9
6.1 API–American Petroleum Institute....................................................................................... 9
6.2 ASME–American Society Of Mechanical Engineers ........................................................... 9
6.3 ASTM - American Society for Testing and Material ............................................................ 9
6.4 BSI–British Standards Institution ....................................................................................... 10
6.5 MSS–Manufacturers Standardization Society ................................................................... 10
6.6 NACE - National Association of Corrosion Engineers ....................................................... 10
7 REFERENCES ............................................................................................................................ 11
APPENDIX-1 (DATASHEETS FOR COMPACT DOUBLE BLOCK AND BLEED VALVES) ................ 12
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 3 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Figures
Figure 1-1: North Field Context ............................................................................................................... 5
Tables
Table 4-1 : Compact Double Block And Bleed Valves Index .................................................................. 7
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 4 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
1 INTRODUCTION
The reservoir pressure in Qatar’s North Field has been declining due to continuous production since
the early 1990s. The North Field is the world’s largest natural gas field and accounts for nearly all of the
state of Qatar’s gas production. The principal objective of the NFPS project is to sustain plateau from
existing QG South Operation – RL Dry Gas, RGE Wet gas and existing QG North Operation – QG1 &
QG2, production areas by implementing an integrated and optimum investment program consisting of
subsurface development, pressure drop reduction steps and compression. Refer to figure below for a
schematic of North Field.
Figure 1-1: North Field Context
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 5 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
Drilling and Looping Investments #1 and #2 are in execution phase and are being executed by I1P1
EPC, EPCO and EPCL projects with the exception of WHP13N, which will be part of NFPS
Compression project execution. The NFPS Compression Project involves the installation of large
offshore compression facilities at multiple locations. The compression facilities will be installed after the
completion of the Drilling and Looping Projects.
Qatargas Operating Company Limited is leading the development of the North Field Production
Sustainability (NFPS) Project. The principal objective of the NFPS project is to economically sustain
plateau from existing QG South (RGE, RL) and QG North (QG1 & QG2) production assets by
implementing an integrated and optimum investment program consisting of subsurface developments,
pressure drop reduction steps and offshore compression facilities installation.
CONTRACTOR is awarded to perform FEED for NFPS Compression Project – RGE, RL and QG2
Facilities.
2 DEFINITIONS AND ACRONYMS
2.1 Definitions
The following definitions used in the present PROJECT procedure are:
PROJECT NFPS Compression Project FEED
COMPANY Qatargas Operating Company limited
CONTRACTOR Middle East Projects International (Technip MEPI)
EPC CONTRACTOR CONTRACTOR engaged by COMPANY to execute EPC contract activities
or/and services
SUBCONTRACTOR A party who is providing subcontracted services specified and ordered by
CONTRACTOR or EPC CONTRACTOR
THIRD PARTY Third Party appointed by CONTRACTOR
VENDOR (SUPPLIER) A party who is responsible to manufacture and supply equipment and/or
services
SUB-VENDOR A party who is responsible to manufacture and supply equipment and/or
(SUB-SUPPLIER) services under responsibility of main VENDOR
SHALL The word “Shall” is to be understood as a mandatory requirement.
SHOULD The word “Should” is to be understood as strongly recommended.
MAY The word “May” is to be understood as an action to be undertaken at
CONTRACTOR / COMPANY ‘s discretion and upon evaluation of a review of
the circumstances of the issue in question.
2.2 Acronyms
The following acronyms are used in this document.
Term Description
API American Petroleum Institute
ASME American Society of Mechanical Engineers
ASTM American Society for Testing and Materials
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 6 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
3.1 General
This document covers the technical requirements for the Compact Double Block And Bleed Valves for
the offshore Topside Piping. This document shall be read in conjunction with Specification for Manual
valves document number 200-20-PI-SPC-00006 [3] and Valve selection philosophy Doc No: 200-20-
PI-DEC-00007[6].
4 COMPACT DOUBLE BLOCK AND BLEED VALVES INDEX
APPENDIX-1
VALVE VALVE END
PIPE CLASS DATASHEET
SIZE(INCH RATING CONNECTIONS
NUMBER
NPS 0.5" to 2" A34A 150 RF x NPTF 1 of 32
NPS 2" to 3" A34A 150 RF x RF 2 of 32
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 7 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
APPENDIX-1
VALVE VALVE END
PIPE CLASS DATASHEET
SIZE(INCH RATING CONNECTIONS
NUMBER
NPS 0.5" to 2" E5E 1500 RTJ x NPTF 3 of 32
NPS 2" E5E 1500 RTJ x RTJ 4 of 32
NPS 3" E5E 900 RTJ x RTJ 5 of 32
NPS 0.5" to 2" E7E 1500 RTJ x NPTF 6 of 32
NPS 2" E7E 1500 RTJ x NPTF 7 of 32
NPS 3" E7E 900 RTJ x RTJ 8 of 32
NPS 0.5" to 2" E34A 1500 RTJ x NPTF 9 of 32
NPS 2" E34A 1500 RTJ x RTJ 10 of 32
NPS 3" E34A 900 RTJ x RTJ 11 of 32
NPS 0.5" to 2" E37A 1500 RTJ x NPTF 12 of 32
NPS 2" E37A 1500 RTJ x RTJ 13 of 32
NPS 3" E37A 900 RTJ x RTJ 14 of 32
NPS 0.5" to 2" F7E1 1500 RTJ x NPTF 15 of 32
NPS 2" to 3" F7E1 1500 RTJ x RTJ 16 of 32
NPS 0.5" to 2" F11A 1500 RTJ x NPTF 17 of 32
NPS 2" to 3" F11A 1500 RTJ x RTJ 18 of 32
NPS 0.5" to 2" F25A 1500 RTJ x NPTF 19 of 32
NPS 2" to 3" F25A 1500 RTJ x RTJ 20 of 32
NPS 0.5" to 2" F34A 1500 RTJ x NPTF 21 of 32
NPS 2" to 3" F34A 1500 RTJ x RTJ 22 of 32
NPS 0.5" to 2" F37A 1500 RTJ x NPTF 23 of 32
NPS 2" to 3" F37A 1500 RTJ x RTJ 24 of 32
NPS 0.5" to 2" F37A (Metal seat) 1500 RTJ x NPTF 25 of 32
NPS 2" to 3" F37A (Metal seat) 1500 RTJ x RTJ 26 of 32
NPS 0.5" to 2" G7E 2500 RTJ x NPTF 27 of 32
NPS 2" to 3" G7E 2500 RTJ x RTJ 28 of 32
NPS 0.5" to 2" G11A 2500 RTJ x NPTF 29 of 32
NPS 2" to 3" G11A 2500 RTJ x RTJ 30 of 32
NPS 0.5" to 2" G37A 2500 RTJ x NPTF 31 of 32
NPS 2" to 3" G37A 2500 RTJ x RTJ 32 of 32
5 ORDER OF PRECEDENCE
In general the order of precedence shall be as follows:
a) Qatari Governmental and Regulatory Requirements
b) COMPANY Policies and Procedures
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 8 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
c) Project Specifications
d) Industry Codes and Standards
e) COMPANY and CONTRACTOR’S lessons learned
If CONTRACTOR / VENDOR deems any deviations from the specifications will result in significant
project cost and schedule saving, proposal to such deviations shall be submitted to COMPANY for
review and approval. CONTRACTOR / VENDOR shall not proceed with any deviation to the
Specifications without prior COMPANY APPROVAL.
6 APPLICABLE CODES & STANDARDS
The following codes, standards and specification referenced within the document shall be considered
as part of this specification. Conflict among applicable specification and / or codes shall be brought to
the attention of the COMPANY for resolution. COMPANY decision shall be final and shall be
implemented. The latest editions of codes and specification effective as on date of contract shall be
followed.
[1] API SPEC 6FA Specification for Fire Test for Valves
[3] API STD 607 Fire Test for Soft-Seated Quarter-Turn Valves
[2] ASME B16.5 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24
Metric/Inch Standard
[1] ASTM A105/A105M Standard Specification for Carbon Steel Forgings for Piping
Applications
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 9 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
[2] ASTM A182/A182M Standard Specification for Forged or Rolled Alloy and Stainless Steel
Pipe Flanges, Forged Fittings, and Valves and Parts for High-
Temperature Service
[3] ASTM A193 / A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for
High Temperature or High Pressure Service and Other Special
Purpose Applications
[4] ASTM A194 / A194M Standard Specification for Carbon and Alloy Steel Nuts for Bolts for
High Pressure or High Temperature Service, or Both
[5] ASTM A320 / A320M Standard Specification for Alloy-Steel and Stainless Steel Bolting for
Low-Temperature Service
[6] ASTM A350/A350M Standard Specification for Carbon and Low-Alloy Steel Forgings,
Requiring Notch Toughness Testing for Piping Components
[8] ASTM F467 Standard Specification for Nonferrous Nuts for General Use
[9] ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket
Head Cap Screws, and Studs for General Use
[1] MSS SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
[1] NACE MR0175/ISO 15156 Petroleum and Natural Gas Industries Materials for Use in H2S-
Containing Environments in Oil and Gas Production
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 10 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
7 REFERENCES
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 11 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
NFPS Compression Project FEED
THIS DOCUMENT IS PROPERTY OF QATARGAS. THIS DRAWING OR MATERIAL DESCRIBED THEREON MAY NOT BE
COPIED OR DISCLOSED IN ANY FORM OR MEDIUM TO THIRD PARTIES, OR USED FOR OTHER THAN THE PURPOSE Page 12 of 12
FOR WHICH IT HAS BEEN PROVIDED, IN WHOLE OR IN PART IN ANY MANNER EXCEPT AS EXPRESSLY PERMITTED
BY QATARGAS.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 1 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
Inlet Connection to suit ASME B16.5 CLASS 150 RF Flange, Outlet Connection with Threaded
END CONNECTIONS 3,4
(NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 2 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS A34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 150
DESIGN TEMP. -100°C to +175°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 150 RF Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 3 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 Gr.F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12 Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 4 of 32
COMPACT DOUBLE BLOCK Range: NPS 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 Gr.F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 5 of 32
COMPACT DOUBLE BLOCK Range: NPS 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E5E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT NO
CORROSION ALLOWANCE 3 mm
SERVICE Fuel Gas
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 900 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM A182 Gr.F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 Gr.F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 6 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 7 of 32
COMPACT DOUBLE BLOCK Range: NPS 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3,4
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 8 of 32
COMPACT DOUBLE BLOCK Range: NPS 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 900 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 9 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG - 900#)
SERVICE
(NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 10 of 32
COMPACT DOUBLE BLOCK Range: NPS 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG - 900#)
SERVICE
(NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 11 of 32
COMPACT DOUBLE BLOCK Range: NPS 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blow Down High Pressure Flare Piping (short segment BDV to Isolation valve) FG - 900#)
SERVICE
(NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -100°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 900 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 12 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas from
CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet Seperator up to
SERVICE
booster Pump Discharge, Comp. Suction Scrubber Pump Discharge, Diesel for Valve Flushing,
EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used
for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 13 of 32
COMPACT DOUBLE BLOCK Range: NPS 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas from
CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet Seperator up to
SERVICE
booster Pump Discharge, Comp. Suction Scrubber Pump Discharge, Diesel for Valve Flushing,
EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 14 of 32
COMPACT DOUBLE BLOCK Range: NPS 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS E37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS to Inlet Seperator, Gas from Inlet Seperator / Copm. Suction Scrubber, Gas from
CP1S(RL) Comp.Discharge Cooler to RT/RT2/PU Platform, Liquid from Inlet Seperator up to
SERVICE
booster Pump Discharge, Comp. Suction Scrubber Pump Discharge, Diesel for Valve Flushing,
EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 900
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 900 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used
for valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 15 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 16 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F7E1 Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 17 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT No
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A182 F316/316L 8
BALL Floating Ball, Solid Ball ASTM A182 F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 18 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT No
CORROSION ALLOWANCE 0 mm
SERVICE EG Flushing, Breathing Air
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -29°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A182 F316/316L 8
BALL Floating Ball, Solid Ball ASTM A182 F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 19 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP (Brownfield)
SERVICE
(NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 20 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F25A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
FWS from WHP/RP to CP (Brownfield & Greenfield),1500# Closed Drain at RP (Brownfield)
SERVICE
(NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 21 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP Inlet Header
(For - 1500#),Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve IN
SERVICE
Compression System (For - 1500#),PSV High Pressure Low Temperature Service (Only cover
for 1500# PSV at compressor discharge segment) (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 22 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F34A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve at CP Inlet Header
(For - 1500#),Blowdown High Pressure Piping (Short Segment BDV to Isolation Valve IN
SERVICE
Compression System (For - 1500#),PSV High Pressure Low Temperature Service (Only cover
for 1500# PSV at compressor discharge segment) (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING ASME Class 1500
DESIGN TEMP. -100°C to +204°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 23 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp. Discharge Cooler
to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser Platform,Gas from QG2
SERVICE
Compressor Discharge,Gas from QG2 Comp.Discharge Cooler to Riser Platform,Gas from
CP1S (RL) Compressor Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 24 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp. Discharge Cooler
to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser Platform,Gas from QG2
SERVICE
Compressor Discharge,Gas from QG2 Comp.Discharge Cooler to Riser Platform,Gas from
CP1S (RL) Compressor Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 25 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp. Discharge Cooler
to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser Platform,Gas from QG2
SERVICE
Compressor Discharge,Gas from QG2 Comp.Discharge Cooler to Riser Platform,Gas from
CP1S (RL) Compressor Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
Inlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625 12
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be equal to 400 μm
minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
13. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 26 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS F37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
Closed Drain Pump ,Gas from RGE Comp.Discharge,Gas from RGE Comp. Discharge Cooler
to discharge SDV,Gas from RGE Comp.Discharge SDV to Riser Platform,Gas from QG2
SERVICE
Compressor Discharge,Gas from QG2 Comp.Discharge Cooler to Riser Platform,Gas from
CP1S (RL) Compressor Discharge, Diesel for Valve Flushing, EG for Valve Flushing (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 1500
DESIGN TEMP. -46°C to +204°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 1500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625 12
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Seats and ball contact faces shall be Tungsten Carbide coated.The thickness of the Tungsten Carbide coating, after grinding and lapping, shall be equal to 400 μm
minimum. The minimum hardness shall be 1050 HV. Coating process shall be HVOF (High Velocity Oxygen Fuel)
13. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 27 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +85°C
Inlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 28 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G7E Notes
Offering
MATERIAL GROUP Group 1.1
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 12
CORROSION ALLOWANCE 3 mm
SERVICE Closed Drain (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +85°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A350 LF2 Cl.1 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
13. Bolting, including nuts shall be coated as per 200-20-PI-SPC-00009 - Specification for Bolts,Nuts and Gaskets.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 29 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT No
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -29°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM A182 F316/316L 8
BALL Floating Ball, Solid Ball ASTM A182 F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 30 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G11A Notes
Offering
MATERIAL GROUP Group 2.2
NACE REQUIREMENT No
CORROSION ALLOWANCE 0 mm
SERVICE MEG Injection, CI Injection, Diesel for Valve Flushing
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve (Bleed)
TYPE
and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -29°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM A182 F316/316L 8
BALL Floating Ball, Solid Ball ASTM A182 F316
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat ASTM A182 F316
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-
00001. Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 31 of 32
COMPACT DOUBLE BLOCK Range: NPS 0.5" to 2"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
Compact Double Block & Bleed Valve w/outlet 1/2" Thd-OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
Inlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange, Outlet Connection with
END CONNECTIONS 3,4
Threaded (NPTF)
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service.
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.
DOC No 200-20-PI-DTS-00005
Make : Sheet: 32 of 32
COMPACT DOUBLE BLOCK Range: NPS 2" to 3"
Model : Revision: C
AND BLEED VALVES
Vendor
PIPING CLASS G37A Notes
Offering
MATERIAL GROUP Group 3.8
NACE REQUIREMENT YES AS PER MR0175/ISO 15156 9
CORROSION ALLOWANCE 0 mm
SERVICE Liquid from Export Pump Discharge HIPPS Valve (NACE)
Compact Double Block & Bleed Valve w/outlet Flanged -OS&Y Globe type Needle valve
TYPE
(Bleed) and Ball type isolation valves (Primary & Secondary Block)
DESIGN ASME B16.34 / Manufacturer standard 10
END TO END DIMENSION
Manufacturer Standard
STANDARD
FIRE SAFE API 6FA or API 607 or ISO 10497
PRESSURE RATING Class 2500
DESIGN TEMP. -46°C to +94°C
END CONNECTIONS Inlet & Outlet Connection to suit ASME B16.5 CLASS 2500 RTJ Flange 3
BODY Compact Design with One Piece Body ASTM B564 UNS N06625 8
BALL Floating Ball, Solid Ball ASTM B564 UNS N06625
BODY SEAL Primary Seal & Firesafe Secondary Seal AED Type & Suitable for Service 2
STEM Anti blow out - Non Rotating Stem Integral Seat UNS N07718
NOTES :
1. Valves shall be provided in accordance with this Valve Data Sheet and Specification for Manual Valves doc no, 200-20-PI-SPC-00006. Any conflicts or deviations
shall be brought to COMPANY’s attention for resolution.
2. Soft materials used for seats and seals shall be AED type and compatible with the service and design conditions indicated.
3. Flange face finish shall be in line with ASME B16.5 requirements.
4. Threaded end connection shall be in line with ANSI/ASME standard B1.20.1 requirements.
5. A differential hardness of at least 50 HB points between metal to metal mating surfaces is required to prevent galling.
6. Hydrostatic test pressure shall be based on pressure rating as per ASME B 16.34.
7. All valves shall be marked as per applicable specifications and in addition shall be marked with valve tag number by die stamping, SS316 material shall be used for
valve tagging.
8. Mating nuts and threaded stud recesses shall be tapped oversize to the extent necessary to prevent damage to the coating on fastener during assembly.
9. All metallic components in contact with production fluids shall comply with ISO 15156/NACE MR0175 requirements and 200-20-CE-SPC-00003 - Material
Requirements for Sour Service
10. Bore for primary & secondary ball valve shall be 10 mm (min)
11. Painting detail requirements and Acceptable Paint Manufacturers and Product Identification shall be in accordance with Painting specification 200-20-CE-SPC-00001.
Any conflicts or deviations shall be brought to COMPANY’s attention for resolution.
12. Gaskets & Bolting shall be in accordance with Specification for Bolts, Nuts and Gaskets doc no, 200-20-PI-SPC-00009.