Professional Documents
Culture Documents
Pack 11
Editorial by: Milanoedit srl, milanoedit.com
Translation by: TperTradurre
Picture credits: NBCUniversal Archive
©️ 2019 Universal City Studios LLC.
Fast & Furious and all related marks and characters are trademarks Stage 41
and copyrights of Universal Studios.
All Rights Reserved. Attaching the rear axle
Dodge, HEMI and related logos, vehicle model names and trade
Stage 42
dress are trademarks of FCA US LLC and used under license by
Premium and Collectibles Trading Co. Ltd. ©2019 FCA US LLC.
Mounting the right rear
© 2019 Editorial Planeta DeAgostini S.A.U.
Todos los derechos reservados. wheel
© 2019 De Agostini Publishing Italia S.p.A. Stage 43
Tutti i diritti riservati.
Warning: Not suitable for children under the age of 14. Assembling the battery
This product is not a toy and is not designed or intended for use
in play.
holder I
Items may vary from those shown. Stage 44
41E 41F HM IM
This in no way affects the quality or assembly instructions.
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
161
STAGE 41
41.1
Get the chassis and very
35C carefully put it upside down on
your work surface. Find the end
of the gear box and insert the linchpin on the
front coupling 35C (i.e. the coupling with the
smallest diameter), as shown in the
illustration.
12C
12D
40G 40G
41.2
Insert the two rear shock absorber cylinders 40F into the 40F 40F
holes indicated in the illustration, then secure with two type
AM screws. Insert a spring 40G into each of the two shock
absorber cylinders 40F.
AM
31A
39C
41.3
Take the rear axle complete
with the leaf springs. Align the
38F ends of the leaf springs with the
chassis: the two rear reinforcement plates 38F and
39F go above the holes in the rear section of the
chassis 31A, while the front reinforcement
plates 38C and 39C line up with the holes in the
middle section of the chassis 30A. Insert the
linchpin on the rear coupling 35D into the
corresponding hole in the rear differential 36B.
Attention: you will also have to deal with the shock
absorbers in this assembly session, as illustrated in the
30A next step.
35D
31A
162
STAGE 41
37H
34E
40E
41.4
40E As you attach the rear axle to the
chassis, insert the rear shock
34E absorbers rods 40E into their
respective cylinders 40F. At this point, you can attach
40F the free end of the rear brake hose 34E to the linchpin
on the rear brake hose fitting 37H.
40F
AM
AM
FM FM
41.5
Turn the assembled piece over and insert
four type AM screws into the mounting
holes in the rear end of the chassis, then four
type FM screws into the holes in the middle.
31A
41.6
Note that one side of the tyre 41A has «inside» written on it, and the other side has «outside»
on it. Slide the tyre valve 41C onto the small linchpin on the outside of rim 41B, and put the latter
on the outside of the tyre. Insert the inside of the rim 41D into the inside of the tyre 41A, and align
30A
the holes and linchpins of the two parts of the rim. Secure the two pieces with three type HM screws. You have now
completed the left rear wheel.
41B 41B
41D
41C
HM
41A
HM
163
STAGE 41
41B
36A
41E IM 41F
41E
41.7
Slide the wheel you have just assembled onto the left end of the rear axle, and secure it with a washer 41F and a
type IM screw. Finally, press the hub cover 41E onto the middle of the wheel.
164
MOUNTING THE RIGHT STAGE 42
REAR WHEEL
In this assembly session you will assemble the right rear wheel and attach it to the corresponding side of your
model’s rear axle.
42E 42F HM IM
This in no way affects the quality or assembly instructions.
42A Rear right tyre 42D Rim (inside) HM Screws 2×3 mm (x 4)*
42B Rim (outside) 42E Hub cover IM Screws 2.5×5 mm (x 2)*
42C Tyre valve 42F Washer
* Some of the parts are spares.
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
165
STAGE 42
42B
42.1
Slide the tyre valve 42C onto the
small linchpin on the outside of the rear
right tyre rim 42B.
The tyre markings have been faithfully reproduced on all four tyres
of your model.
42.2
Note that one side of the tyre 42A has «inside» written on it,
and the other side has «outside» on it. Put the outside of the rim
42B on the outside of the tyre. Join the two pieces.
42B
42A
166
STAGE 42
42.3
Insert the inside of the rim 42D into the inside of the 42B
tyre 42A, and align the holes and linchpins of the two
parts of the rim. Secure the two pieces with three type HM
screws. The right rear wheel is now ready to mount on your model.
HM
HM
42D 42A
HM
42.4
Slide the wheel you have just assembled onto the right end of the rear axle 36A. Put a washer 42F onto the
middle of the wheel and secure it with a type IM screw. Don’t tighten it too much, otherwise the wheel won’t
move freely.
42B
36A
42F
IM
167
STAGE 42
42.5
Finally, press the hub cover 42E onto
the middle of the outside of the rim 42B.
42E
42B
168
ASSEMBLING THE 43 STAGE
43B
Publisher Note: the appearance of the parts shown on these pages may differ from that of the pieces included in this pack.
43A
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
169
STAGE 43
43C
43.1
From the top side of the battery holder
cover 43B, insert the screw 43C into the
corresponding hole.
AN OVERVIEW
The battery holder will go at the back of the chassis, and can be opened
by removing the screw that comes with this stage.
To operate your model’s electrical system, you will need three batteries to
power the lighting system and produce the sound effects. These must be
connected to a control unit and a speaker, located in the central part of the
chassis. The small hole in the fuel tank will house a switch, which you can use
to turn your model’s electrical functions on and off whenever you like.
43B
Engine block
Front section
of the chassis
Speaker holes
170
STAGE 43
43D
43.2
Turn the battery holder cover over and slide the
43C spring 43D onto the screw.
43B
Battery holder
171
STAGE 43
43E
43C
43D
43.3
Finally, slide the washer 43E onto the screw
43C so that it is on top of the spring 43D.
43B
172
ASSEMBLING 44 STAGE
44B 44C EP FP GP
44A Battery holder with wires and switch FP Screws 2.3×4 mm (x 5)*
44B Connecting plate GP Screws 1.2×3 mm (x 3)*
44C Hex nut
EP Screws 1.7×3 mm (x 3)* * Some of the parts are spares.
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
173
STAGE 44
44C
44.1
Insert the nut 44C into the
corresponding hexagonal hole in
the battery holder 44A.
44A
GP
44.2
Place the connecting plate 44B over the nut 44C and
secure it with two type GP screws.
44B
44A
44C
174
STAGE 44
FP FP
44.3
Join the piece you have just assembled
44A with the back panel of the fuel tank 43A.
Insert the switch correctly into the small
rectangular hole, as shown in the illustration. Secure the pieces
with four type FM screws.
43A
EP
43A
44.4
Secure the switch with two type
EP screws.
44A
175
STAGE 44
43B
44.5
Get the battery holder cover
43B. Put it on top of the battery
holder, using the two tabs. Secure
with the screw 43C.
43C
43A
176
THE FUEL TANK AND STAGE 45
THE SPEAKER
In this assembly session you will assemble the fuel tank and attach the speaker to the chassis.
AP
This in no way affects the quality or assembly instructions.
CM CP
FUELserbatoio
TANK AND SPEAKER
e altoparlante
These items are not toys; keep out of reach of children. The product is part of an assembly kit intended for an adult audience.
Assemble with the utmost care following the instructions in the attached manual; modifications or tampering are prohibited. Made in China. Read and keep for further reference.
177
45A
44A
45.1
Get the piece with the battery
holder. Pass the wiring through
the rectangular hole in the upper
panel of the fuel tank 45A, and attach the latter to
the lower panel 43A by joining the respective
linchpins together.
AP
AP 43A
AP
45.2
Secure the two parts of the fuel tank with
six type AP screws.
45A
178
45.3
CP Get the chassis and, from
underneath, put the fuel tank
CP in position. Make sure the
battery holder wiring comes out on top and align
the mounting holes. Secure with four CP type
screws.
31A
44A
45A
43A
45.4
Locate the circular housing shown in the illustration. Insert the
speaker 45B, ensuring it faces exactly the same way as that shown in
the illustration.
45B
30A
179
CM
45.5
Position the retainer ring 45C as shown in the
illustration. Align the fixing holes and secure the
pieces with two type CM screws.
45C
45B
30A
180