Professional Documents
Culture Documents
2
10mm
Housing : Black ABS plastic. 1 To set the Function: To set the point of the
4 1 3
Operating Instructions Front cover : Polycarbonate plastic.
Set point controller.
Dimensions : Front - 75 X 34.5 mm, Depth 71 mm (w/o back lid).
Panel Cutout : 29 X 71 mm Press & hold Display will show t1 & flash.
Mounting : Flush panel mounting with fasteners. To go to other parameters, use
Panel cutout
SET
71mm
Protection : IP65 Frontal. UP/DOWN keys.
R1 0 34.5mm Connections : Screw terminal blocks. key for
C
% RH < 2.5sq mm one wire/terminal only. 2 Seconds.
R2
Display : 3X10 mm (0.39") LED. 2 t1 Parameter Function: To set the cut out point of the
prg SET
Data storage : Non-volatile EEPROM memory controller for Temp.
Power input : 230Vac +/-10%, 50-60Hz. Others on request.
SZ-9912 19mm 71mm O O
To change value use keys To set value press key
29mm Operating temp.: 5 C to 50 C(non-condensing).
O O
Storage temp : -20 C to 70 C(non-condensing).
PANEL Side Lock
Range : RH : 30 to 90% (SZ-9912) Display will show set value & flash. The set point value can
RH : 0 to 99% (SZ-9922) now be changed by using the UP/DOWN key. After setting
O
R1 0
: Temperature : 0 to 99.9 C the desired value, press the set key and you will see “_ _ _"
C O
% RH GASKET Resolution : 1% for Humidity, 0.1 C for Temperature. which confirms that the set point has been stored in memory.
R2 Accuracy : +/-5% for Humidity, +/-0.1OC for Temp. (SZ-9912)
prg SET O
+/-3% for Humidity,+/-0.1 C for Temp. (SZ-9922) Min Max Fac.
Output : R1,R2 8(3)A/250Vac
Input : Humidity Sensor(SZ-HS-220) for SZ-9912
P3+1 P2-1 40.0OC
SZ-9922
Humidity Sensor(SZ-HS-100) for SZ-9922 3 t2 Parameter Function: To set the cut out point of the
Temperature Sensor(RTD)
Temperature + Humidity Controller controller for Humidity
USER INTERFACE Display will show value & flash. The set point value can now be
In Program mode: changed by using the UP/DOWN key. After setting the desired
Introduction : UP
Scroll through parameters & Increases value, press the set key and you will see “_ _ _" which confirms
The SZ-9912 and SZ-9922 is two set point controller. One is for CONTROLLER
parameter value. that the set point value has been stored in memory.
Humidity control and another is for Temperature control.
Press and hold for 2sec to enter into program Min Max Fac.
Suggested Wiring SZ-9912 Down/
A number of parameters are displayed alphanumerically to set the Program mode. H3+1 H2-1 70%
controller for specific application. RH TEMP. SZ-HS-220 In program mode: Decreases parameter value
4 EP Parameter Function: To end programming.
RELAY2 RELAY1 RH INPUT RTD INPUT In program mode : set/save the changed
This controller can be used for several applications with a measuring NO C NO C 9Vac G B R R W W Set
O O
value of parameter. To end Once the key is pressed, the controller
Humidity range from 30% to 90% RH. and 0 C to 99.9 C 1 2 3 4 5 6 7 8 9 10 11 12 programming goes into the normal mode and displays
temperature range for SZ-9912. 0
C Temp. / This key used to changed the display between press "SET" key the temperature / humidity and all settings
Humidity range from 0% to 99% RH. and 0OC to 99.9OC temperature % RH RH Temperature and RH. are recorded.
range for SZ-9922.
INDEX 5 To set other Display will flash “P1”.
CAUTION Parameters. To select other parameters, use
Sr. Description
WIRING: The probe and its corresponding wires should never be installed Para. UP/DOWN keys.
Compressor, Contacter
Compressor, Contacter
Compressor, Contacter
the perimeter of the panel cut out or a rubber ‘O’ ring supplied before the
unit is fitted to increase protection against water seepage. 18 LP Keypad lock.
Min Max Fac.
19 EO Switch display between Temp. & Humidity. O O O
Controller :Controller should be installed in a place protected by (Message on display) XX C 99.9 C 99.9 C
vibration, water and corrosive gasses and where ambient temperature 20 E1 Display selection Temp. & Humidity.
does not exceed the values specified in the technical data. XX = Set Point+1
Phase 21 FS Restore Default Setting controller.
Probe :To give a correct reading, the probe must be installed in a place
protected from thermal influences, which may affect the temperature to be 22 EP End Programming
controlled. Neutral 23 LED Indications
24 Operating Messages
8 P3 Parameter Function: To set minimum allowable low 13 H2 Parameter Function : To set maximum allowable high 18 LP Parameter Function: To lock keypad. 24 OPERATING MESSAGES
temperature set point. humidity limit.
Once set at a particular value, this will not allow the set point to Once set at a particular value, this will not allow the set point to go
This parameter is used to lock the keypad so that tampering is not Ht High temperature alarm Lt Low temperature alarm
possible by by-standers. Temperature above the Temperature below the
go below this value. above this value and below set point setting. maximum high minimum low
0 = keypad unlocked
Example : Setting this parameter at 20.0OC will not allow the Example : Setting this parameter at 80% will not allow the set temperature limit (P2). temperature limit (P3).
1 = keypad locked
set point to go below 20.0OC. Also, if the temperature/humidity point to go above 80%. Also, if the humidity reaches 80% the
reaches 20.0OC, the display will show Lt (LowTemp.) indicating display will show HH (High Humidity) indicting that the Humidity When locked all parameters can only be viewed, but not HH High humidity alarm LH Low humidity alarm
that the temperature/humidity has gone below the value in this has gone above the range in this parameter. modified. Humidity above the Humidity below the
parameter. Min Max Fac. maximum limit of the minimum limit of the
Min Max Fac. SZ-9912 SZ-9922 ON set value (H2) set value (H3)
Min Max Fac. Min Max Fac. Keypad Locked 0 1 1
(Message on display) 0.0 C
O
XXOC-1 0.0 C
O
To compensate for this error, you may need to add or minus the When set to 1 all parameters are programmed to factory values.
This parameter is used to protect the compressor from Useful to debug setting related problems.
restarting in a short period of time and can be set between 0 to %RH required to achieve the correct Humidity.
20 minutes. Example : The Humidity on the display is 40%, whereas the Min Max Fac. Cold Room Controller Ball Valves
Example : If this parameter is set at 3 minutes, the relay will cut actual Humidity is 42%. You will need to set the H5 parameter to 0 1 0 Chiller Controller Globe Valves
off at the set temperature, but will not restart for a minimum of 3 2, which means that once out of the programming mode, the Two Compressor Controller Hand Valves
Humidity will show 42%(40% + 2%). 22 EP Parameter Function: To end programming. Heating Controller
minutes, even if the differential is achieved earlier. This Flow Switches
parameter is good to protect the life of the compressor when Min Max Fac. Humidity Controller
To end Once the key is pressed, the controller goes Solenoid Valves
there are power fluctuations and the compressor is switched -10% 10% 0% programming Pressure Controller
into the normal mode and displays the
off and on within a few seconds. press "SET" key temperature and all settings are recorded. 03 / 07.06.17
17 H6 Parameter Function: To set time delay between relay
Min Max Fac.
restart time. 23
Flashing 0 Min 20 Min 1 Min LED INDICATION
Time delay in progress This parameter is used to protect the De-Humidifier from
12
3 H1 Parameter Function: To set controller in restarting in a short period of time and can be set between 0 to 20 R1 Temperature Relay R2 Humidity Relay
minutes. ON: Temperature relay ON: Humidity relay is
Dehumidification / Humidification Mode.
Example : If this parameter is set at 1 minutes, the relay will cut is ON. ON.
0 = Dehumidification. off at the set Humidity, but will not restart for a minimum of 1 OFF: Temperature relay OFF: Humidity relay is
Min Max Fac. is OFF. OFF.
1 = Humidification. minutes, even if the differential is achieved earlier. This
0 1 0 parameter is good to protect the life of the Dehumidifier / FLASHING : FLASHING :
Temperature relay Humidity relay is
Humidifier or even in applications where the probe is placed at
is in time delay. in time delay.
places where there are sudden & short changes in Humidity.