Professional Documents
Culture Documents
Trainer Name:
Tick the multiple-choice questions - Give short answer where there is no multiple choice
Turn off your mobile phone before attending your exam
HARDWARE BASICS
2)If dust particle in optics what will be the likely output on digital copier
A) Dark copies B) Light copies C) no image D) error code
6)Define CIS -
7)Define is CCD
8)which is the simulation mode for checking the scanning motor speed.
A) U065 B) U073 C) U191 D) U201
2|Page
15)There is no need of clean a primary roller charger because the material is conductive
plastic (True or False)
18)The Laser unit switch _____the Black Pixel and switch _____for the White Pixel (ON
& OFF)
21)The toner converts the __________image on the imaging drum surface into a
_________Image. (visible, latent)
24)To separate the paper from the drum which component we are using in copiers
(Separator or Transfer roller)
34)What is the simulation mode to reset the Fuser Counter in TA-3051ci Machine.
a)U163 b)U167 c)U197 d)U251
39)Define IH: -
41)What should be the output color when you mix CYAN, MAGENTA and YELLOW?
43)What kind of color mixing technology is been used in Kyocera color devices?
1)additive mixing 2) black mixing 3) subtractive mixing 4) none of these.
46)Which component below are related to LASER unit - Tick the correct answers.
a) Magnetic roller
b) Beam detection sensor
c) Polygon mirror
d) Exposure lamp
47)What will be the output image if a main charger is missing on the imaging unit?
a) blank image b) Red image c) black image d) normal image
49)Which simulation from service mode is used to check the motor operations in a MFD?
50)Scenario: You are getting white sharp thick bands on the output image, what are the
possible reasons for this?
7|Page
54)What are the possible causes of getting faint image while copying?
55) Why do we need a waste toner tank in the MFD? Give one sentence answer.
58) What is Rx command center and explain four features related to configuration?
59) Mention one model each from a mono and color device with 30 ppm?
60)Which are the three rollers in feed assembly? Mention all three.
8|Page
65) What is the maximum capacity of cassette 1 in a TA 3050 ci with 75 gsm paper?
450 ; 350 ; 500 ; 200
70) Which paper source is recommendable for printing Thick paper media/ Card Stoke?
Cassette 1 ; Document processer ; Multipurpose tray ; Optional tray.
72)In the event log you have seen code J9006 , what is it related to?
Cassette 1 Jam ; Bypass cassette jam ; Conveying unit jam ; Document processor jam
74) Which is the simulation in service mode using for initialization of Touch panel?
U 167 ; U 201 ; U 199 ; U119
9|Page
75) If you are suspecting a clutch problem in device through which simulation do you test?
U 21; U 32 ; U 31; U 24
78) Through which utility you can do the color registration in a color device?
Printer settings; Device common settings; Adjustment/maintenance; Function settings.
79)Scenario: You are in the site to attend a service call for a MFD , which is the best and
easiest way to know the history and to diagnose the fault.
82) Which are the types of storage in device? Select multiple answers -
Compact flash; Hard disc; Secure Digital card; USB disc; Solid State Drive.
A) Lower pulley switch b) Loop switch c) loop sensor d) Low power section
a) Eco Print is ON
b) HEAT ROLLER has toner stain
c) Main charger Faulty
d) M1, M2, M3, mirrors have dust
11 | P a g e
88)Imagine Gear A rotates in clockwise then what is the direction of Gear C rotation...?
(Clockwise or Anticlockwise)
89)Imagine the below stretches trolley moving front, so what is the direction of wheel B rotation ..?
A) Clockwise
B) Anticlockwise
94)Please choose the roller which helps to carry the toner from DEV unit to DRUM.
A) Main charger
B) Mag roller
C) Spiral
D) Sec transfer Roller
95)Please write the interface names for 17 & 20 (form the below image)
96)There is no need of removing the toner containers to check main chargers in TA-3051Ci.
A) True
B) False
97)Right door unit must be removed to service transfer belt assy in TA-3051Ci
A) True
B) False
A) Boot ROM
B) RAM
C) EEPROM
D) HDD