Professional Documents
Culture Documents
Version 6.50
Revision B
June 2013
Part Number 71504-00-ENG
71504-00-ENG
Contact Information the nonconforming Product with new, equivalent to new, or
Trimble Navigation Limited reconditioned parts or Product, OR refund the Product purchase
Trimble Agriculture Division price paid by you, at Trimble’s option, upon your return of the
10355 Westmoor Drive Product in accordance with Trimble's product return procedures
Suite #100 then in effect.
Westminster, CO 80021
USA How to Obtain Warranty Service
trimble_support@trimble.com To obtain warranty service for the Product, please contact your
Legal Notices local Trimble authorized dealer. Alternatively, you may contact
Trimble to request warranty service at +1-408-481-6940 (24 hours
Copyright and Trademarks a day) or e-mail your request to trimble_support@trimble.com.
© 2009-2013, Trimble Navigation Limited. All rights reserved. Please be prepared to provide:
– your name, address, and telephone numbers
Trimble, the Globe and Triangle logo, AgGPS, EZ-Boom, EZ-Guide, – proof of purchase
EZ-Steer, FmX, and Tru Count Air Clutch are trademarks of Trimble – a copy of this Trimble warranty
Navigation Limited, registered in the United States and in other – a description of the nonconforming Product including the model
countries. Autopilot, Field-IQ, FieldManager, FM-1000, Rawson, number
TrueGuide, TrueTracker, and Tru Application Control are – an explanation of the problem
trademarks of Trimble Navigation Limited. GreenSeeker is a
The customer service representative may need additional
registered trademark of NTech Limited. information from you depending on the nature of the problem.
All other trademarks are the property of their respective owners.
This product is covered by the following United States Patent Warranty Exclusions and Disclaimer
Numbers: 5,311,149, 5,369,589, 5,987,383, 6,252,863, 5,402,450, This Product limited warranty shall only apply in the event and to
5,493,588, and 6,463,374. Other patents pending. the extent that (a) the Product is properly and correctly installed,
configured, interfaced, maintained, stored, and operated in
Release Notice accordance with Trimble's applicable operator's manual and
This is the June 2013 release (Revision B) of the FmX Integrated specifications, and; (b) the Product is not modified or misused.
This Product limited warranty shall not apply to, and Trimble shall
Display Cabling Guide. It applies to version 6.50 of the FmX not be responsible for, defects or performance problems resulting
integrated display firmware.
from (i) the combination or utilization of the Product with
LIMITED WARRANTY TERMS AND CONDITIONS hardware or software products, information, data, systems,
interfaces, or devices not made, supplied, or specified by Trimble;
Product Limited Warranty (ii) the operation of the Product under any specification other
Trimble Navigation Limited (“Trimble”) warrants that this product than, or in addition to, Trimble's standard specifications for its
and its internal components (the “Product”) shall be free from products; (iii) the unauthorized installation, modification, or use of
defects in materials and workmanship and will substantially the Product; (iv) damage caused by: accident, lightning or other
conform to Trimble’s applicable published specifications for the electrical discharge, fresh or salt water immersion or spray
Product for a period of two (2) years, starting from the earlier of (i) (outside of Product specifications); or exposure to environmental
the date of installation, or (ii) six (6) months from the date of conditions for which the Product is not intended; (v) normal wear
original Product shipment from Trimble. and tear on consumable parts (e.g., batteries); or (vi) cosmetic
damage. Trimble does not warrant or guarantee the results
obtained through the use of the Product, or that software
Product Software components will operate error free.
Product software, whether built into hardware circuitry as NOTICE REGARDING PRODUCTS EQUIPPED WITH TECHNOLOGY
firmware, provided as a standalone computer software product, CAPABLE OF TRACKING SATELLITE SIGNALS FROM SATELLITE BASED
embedded in flash memory, or stored on magnetic or other AUGMENTATION SYSTEMS (SBAS) (WAAS/EGNOS, AND MSAS),
media, is licensed solely for use with or as an integral part of the OMNISTAR, GPS, MODERNIZED GPS OR GLONASS SATELLITES, OR FROM
Product and is not sold. If accompanied by a separate end user IALA BEACON SOURCES: TRIMBLE IS NOT RESPONSIBLE FOR THE
license agreement (“EULA”), use of any such software will be OPERATION OR FAILURE OF OPERATION OF ANY SATELLITE BASED
subject to the terms of such end user license agreement (including POSITIONING SYSTEM OR THE AVAILABILITY OF ANY SATELLITE BASED
any differing limited warranty terms, exclusions, and limitations), POSITIONING SIGNALS.
which shall control over the terms and conditions set forth in this THE FOREGOING LIMITED WARRANTY TERMS STATE TRIMBLE’S ENTIRE
limited warranty. LIABILITY, AND YOUR EXCLUSIVE REMEDIES, RELATING TO THE TRIMBLE
PRODUCT. EXCEPT AS OTHERWISE EXPRESSLY PROVIDED HEREIN, THE
Software Fixes PRODUCT, AND ACCOMPANYING DOCUMENTATION AND MATERIALS ARE
During the limited warranty period you will be entitled to receive PROVIDED “AS-IS” AND WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY
KIND, BY EITHER TRIMBLE OR ANYONE WHO HAS BEEN INVOLVED IN ITS
such Fixes to the Product software that Trimble releases and CREATION, PRODUCTION, INSTALLATION, OR DISTRIBUTION, INCLUDING, BUT
makes commercially available and for which it does not charge NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
separately, subject to the procedures for delivery to purchasers of FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NONINFRINGEMENT. THE
Trimble products generally. If you have purchased the Product STATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR
from an authorized Trimble dealer rather than from Trimble LIABILITIES ON THE PART OF TRIMBLE ARISING OUT OF, OR IN CONNECTION
directly, Trimble may, at its option, forward the software Fix to the WITH, ANY PRODUCT. BECAUSE SOME STATES AND JURISDICTIONS DO NOT
Trimble dealer for final distribution to you. Minor Updates, Major ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED
Upgrades, new products, or substantially new software releases, WARRANTY, THE ABOVE LIMITATION MAY NOT APPLY OR FULLY APPLY TO
as identified by Trimble, are expressly excluded from this update YOU.
process and limited warranty. Receipt of software Fixes or other
enhancements shall not serve to extend the limited warranty Limitation of Liability
period. TRIMBLE'S ENTIRE LIABILITY UNDER ANY PROVISION HEREIN SHALL BE
For purposes of this warranty the following definitions shall apply: LIMITED TO THE AMOUNT PAID BY YOU FOR THE PRODUCT. TO THE
(1) “Fix(es)” means an error correction or other update created to MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL
fix a previous software version that does not substantially conform TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL,
to its Trimble specifications; (2) “Minor Update” occurs when INCIDENTAL, OR CONSEQUENTIAL DAMAGE WHATSOEVER UNDER ANY
CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANYWAY TO THE PRODUCTS,
enhancements are made to current features in a software SOFTWARE AND ACCOMPANYING DOCUMENTATION AND MATERIALS,
program; and (3) “Major Upgrade” occurs when significant new (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS
features are added to software, or when a new product containing PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA, OR ANY OTHER
new features replaces the further development of a current PECUNIARY LOSS), REGARDLESS OF WHETHER TRIMBLE HAS BEEN ADVISED
product line. Trimble reserves the right to determine, in its sole OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF
discretion, what constitutes a Fix, Minor Update, or Major DEALING WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND
Upgrade. TRIMBLE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR
Warranty Remedies INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
If the Trimble Product fails during the warranty period for reasons PLEASE NOTE: THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS
covered by this limited warranty and you notify Trimble of such WILL NOT APPLY TO PRODUCTS PURCHASED IN THOSE JURISDICTIONS
failure during the warranty period, Trimble will repair OR replace (E.G., MEMBER STATES OF THE EUROPEAN ECONOMIC AREA) IN
WHICH PRODUCT WARRANTIES ARE THE RESPONSIBILITY OF THE LOCAL
In this chapter:
Multiple cables on single ports This chapter includes guidelines on cabling
options for the Trimble® FmX® integrated
Cable/port compatibility table
display.
Superseded cables
• The replicator port on most cables breaks away the pins not used by the primary device the cable
was designed for. For example, if the RS232 port is required, the port replicator breaks out the
CAN, digital pins, and so on. Do not connect the port replicator to the NavController II.
• Lightbars, the Field-IQ™ crop input control system, Tru Application Control™, the FieldLevel II
system, the EZ-Steer® assisted steering system, yield monitoring and the EZ-Boom® automated
application control system require their own dedicated CAN ports.
• The Autopilot™ automated steering system, the TrueTracker™ implement steering system, the EZ-
Steer system, and radar output must be connected to port C or D.
• The Ag3000 modem can only be connected to port D.
• When using yield monitoring with CAN, only connect to port A.
• When using the LB25 lightbar and cable P/N 72420, you must use port B with internal
termination.
c e
d f
Superseded cables
Cable updates since the previous FmX integrated display release are as follows:
In this chapter:
Standalone FmX / WAAS / EGNOS / The FmX integrated display can operate as a
OmniSTAR XP/HP corrections standalone guidance system, or you can connect
it to a range of agricultural guidance devices to
Standalone FmX / RTK corrections
expand its functionality. This document shows
you how to complete those cable connections.
g c
f
d
e
Item Description Trimble part number
c FmX integrated display 93100-01
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
c
i g
f
h d
e
Item Description Trimble part number
c FmX integrated display 93100-02
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
h NMO to TNC 20 ft antenna cable and base 62120
i 900 MHz radio antenna kit 22882-10
In this chapter:
FmX / EZ-Steer / WAAS / EGNOS corrections This chapter describes how to connect the FmX
using the power bus integrated display to the Trimble® EZ-Steer®
assisted steering system.
FmX / EZ-Steer / WAAS / EGNOS corrections
with external power leads
c
g
f j
d k
h
e i
Note – The EZ-Steer assisted steering system must be powered separately to power the motor.
Note – To use the EZ-Guide 500 lightbar cable (P/N 62974) and instructions on how to repin the cable,
see the support bulletin FmX - Modifying EZ-Steer Cable P/N 62974 For Use With FmX.
c
g
f j
h k
d
e
i
Note – The EZ-Steer assisted steering system must be powered separately to power the motor.
Note – To use the EZ-Guide 500 lightbar cable (P/N 62974) and instructions on how to repin the cable,
see the support bulletin FmX - Modifying EZ-Steer Cable P/N 62974 For Use With FmX
In this chapter:
FmX / Autopilot / WAAS/EGNOS corrections FmX / Autopilot / AgGPS 252/262
FmX / Autopilot / OmniSTAR XP/HP FmX / Factory-ready CNH vehicle
corrections
FmX / Autopilot / Factory-ready CNH vehicle
FmX / Autopilot / RTK corrections / external receiver
FmX with external switch / Autopilot / RTK FmX / Autopilot / AGCO Wheeled Tractors
corrections
This chapter shows the different ways to connect
FmX with ignition sensing / Autopilot / RTK the FmX integrated display to the Autopilot™
corrections automated steering system.
FmX / Autopilot / TrueGuide or Implement
Monitoring
FmX / Autopilot / TrueGuide or Implement
Monitoring with an AgGPS 252/262 external
receiver
FmX / Autopilot / TrueTracker / RTK
corrections
C CAUTION – Connecting the Port Replicator on the FmX display to the NavController II cable to
the P4 or P12 connector of the NavController II harness will result in damage to the FmX /
FM-1000 integrated display, and will void the warranty.
c
k
P3 / GPS
connector
i
j
g l
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000™
integrated display, and will void the warranty.
c
k
P3 / GPS
connector
j g l
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
c
m k
P3 / GPS
connector
j
n i
l g
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness n will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
c
m k P3 / GPS
connector
i
j
g p
l
d
o h
n f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
c
m k P3 / GPS
connector
i
j
l g o
d h
n
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness o will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
n
See note
k
c o
k
P3 / GPS
connector
m
i
j
g p
l
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for implements with a long
tongue.
k o
m q
P3 / GPS
c n connector
j p
l i
g r See note B
P2 power
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional 45' 10-pin data extension cable (P/N AG_0793-1290-450) is available for
implements with a long tongue.
Note – Connect to port “A” of the 252/262 receiver only.
Note – Connect to port “A” or “B”.
See note A
q k p
c s r i
k o
m See note B
n P3 / GPS
connector
j
i
g t
l P2 power
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable n to the P4 or
P12 connector of the NavController II harness t will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for implements with a long
tongue.
Note – An optional 45' 10-pin data extension cable (P/N AG_0793-1290-450) is available for
implements with a long tongue
See note B
See note A
k
P3 / GPS
c connector
i
l P2 / Power
g P4
Display
j h
d
f
e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
g c
k
i
f m
l
j
h
d
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable j to the P4
connector of the NavController II harness will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
See note k
c j
h i
g
d f
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable f to the P4
connector of the NavController II harness will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
P3 GPS
f g
h P12 spare
e j
Optional cables
d
P4
Display
i k
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable e to the P4 or
P12 connector of the NavController II harness f will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
In this chapter:
FmX / EZ-Pilot This chapter shows how to connect the FmX
integrated display to the EZ-Pilot™ steering
system.
FmX / EZ-Pilot
This figure shows how to connect the FmX integrated display to the EZ-Pilot system and a remote
engage switch.
e
c
To remote engage
f
See note
l
g h
o
d
n
i
m
j
In this chapter:
FmX / Field-IQ cab kit / Powell hitch FmX / Field-IQ Rate and Section Control to
connector AGCO RoGator (2007 and later)
FmX / Field-IQ cab kit / Powell hitch FmX / Field-IQ cab kit / NH3 and liquid
connector / power relay application full harness
Field-IQ / Rawson Par 2 drives / Tru Count Air FmX / Autopilot / Field-IQ cab kit / Spreader
Clutch
FmX / Field-IQ Cab Kit / Seed Monitoring
FmX / Field-IQ cab kit / Rawson PAR 40 Only
FmX / Autopilot / Field-IQ cab kit / Rawson FmX / Field-IQ Cab Kit / Row Section Control
PAR 40 / RTK Corrections
FmX / Field-IQ cab kit / Seed monitoring /
FmX / Field-IQ Rate and Section control to Row section control
Raven 4x0 or EZ-Boom harness
FmX / Field-IQ cab kit / Seed monitoring /
FmX / Field-IQ Section Control only to the Rate and Section Control
Raven 4x0
FmX / Field-IQ cab kit / Seed monitoring /
FmX / Field-IQ Section Control to Raven 4x00 Rate and Section Control/ Liquid Control
FmX / Field-IQ Rate and Section Control to FmX / Field-IQ Cab Kit / Seed Monitoring /
Raven 4x00 Rawson PAR 2 Seeding
FmX / Field-IQ Rate and Section Control for FmX/Field-IQ Cab Kit / Seed Monitoring /
CaseIH SPX (2009 and later) sprayers Rawson PAR 2 Seeding / Row Section Control
This chapter shows the different ways to connect the FmX integrated display to the Field-IQ™ crop
input control system.
C CAUTION – Connecting the Port Replicator on the FmX display to the NavController II cable to
the P4 or P12 connector of the NavController II harness will result in damage to the FmX /
FM-1000 integrated display, and will void the warranty.
k c To vehicle battery
e f
j
l d
h Optional: Connection
g not required when
relay cable P/N 77533
is not used.
i
To vehicle battery
m To implement
n
e f
l j
d
g
h
i
To vehicle battery
m To implement
o
n
e f
j d
g
i
h
m k
l
n
c f g j
p e h
n r
o i
q
d
k
m l
u s
t
v
w
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable e to the P4 or
P12 connector of the NavController II harness f will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
h c f
e
i g
d
j
k l m
h c f
e
g
i d
j
k l m
h c f
e
g
i d
j
k l m
h c f
e
g
i d
j
k
l m
h c f
e
g
i d
k n
j
k l
m
o
i
g d
To boom switches
To power
e
j k l
n
p
o
To boom sections
To pump
To flowmeter
Diagram
m of
of Field-IQ™
Fiield IQ System,
Sy Full Harness for Sprayers
c
Outside
the cab e
g
f
d
k
h i j
Inside
the cab
l m
Main cab harness replicated on sprayer and spreader
n
o
p
q r s t
c
h
f
g i
e
k
m
Necessary components to l
replicate spreader
c m
e
g
f
d i
j n
h k
c
e
d k
j g
l m
i f
h
n
s
r q
c
e n
g
d j k
u
i l f
h
o
t
s
r
q
c
e n
g
d j k
g
ww
i l f
h
o
v
u p
t
s
r q
c n
e g
d j
k g w
i l f f
h
o
v
t u
s r q p
y x z A
c
h
e o n
d j k g
p
i l
f
q
h r
e n
c g
d j
k g u
i l f f y
h o v
t
x
p w
r s
q
In this chapter:
FmX / GreenSeeker This chapter shows how to connect the FmX
integrated display to the GreenSeeker variable
rate application and mapping system.
FmX / GreenSeeker
This figure shows how to connect the FmX integrated display with the GreenSeeker system, while
using WAAS or EGNOS corrections.
Power switch
g c
k
f
h j
d
e i
GreenSeeker sensor
l l GreenSeeker sensor
m m m m
In this chapter:
Manual guidance FmX / EZ-Boom This chapter shows the different ways to
connect the FmX integrated display to the EZ-
FmX / Autopilot / EZ-Boom / RTK corrections
Boom® automated application control system.
FmX / Autopilot / EZ-Boom / TrueTracker /
RTK corrections
C CAUTION – Connecting the Port
Replicator on the FmX display to the
FmX / EZ-Boom / EZ-Steer / RTK corrections /
power bus NavController II cable to the P4 or P12
connector of the NavController II harness
FmX / EZ-Boom / EZ-Steer / RTK corrections / will result in damage to the FmX /
external power leads FM-1000 integrated display, and will void
the warranty.
k
g c
i
j
f
h
d
e
Item Description Trimble part number
c FmX integrated display 93100-01
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
h FmX to CAN cable with port replicator 75407
i EZ-Boom 2010 to FMD and EZ-Guide 500 cable 61437
j CAN terminator 59783
k EZ-Boom controller 59898-00
o q
m k
p
c n
P3 / GPS
connector
j
l g r i
d h
f
e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness r will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
q See note
k p
c w r i
k o
m
n P3 / GPS
connector
j
g x i
l
d h
f e
t v
u
s
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness x will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for implements with a long
tongue.
n
l
h
j m
c k p
g r
i q
d o
f e
c
g
i
o
f q
n
h p
d
e r
m
k
l
j
Item Description Trimble part number
c FmX integrated display 93100-02
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
h NMO to TNC 20 ft antenna cable and base 62120
i 900 MHz radio antenna kit 22882-10
j FmX to CAN cable with port replicator 75407
k EZ-Boom 2010 to FMD and EZ-Guide 500 cable 61437
l CAN terminator 59783
In this chapter:
FmX / Autopilot / radar output / serial This chapter shows the different ways to
variable rate for Raven SCS400 or SCS600 connect the FmX integrated display to
equipment from third-party equipment for
FmX / Autopilot / radar output / serial
radar output and serial control.
variable rate for Rawson
FmX / Autopilot / radar output / serial
variable rate C CAUTION – Connecting the Port
Replicator on the FmX display to the
FmX / Autopilot / serial connection for Hardi NavController II cable to the P4 or P12
5500 controller connector of the NavController II harness
will result in damage to the FmX /
FM-1000 integrated display, and will void
the warranty.
p m
n c
P3/GPS
connector
i
o
k
g l
j d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
p m
n c
P3/GPS
connector
k i
o
l
g
j
d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
o m
p n c
See note A
k P3/GPS
See note B connector
i
j
g l
d
h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
c
m
P3/GPS
connector
n l j
h i
k
d g
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable h to the P4 or
P12 connector of the NavController II harness i will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – For the Hardi 5500 controller to work with the FmX integrated display, it must have firmware
version 3.16 or greater installed and have a JOBCOM control box connected.
In this chapter:
Manual guidance FmX / Tru Application This chapter shows the different ways to
Control connect the FmX integrated display to the Tru
Application Control™ system.
FmX / Autopilot / Tru Application Control /
RTK corrections
FmX / Autopilot / Tru Application Control / C CAUTION – Connecting the Port
Replicator on the FmX display to the
TrueTracker / RTK corrections NavController II cable to the P4 or P12
connector of the NavController II harness
will result in damage to the FmX /
FM-1000 integrated display, and will void
the warranty.
i g c
k
f
h j
d
e
Item Description Trimble part number
c FmX integrated display 93100-02
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
h NMO to TNC 20ft antenna cable and base 62120
i 900 MHz radio antenna kit 22882-10
j FmX to CAN cable with port replicator 75407
k Application Control cab harness cable 64909
o
m k
n
c P3 / GPS
connector
j
g p i
l
d
h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
q See note
k
c p
u r i
k
o
m n P3 / GPS
connector
j
g v i
l
d h
f e
t
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness v will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for implements with a long
tongue.
In this chapter:
FmX / Autopilot / AgGPS 252/262 This chapter shows the different ways to
connect the FmX integrated display to external
FmX / TrueGuide or Implement Monitoring
receivers.
with an AgGPS 252/262 external receiver
FmX / Autopilot / External receiver for
Implement Monitoring, TrueGuide, or C CAUTION – Connecting the Port
Replicator on the FmX display to the
FieldLevel II NavController II cable to the P4 or P12
FmX / Autopilot / Ag3000 VRS corrections connector of the NavController II harness
will result in damage to the FmX /
FmX / Autopilot / Sierra wireless modem FM-1000 integrated display, and will void
FmX / Autopilot / DCM-300 the warranty.
See note B
See note A
k
P3 / GPS
c connector
i
l P2 / Power
g P4
Display
j h
d
f
e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
f e
CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
C P12 connector of the NavController II harness r will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional 45' 10-pin data extension cable (P/N AG_0793-1290-450) is available for
implements with a long tongue.
Note – Connect to port “A” only.
Note – Connect to port “A” or port “B”.
r See note A
t
See note B
k AUDIO
ETHERNET
o
s
REVERSE
POLARITY
REMOVE
VENT: DO NOT
n
m
c
m
j
g p i l
l P3 / GPS
d connector
h q
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for implements with a long
tongue.
Note – The receiver adaptor cable q must be connected to either port “A” or port “B”.
o
m n
c
k
P3 / GPSconnector
j
i
g l
d
h
f e
Note: TruTracker not available with this configuration
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness l will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
k c
j i
g
d l
m h
f
e
C CAUTION – Connecting the Port Replicator on the FmX / FM-1000 display to NavController II
cable g to the P4 or P12 connector of the NavController II harness l will result in damage to
the display and will void the warranty.
c
k
n P3/GPS connector
o i
r j
p g
m
d l
q
h
f
e
C CAUTION – Connecting the Port Replicator on the FmX / FM-1000 to NavController II cable g
to the P4 or P12 connector of the NavController II harness l will result in damage to the
display and will void the warranty.
In this chapter:
FmX / AgLeader YM2000 yield monitoring This chapter shows the different ways to
system connect the FmX integrated display to a Yield
Monitoring system.
FmX / John Deere 9x60 / 9x70 yield
monitoring system
C CAUTION – Connecting the Port
Replicator on the FmX display to the
NavController II cable to the P4 or P12
connector of the NavController II harness
will result in damage to the FmX /
FM-1000 integrated display, and will void
the warranty.
c
h
f
d
e
Item Description Trimble part number
c FmX integrated display 93100-01
d FmX power cable 66694
e FmX basic power cable 67258
f 8 m GPS TNC/TNC RT angle cable 50449
g Ag25 GNSS antenna 77038-00
h Display to DE9 RS232 cable 67091
g
i
c
f h
e
Note – Connect only to port A on the FmX integrated display; when using yield monitoring do not
connect another CAN device to the occupied port.
In this chapter:
FmX / Water Management cabling This chapter shows how to connect the FmX
integrated display to the WM-Drain™ solution.
FmX / WM-Drain / IMD-600
g h j
t
i
f
l c
d e
k
m o
n
s
+ p q
–
r
In this chapter:
FmX / Autopilot / FieldLevel II / AGCO FmX / Autopilot / AgGPS 252/262 /
Challenger MT / RTK corrections FieldLevel II / Tandem or dual antenna / RTK
corrections
FmX / Autopilot / FieldLevel II / CNH direct
connect / RTK corrections FmX / FieldLevel II / Without power bus
FmX / Autopilot / FieldLevel II / John Deere This chapter shows the different ways to connect
direct-connect / RTK corrections the FmX integrated display to the FieldLevel II
system.
FmX / Autopilot / FieldLevel II / Proportional
valve / RTK corrections
FmX / Autopilot / FieldLevel II / PT valve /
RTK corrections
FmX / FieldLevel II / Tandem or dual antenna
/ RTK corrections
C CAUTION – Connecting the Port Replicator on the FmX display to the NavController II cable to
the P4 or P12 connector of the NavController II harness will result in damage to the FmX /
FM-1000 integrated display, and will void the warranty.
n k
c o
k P3 / GPS
connector
s
Tractor
m i
cabling
j t r
g u
l P2 power P12 spare
d h v
f e
q
Tractor cabling
CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
C P12 connector of the NavController II harness t will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
n k
c
k P3 / GPS
o
connector v
m
i
j
g w
l
d
h
f u
e s
q t
r
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness w will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
n k
c o
k P3 / GPS
connector
w
m
i
j
g x
l v
d
h
f e s
q t u
r
p
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness x will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
n k
c o
k P3 / GPS
connector
w
m i
j
g x
l v
d h
h
f e
q s t u
r
p
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness x will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
n k
k c P3 / GPS
o
connector
m w
i
j
g x
l v
d h
f h
e
q s t u
r
p
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness x will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
j
m d j
Item 3
f eoptional
Connect to direct-connect
cable or valve module
g
Note – An optional LMR400 65' extension cable (P/N 67473) is available for tandem buckets.
See note
h l
h l i
m i
k k
s
r
c P3 GPS
u p
q j
j
t n
P4
Display
d o
f e
Connect to direct-connect
cable or valve module
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable m to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – An optional LMR400 65' extension cable (P/N 67473) is available for tandem buckets.
h v w
o u To proportional valve
k i q
g y To CNH
d p x direct-connect
q
e
A B
p z
To JD direct-connect
q
To AGCO Challenger MT
C
f
In this chapter:
FmX / ISOBus This chapter shows how to connect the FmX
integrated display to an ISOBus system.
FmX / ISOBus
This figure shows how to connect the FmX integrated display an ISOBus system:
CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
C P12 connector of the NavController II harness t will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
In this chapter:
FmX / 4 AgCam cameras / Autopilot / RTK This chapter shows the different accessories,
corrections including lightbars and cameras, that can be
added to the FmX integrated display.
FmX / Autopilot / EZ-Boom / Display-
mounted LB25 external lightbar (option 1)
FmX / Autopilot / EZ-Boom / Remote- C CAUTION – Connecting the Port
Replicator on the FmX display to the
mounted LB25 external lightbar (option 2) NavController II cable to the P4 or P12
FmX / Autopilot / EZ-Boom / multiple LB25 connector of the NavController II harness
external lightbars / RTK corrections will result in damage to the FmX /
FM-1000 integrated display, and will void
FmX / EZ-Remote joystick the warranty.
o c o
m k
n
n
P3 / GPS connector
j
g p i
l
d
h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness p will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
o q
m k p
c n P3 / GPS
connector
j
l r i
g
s
t d h
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness r will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – When using the LB25 external lightbar, no other CAN device may be used on the port.
Note – When using the LB25 external lightbar and cable P/N 72420, use only port B with internal
termination.
o q
m k p
c n
P3 / GPS
connector
l j
v g r i
u n d h
t s
f e
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness r will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – When using the LB25 external lightbar, no other CAN device may be used on the port.
Note – When using the LB25 external lightbar and cable P/N 67094, use only port B with internal
termination.
o q
m k p
v c n P3 / GPS
u connector
u j
l
g r i
v s d h
v t
f e
u
u
C CAUTION – Connecting the Port Replicator on the FmX to NavController II cable g to the P4 or
P12 connector of the NavController II harness r will result in damage to the FmX/FM-1000
integrated display, and will void the warranty.
Note – When using the LB25 external lightbars, no other CAN device may be used on the port.
Note – When using the LB25 external lightbar and cable P/N 72420, use only port B with internal
termination.
e
f