Professional Documents
Culture Documents
SECTION
EXTERIOR LIGHTING SYSTEM
EXL B
E
CONTENTS
HALOGEN TYPE HEADLAMP AIMING CONTROL (MANUAL) ...........12 F
HEADLAMP AIMING CONTROL (MANUAL) :
PRECAUTION ............................................... 5 System Description ..................................................12
G
PRECAUTIONS ................................................... 5 FRONT FOG LAMP SYSTEM ...................................12
Precaution for Supplemental Restraint System FRONT FOG LAMP SYSTEM : System Diagram....13
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- FRONT FOG LAMP SYSTEM : System Descrip-
SIONER" ................................................................... 5 tion ...........................................................................13 H
Precaution Necessary for Steering Wheel Rota- FRONT FOG LAMP SYSTEM : Fail-Safe ...............13
tion after Battery Disconnect ..................................... 5
REAR FOG LAMP SYSTEM ......................................13
I
SYSTEM DESCRIPTION .............................. 7 REAR FOG LAMP SYSTEM : System Diagram ......14
REAR FOG LAMP SYSTEM : System Description....14
COMPONENT PARTS ........................................ 7
Component Parts Location ........................................ 7 TURN SIGNAL AND HAZARD WARNING LAMP J
Component Description ............................................ 8 SYSTEM .....................................................................14
Light & Rain Sensor .................................................. 8 TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram ....................................14
K
SYSTEM .............................................................. 9 TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description ................................14
HEADLAMP SYSTEM ................................................. 9
HEADLAMP SYSTEM : System Diagram ................. 9 PARKING, LICENSE PLATE AND TAIL LAMP EXL
HEADLAMP SYSTEM : System Description ............. 9 SYSTEM (WITHOUT DTRL) ......................................15
HEADLAMP SYSTEM : Fail-Safe ........................... 10 PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM (WITHOUT DTRL) : System Diagram ......15 M
AUTO LIGHT SYSTEM (WITHOUT DTRL) ............... 10 PARKING, LICENSE PLATE AND TAIL LAMP
AUTO LIGHT SYSTEM (WITHOUT DTRL) : Sys- SYSTEM (WITHOUT DTRL) : System Description
tem Diagram ............................................................ 10 ....15
AUTO LIGHT SYSTEM (WITHOUT DTRL) : Sys- PARKING, LICENSE PLATE AND TAIL LAMP N
tem Description ....................................................... 10 SYSTEM (WITHOUT DTRL) : Fail-Safe ..................16
AUTO LIGHT SYSTEM (WITH DTRL) ...................... 11 PARKING, LICENSE PLATE AND TAIL LAMP
AUTO LIGHT SYSTEM (WITH DTRL) : System O
SYSTEM (WITH DTRL) ..............................................16
Diagram ................................................................... 11 PARKING, LICENSE PLATE AND TAIL LAMP
AUTO LIGHT SYSTEM (WITH DTRL) : System SYSTEM (WITH DTRL) : System Diagram .............16
Description .............................................................. 11 PARKING, LICENSE PLATE AND TAIL LAMP P
SYSTEM (WITH DTRL) : System Description .........16
DAYTIME RUNNING LIGHT SYSTEM ...................... 12
DAYTIME RUNNING LIGHT SYSTEM : System PARKING, LICENSE PLATE AND TAIL LAMP
Diagram ................................................................... 12 SYSTEM (WITH DTRL) : Fail-Safe .........................17
DAYTIME RUNNING LIGHT SYSTEM : System EXTERIOR LAMP BATTERY SAVER SYSTEM
Description .............................................................. 12 (WITHOUT DTRL) ......................................................17
EXL-1
EXTERIOR LAMP BATTERY SAVER SYSTEM DIAGNOSIS AND REPAIR WORKFLOW ......... 43
(WITHOUT DTRL) : System Diagram ..................... 17 Work Flow ............................................................... 43
EXTERIOR LAMP BATTERY SAVER SYSTEM
(WITHOUT DTRL) : System Description ................ 17 DTC/CIRCUIT DIAGNOSIS ........................ 45
EXTERIOR LAMP BATTERY SAVER SYSTEM HEADLAMP (HI) CIRCUIT ................................ 45
(WITH DTRL) ............................................................. 18 Component Function Check ................................... 45
EXTERIOR LAMP BATTERY SAVER SYSTEM Diagnosis Procedure ............................................... 45
(WITH DTRL) : System Diagram ............................ 18
EXTERIOR LAMP BATTERY SAVER SYSTEM HEADLAMP (LO) CIRCUIT ............................... 47
(WITH DTRL) : System Description ........................ 18 Component Function Check ................................... 47
Diagnosis Procedure ............................................... 47
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) ........................................ 19 HEADLAMP GROUND CIRCUIT ...................... 49
Diagnosis Procedure ............................................... 49
COMMON ITEM ........................................................ 19
COMMON ITEM : CONSULT-III Function (BCM - DAYTIME RUNNING LIGHT RELAY CIRCUIT
COMMON ITEM) .................................................... 19 ... 50
Component Function Check ................................... 50
HEADLAMP .............................................................. 20 Diagnosis Procedure ............................................... 50
HEADLAMP : CONSULT-III Function (BCM - Component Inspection ............................................ 51
HEAD LAMP) .......................................................... 20
HEADLAMP AIMING SYSTEM (MANUAL) ...... 53
FLASHER .................................................................. 22 Component Inspection ............................................ 53
FLASHER : CONSULT-III Function (BCM -
FLASHER) .............................................................. 22 FRONT FOG LAMP CIRCUIT ........................... 54
Component Function Check ................................... 54
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN- Diagnosis Procedure ............................................... 54
TELLIGENT KEY SYSTEM) .............................. 24
REAR FOG LAMP CIRCUIT ............................. 56
COMMON ITEM ........................................................ 24 Component Function Check ................................... 56
COMMON ITEM : CONSULT-III Function (BCM - Diagnosis Procedure ............................................... 56
COMMON ITEM) .................................................... 24
PARKING LAMP CIRCUIT ................................ 58
HEADLAMP .............................................................. 24
HEADLAMP : CONSULT-III Function (BCM - WITHOUT DAYTIME RUNNING LIGHT SYSTEM ... 58
HEAD LAMP) .......................................................... 25 WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Component Function Check ................................. 58
FLASHER .................................................................. 26 WITHOUT DAYTIME RUNNING LIGHT SYSTEM
FLASHER : CONSULT-III Function (BCM - : Diagnosis Procedure ............................................. 58
FLASHER) .............................................................. 26
WITH DAYTIME RUNNING LIGHT SYSTEM ........... 59
DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN- WITH DAYTIME RUNNING LIGHT SYSTEM :
TELLIGENT KEY SYSTEM) .............................. 28 Component Function Check ................................... 59
Diagnosis Description ............................................. 28 WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
CONSULT-III Function (IPDM E/R) ........................ 30 agnosis Procedure .................................................. 60
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT TAIL LAMP CIRCUIT ........................................ 61
INTELLIGENT KEY SYSTEM) .......................... 33
Diagnosis Description ............................................. 33 WITHOUT DAYTIME RUNNING LIGHT SYSTEM ... 61
CONSULT-III Function (IPDM E/R) ........................ 35 WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Component Function Check ................................. 61
ECU DIAGNOSIS INFORMATION .............. 38 WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Diagnosis Procedure ............................................. 61
BCM, IPDM E/R ................................................. 38
List of ECU Reference ............................................ 38 WITH DAYTIME RUNNING LIGHT SYSTEM ........... 62
WITH DAYTIME RUNNING LIGHT SYSTEM :
WIRING DIAGRAM ..................................... 39 Component Function Check ................................... 62
WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
EXTERIOR LIGHTING SYSTEM ....................... 39 agnosis Procedure .................................................. 63
Wiring Diagram ....................................................... 39
LICENSE PLATE LAMP CIRCUIT .................... 65
BASIC INSPECTION ................................... 43
EXL-2
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .... 65 BOTH SIDE FRONT FOG LAMPS ARE NOT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM TURNED ON ..................................................... 82 A
: Component Function Check .................................. 65 Description ...............................................................82
WITHOUT DAYTIME RUNNING LIGHT SYSTEM Diagnosis Procedure ...............................................82
: Diagnosis Procedure ............................................. 65 B
PERIODIC MAINTENANCE ........................ 83
WITH DAYTIME RUNNING LIGHT SYSTEM ............ 65
WITH DAYTIME RUNNING LIGHT SYSTEM : HEADLAMP AIMING ADJUSTMENT ............... 83
Component Function Check .................................... 66 C
WITH DAYTIME RUNNING LIGHT SYSTEM : Di- LHD ............................................................................83
agnosis Procedure .................................................. 66 LHD : Description ....................................................83
LHD : Aiming Adjustment Procedure .......................84
LIGHT & RAIN SENSOR ....................................67 D
Component Function Check .................................... 67 RHD ............................................................................85
Diagnosis Procedure ............................................... 67 RHD : Description ....................................................85
RHD : Aiming Adjustment Procedure ......................86 E
TURN SIGNAL LAMP CIRCUIT .........................69
Component Function Check .................................... 69 FRONT FOG LAMP AIMING ADJUSTMENT ... 88
Diagnosis Procedure ............................................... 69 Description ...............................................................88
Aiming Adjustment Procedure .................................88 F
HAZARD SWITCH ..............................................72
Component Function Check .................................... 72 REMOVAL AND INSTALLATION ............... 89
Diagnosis Procedure ............................................... 72 G
HEADLAMP ...................................................... 89
SYMPTOM DIAGNOSIS .............................. 74 Exploded View .........................................................89
Removal and Installation .........................................89
EXTERIOR LIGHTING SYSTEM SYMPTOMS....74 Replacement ...........................................................90 H
Disassembly and Assembly .....................................90
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .... 74
WITHOUT DAYTIME RUNNING LIGHT SYSTEM FRONT COMBINATION LAMP ........................ 91 I
: Symptom Table ..................................................... 74 Exploded View .........................................................91
Removal and Installation .........................................91
WITH DAYTIME RUNNING LIGHT SYSTEM ............ 75 Replacement ...........................................................92
WITH DAYTIME RUNNING LIGHT SYSTEM : Disassembly and Assembly .....................................92 J
Symptom Table ....................................................... 75
FRONT FOG LAMP .......................................... 93
BOTH SIDE HEADLAMPS (HI) ARE NOT Exploded View .........................................................93 K
TURNED ON .......................................................78 Removal and Installation .........................................93
Description .............................................................. 78 Replacement ...........................................................93
Diagnosis Procedure ............................................... 78
LIGHT & RAIN SENSOR .................................. 95 EXL
BOTH SIDE HEADLAMPS (LO) ARE NOT Exploded View .........................................................95
TURNED ON .......................................................79 Removal and Installation .........................................95
Description .............................................................. 79 M
Diagnosis Procedure ............................................... 79 LIGHTING & TURN SIGNAL SWITCH ............. 96
Removal and Installation .........................................96
PARKING, LICENSE PLATE AND TAIL
LAMPS ARE NOT TURNED ON ........................80 HAZARD SWITCH ............................................ 97 N
Exploded View .........................................................97
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .... 80 Removal and Installation .........................................97
WITHOUT DAYTIME RUNNING LIGHT SYSTEM O
: Description ............................................................ 80 SIDE TURN SIGNAL LAMP .............................. 98
WITHOUT DAYTIME RUNNING LIGHT SYSTEM Exploded View .........................................................98
: Diagnosis Procedure ............................................. 80 Removal and Installation .........................................98
Replacement ...........................................................98 P
WITH DAYTIME RUNNING LIGHT SYSTEM ............ 80
WITH DAYTIME RUNNING LIGHT SYSTEM : De- HEADLAMP AIMING SWITCH ......................... 99
scription ................................................................... 80 Exploded View .........................................................99
WITH DAYTIME RUNNING LIGHT SYSTEM : Di- Removal and Installation .........................................99
agnosis Procedure .................................................. 80
REAR COMBINATION LAMP ......................... 100
Exploded View ....................................................... 100
EXL-3
Removal and Installation .......................................100 REAR FOG LAMP ............................................ 104
Replacement .........................................................101 Exploded View ...................................................... 104
Removal and Installation ....................................... 104
HIGH-MOUNTED STOP LAMP ....................... 102 Replacement ......................................................... 105
Exploded View .......................................................102
Removal and Installation .......................................102 SERVICE DATA AND SPECIFICATIONS
LICENSE PLATE LAMP .................................. 103 (SDS) ......................................................... 106
Exploded View .......................................................103 SERVICE DATA AND SPECIFICATIONS
Removal and Installation .......................................103 (SDS) ................................................................ 106
Replacement .........................................................103
Bulb Specifications ................................................ 106
EXL-4
PRECAUTIONS
< PRECAUTION > [HALOGEN TYPE]
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000006466719
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
D
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the E
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected F
by the passenger air bag deactivation switch.
WARNING: G
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. H
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this I
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by J
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser- K
vice.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
EXL
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly M
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. N
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000006466721
O
NOTE:
• Before removing and installing any control units, first turn the ignition switch to the LOCK position, then dis-
connect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both P
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
EXL-5
PRECAUTIONS
< PRECAUTION > [HALOGEN TYPE]
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
5. When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6. Perform self-diagnosis check of all control units using CONSULT-III.
EXL-6
COMPONENT PARTS
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000006451687
B
JMLIA1395ZZ K
EXL-7
COMPONENT PARTS
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Component Description INFOID:0000000006452117
Part Description
BCM Controls the exterior lighting system.
ECM Transmits engine status signal to BCM. (via CAN communication)
Controls the integrated relay, and supplies voltage to the load according to the request
IPDM E/R
from BCM (via CAN communication).
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
integrated buzzer according to the request from BCM (via CAN communication).
Combination meter
• Turns the tail lamp indicator lamp, high beam indicator lamp, front fog lamp indicator
lamp and rear fog lamp indicator lamp ON according to the request from BCM (via
CAN communication).
Light & rain sensor Refer to EXL-8, "Light & Rain Sensor".
The headlamp levelizer adjusts the headlamp light axis upward and downward with
Head lamp aiming motor
the aiming motor integrated in the headlamp.
Combination switch Refer to BCS-9, "COMBINATION SWITCH READING SYSTEM : System Descrip-
(Lighting & turn signal switch) tion".
Headlamp aiming switch Adjusts height of headlamp aiming.
Door switch Refer to DLK-22, "Component Description".
Hazard switch Inputs the hazard switch signal to BCM.
• The light & rain sensor detects the outside ambient light level, for-
ward light level and sensor conditions.
• Based on ambient light level (day/night detection), forward light
level (tunnel detection) and sensor conditions it judges ON/OFF
condition for exterior lamps.
• And it transmits exterior lamp ON/OFF request to the BCM by the
light & rain sensor serial link.
• BCM controls each function depending on the signals. And it
detects the light & rain sensor serial link error and the light & rain
sensor malfunction.
JSLIA0093ZZ
EXL-8
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
SYSTEM
A
HEADLAMP SYSTEM
HEADLAMP SYSTEM : System Diagram INFOID:0000000006451689
B
F
JPLIA0167GB
G
HEADLAMP SYSTEM : System Description INFOID:0000000006451690
OUTLINE
H
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION I
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
J
Headlamp (LO) ON condition
- Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment)
K
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
EXL
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal. M
EXL-9
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
Follow me home OFF condition
- Ignition switch is turned from OFF→ACC or ON
- Lighting switch is turned from OFF→ON
NOTE:
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during
operation of follow me home function.
• Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass opera-
tion, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approxi-
mately 120 seconds (flash-to-pass operation, 4 times).
• Follow me home function activating time can be set by CONSULT-III. Refer to EXL-20, "HEADLAMP : CON-
SULT-III Function (BCM - HEAD LAMP)"(with Intelligent Key), EXL-25, "HEADLAMP : CONSULT-III Func-
tion (BCM - HEAD LAMP)"(without Intelligent Key).
HEADLAMP SYSTEM : Fail-Safe INFOID:0000000006696679
JMLIA1341GB
OUTLINE
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Auto light function
Control by IPDM E/R
EXL-10
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
- Relay control function
• Auto light function turns the exterior lamps* ON/OFF automatically according to the outside brightness. A
*: Headlamp (LO/HI), parking, license plate and tail lamps (Headlamp HI depends on the combination switch
condition.) license plate lamp
AUTO LIGHT FUNCTION B
• BCM detects the combination switch condition with the combination switch reading function.
• BCM detects the engine condition by the engine status signal received from ECM via CAN communication.
• BCM receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain sensor serial link. C
• BCM judges the ON/OFF status of the exterior lamp according to ON/OFF requests from light & rain sensor
and the vehicle condition.
• BCM transmits each request signal to IPDM E/R via CAN communication according to ON/OFF condition by
the auto light function. D
NOTE:
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT-III. Refer
to EXL-20, "HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)". E
AUTO LIGHT SYSTEM (WITH DTRL)
AUTO LIGHT SYSTEM (WITH DTRL) : System Diagram INFOID:0000000006451834
F
JMLIA1344GB
K
AUTO LIGHT SYSTEM (WITH DTRL) : System Description INFOID:0000000006451835
OUTLINE EXL
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function M
- Headlamp control function
- Auto light function
Control by IPDM E/R N
- Relay control function
• Auto light function turns the exterior lamps* ON/OFF automatically according to the outside brightness.
*: Headlamp (LO/HI), parking lamp, tail lamp (Headlamp HI depends on the combination switch condition.) O
AUTO LIGHT FUNCTION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM detects the engine condition by the engine status signal received from ECM via CAN communication. P
• BCM receives exterior lamp ON/OFF requests from the light & rain sensor by light & rain sensor serial link.
• BCM judges the ON/OFF status of the exterior lamp according to ON/OFF requests from light & rain sensor
and the vehicle condition.
• BCM transmits each request signal to IPDM E/R via CAN communication according to ON/OFF condition by
the auto light function.
NOTE:
EXL-11
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
ON/OFF timing differs based on the sensitivity from the setting. The setting can be set by CONSULT-III. Refer
to EXL-20, "HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)".
DAYTIME RUNNING LIGHT SYSTEM
DAYTIME RUNNING LIGHT SYSTEM : System Diagram INFOID:0000000006451836
JMLIA1396GB
OUTLINE
• Turns the following exterior lamps ON as the daytime running light.
- Headlamp (LO)
- Parking, license plate and tail lamps.
• Daytime running light is controlled by daytime running light control function and combination switch reading
function of BCM, and relay control function of IPDM E/R.
DAYTIME RUNNING LIGHT OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects vehicle condition depending on the following signals.
- Engine status signal (received from ECM via CAN communication)
• BCM transmits the low beam request signal and daytime running light request signal to IPDM E/R via CAN
communication according to the daytime running light ON condition.
Daytime running light ON condition
- Engine running
- Lighting switch OFF
- Auto light switch is ON, front fog lamp switch and rear fog lamp switch are OFF, and auto light judgement is
OFF.
• IPDM E/R turns the integrated headlamp low relay and daytime running light relay ON according to the low
beam request signal and daytime running light request signal. And it turns each lamps ON.
HEADLAMP AIMING CONTROL (MANUAL)
HEADLAMP AIMING CONTROL (MANUAL) : System Description INFOID:0000000006451692
The headlamp levelizer adjusts the headlamp light axis upward and downward with the aiming motor inte-
grated in the front combination lamp.
FRONT FOG LAMP SYSTEM
EXL-12
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
FRONT FOG LAMP SYSTEM : System Diagram INFOID:0000000006460640
E
JPLIA0178GB
OUTLINE
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM, G
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION H
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog lights request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the front fog lamp ON condition.
I
Front fog lamp ON condition
- Front fog lamp switch ON and any of the followings.
• Lighting switch 1ST
• Lighting switch 2ND J
• Lighting switch AUTO and the ignition switch ON
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog lights request signal. K
Combination meter turns the front fog lamp indicator lamp ON according to the front fog lights request signal.
FRONT FOG LAMP SYSTEM : Fail-Safe INFOID:0000000006696680
EXL
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control. M
If No CAN Communication Is Available With BCM
EXL-13
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
REAR FOG LAMP SYSTEM : System Diagram INFOID:0000000006451696
JPLIA0179GB
OUTLINE
Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function
of BCM.
REAR FOG LAMP OPERATION
• BCM detects the condition of the combination switch by the combination switch reading function.
• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.
Rear fog lamp switch is turned from OFF to ON with any of following condition.
- Lighting switch 2ND
- Lighting switch AUTO and the ignition switch ON
- Front fog lamp ON
• BCM transmits the rear fog lamp status signal to the combination meter using CAN communication.
• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal.
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
INFOID:0000000006451698
JPLIA0180GB
OUTLINE
EXL-14
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM. A
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn B
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuit when the hazard switch is ON. BCM blinks the hazard C
warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION D
• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication
while the turn signal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn signal indicator lamp signal. E
EXL
N
JMLIA0687GB
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : System O
Description INFOID:0000000006452107
OUTLINE P
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con-
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the ON/OFF condition of the parking, license plate and tail lamps.
EXL-15
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON
according to the position light request signal.
• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITHOUT DTRL) : Fail-Safe
INFOID:0000000006696681
JMLIA1342GB
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : System De-
scription INFOID:0000000006452110
OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con-
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the ON/OFF condition of the parking, license plate and tail lamps.
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
EXL-16
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON
• IPDM E/R turns the daytime running light relay ON and turns the parking, license plate and tail lamps ON A
according to the position light request signal.
• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM (WITH DTRL) : Fail-Safe B
INFOID:0000000006696742
EXL
JMLIA0968GB
OUTLINE N
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function O
- Headlamp control function
- Exterior lamp battery saver function
P
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (battery saver is activated) when all of following condition.
EXL-17
SYSTEM
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
• Exterior lamps ON
• When any of the following conditions is satisfied.
- Driver side door switch is turned from OFF to ON while ignition switch is OFF.
- Ignition switch is turned from ON to OFF while driver side door switch is ON.
NOTE:
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.
• Lighting switch ON→ OFF → ON
EXTERIOR LAMP BATTERY SAVER SYSTEM (WITH DTRL)
EXTERIOR LAMP BATTERY SAVER SYSTEM (WITH DTRL) : System Diagram
INFOID:0000000006452114
JMLIA1343GB
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp and rear fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (battery saver is activated) when all of following condition.
• Exterior lamps ON
• When any of the following conditions is satisfied.
- Driver side door switch is turned from OFF to ON while ignition switch is OFF.
- Ignition switch is turned from ON to OFF while driver side door switch is ON.
NOTE:
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.
• Engine running
• Lighting switchON→ OFF → ON
EXL-18
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000006696671
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
CAN Diag Support Monitor
tion manual.
E
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed. F
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item I
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × × K
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
EXL
• Automatic A/C
AIR CONDITONER × ×*2
• Manual A/C
• Intelligent Key system
INTELLIGENT KEY × × × M
• Engine start system
Combination switch COMB SW ×
Body control system BCM × N
NVIS - NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK × O
Theft warning alarm THEFT ALM × × ×
— RETAINED PWR*1 × P
Signal buffer system SIGNAL BUFFER × ×
NOTE:
• *1: This item is displayed, but not used.
• *2: For models with automatic A/C, this diagnosis mode is not used.
EXL-19
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000006452198
WORK SUPPORT
EXL-20
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
DATA MONITOR F
Monitor item
Description
[Unit] G
PUSH SW
The switch status input from push-button ignition switch
[On/Off]
ENGINE STATE H
The engine status received from ECM via CAN communication
[Stop/Stall/Crank/Run]
VEH SPEED 1 The value of the vehicle speed received from combination meter via CAN communi-
[km/h] cation I
TURN SIGNAL R
[On/Off]
TURN SIGNAL L J
[On/Off]
TAIL LAMP SW
[On/Off] K
HI BEAM SW
[On/Off]
HEAD LAMP SW1 EXL
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off]
M
PASSING SW
[On/Off]
AUTO LIGHT SW* N
[On/Off]
FR FOG SW
[On/Off]
O
RR FOG SW
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side) P
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
EXL-21
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Monitor item
Description
[Unit]
DOOR SW-BK
The switch status input from back door switch
[On/Off]
OPTICAL SENSOR*
The sensor condition received from light & rain sensor
[On/Off/NG]
OPTI SEN (DTCT)
[V] NOTE:
OPTI SEN (FILT) The item is indicated, but not monitored
[V]
*: For models without auto light system, this is not displayed.
ACTIVE TEST
WORK SUPPORT
DATA MONITOR
EXL-22
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Monitor item A
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
B
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW C
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function D
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch E
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
F
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC NOTE:
[On/Off] The item is indicated, but not monitored G
ACTIVE TEST
H
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. I
Off Stops the voltage to turn the turn signal lamps OFF.
EXL
EXL-23
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000006696674
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
• Automatic A/C
• Manual A/C AIR CONDITONER × ×*2
• Manual heater
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
— RETAINED PWR*1 × ×
Signal buffer system SIGNAL BUFFER × ×
— PANIC ALARM*1 ×
EXL-24
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP) INFOID:0000000006466728
A
WORK SUPPORT
Monitor item
Description H
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
ACC SW
I
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication J
HI BEAM SW
[On/Off]
HEAD LAMP SW1 K
[On/Off]
HEAD LAMP SW2
[On/Off] EXL
PASSING SW
[On/Off] Each switch status that BCM judges from the combination switch reading function
FR FOG SW*1 M
[On/Off]
EXL-25
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Monitor item
Description
[Unit]
TURN SIGNAL R
[On/Off]
TURN SIGNAL L
Each switch status that BCM judges from the combination switch reading function
[On/Off]
TAIL LAMP SW
[On/Off]
KEY ON SW
The switch status input from key on switch
[On/Off]
KEYLESS LOCK Lock signal status received from remote keyless entry receiver (integrated in the
[On/Off] BCM)
PKB SW The parking brake switch status received from combination meter with CAN commu-
[On/Off] nication
ENGINE RUN
The engine status received from ECM with CAN communication
[On/Off]
LIG SEN COND
The sensor condition received from light & rain sensor
[On/Off/NG]
ACTIVE TEST
*1: For models without front fog lamp, this item is displayed but active test is not operated.
2
* : For models without daytime running light system, this item is not displayed.
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER) INFOID:0000000006451709
DATA MONITOR
EXL-26
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Monitor item A
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
B
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L C
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
D
ACTIVE TEST
EXL
EXL-27
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
Diagnosis Description INFOID:0000000006696675
Operation
Inspection location Operation
sequence
Blinks continuously during operation of auto active test
NOTE:
1 Oil pressure warning lamp
Except for K9K engine models, turn ON continuously during operation of auto active
test.
2 Rear window defogger 10 seconds
3 Front wiper motor LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
4 10 seconds
• Tail lamp
• Front fog lamp
5 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
EXL-28
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Operation
Inspection location Operation
sequence A
6 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
• LO for 5 seconds → HI for 5 seconds (Except for MR16DDT models)
7 Cooling fan B
• 50% duty for 5 seconds → 100% duty for 5 seconds (For MR16DDT models)
JMMIA0564GB
H
*: Only for models with MR16DDT engine
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully. I
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
J
Symptom Inspection contents Possible cause
YES BCM signal input circuit
K
• Rear window defogger
Perform auto active test. • Rear window defogger ground
Rear window defogger does not operate Does the rear window defog- circuit
ger operate? NO • Harness or connector between EXL
IPDM E/R and rear window de-
fogger
• IPDM E/R
Any of the following components do not operate YES BCM signal input circuit
M
• Parking lamp
• License plate lamp Perform auto active test. • Lamp or motor
• Tail lamp Does the applicable system • Lamp or motor ground circuit
NO • Harness or connector between N
• Front fog lamp operate?
• Headlamp (HI, LO) IPDM E/R and applicable system
• Front wiper motor • IPDM E/R
EXL-29
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Symptom Inspection contents Possible cause
• Harness or connector between
IPDM E/R and oil pressure
YES switch
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate
Does the oil pressure warning • CAN communication signal be-
(only for K9K engine models)
lamp blink? tween IPDM E/R and BCM
• CAN communication signal be-
NO
tween BCM and combination
meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
• Harness or connector between
IPDM E/R and cooling fan motor
• Harness or connector between
IPDM E/R and cooling fan con-
trol module.
(Only for models with MR16DDT
Perform auto active test. engine)
Cooling fan does not operate
Does the cooling fan operate? • Harness or connector between
NO cooling fan control module and
cooling fan motor
(Only for models with MR16DDT
engine)
• Cooling fan motor
• Cooling fan control module
(Only for models with MR16DDT
engine)
• IPDM E/R
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.
EXL-30
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
EXL-31
DIAGNOSIS SYSTEM (IPDM E/R) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Monitor Item MAIN
Description
[Unit] SIGNALS
HL WASHER REQ Displays the status of the headlamp washer request signal received from BCM via
[Off/On] CAN communication.
THFT HRN REQ Displays the status of the theft warning horn request signal received from BCM via
[Off/On] CAN communication.
HORN CHIRP NOTE:
[Off/On] The item is indicated, but not monitored.
ACTIVE TEST
Test item
MOTOR FAN Transmits 100% pulse duty signal (PWM signal) to the cooling fan control
4
module.
1 OFF
Except for MR16DDT 2 Operates the cooling fan relay (LO operation).
engine 3
Operates the cooling fan relay (HI operation).
4
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1
Hi
second intervals.
Fog Operates the front fog lamp relay.
EXL-32
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYS-
A
TEM)
Diagnosis Description INFOID:0000000006696677
B
AUTO ACTIVE TEST
Description C
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp (only for K9K engine models)
• Rear window defogger
• Front wiper motor D
• Parking lamp
• License plate lamp
• Tail lamp E
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan F
Operation Procedure
CAUTION:
G
Wiper arm interferes with food when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented. H
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF. I
CAUTION:
Close passenger door.
3. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test J
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
K
4. Oil pressure warning lamp starts blinking when the auto active test starts*. (only for K9K engine models)
*: Except for K9K engine models, oil pressure warning lamp turn ON when auto active test start.
5. After a series of the following operations is repeated 3 times, auto active test is completed. EXL
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to DLK-397,
"Component Function Check" (with super lock) or DLK-522, "Component Function Check" (without super M
lock).
Inspection in Auto Active Test Mode
N
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
Inspection location Operation
sequence O
Blinks continuously during operation of auto active test
NOTE:
1 Oil pressure warning lamp
Except for K9K engine models, turn ON continuously during operation of auto active P
test.
2 Rear window defogger 10 seconds
3 Front wiper motor LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
4 10 seconds
• Tail lamp
• Front fog lamp
EXL-33
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Operation
Inspection location Operation
sequence
5 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
6 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
• LO for 5 seconds → HI for 5 seconds (Except for MR16DDT models)
7 Cooling fan
• 50% duty for 5 seconds → 100% duty for 5 seconds (For MR16DDT models)
JMMIA0564GB
EXL-34
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Symptom Inspection contents Possible cause
A
• Harness or connector between
IPDM E/R and oil pressure
YES switch
• Oil pressure switch B
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate
Does the oil pressure warning • CAN communication signal be-
(only for K9K engine models)
lamp blink? tween IPDM E/R and BCM
• CAN communication signal be-
C
NO
tween BCM and combination
meter
• Combination meter D
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R
E
• Harness or connector between
IPDM E/R and cooling fan motor
• Harness or connector between
IPDM E/R and cooling fan con- F
trol module.
(Only for model with MR16DDT
Perform auto active test. engine)
Cooling fan does not operate
Does the cooling fan operate? • Harness or connector between G
NO cooling fan control module and
cooling fan motor
(Only for model with MR16DDT
H
engine)
• Cooling fan motor
• Cooling fan control module
(Only for model with MR16DDT I
engine)
• IPDM E/R
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R. K
EXL-35
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
ACTIVE TEST
Test item
EXL-36
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION > [HALOGEN TYPE]
Test item Operation Description
A
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay. B
1 OFF
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control
2
module. C
For MR16DDT engine Transmits 75% pulse duty signal (PWM signal) to the cooling fan control
3
module.
MOTOR FAN Transmits 100% pulse duty signal (PWM signal) to the cooling fan control D
4
module.
1 OFF
Except for MR16DDT 2 Operates the cooling fan relay (LO operation). E
engine 3
Operates the cooling fan relay (HI operation).
4
F
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF
TAIL Operates the tail lamp relay. G
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1
Hi H
second intervals.
Fog Operates the front fog lamp relay.
EXL
EXL-37
BCM, IPDM E/R
< ECU DIAGNOSIS INFORMATION > [HALOGEN TYPE]
ECU Reference
BCS-41, "Reference Value"
BCS-64, "Fail-safe"
BCM
BCS-66, "DTC Inspection Priority Chart"
BCS-67, "DTC Index"
PCS-17, "Reference Value"
IPDM E/R PCS-24, "Fail-Safe"
PCS-25, "DTC Index"
ECU Reference
BCS-125, "Reference Value"
BCS-140, "Fail-safe"
BCM
BCS-140, "DTC Inspection Priority Chart"
BCS-141, "DTC Index"
PCS-48, "Reference Value"
IPDM E/R PCS-54, "Fail-Safe"
PCS-55, "DTC Index"
EXL-38
EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [HALOGEN TYPE]
WIRING DIAGRAM A
EXTERIOR LIGHTING SYSTEM
Wiring Diagram INFOID:0000000006707027
B
For connector terminal arrangemants, harness layouts, and alphabets in a (option abbreviation: if not
described in wiring diagram), refer to GI-12, "Connector Information/Explanation of Option Abbreviation".
C
EXL
JCLWA4237GB
EXL-39
EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [HALOGEN TYPE]
JCLWA4238GB
EXL-40
EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [HALOGEN TYPE]
EXL
JCLWA4239GB
EXL-41
EXTERIOR LIGHTING SYSTEM
< WIRING DIAGRAM > [HALOGEN TYPE]
JCLWA4240GB
EXL-42
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [HALOGEN TYPE]
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000006451716
B
OVERALL SEQUENCE
C
EXL
P
JPLIA0313GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
EXL-43
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [HALOGEN TYPE]
>> GO TO 2.
2.SYMPTOM CHECK
Check the symptom from the customer's information.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT-III
Perform the self-diagnosis with CONSULT-III. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT-III)
Perform the self-diagnosis with CONSULT-III. Check that any DTC is not detected. Erase DTC if DTC is
detected before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
EXL-44
HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
DTC/CIRCUIT DIAGNOSIS A
HEADLAMP (HI) CIRCUIT
Component Function Check INFOID:0000000006451718
B
(+) J
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
K
RH Hi Battery voltage
49
Off 0V
E15 Ground EXTERNAL LAMPS
LH Hi Battery voltage EXL
50
Off 0V
Is the inspection result normal?
M
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT N
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector. O
IPDM E/R Headlamp
Continuity
Connector Terminal Connector Terminal
P
RH 49 E45
E15 1 Existed
LH 50 E26
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
EXL-45
HEADLAMP (HI) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
IPDM E/R
Continuity
Connector Terminal
Ground
RH 49
E15 Not existed
LH 50
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
EXL-46
HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
HEADLAMP (LO) CIRCUIT
A
Component Function Check INFOID:0000000006451720
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF D
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
E
NO >> Refer to EXL-47, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006451721
F
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Turn ignition switch OFF. G
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item. H
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.
(+)
(−) Voltage I
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage J
RH 52
Off 0V
E15 Ground EXTERNAL LAMPS
Lo Battery voltage
LH 51 K
Off 0V
Is the inspection result normal?
YES >> GO TO 2. EXL
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF. M
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.
N
IPDM E/R Headlamp
Continuity
Connector Terminal Connector Terminal
RH 52 E45 O
E15 3 Existed
LH 51 E26
Is the inspection result normal?
P
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (LO) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
EXL-47
HEADLAMP (LO) CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
IPDM E/R
Continuity
Connector Terminal
Ground
RH 52
E15 Not existed
LH 51
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
EXL-48
HEADLAMP GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
HEADLAMP GROUND CIRCUIT
A
Diagnosis Procedure INFOID:0000000006451722
Headlamp
Continuity
Connector Terminal D
Ground
RH E45
2 Existed
LH E26
E
Is the inspection result normal?
YES >> Headlamp ground circuit is normal.
NO >> Repair or replace harness.
F
EXL
EXL-49
DAYTIME RUNNING LIGHT RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
DAYTIME RUNNING LIGHT RELAY CIRCUIT
Component Function Check INFOID:0000000006452120
(+)
Voltage
Daytime running light relay (−)
(Approx.)
Connector Terminal
1
E82 3 Ground Battery voltage
6
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK DAYTIME RUNNING LIGHT RELAY
Check daytime running light relay. Refer to EXL-51, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
EXL-50
DAYTIME RUNNING LIGHT RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
NO >> Replace daytime running light relay.
4.CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OUTPUT A
EXTERNAL TAIL 0V
E13 28 Ground
LAMPS Off Battery voltage E
Is the inspection result normal?
YES >> Daytime running light relay circuit is OK.
Fixed at 0 V >>GO TO 5. F
Fixed at battery voltage >>Replace IPDM E/R.
5.CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OPEN CIRCUIT
G
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect IPDM E/R harness connector.
4. Check continuity between IPDM E/R harness connector and daytime running light relay harness connec- H
tor.
O
1.CHECK DAYTIME RUNNING LIGHT RELAY
1. Turn ignition switch OFF.
2. Remove daytime running light relay. P
3. Apply battery voltage to daytime running light relay between terminals 1 and 2.
4. Check continuity of daytime running light relay.
EXL-51
DAYTIME RUNNING LIGHT RELAY CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
EXL-52
HEADLAMP AIMING SYSTEM (MANUAL)
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
HEADLAMP AIMING SYSTEM (MANUAL)
A
Component Inspection INFOID:0000000006451723
F
Is the inspection result normal?
YES >> Headlamp aiming switch is normal.
NO >> Replace the headlamp aiming switch.
G
EXL
EXL-53
FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
FRONT FOG LAMP CIRCUIT
Component Function Check INFOID:0000000006452123
IPDM E/R
Continuity
Connector Terminal
Ground
RH 19
E12 Not existed
LH 20
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect front fog lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check the voltage between IPDM E/R harness connector and ground.
EXL-54
FRONT FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
(+) A
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
Fog Battery voltage
B
RH 19
EXTERNAL Off 0V
E12 Ground
LAMPS Fog Battery voltage
LH 20 C
Off 0V
Is the inspection result normal?
YES >> GO TO 5. D
NO >> Replace IPDM E/R.
5.CHECK FRONT FOG LAMP OPEN CIRCUIT E
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
F
IPDM E/R Front fog lamp
Continuity
Connector Terminal Connector Terminal
G
RH 19 E48
E12 1 Existed
LH 20 E30
Is the inspection result normal? H
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT I
Check continuity between front fog lamp harness connector and ground.
J
Front fog lamp
Continuity
Connector Terminal
Ground
RH E48 K
2 Existed
LH E30
Is the inspection result normal?
YES >> Refer to GI-42, "Intermittent Incident". EXL
NO >> Repair or replace harness.
EXL-55
REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
REAR FOG LAMP CIRCUIT
Component Function Check INFOID:0000000006451728
(+)
Voltage
Rear fog lamp (−) Test item
(Approx.)
Connector Terminal
On 12 V
B85 1 Ground RR FOG LAMP
Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK REAR FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear fog lamp harness connector.
B9*1 51*1
B85 1 Existed
B10*2 52*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 4.
EXL-56
REAR FOG LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
NO >> Repair or replace harness.
4.CHECK REAR FOG LAMP SHORT CIRCUIT A
Check continuity between rear fog lamp harness connector and ground.
EXL
EXL-57
PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
PARKING LAMP CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452125
IPDM E/R
Continuity
Connector Terminal
Ground
37
E14 Not existed
38
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO >> Repair or replace harness. And then replace the fuse.
3.CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect parking lamp connector.
EXL-58
PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item. A
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.
(+)
B
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
EXL-59
PARKING LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006452128
Parking lamp
Continuity
Connector Terminal
Ground
RH E43
2 Existed
LH E24
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
EXL-60
TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
TAIL LAMP CIRCUIT
A
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452129 B
EXL-61
TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
(+)
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
IPDM E/R
Continuity
Connector Terminal Ground
E14 44 Not existed
Is the inspection result normal?
YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO >> Repair or replace harness. And then replace the fuse.
6.CHECK TAIL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear combination lamp connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
EXL-62
TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
EXL-63
TAIL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
EXL-64
LICENSE PLATE LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
LICENSE PLATE LAMP CIRCUIT
A
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452133 B
EXL-66
LIGHT & RAIN SENSOR
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
LIGHT & RAIN SENSOR
A
Component Function Check INFOID:0000000006452196
Check continuity between light & rain sensor harness connector and ground.
O
Light & rain sensor
Continuity
Connector Terminal Ground
R5 3 Existed P
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK LIGHT & RAIN SENSOR SIGNAL
1. Connect light & rain sensor connector.
2. Turn ignition switch ON.
EXL-67
LIGHT & RAIN SENSOR
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
3. Check signal between BCM harness connector and ground with oscilloscope.
(+)
Signal
BCM (−) Condition
(Reference value)
Connector Terminal
M65*1 14*1
2
Ground Ignition switch ON
M68* 11*2
JPMIA0156GB
Approx. 8.7V
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> Replace light & rain sensor.
NO >> GO TO 5.
5.CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector and light & rain sensor connector.
3. Check continuity between BCM harness connector and light & rain sensor harness connector.
M65*1 14*1
R5 2 Existed
M68*2 11*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR SHORT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal
Ground
M65*1 14*1
Not existed
M68*2 11*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> Refer to BCS-93, "Removal and Installation" (with Intelligent Key), BCS-161, "Removal and Instal-
lation" (without Intelligent Key).
NO >> Repair or replace harness.
EXL-68
TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
A
Component Function Check INFOID:0000000006451732
(+)
BCM (–) Condition
Voltage K
(Approx.)
Connector Terminal
EXL
49*1 LH M
60*2
PKID0926E
N
B9*1 Turn signal OFF 0V
Ground
M69*2 switch
O
48*1 RH
61* 2 P
PKID0926E
OFF 0V
EXL-69
TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.
Front turn signal lamp
BCM Front turn signal lamp
Continuity
Connector Terminal Connector Terminal
48*1
RH E46
B9* 1 61*2
1 Existed
M69*2 49*1
LH E27
60*2
48*1
RH E40
B9*1 61*2
1 Existed
M69*2 49*1
LH E23
60*2
48*1
RH B59
B9* 1 61*2
5 Existed
M69*2 49*1
LH B80
60*2
BCM
Continuity
Connector Terminal
48*1
RH Ground
B9*1 61*2
Not existed
M69*2 49*1
LH
60*2
EXL-70
TURN SIGNAL LAMP CIRCUIT
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
YES >> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to BCS-93, "Removal and Installation" (with Intelligent Key), BCS-161, "Removal and Installation" A
(without Intelligent Key).
NO >> Repair or replace harness.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT B
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.
Front turn signal lamp
C
Front turn signal lamp
Continuity
Connector Terminal
Ground D
RH E46
2 Existed
LH E27
EXL
EXL-71
HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
HAZARD SWITCH
Component Function Check INFOID:0000000006451734
(+)
Hazard switch (−) Voltage (Approx.)
Connector Terminal
M45 2 Ground 12 V
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.
M65*1
M45 2 29 Existed
M68*2
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Hazard switch
Continuity
Connector Terminal Ground
M45 2 Not existed
Is the inspection result normal?
EXL-72
HAZARD SWITCH
< DTC/CIRCUIT DIAGNOSIS > [HALOGEN TYPE]
YES >> Replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key) or BCS-161,
"Removal and Installation" (without Intelligent Key). A
NO >> Repair or replace harness.
4.CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
B
Check continuity between hazard switch harness connector and ground.
Hazard switch
Continuity C
Connector Terminal Ground
M45 1 Existed
Is the inspection result normal? D
YES >> Replace hazard switch.
NO >> Repair or replace harness.
E
EXL
EXL-73
EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table INFOID:0000000006451740
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
EXL-74
EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
Symptom Possible cause Inspection item
A
• Parking lamp, tail lamp and license plate lamp
Symptom diagnosis
are not turned ON.
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
• Parking lamp, tail lamp and license plate lamp
Refer to EXL-80, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Di-
are not turned OFF. B
agnosis Procedure".
(Each illumination is turned ON/OFF.)
Indicator lamp is nor-
mal. • Harness between BCM and each Turn signal lamp circuit
(Applicable side per- turn signal lamp Refer to EXL-69, "Component
C
forms the high flasher • Turn signal lamp bulb Function Check".
Turn signal lamp does activation.)
not blink.
• Combination switch D
Indicator lamp is in- • Harness between combination Combination switch
cluded. switch and BCM Refer to BCS-92, "Symptom Table".
• BCM
E
One side Combination meter —
• Combination meter
• Turn signal indicator lamp signal
Both sides Data monitor “TURN IND”
Turn signal indicator (Always)
- BCM
• BCM (FLASHER)
F
• Combination meter
lamp does not blink. Active test “FLASHER”
(Turn signal indicator
Both sides
lamp is normal.) Combination meter G
(Only when activating • Combination meter power supply
Power supply and ground circuit
hazard warning lamp and ground circuit
Refer to MWI-51, "COMBINATION
with the ignition switch • Combination meter
METER : Diagnosis Procedure".
OFF.)
H
• Hazard switch
• Hazard warning lamp does not activate. Hazard switch
• Harness between hazard switch
• Hazard warning lamp continues activating. Refer to EXL-72, "Component
and BCM
(Turn signal is normal.) Function Check".
• BCM I
• Harness between BCM and rear
Rear fog lamp circuit
Rear fog lamp indica- fog lamp
Refer to EXL-56, "Component
tor lamp is normal. • Rear fog lamp bulb J
Function Check".
Rear fog lamp is not • BCM
turned ON. • Combination switch
Rear fog lamp indica- • Harness between combination Combination switch
tor lamp is included. switch and BCM Refer to BCS-92, "Symptom Table".
K
• BCM
• Combination meter
• Rear fog lamp status signal EXL
Rear fog lamp indicator lamp is not turn ON. Data monitor “RR FOG IND”
• Combination meter
(Rear fog lamp turns ON) • BCM (HEAD LAMP)
• BCM
Active test “RR FOG LAMP”
N
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
O
EXL-75
EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
EXL-76
EXTERIOR LIGHTING SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
Symptom Possible cause Inspection item
A
• Fuse
• Parking lamp, tail • Harness between IPDM E/R and Daytime running light relay circuit
lamp, lamp and the li- Each illumination is
the daytime running light relay Refer to EXL-50, "Component
cense plate lamp are turned ON/OFF
• Daytime running light relay Function Check". B
not turned ON. • IPDM E/R
• Parking lamp, tail
lamp, lamp and li- Symptom diagnosis
cense plate lamp are Each illumination is “PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
not turned ON/OFF Refer to EXL-80, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
C
not turned OFF.
Procedure".
Indicator lamp is nor-
mal. • Harness between BCM and each Turn signal lamp circuit D
(Applicable side per- turn signal lamp Refer to EXL-69, "Component
forms the high flasher • Turn signal lamp bulb Function Check".
Turn signal lamp does activation.)
not blink. E
• Combination switch
Indicator lamp is in- • Harness between combination Combination switch
cluded. switch and BCM Refer to BCS-92, "Symptom Table".
• BCM F
One side Combination meter —
• Combination meter
• Turn signal indicator lamp signal G
Both sides Data monitor “TURN IND”
- BCM
Turn signal indicator (Always) • BCM (FLASHER)
• Combination meter
lamp does not blink. Active test “FLASHER”
(Turn signal indicator
lamp is normal.)
Both sides
Combination meter
H
(Only when activating • Combination meter power supply
Power supply and ground circuit
hazard warning lamp and ground circuit
Refer to MWI-51, "COMBINATION
with the ignition switch • Combination meter
METER : Diagnosis Procedure".
OFF.) I
• Hazard switch
• Hazard warning lamp does not activate. Hazard switch
• Harness between hazard switch
• Hazard warning lamp continues activating. Refer to EXL-72, "Component
and BCM J
(Turn signal is normal.) Function Check".
• BCM
• Harness between BCM and rear
Rear fog lamp circuit
Rear fog lamp indica- fog lamp
tor lamp is normal. • Rear fog lamp bulb
Refer to EXL-56, "Component K
Function Check".
Rear fog lamp is not • BCM
turned ON. • Combination switch
Rear fog lamp indica- • Harness between combination Combination switch EXL
tor lamp is included. switch and BCM Refer to BCS-92, "Symptom Table".
• BCM
• Combination meter M
• Rear fog lamp status signal
Rear fog lamp indicator lamp is not turn ON. Data monitor “RR FOG IND”
• Combination meter
(Rear fog lamp turns ON) • BCM (HEAD LAMP)
• BCM
Active test “RR FOG LAMP”
N
EXL-77
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description INFOID:0000000006451741
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure INFOID:0000000006451742
EXL-78
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
A
Description INFOID:0000000006451743
EXL
EXL-79
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description INFOID:0000000006451745
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006451746
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure INFOID:0000000006452141
EXL
EXL-81
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
< SYMPTOM DIAGNOSIS > [HALOGEN TYPE]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description INFOID:0000000006451747
1.CHECK FUSE
Check that the following fuse is fusing.
EXL-82
HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
PERIODIC MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
LHD
B
LHD : Description INFOID:0000000006451749
EXL
JMLIA1244ZZ P
EXL-83
HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
JSLIA0030ZZ
EXL-84
HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
JSLIA0031ZZ F
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
G
(lateral) (Vertical)
RHD K
RHD : Description INFOID:0000000006451751
EXL
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been M
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. N
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.) O
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
P
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
EXL-85
HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
JMLIA1244ZZ
EXL-86
HEADLAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so A
that it is within the aiming adjustment area.
Low beam distribution on the screen
B
A. Aiming adjustment area
B. Elbow point
C. Headlamp center
C
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
JSLIA0028ZZ
JSLIA0029ZZ
J
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
(lateral) (Vertical) K
EXL-87
FRONT FOG LAMP AIMING ADJUSTMENT
< PERIODIC MAINTENANCE > [HALOGEN TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
Description INFOID:0000000006451753
A: DOWN
B: UP
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
JMLIA1249ZZ
A : Cutoff line
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp
X : Cutoff line height
JPLIA0008ZZ
EXL-88
HEADLAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
REMOVAL
C
H
JMLIA1234ZZ
EXL
JMLIA1235ZZ
P
1. Back cover 2. Halogen bulb 3. Headlamp housing assembly
4. Retaining spring 5. EPT sealer [2.8 mm (0.110 in)]
: Do not reuse
CAUTION:
EXL-89
HEADLAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
Disconnect the battery negative terminal or the fuse.
REMOVAL
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".
2. Remove headlamp mounting bolts.
3. Pull out the headlamp assembly forward the vehicle, and then disconnect the connector before removing
the headlamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer toEXL-83, "LHD : Description".
Replacement INFOID:0000000006466836
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect headlamp bulb connector.
2. Remove back cover.
3. Remove retaining spring lock, and then remove bulb from the headlamp housing assembly.
Disassembly and Assembly INFOID:0000000006466837
DISASSEMBLY
1. Remove back cover.
2. Remove retaining spring lock, and then remove bulb from the headlamp housing assembly.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
EXL-90
FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
FRONT COMBINATION LAMP
A
Exploded View INFOID:0000000006466838
REMOVAL B
JMLIA1236ZZ
H
1. Front combination lamp
: N·m (kg-m, in-lb)
I
DISASSEMBLY
EXL
JMLIA1237ZZ
O
1. Parking lamp bulb 2. Parking lamp bulb socket 3. Front turn signal lamp bulb socket
4. Front turn signal lamp bulb 5. Front combination lamp housing
P
Removal and Installation INFOID:0000000006466839
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. Remove front bumper fascia. Refer to EXT-13, "Removal and Installation".
EXL-91
FRONT COMBINATION LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
2. Remove front combination lamp mounting bolts and nut.
3. Pull out front combination lamp assembly forward the vehicle, and then disconnect the connector before
removing the headlamp assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
Interference of front combination lamp lens with front fender may cause intrusion of water into front
combination lamp or rusting of fender due to damage of painted surface. Be careful to operate without
allowing parts to interfere with each other.
Replacement INFOID:0000000006466840
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
PARKING LAMP BULB
1. Rotate the parking lamp bulb socket counterclockwise and unlock it.
2. Remove parking lamp bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
2. Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
Disassembly and Assembly INFOID:0000000006466841
DISASSEMBLY
1. Rotate the parking lamp bulb socket counterclockwise and unlock it.
2. Remove parking lamp bulb from the bulb socket.
3. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
4. Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item and then, install in the reverse order of removal.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
EXL-92
FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
FRONT FOG LAMP
A
Exploded View INFOID:0000000006483048
G
JMLIA1240GB
1. Front fog lamp assembly 2. Metal clip 3. Front fog lamp bulb
4. Front fog lamp bracket 5. U nut 6. Front bumper fascia lower
H
: Pawl
J
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL K
1. Remove front fender protector. Keep the service area. Refer to EXT-22, "Removal and Installation".
2. Disconnect front fog lamp harness connector.
3. Remove front fog lamp bracket. EXL
4. Remove front fog lamp mounting bolt, and then remove front fog lamp from front fog lamp bracket.
INSTALLATION
M
Note the following item, and then installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-88, "Description"
N
Replacement INFOID:0000000006483050
CAUTION:
• Disconnect the battery negative terminal or remove the fuse. O
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters awy from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect P
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1. Remove fender protector. Keep the service area. Refer to EXT-22, "Removal and Installation".
EXL-93
FRONT FOG LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
2. Remove front fog lamp bulb connector (1).
3. Rotate the bulb (2) counterclockwise and unlock it.
JPLIA0345ZZ
EXL-94
LIGHT & RAIN SENSOR
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
LIGHT & RAIN SENSOR
A
Exploded View INFOID:0000000006658845
CAUTION: B
When the light & rain sensor is removed from windshield, the light & rain sensor cannot be re-used.
REMOVAL
C
H
JMLIA1389ZZ
1. Light & rain sensor bracket 2. Mirror base 3. Light & rain sensor
I
4. Inside mirror assembly
: Pawl
: Do not reuse J
K
REMOVAL
1. Remove inside mirror assembly. Refer to MIR-41, "Removal and Installation".
2. Disconnect light & rain sensor connector. EXL
3. Disengage both sides of metal spring clips, and remove the light & rain sensor from the windshield.
INSTALLATION
M
Note the following items, and the install in the reverse order of removal.
CAUTION:
• Surface of windshield should be cleaned.
• Never touch gel/adhesive of new part. N
• Lock the metal spring clips and install the light & rain sensor securely.
EXL-95
LIGHTING & TURN SIGNAL SWITCH
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation INFOID:0000000006466844
REMOVAL
Remove light & turn signal switch. Refer to BCS-94, "Removal and Installation".
INSTALLATION
Install in the reverse order of removal.
EXL-96
HAZARD SWITCH
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
HAZARD SWITCH
A
Exploded View INFOID:0000000006466845
JMLIA1246ZZ
REMOVAL
I
1. Remove Audio unit. Refer to AV-38, "Removal and Installation".
2. Disengage fixing pawls, and then remove hazard switch from instrument panel inside to outside.
INSTALLATION J
Install in the reverse order of removal.
EXL
EXL-97
SIDE TURN SIGNAL LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
SIDE TURN SIGNAL LAMP
Exploded View INFOID:0000000006466847
JMLIA1241ZZ
1. Side turn signal lamp bulb 2. Side turn signal lamp housing
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove the side turn signal lamp in numerical order shown in
the figure.
2. Rotate the bulb socket counterclockwise and unlock it.
NOTE:
Support side turn signal lamp harness with tape so that it won't fall
into the front fender.
JMLIA1302ZZ
INSTALLATION
1. Rotate the bulb socket clockwise and lock it.
2. Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side.
Replacement INFOID:0000000006466849
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1. Remove side turn signal lamp. Refer to EXL-98, "Removal and Installation".
2. Remove bulb from the bulb socket.
EXL-98
HEADLAMP AIMING SWITCH
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
HEADLAMP AIMING SWITCH
A
Exploded View INFOID:0000000006466850
JMLIA1442ZZ
REMOVAL
I
1. Remove instrment lower panel (LH/RH). Refer to IP-13, "Removal and Installation".
2. Remove headlamp aiming switch fixing clips, and then remove headlamp aiming switch from instrument
lower panel (LH/RH).
J
INSTALLATION
Install in the reverse order of removal.
K
EXL
EXL-99
REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
REAR COMBINATION LAMP
Exploded View INFOID:0000000006466852
REMOVAL
JMLIA1217GB
DISASSEMBLY
JMLIA1218ZZ
1. Rear combination lamp housing assembly 2. Back-up lamp bulb 3. Harness connector
4. Rear turn signall lamp bulb 5. Stop/tail lamp bulb
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
1. Full open back door.
EXL-100
REAR COMBINATION LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
2. Remove luggage side lower finisher. Refer to INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal
and Installation". A
3. Remove rear combination lamp mounting bolts.
4. Insert a remover tool into the rear combination lamp rear fender to disengage the clips.
5. Pull up rear combination lamp, and then remove rear combination lamp. B
6. Disconnect rear combination lamp connector.
INSTALLATION C
Install in the reverse order of removal.
Replacement INFOID:0000000006466854
D
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
E
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
F
STOP/TAIL LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-100, "Removal and Installation".
2. Rotate stop/tail lamp bulb socket counterclockwise, and then remove stop/tail lamp bulb socket. G
3. Remove stop/tail lamp bulb from stop/tail lamp bulb socket.
REAR TURN SIGNAL LAMP BULB
H
1. Remove rear combination lamp assembly. Refer to EXL-100, "Removal and Installation".
2. Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
I
3. Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
BACK-UP LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-100, "Removal and Installation". J
2. Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3. Remove back-up lamp bulb from back-up lamp bulb socket.
K
EXL
EXL-101
HIGH-MOUNTED STOP LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
HIGH-MOUNTED STOP LAMP
Exploded View INFOID:0000000006466855
JMLIA1220GB
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Remove blind seal from back door inside.
CAUTION:
Be careful not to damage the blind seal, so that it can be reused.
2. Remove high-mounted stop lamp mounting nuts and connector.
3. Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.
INSTALLATION
Note the following item and then, install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
EXL-102
LICENSE PLATE LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
LICENSE PLATE LAMP
A
Exploded View INFOID:0000000006466857
JMLIA1219ZZ
1. License plate lamp housing assembly 2. Blub 3. License plate lamp blub socket G
: Pawl
CAUTION:
Disconnect battery negative terminal or remove the fuse. I
REMOVAL
1. While pressing the license plate lamp to direction right side, pull
it to direction outside and then remove it. J
2. Disconnect license plate lamp connector.
EXL
JPLIA0364ZZ
M
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000006466859
N
CAUTION:
• Disconnect the battery negative terminal or the fuse. O
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one. P
EXL-103
REAR FOG LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
REAR FOG LAMP
Exploded View INFOID:0000000006466759
REMOVAL
JMLIA1398ZZ
DISASSEMBLY
JMLIA1399ZZ
1. Rear fog lamp housing 2. Rear fog lamp bulb 3. Rear fog lamp bulb socket
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1. Insert any appropriate tool into the gap between the rear fog lamp housing. And pull off the rear fog lamp
from the vehicle.
2. Disconnect the rear fog lamp connector.
INSTALLATION
Installation is the reverse order of removal.
EXL-104
REAR FOG LAMP
< REMOVAL AND INSTALLATION > [HALOGEN TYPE]
Replacement INFOID:0000000006482933
A
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REAR FOG LAMP BULB B
1. Remove rear fog lamp.
2. Rotate the bulb socket counterclockwise and unlock it.
C
3. Remove bulb from its socket.
EXL
EXL-105
SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS) [HALOGEN TYPE]
EXL-106