Professional Documents
Culture Documents
SECTION
EXTERIOR LIGHTING SYSTEM
EXL B
E
CONTENTS
TYPE 1 PARKING, LICENSE PLATE AND TAIL LAMP F
SYSTEM .....................................................................16
HOW TO USE THIS MANUAL ...................... 6 PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM : System Description ................................17 G
APPLICATION NOTICE ...................................... 6 PARKING, LICENSE PLATE AND TAIL LAMP
Information ................................................................ 6 SYSTEM : Circuit Diagram ......................................18
PARKING, LICENSE PLATE AND TAIL LAMP
PRECAUTION ............................................... 7 SYSTEM : Fail-safe .................................................18
H
TAIL LAMP RH RELAY CIRCUIT ................... 143 FRONT COMBINATION LAMP ........................ 167
Diagnosis Procedure .............................................143 Exploded View ...................................................... 167
Component Inspection ...........................................144 Removal and Installation ....................................... 167
Replacement ......................................................... 168
HEADLAMP AIMING SYSTEM (MANUAL) .... 145 Disassembly and Assembly .................................. 168
Component Inspection ...........................................145
LIGHTING & TURN SIGNAL SWITCH ............. 169
PARKING LAMP CIRCUIT .............................. 146 Exploded View ...................................................... 169
Component Function Check ..................................146
Diagnosis Procedure .............................................146 SIDE TURN SIGNAL LAMP ............................. 170
Exploded View ...................................................... 170
TAIL LAMP CIRCUIT ....................................... 147 Removal and Installation ....................................... 170
Component Function Check ..................................147 Replacement ......................................................... 170
Diagnosis Procedure .............................................147
HAZARD SWITCH ............................................ 172
LICENSE PLATE LAMP CIRCUIT .................. 149 Exploded View ...................................................... 172
Component Function Check ..................................149 Removal and Installation ....................................... 172
Diagnosis Procedure .............................................149
REAR COMBINATION LAMP .......................... 173
REAR FOG LAMP CIRCUIT ............................ 150 Exploded View ...................................................... 173
Component Function Check ..................................150 Removal and Installation ....................................... 173
Diagnosis Procedure .............................................150 Replacement ......................................................... 174
EXL
Check the vehicle type (refer to GI-32, "Model Variation") to use the service information in this section.
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000007152123
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000007084690
K
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables. EXL
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing M
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro- N
cedure below before starting the repair operation.
OPERATION PROCEDURE
O
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position. P
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000007040987
B
JMLIA2806ZZ K
23. Front fog lamp relay*5 Power supply is provided to front fog lamp.
*1: With Intelligent Key system
*2
: With remote keyless entry system or Intelligent Key system (Except for Hong Kong)
*3
: Without Intelligent Key system
*4
: With position lamp indicator lamp
*5: With front fog lamp system
*6
: With rear fog lamp system
*7
: With headlamp aiming control
*8
: With remote keyless entry system or Intelligent Key system (For Hong Kong)
Headlamp Aiming Switch INFOID:0000000007871473
JMLIA2582GB
A
• Headlamp aiming motor is integrated in the front combination
lamp.
• Headlamp aiming motor adjusts the headlamp light axis upward B
and downward according to input drive signal from headlamp aim-
ing switch.
D
JMLIA2392ZZ
H
JMLIA2580GB
SYSTEM DIAGRAM
JPLIA0167GB
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
FOLLOW ME HOME FUNCTION (FOR INDIA PRODUCTION MODELS)
When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow
me home function of BCM.
• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits
the low beam request signal for a period of time to IPDM E/R through CAN communication.
Follow me home ON condition
- Ignition switch OFF
- Lighting switch OFF
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
EXL
JMLIA2562GB
SYSTEM DIAGRAM
F
J
JPLIA0180GB
OUTLINE
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the K
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION
EXL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
M
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard
warning lamps.
N
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn indicator signal to the combination meter using CAN communication while the turn
signal lamp and the hazard warning lamp are operating.
O
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn indicator signal.
HIGH FLASHER OPERATION P
• BCM detects the turn signal lamp circuit status from the current value.
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
JMLIA2624GB
SYSTEM DIAGRAM
B
F
JMLIA2551GB
OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con- G
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION H
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter* via CAN communi-
cation according to the ON/OFF condition of the parking, license plate and tail lamps.
I
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON J
according to the position light request signal.
• Combination meter turns the position lamp indicator lamp ON according to the position light request signal*.
*: With position lamp indicator lamp K
EXL
JMLIA2705GB
SYSTEM DIAGRAM
D
JMLIA0970GB
OUTLINE I
Front fog lamp is controlled by combination switch reading function and front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION J
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the front fog lamp ON condition. K
Front fog lamp ON condition
- Front fog lamp switch ON, and any of the following conditions is satisfied.
• Lighting switch 1ST EXL
• Lighting switch 2ND
IPDM E/R turns the front fog lamp relay ON, and turns the front fog lamp ON according to the front fog light
request signal. M
Combination meter turns the front fog lamp indicator lamp ON according to the front fog light request signal.
JMLIA2565GB
SYSTEM DIAGRAM C
JPLIA0179GB
H
OUTLINE
Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function
of BCM.
I
REAR FOG LAMP OPERATION
• BCM detects the condition of the combination switch by the combination switch reading function.
• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.
J
Rear fog lamp ON condition
- Rear fog lamp switch is turned from OFF to ON, while front fog lamp is ON.
• BCM transmits the rear fog lamp status signal to the combination meter using CAN communication. K
• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal.
EXL
JMLIA2566GB
A
SYSTEM DIAGRAM
JMLIA2071GB
G
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM H
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
I
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamp* OFF, according to the vehicle status when ignition switch is turned OFF while J
exterior lamp is ON, for preventing battery discharge.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp, front fog lamp (with front fog lamp) and rear
fog lamp (with rear fog lamp)
K
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (exterior battery saver is activated) when all of the following conditions are
satisfied.
EXL
• Ignition switch is OFF position*1.
• Key switch is OFF*2.
• BCM detects door lock signal (auto door lock function*3, each door request switch*1, remote keyless entry M
receiver*3)
When in any of following conditions (after the exterior lamp battery saver is activated), exterior lamps (except
rear fog lamp) can be turned ON.
N
• Ignition switch is turned from OFF→ON*1
• Key switch is turned from OFF→ON*2
• Front door switch (driver side) is turned from OFF→ON
O
• Lighting switch is changed
1
* : With Intelligent Key
*2: Without Intelligent Key
P
*3: With remote keyless entry system or Intelligent Key
JMLIA2807GB
SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
K
WORK SUPPORT
MODE 5 C
MODE 6
Monitor item
Description H
[Unit]
PUSH SW
The switch status input from push-button ignition switch.
[On/Off]
ENGINE STATE I
The engine status received from ECM using CAN communication.
[Stop/Stall/Crank/Run]
VEH SPEED 1 The value of the vehicle speed received from combination meter using CAN commu-
[km/h] nication. J
TURN SIGNAL R
Each switch status that BCM judges from the combination switch reading function.
[On/Off]
TURN SIGNAL L K
[On/Off]
TAIL LAMP SW
[On/Off] EXL
HI BEAM SW
[On/Off]
HEAD LAMP SW1 M
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
HEAD LAMP SW2
[On/Off] N
PASSING SW
[On/Off]
FR FOG SW O
[On/Off]
RR FOG SW
[On/Off]
P
DOOR SW-DR
The switch status input from front door switch. (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch. (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH.
[On/Off]
ACTIVE TEST
*1: For models without front fog lamp, this item is displayed but is not tested.
*2: For models without rear fog lamp, this item is displayed but is not tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) INFOID:0000000006654440
WORK SUPPORT
Monitor item A
Description
[Unit]
REQ SW-DR
The switch status input from the request switch (driver side)
[On/Off]
B
REQ SW-AS
The switch status input from the request switch (passenger side)
[On/Off]
PUSH SW C
The switch status input from the push-button ignition switch
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function D
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch E
[On/Off]
RKE-LOCK
Lock signal status received from the remote keyless entry receiver
[On/Off]
F
RKE-UNLOCK
Unlock signal status received from the remote keyless entry receiver
[On/Off]
RKE-PANIC
Panic alarm signal status received from the remote keyless entry receiver G
[On/Off]
ACTIVE TEST
H
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. I
Off Stops the voltage to turn the turn signal lamps OFF.
EXL
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
• Automatic air conditioning
AIR CONDITONER ×
• Manual air conditioning
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER × ×
Trunk lid open TRUNK ×
Theft warning alarm THEFT ALM*1 × ×
— RETAINED PWR*2
Signal buffer system SIGNAL BUFFER × ×
Panic alarm PANIC ALARM ×
*1: For models without theft warning alarm this mode is not used.
*2: This item is displayed, but is not used.
HEADLAMP
A
WORK SUPPORT
MODE 5
MODE 6 F
*1: For models for India production models, this item is displayed.
*2: Factory setting G
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable H
to this vehicle, refer to CONSULT display items.
Monitor item
Description I
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal. (ignition power supply)
[On/Off]
J
ACC ON SW
Ignition switch (ACC) status judged from ACC signal. (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter using CAN commu-
[km/h] nication. K
HI BEAM SW
[On/Off]
EXL
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
Each switch status that BCM judges from the combination switch reading function. M
[On/Off]
PASSING SW
[On/Off]
FR FOG SW N
[On/Off]
AUTO LIGHT SW NOTE:
[On/Off] The item is indicated, but not monitored. O
RR FOG SW
Each switch status that BCM judges from the combination switch reading function.
[On/Off]
DOOR SW-DR P
The switch status input from front door switch. (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch. (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH.
[On/Off]
ACTIVE TEST
*1: For models without front fog lamp, this item is displayed but is not tested.
*2: For models without rear fog lamp, this item is displayed but is not tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) INFOID:0000000006654443
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor item A
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
B
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L C
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off]
D
ACTIVE TEST
EXL
Operation
Inspection location Operation
sequence
Blink continuously during operation of auto active test
NOTE:
1 Oil pressure warning lamp
Except for HR12DE engine models, turn ON continuously during of auto active
test.
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
3 10 seconds
• Tail lamp
• Front fog lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
JMMIA0812GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica- H
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
I
Diagnosis Chart in Auto Active Test
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
ACTIVE TEST
EXL
Test item Operation Description
HORN On Operates horn relay for 20 ms.
Off OFF M
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF N
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
O
4 Operates the cooling fan relay (HI operation).
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested. P
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay
Hi
at 1 second ON/OFF intervals.
Fog Operates the front fog lamp relay.
Operation
Inspection location Operation
sequence
Blink continuously during operation of auto active test
NOTE:
1 Oil pressure warning lamp
Except for HR12DE engine models, turn ON continuously during of auto active
test.
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
• License plate lamp
3 10 seconds
• Tail lamp
• Front fog lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
JMMIA0354GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated. G
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
EXL
ECU Reference
BCS-36, "Reference Value"
BCS-58, "Fail-safe"
BCM
BCS-60, "DTC Inspection Priority Chart"
BCS-61, "DTC Index"
PCS-16, "Reference Value"
IPDM E/R PCS-22, "Fail-safe"
PCS-23, "DTC Index"
ECU Reference
BCS-115, "Reference Value"
BCS-129, "Fail-safe"
BCM
BCS-130, "DTC Inspection Priority Chart"
BCS-130, "DTC Index"
PCS-52, "Reference Value"
IPDM E/R PCS-57, "Fail-safe"
PCS-58, "DTC Index"
WIRING DIAGRAM A
EXTERIOR LIGHTING SYSTEM
Wiring Diagram INFOID:0000000006654449
B
For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".
C
EXL
JRLWC1804GB
JRLWC1805GB
EXL
JRLWC1806GB
JRLWC1807GB
EXL
JRLWC1808GB
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000007871468
OVERALL SEQUENCE
JMKIA8652GB
DETAILED FLOW
>> GO TO 2.
2.CHECK DTC C
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC and freeze frame data (Print them out using CONSULT.) D
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information. E
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4. F
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer. G
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
H
>> GO TO 5.
4.CONFIRM THE SYMPTOM I
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
J
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected K
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-60, "DTC Inspection Priority Chart" and determine trouble
diagnosis order. EXL
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
M
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE. N
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-42, "Intermittent Incident". O
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step P
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES >> GO TO 7.
NO >> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Revision: 2012 July EXL-49 N17
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 1]
Inspect according to Diagnostic Procedure of the system.
Is malfunctioning part detected?
YES >> GO TO 8.
NO >> Check according to GI-42, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO >> Before returning the vehicle to the customer, always erase DTC.
DTC/CIRCUIT DIAGNOSIS A
HEADLAMP (HI) CIRCUIT
Component Function Check INFOID:0000000006654452
B
(+) J
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
K
Hi Battery voltage
RH 63
Off 0V
E35 Ground EXTERNAL LAMPS
Hi Battery voltage EXL
LH 61
Off 0V
Is the inspection result normal?
M
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT N
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector. O
IPDM E/R Headlamp
Continuity
Connector Terminal Connector Terminal
P
RH 63 E45
E35 1 Existed
LH 61 E46
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 63
E35 Not existed
LH 61
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF D
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
E
NO >> Refer to EXL-53, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000006654455
F
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn ignition switch OFF. G
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item. H
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.
With Stop/Start system
(+)
I
(−) Voltage
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage J
RH 40
Off 0V
E32 Ground EXTERNAL LAMPS
Lo Battery voltage
LH 39 K
Off 0V
Headlamp
Continuity
Connector Terminal D
Ground
RH E45
2 Existed
LH E46
E
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
F
EXL
0 A: 1000 Ω
1 B: 560 Ω
2
1 2 C: 390 Ω
3 D: 270 Ω
3 — E: 390 Ω JSLIA0084ZZ
F
1.CHECK PARKING LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal? G
YES >> GO TO 2.
NO >> Replace the bulb.
2.CHECK PARKING LAMP OPEN CIRCUIT H
Check continuity between license plate lamp harness connector and ground.
M
License plate lamp
Continuity
Connector Terminal
Ground
RH B36 N
2 Existed
LH B35
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary. O
NO >> Repair or replace harness.
(+)
Voltage
Front fog lamp (−) Test item
(Approx.)
Connector Terminal
Fog Battery voltage
RH E55
Off 0V
1 Ground EXTERNAL LAMPS
Fog Battery voltage
LH E56
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK FRONT FOG LAMP GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between front fog lamp harness connector and ground.
EXL
(+)
Voltage
Front fog lamp relay (–)
(Approx.)
Connector Terminal
2
E85 Ground Battery voltage
5
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK FRONT FOG LAMP RELAY CIRCUIT 1
CONSULT ACTIVE TEST
1. Install front fog lamp relay.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.
(+)
Voltage
IPDM E/R (–) Test item
(Approx.)
Connector Terminal
EXTERNAL Fog 0V
E34 21 Ground
LAMPS Off Battery voltage
Is the inspection result normal?
YES >> GO TO 5.
NO-1 >> (Fixed battery voltage) Replace IPDM E/R.
NO-2 >> (Fixed 0 V) GO TO 4.
4.CHECK FRONT FOG LAMP RELAY CIRCUIT 2
1. Remove front fog lamp relay.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front fog lamp relay harness connector.
Terminal
Condition Continuity I
Front fog lamp relay
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
J
No current supply Not existed
Is the inspection result normal?
YES >> INSPECTION END K
NO >> Replace front fog lamp relay.
SEF497Y
EXL
(+)
Voltage
Rear combination lamp LH (−) Test item
(Approx.)
Connector Terminal
On 12 V
B14 2 Ground RR FOG LAMP
Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK REAR FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear combination lamp LH harness connector.
With Intelligent Key
BCM Rear combination lamp LH
Continuity
Connector Terminal Connector Terminal
M63 52 B14 2 Existed
EXL
LH
60
PKIC6370E
6.0V
RH
61
PKIC6370E
6.0V
OFF 0V
C
LH
60
PKIC6370E
D
6.0V
F
RH
61
G
PKIC6370E
6.0V
OFF 0V
H
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4. I
3.CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector. J
3. Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.
Front turn signal lamp (With Intelligent Key) K
BCM Front turn signal lamp
Continuity
Connector Terminal Connector Terminal
EXL
RH 61 E47
M59 2 Existed
LH 60 E48
EXL
(+)
Hazard switch (−) Voltage (Approx.)
Connector Terminal
M44 2 Ground 12 V
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.
With Intelligent Key
Hazard switch BCM
Continuity
Connector Terminal Connector Terminal
M44 2 M65 29 Existed
Hazard switch A
Continuity
Connector Terminal Ground
M44 2 Not existed
B
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-82, "Removal and Installation" (with Intelligent Key) or BCS-147,
"Removal and Installation" (without Intelligent Key).
NO >> Repair or replace harness. C
Hazard switch
Continuity
Connector Terminal Ground E
M44 1 Existed
Is the inspection result normal?
F
YES >> Replace hazard switch.
NO >> Repair or replace harness.
EXL
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000006654474
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure INFOID:0000000006654476
EXL
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure INFOID:0000000006654480
1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
IPDM E/R
Continuity
Connector Terminal Ground
E35 59 Not existed
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
NO >> Repair or replace harness. And then replace the fuse.
3.COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to BCS-81, "Symptom Table" (with Intelligent Key), BCS-146, "Symptom
Table" (without Intelligent Key).
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning part.
4.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Turn ignition switch ON.
2. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
3. With operating the lighting switch, check the monitor status.
EXL
PERIODIC MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
LHD
B
LHD : Description INFOID:0000000006654483
EXL
JMLIA2039ZZ P
JSLIA0030ZZ
JSLIA0031ZZ F
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
G
(lateral) (Vertical)
RHD K
RHD : Description INFOID:0000000007802984
EXL
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been M
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification. N
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.) O
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
P
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JMLIA2039ZZ
JSLIA0028ZZ
E
A. Aiming adjustment area
B. Elbow point
C. Headlamp center F
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
G
JSLIA0029ZZ
EXL
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
(lateral) (Vertical) M
A: UP
B: DOWN
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
JMLIA2040ZZ
JPLIA0008ZZ
A : Cutoff line A
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp B
X : Cutoff line height
EXL
REMOVAL
JMLIA2041GB
DISASSEMBLY
JMLIA2042ZZ
1. Headlamp housing assembly 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Back cover 5. Halogen bulb 6. Front turn signal lamp bulb socket
7. Front turn signal lamp bulb 8. Retaining spring
REMOVAL
CAUTION:
Disconnect the battery negative terminal or the fuse to prevent electric leakage.
1. Remove front bumper fascia. Refer to EXT-13, "FRONT BUMPER : Removal and Installation".
Replacement INFOID:0000000006654491
CAUTION: D
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• After installing the bulb, install the back cover and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to E
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
F
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect the headlamp bulb connector. G
2. Remove the back cover.
3. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
H
PARKING LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket. I
FRONT TURN SIGNAL LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
J
2. Remove the bulb from the bulb socket.
Disassembly and Assembly INFOID:0000000006654492
K
DISASSEMBLY
1. Remove the back cover.
2. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly. EXL
3. Rotate the parking lamp bulb socket counterclockwise and unlock it.
4. Remove the bulb from the parking lamp bulb socket.
M
5. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY N
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness. O
JMLIA2043ZZ
1. Front fog lamp bulb 2. Front fog lamp 3. Front bumper fascia assembly
4. Front fog lamp finisher
: Pawl
CAUTION:
Disconnect the battery negative terminal or the fuse to prevent electric leakage.
REMOVAL
1. Remove the fender protector. Refer to EXT-22, "FENDER PROTECTOR : Removal and Installation".
2. Remove the front fog lamp connector.
3. Remove the fixing screws, and then remove front fog lamp.
INSTALLATION
Note the following item and install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-84, "Description".
Replacement INFOID:0000000006654496
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1. Remove the fender protector. Keep the service area.Refer to EXT-22, "FENDER PROTECTOR : Removal
and Installation".
SKIB8304J
EXL
The lighting & turn switch is integrated in the combination switch. Refer to BCS-83, "Removal and Installation".
JPLIA1809ZZ
1. Side turn signal lamp bulb socket 2. Side turn signal lamp bulb 3. Side turn signal lamp housing G
H
CAUTION:
Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL I
1. Remove the side turn signal lamp in numerical order as shown in the figure.
JMLIA1302ZZ
M
INSTALLATION
1. Rotate the bulb socket clockwise and lock it.
2. Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side. N
Replacement INFOID:0000000006654500
CAUTION: O
• Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb. P
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1. Remove the side turn signal lamp. Refer to EXL-91, "Removal and Installation".
2. Rotate the bulb socket counterclockwise and unlock it.
JMLIA2056ZZ
REMOVAL
I
1. Remove the cluster lid C. Refer to IP-12, "Exploded View".
2. While pressing pawls, push the hazard switch to remove it.
INSTALLATION J
Install in the reverse order of removal.
EXL
REMOVAL
JMLIA2044ZZ
DISASSEMBLY
JMLIA2683ZZ
1. Rear combination lamp RH 2. Stop/tail lamp bulb RH 3. Back-up lamp bulb (LHD)
4. Bulb holder RH 5. Rear turn signal lamp bulb RH 6. Bulb holder LH
7. Stop/tail lamp bulb LH 8. Rear combination lamp LH 9. Back-up lamp bulb (RHD)/Rear fog
lamp bulb (LHD)
10. Rear turn signal lamp bulb LH
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
JMLIA2046ZZ E
3. Disconnect rear combination lamp connector, and then remove rear combination lamp.
INSTALLATION F
Install in the reverse order of removal.
Replacement INFOID:0000000006654505
G
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to H
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one. I
EXL
M
JMLIA2684ZZ
3. Rotate stop/tail lamp bulb counterclockwise, and then remove stop/tail lamp bulb. N
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-94, "Removal and Installation".
O
2. Disengage fixing screws (A), and then remove bulb holder.
JMLIA2684ZZ
3. Rotate rear turn signal lamp bulb counterclockwise, and then remove rear turn signal lamp bulb.
BACK-UP LAMP BULB / REAR FOG LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-94, "Removal and Installation".
2. Disengage fixing screws (A), and then remove bulb holder.
JMLIA2684ZZ
3. Rotate back-up lamp bulb / rear fog lamp bulb counterclockwise, and then remove back-up lamp bulb /
rear fog lamp bulb.
G
JMLIA2556ZZ
EXL
N
JMLIA2054ZZ
1. Rear parcel shelf finisher 2. High-mounted stop lamp socket 3. High-mounted stop lamp bulb
4. High-mounted stop lamp housing O
: Pawl
CAUTION:
Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
With rear spoiler models
1. Remove rear spoiler. Refer to EXT-27, "Removal and Installation".
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB
1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the bulb socket.
G
JMLIA2055ZZ
CAUTION: I
Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
1. While pressing the license plate lamp housing fixing pawl to direction right side, pull it to direction lower J
side and then remove it.
2. Rotate the bulb socket counterclockwise, and then remove bulb socket.
3. Remove the license plate lamp housing. K
INSTALLATION
Install in the reverse order of removal.
EXL
Replacement INFOID:0000000006654513
CAUTION: M
• Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage of the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns. N
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB O
1. Remove the license plate lamp housing.
2. Remove the bulb from the socket.
P
JMLIA2053ZZ
REMOVAL
1. Remove switch panel. Refer to IP-13, "Removal and Installation".
2. Disengage the headlamp aiming switch harness connector and mirror control switch harness connector (if
so equipped).
3. Remove the headlamp aiming switch from switch panel.
INSTALLATION
Install in the reverse order of removal.
EXL
Check the vehicle type (refer to GI-32, "Model Variation") to use the service information in this section.
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000007995357
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000007995358
K
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables. EXL
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing M
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro- N
cedure below before starting the repair operation.
OPERATION PROCEDURE
O
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position. P
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000007995361
B
JMLIA2698ZZ K
JMLIA2582GB
A
• Headlamp aiming motor is integrated in the front combination
lamp.
• Headlamp aiming motor adjusts the headlamp light axis upward B
and downward according to input drive signal from headlamp aim-
ing switch.
D
JMLIA2392ZZ
H
JMLIA2580GB
SYSTEM DIAGRAM
JPLIA0167GB
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
FOLLOW ME HOME FUNCTION
When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow
me home function of BCM.
• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits
the low beam request signal for a period of time to IPDM E/R through CAN communication.
Follow me home ON condition
- Ignition switch OFF
- Lighting switch OFF
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
EXL
JMLIA2699GB
SYSTEM DIAGRAM
F
J
JPLIA0180GB
OUTLINE
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the K
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION
EXL
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
M
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard
warning lamps.
N
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn indicator signal to the combination meter using CAN communication while the turn
signal lamp and the hazard warning lamp are operating.
O
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn indicator signal.
3-TIME FLASHER FUNCTION P
• By a short touch of the turn signal lever, BCM blinks the turn signal lamps 3 times in the selected direction.
• Cancel the operation when short touch of the turn signal lever in the reverse direction during the 3-time
flasher function operating.
HIGH FLASHER OPERATION
• BCM detects the turn signal lamp circuit status from the current value.
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
JMLIA2700GB
SYSTEM DIAGRAM
B
JMLIA2711GB G
OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con-
trol function of BCM, and relay control function of IPDM E/R. H
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter* via CAN communi- I
cation according to the ON/OFF condition of the parking, license plate and tail lamps.
Parking, license plate and tail lamps ON condition J
- Lighting switch 1ST
- Lighting switch 2ND
• IPDM E/R turns the tail lamp relay, tail lamp RH relay, and tail lamp LH relay ON according to the position
light request signal. The parking, license plate and tail lamps turn ON. K
• Combination meter turns the position lamp indicator lamp ON according to the position light request signal*.
*: With position lamp indicator lamp
EXL
JMLIA2701GB
SYSTEM DIAGRAM
D
JPLIA0179GB
OUTLINE I
Rear fog lamp is controlled with the combination switch reading function and the rear fog lamp control function
of BCM.
REAR FOG LAMP OPERATION J
• BCM detects the condition of the combination switch by the combination switch reading function.
• BCM supplies voltage to rear fog lamp according to the rear fog lamp ON condition.
K
Rear fog lamp ON condition
- When rear fog lamp switch is turned from OFF to ON with headlamp ON.
• BCM transmits the rear fog lamp status signal to the combination meter with CAN communication.
• Combination meter turns the rear fog lamp indicator lamp ON according to the rear fog lamp status signal. EXL
JMLIA2702GB
A
SYSTEM DIAGRAM
JMLIA2710GB F
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
G
Control by BCM
- Combination switch reading function
- Headlamp control function H
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function I
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, license plate lamp and rear fog lamp
J
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM turns the exterior lamps OFF (battery saver is activated) when all of the following conditions are satisfied.
• Exterior lamps ON K
• When any of the following conditions is satisfied.
- Driver side door switch is turned from OFF to ON while ignition switch is OFF.
- Ignition switch is turned from ON to OFF while driver side door switch is ON.
NOTE: EXL
When following condition (after the exterior lamp battery saver is activated), exterior lamps can be turned ON.
• Lighting switch ON→ OFF → ON
M
JMLIA2703GB
SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
K
*1: For models without theft warning alarm this mode is not used.
*2: This item is displayed, but is not used.
HEADLAMP
WORK SUPPORT
Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
ACC SW
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter with CAN commu-
[km/h] nication
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
FR FOG SW NOTE:
[On/Off] This item is indicated, but can not monitored
AUTO LIGHT SW NOTE:
[On/Off] This item is indicated, but can not monitored
RR FOG SW
Each switch status that BCM judges from the combination switch reading function
[On/Off]
DOOR SW-DR
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off]
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL
The switch status input from rear door switch LH
[On/Off]
BACK DOOR SW NOTE:
[On/Off] This item is indicated, but can not monitored
TURN SIGNAL R
[On/Off]
TURN SIGNAL L
Each switch status that BCM judges from the combination switch reading function
[On/Off]
TAIL LAMP SW
[On/Off]
DATA MONITOR
NOTE: EXL
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
M
Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply) N
[On/Off]
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function O
TURN SIGNAL L
[On/Off]
HAZARD SW
The switch status input from the hazard switch
[On/Off] P
ACTIVE TEST
Operation N
Inspection location Operation
sequence
Blink continuously during operation of auto active test
NOTE:
1 Oil pressure warning lamp O
Except for HR12DE engine models, turn ON continuously during of auto active
test.
2 Front wiper LO for 5 seconds → HI for 5 seconds
P
• Parking lamp
• License plate lamp
3 10 seconds
• Tail lamp
• Front fog lamp
4 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
JMMIA0354GB
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis Chart in Auto Active Test
A
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
B
Diagnosis mode Description
Ecu Identification Allows confirmation of IPDM E/R part number.
Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R. C
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
D
CAN Diag Support Monitor The results of transmit/receive diagnosis of CAN communication can be read.
ACTIVE TEST
ECU Reference
C
BCS-115, "Reference Value"
BCS-129, "Fail-safe"
BCM
BCS-130, "DTC Inspection Priority Chart" D
BCS-130, "DTC Index"
PCS-52, "Reference Value"
E
IPDM E/R PCS-57, "Fail-safe"
PCS-58, "DTC Index"
EXL
WIRING DIAGRAM
EXTERIOR LIGHTING SYSTEM
Wiring Diagram INFOID:0000000007995425
For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".
JRLWC1804GB
EXL
JRLWC1805GB
JRLWC1806GB
EXL
JRLWC1807GB
JRLWC1808GB
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000007995426
B
OVERALL SEQUENCE
C
EXL
JMKIA8652GB
DETAILED FLOW
>> GO TO 2.
2.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is detected.
- Record DTC and freeze frame data (Print them out using CONSULT.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to BCS-60, "DTC Inspection Priority Chart" and determine trouble
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES >> GO TO 7.
NO >> Check according to GI-42, "Intermittent Incident".
6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES >> GO TO 7.
NO >> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Revision: 2012 July EXL-134 N17
DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [TYPE 2]
Inspect according to Diagnostic Procedure of the system.
Is malfunctioning part detected? A
YES >> GO TO 8.
NO >> Check according to GI-42, "Intermittent Incident".
8.REPAIR OR REPLACE THE MALFUNCTIONING PART B
D
>> GO TO 9.
9.FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the E
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected. F
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4. G
NO >> Before returning the vehicle to the customer, always erase DTC.
EXL
DTC/CIRCUIT DIAGNOSIS
HEADLAMP (HI) CIRCUIT
Component Function Check INFOID:0000000007995430
Hi : Headlamp (HI) ON
Off : Headlamp (HI) OFF
NOTE:
ON/OFF is repeated 1 second each.
Is the inspection result normal?
YES >> Headlamp (HI) circuit is normal.
NO >> Refer to EXL-136, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000007995431
(+)
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
Hi Battery voltage
RH 63
Off 0V
E35 Ground EXTERNAL LAMPS
Hi Battery voltage
LH 61
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.
IPDM E/R
Continuity F
Connector Terminal
Ground
RH 63
E35 Not existed
LH 61 G
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse. H
EXL
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
NO >> Refer to EXL-138, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000007995433
(+)
(−) Voltage
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage
RH 40
Off 0V
E32 Ground EXTERNAL LAMPS
Lo Battery voltage
LH 38
Off 0V
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.
IPDM E/R
Continuity
Connector Terminal E
Ground
RH 40
E32 Not existed
LH 38
F
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
G
EXL
Headlamp
Continuity
Connector Terminal
Ground
RH E45
2 Existed
LH E46
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
(+)
Voltage
Tail lamp LH relay (–) G
(Approx.)
Connector Terminal
E54 5 Ground Battery voltage
H
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
I
3.CHECK TAIL LAMP LH RELAY POWER SUPPLY CIRCUIT 2
CONSULT ACTIVE TEST
1. Turn ignition switch ON. J
2. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
3. With operating the test items, check voltage between tail lamp LH relay harness connector and ground.
K
(+)
Voltage
Tail lamp LH relay (–) Test item
(Approx.)
Connector Terminal EXL
EXTERNAL TAIL Battery voltage
E54 2 Ground
LAMPS Off 0V
M
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
N
4.CHECK TAIL LAMP LH RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector. O
3. Check continuity between IPDM E/R harness connector and tail lamp LH relay harness connector.
Terminal
Condition Continuity
tail lamp LH relay
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace tail lamp LH relay.
SEF497Y
(+)
Voltage
Tail lamp RH relay (–) G
(Approx.)
Connector Terminal
E53 5 Ground Battery voltage
H
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
I
3.CHECK TAIL LAMP RH RELAY POWER SUPPLY CIRCUIT 2
CONSULT ACTIVE TEST
1. Turn ignition switch ON. J
2. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
3. With operating the test items, check voltage between tail lamp RH relay harness connector and ground.
K
(+)
Voltage
Tail lamp RH relay (–) Test item
(Approx.)
Connector Terminal EXL
EXTERNAL TAIL Battery voltage
E53 2 Ground
LAMPS Off 0V
M
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
N
4.CHECK TAIL LAMP RH RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector. O
3. Check continuity between IPDM E/R harness connector and tail lamp RH relay harness connector.
Terminal
Condition Continuity
tail lamp RH relay
12 V direct current supply between termi-
Existed
3 5 nals 1 and 2
No current supply Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace tail lamp RH relay.
SEF497Y
F
Is the inspection result normal?
YES >> Headlamp aiming switch is normal.
NO >> Replace the headlamp aiming switch.
G
EXL
NOTE:
Check tail lamp RH relay circuit first if the parking lamp, the tail lamp RH, and the license plate lamp are not
turned ON.
Tail lamp RH relay circuit: Refer to EXL-143, "Diagnosis Procedure".
1.CHECK PARKING LAMP OPERATION
CONSULT ACTIVE TEST
1. Select “TAIL LAMP” of BCM(HEADLAMP) active test item.
2. With operating the test items, check that the parking lamp is turned ON.
On : Parking lamp ON
Off : Parking lamp OFF
Is the inspection result normal?
YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-146, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000007995993
Parking lamp
Continuity
Connector Terminal
Ground
RH E52
1 Existed
LH E51
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
NOTE: B
Check tail lamp RH and LH relay circuit first if the parking lamp, the tail lamp, and the license plate lamp are
not turned ON.
• Tail lamp RH relay circuit: Refer to EXL-143, "Diagnosis Procedure".
• Tail lamp LH relay circuit: Refer to EXL-141, "Diagnosis Procedure". C
1.CHECK TAIL LAMP OPERATION
CONSULT ACTIVE TEST D
1. Select “TAIL LAMP” of BCM(HEADLAMP) active test item.
2. With operating the test items, check that the tail lamp is turned ON.
E
ON : Tail Lamp ON
Off : Tail lamp OFF
Is the inspection result normal? F
YES >> Tail lamp circuit is normal.
NO >> Refer to EXL-147, "Diagnosis Procedure".
G
Diagnosis Procedure INFOID:0000000007995995
NOTE: B
Check tail lamp RH relay circuit first if the parking lamp, the tail lamp RH, and the license plate lamp are not
turned ON.
• Tail lamp RH relay circuit: Refer to EXL-143, "Diagnosis Procedure".
C
1.CHECK LICENSE PLATE LAMP OPERATION
CONSULT ACTIVE TEST
1. Select “TAIL LAMP” of BCM(HEADLAMP) active test item. D
2. With operating the lighting switch, check that the license plate lamp is turned ON.
(+)
Voltage
Rear combination lamp RH (−) Test item
(Approx.)
Connector Terminal
On 12 V
B13 2 Ground RR FOG LAMP
Off 0V
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK REAR FOG LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and rear combination lamp RH harness connector.
EXL
(+)
Voltage
BCM (–) Condition
(Approx.)
Connector Terminal
LH
60
PKIC6370E
6.0V
RH
61
PKIC6370E
6.0V
OFF 0V
Is the inspection result normal?
BCM K
Continuity
Connector Terminal
Ground
RH 61
M60 Not existed EXL
LH 60
Is the inspection result normal?
YES >> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer M
to BCS-147, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT N
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.
Front turn signal lamp O
Front turn signal lamp
Continuity
Connector Terminal
Ground P
RH E47
1 Existed
LH E48
(+)
Hazard switch (−) Voltage (Approx.) I
Connector Terminal
M44 2 Ground 12 V
J
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
K
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector. EXL
Hazard switch
Continuity P
Connector Terminal Ground
M44 2 Not existed
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-147, "Removal and Installation".
NO >> Repair or replace harness.
Hazard switch
Continuity
Connector Terminal Ground
M44 1 Existed
Is the inspection result normal?
YES >> Replace hazard switch.
NO >> Repair or replace harness.
SYMPTOM DIAGNOSIS A
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000007995998
B
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected. C
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS. B
Diagnosis Procedure INFOID:0000000007995454
EXL
The parking, license plate, tail lamps and each illumination are not turned ON in any condition. B
Diagnosis Procedure INFOID:0000000007996000
Check the tail lamp LH relay circuit. Refer to EXL-141, "Diagnosis Procedure".
Is the inspection result normal? O
YES >> Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace the malfunctioning part.
P
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description INFOID:0000000007995465
JMLIA2039ZZ
E
1. Place the screen.
NOTE:
• Stop the vehicle at the perpendicular angle to the wall.
F
• Set the screen so that it is perpendicular to a level load surface.
2. Face the vehicle squarely toward the screen and make the distance between the headlamp center and
the screen 10 m (32.8 ft).
G
3. Start the engine and illuminate the headlamp (LO).
NOTE:
Block light from the headlamp that is not being adjusted with a thick fabric or another object, so that it
does not reach the adjustment screen. H
CAUTION:
Do not cover lens surface with tape, etc. because it is made from plastic.
4. Use the aiming adjustment screw to adjust the elbow point projected by the low beams on the screen, so I
that it is within the aiming adjustment area.
Low beam distribution on the screen
J
EXL
JSLIA0028ZZ
M
A. Aiming adjustment area
B. Elbow point
C. Headlamp center N
H. Horizontal center line of headlamp
V. Vertical center line of headlamp
O
JSLIA0029ZZ
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
(lateral) (Vertical)
JMLIA2040ZZ
J
Aiming Adjustment Procedure INFOID:0000000007995468
JPLIA0008ZZ
A : Cutoff line
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp
X : Cutoff line height
REMOVAL
C
H
JMLIA2041GB
DISASSEMBLY
J
EXL
JMLIA2042ZZ
O
1. Headlamp housing assembly 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Back cover 5. Halogen bulb 6. Front turn signal lamp bulb socket
7. Front turn signal lamp bulb 8. Retaining spring P
REMOVAL
CAUTION:
Disconnect the battery negative terminal or the fuse to prevent electric leakage.
1. Remove front bumper fascia. Refer to EXT-13, "FRONT BUMPER : Removal and Installation".
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• After installing the bulb, install the back cover and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect the headlamp bulb connector.
2. Remove the back cover.
3. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
PARKING LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1. Rotate the bulb socket counterclockwise and unlock it.
2. Remove the bulb from the bulb socket.
Disassembly and Assembly INFOID:0000000007995472
DISASSEMBLY
1. Remove the back cover.
2. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
3. Rotate the parking lamp bulb socket counterclockwise and unlock it.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
The lighting & turn switch is integrated in the combination switch. Refer to BCS-83, "Removal and Installation". B
EXL
JPLIA1809ZZ
1. Side turn signal lamp bulb socket 2. Side turn signal lamp bulb 3. Side turn signal lamp housing
CAUTION:
Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
1. Remove the side turn signal lamp in numerical order as shown in the figure.
JMLIA1302ZZ
INSTALLATION
1. Rotate the bulb socket clockwise and lock it.
2. Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side.
Replacement INFOID:0000000007995480
CAUTION:
• Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1. Remove the side turn signal lamp. Refer to EXL-91, "Removal and Installation".
2. Rotate the bulb socket counterclockwise and unlock it.
EXL
JMLIA2056ZZ
REMOVAL
1. Remove the cluster lid C. Refer to IP-12, "Exploded View".
2. While pressing pawls, push the hazard switch to remove it.
INSTALLATION
Install in the reverse order of removal.
REMOVAL B
JMLIA2044ZZ
H
1. Rear combination lamp 2. Grommet
: Clip
DISASSEMBLY I
EXL
JMLIA2683ZZ
O
1. Rear combination lamp RH 2. Stop/tail lamp bulb RH 3. Back-up lamp bulb (RHD)/Rear fog
lamp bulb (RHD)
4. Bulb holder RH 5. Rear turn signal lamp bulb RH 6. Bulb holder LH
P
7. Stop/tail lamp bulb LH 8. Rear combination lamp LH 9. Back-up lamp bulb (LHD)
10. Rear turn signal lamp bulb LH
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
JMLIA2046ZZ
3. Disconnect rear combination lamp connector, and then remove rear combination lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000007995485
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-94, "Removal and Installation".
2. Disengage fixing screws (A), and then remove bulb holder.
JMLIA2684ZZ
3. Rotate stop/tail lamp bulb counterclockwise, and then remove stop/tail lamp bulb.
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-94, "Removal and Installation".
2. Disengage fixing screws (A), and then remove bulb holder.
JMLIA2684ZZ
3. Rotate rear turn signal lamp bulb counterclockwise, and then remove rear turn signal lamp bulb. A
BACK-UP LAMP BULB / REAR FOG LAMP BULB
1. Remove rear combination lamp assembly. Refer to EXL-94, "Removal and Installation".
2. Disengage fixing screws (A), and then remove bulb holder. B
E
JMLIA2684ZZ
3. Rotate back-up lamp bulb / rear fog lamp bulb counterclockwise, and then remove back-up lamp bulb /
rear fog lamp bulb. F
EXL
JMLIA2556ZZ
JMLIA2054ZZ
1. Rear parcel shelf finisher 2. High-mounted stop lamp socket 3. High-mounted stop lamp bulb
4. High-mounted stop lamp housing
: Pawl
CAUTION:
Disconnect battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
With rear spoiler models
1. Remove rear spoiler. Refer to EXT-27, "Removal and Installation".
CAUTION:
• Disconnect the battery negative terminal or the fuse to prevent electric leakage. F
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage to the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns. G
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB H
1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise, and unlock it.
I
3. Remove the bulb from the bulb socket.
EXL
JMLIA2055ZZ
CAUTION:
Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
1. While pressing the license plate lamp housing fixing pawl to direction right side, pull it to direction lower
side and then remove it.
2. Rotate the bulb socket counterclockwise, and then remove bulb socket.
3. Remove the license plate lamp housing.
INSTALLATION
Install in the reverse order of removal.
Replacement INFOID:0000000007995495
CAUTION:
• Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it to
prevent damage of the bulb.
• Never touch bulb by hand while it is ON or right after it is turned off to prevent burns.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1. Remove the license plate lamp housing.
2. Remove the bulb from the socket.
JMLIA2053ZZ
: Pawl
REMOVAL
I
1. Remove switch panel. Refer to IP-13, "Removal and Installation".
2. Disengage the headlamp aiming switch harness connector and mirror control switch harness connector (if
so equipped).
J
3. Remove the headlamp aiming switch from switch panel.
INSTALLATION
Install in the reverse order of removal. K
EXL