Professional Documents
Culture Documents
SECTION
EXTERIOR LIGHTING SYSTEM
EXL B
E
CONTENTS
HALOGEN TYPE EXTERIOR LAMP BATTERY SAVER SYSTEM : F
System Description ................................................... 9
PRECAUTION ............................................... 3
DIAGNOSIS SYSTEM (BCM) ........................... 10
G
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System COMMON ITEM .........................................................10
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- COMMON ITEM : CONSULT Function (BCM -
SIONER" ................................................................... 3 COMMON ITEM) .....................................................10 H
Precautions Necessary for Steering Wheel Rota- HEADLAMP ...............................................................10
tion After Battery Disconnection ................................ 3 HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) ......................................................................11 I
SYSTEM DESCRIPTION .............................. 5
FLASHER ...................................................................12
COMPONENT PARTS ........................................ 5 FLASHER : CONSULT Function (BCM - FLASH-
Component Parts Location ........................................ 5 J
ER) ..........................................................................12
Component Description ............................................ 5
DIAGNOSIS SYSTEM (IPDM E/R) ................... 14
SYSTEM .............................................................. 6 Diagnosis Description ..............................................14 K
HEADLAMP SYSTEM ................................................. 6 CONSULT Function (IPDM E/R) .............................15
HEADLAMP SYSTEM : System Diagram ................. 6
HEADLAMP SYSTEM : System Description ............. 6
ECU DIAGNOSIS INFORMATION .............. 18 EXL
HEADLAMP SYSTEM : Fail-Safe ............................. 6 BCM, IPDM E/R ................................................. 18
TURN SIGNAL AND HAZARD WARNING LAMP List of ECU Reference .............................................18
SYSTEM ...................................................................... 7 M
WIRING DIAGRAM ...................................... 19
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram ...................................... 7 EXTERIOR LIGHTING SYSTEM ...................... 19
TURN SIGNAL AND HAZARD WARNING LAMP Wiring Diagram ........................................................19 N
SYSTEM : System Description ................................. 7
BASIC INSPECTION ................................... 27
PARKING, LICENSE PLATE AND TAIL LAMP
SYSTEM ...................................................................... 7 O
DIAGNOSIS AND REPAIR WORKFLOW ........ 27
PARKING, LICENSE PLATE AND TAIL LAMP Work Flow ................................................................27
SYSTEM : System Diagram ...................................... 8
PARKING, LICENSE PLATE AND TAIL LAMP DTC/CIRCUIT DIAGNOSIS ......................... 29 P
SYSTEM : System Description ................................. 8
PARKING, LICENSE PLATE AND TAIL LAMP HEADLAMP (HI) CIRCUIT ................................ 29
SYSTEM : Fail-Safe .................................................. 8 Component Function Check ....................................29
Diagnosis Procedure ...............................................29
EXTERIOR LAMP BATTERY SAVER SYSTEM ......... 8
EXTERIOR LAMP BATTERY SAVER SYSTEM : HEADLAMP (LO) CIRCUIT .............................. 31
System Diagram ........................................................ 9 Component Function Check ....................................31
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000007221354
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by E
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
F
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING: H
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing I
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service. J
Precautions Necessary for Steering Wheel Rotation After Battery Disconnection
INFOID:0000000007221356
K
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition switch to the LOCK position,
then disconnect both battery cables. EXL
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing M
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro- N
cedure below before starting the repair operation.
OPERATION PROCEDURE
O
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Turn the ignition switch to ACC position. P
(At this time, the steering lock will be released.)
3. Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4. Perform the necessary repair operation.
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000007087507
B
JMLIA2145ZZ
H
1. Combination meter 2. Hazard switch 3. IPDM E/R
Refer to PCS-3, "Component Parts
Location".
I
4. Front turn signal lamp 5. Headlamp 6. Parking lamp
7. BCM 8. Combination switch 9. License plate lamp
Refer to BCS-4, "BODY CONTROL
SYSTEM : Component Parts Loca- J
tion".
10. Tail lamp 11. Rear turn signal lamp
K
Component Description INFOID:0000000007087508
EXL
Part Description
• Detects each switch condition by the combination switch reading function
• Requests the headlamp relay (High/Low) and tail lamp relay ON to IPDM E/R (via
BCM CAN communication) M
• Requests the high beam indicator lamp ON to the combination meter (via CAN com-
munication)
Controls the integrated relay, and supplies voltage to the load according to the request N
IPDM E/R
from BCM (using CAN communication)
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
integrated buzzer according to the request from BCM (via CAN communication).
Combination meter O
• Turns the high beam indicator lamp ON according to the request from BCM (via CAN
communication).
Combination switch
Refer to BCS-6, "COMBINATION SWITCH READING SYSTEM : System Description" P
(Lighting & turn signal switch)
Hazard switch Inputs the hazard switch ON/OFF signal to BCM
JPLIA0167GB
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND
- Lighting switch PASS
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
HEADLAMP SYSTEM : Fail-Safe INFOID:0000000007256977
F
JPLIA0180GB
OUTLINE H
Turn signal lamp and the hazard warning lamp is controlled by combination switch reading function and the
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION I
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamps. J
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard
warning lamps. K
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication
while the turn signal lamp and the hazard warning lamp are operating. EXL
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn signal indicator lamp signal.
HIGH FLASHER OPERATION M
• BCM detects the turn signal lamp circuit status from the current value.
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating. N
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM O
JMLIA0928GB
OUTLINE
Parking, license plate and tail lamps are controlled by combination switch reading function and headlamp con-
trol function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R via CAN communication according to the ON/
OFF condition of the parking, license plate and tail lamps.
Parking, license plate and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate and tail lamps ON
according to the position light request signal.
PARKING, LICENSE PLATE AND TAIL LAMP SYSTEM : Fail-Safe INFOID:0000000007256978
E
JMLIA2146GB
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R. G
Control by BCM
- Combination switch reading function H
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R I
- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp and license plate lamp J
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
• Manual air conditioning system
AIR CONDITONER ×
• Manual heater
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door TRUNK ×
Theft warning alarm THEFT ALM × ×
— RETAINED PWR*
Signal buffer system SIGNAL BUFFER × ×
Panic alarm PANIC ALARM ×
NOTE:
*: This item is displayed, but is not used.
HEADLAMP
A
WORK SUPPORT
MODE 5
E
MODE 6
*
: Factory setting
F
DATA MONITOR
Monitor item
Description G
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
H
ACC ON SW
Ignition switch (ACC) status judged from ACC signal (ACC power supply)
[On/Off]
VEH SPEED The value of the vehicle speed received from combination meter using CAN commu-
[km/h] nication I
HI BEAM SW
[On/Off]
HEAD LAMP SW1 J
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW2
[On/Off] K
PASSING SW
[On/Off]
FR FOG SW NOTE: EXL
[On/Off] The item is indicated, but not monitored
AUTO LIGHT SW NOTE:
[On/Off] The item is indicated, but not monitored M
RR FOG SW NOTE:
[On/Off] The item is indicated, but not monitored
DOOR SW-DR N
The switch status input from front door switch (driver side)
[On/Off]
DOOR SW-AS
The switch status input from front door switch (passenger side)
[On/Off] O
DOOR SW-RR
The switch status input from rear door switch RH
[On/Off]
DOOR SW- RL P
The switch status input from rear door switch LH
[On/Off]
BACK DOOR SW
The switch status input from back door switch
[On/Off]
KEYLESS LOCK* Lock signal status received from remote keyless entry receiver (integrated in the
[On/Off] BCM)
ENGINE RUN
The engine status received from ECM using CAN communication
[On/Off]
OPTI SEN (DTCT) NOTE:
[V] The item is indicated, but not monitored
OPTI SEN (FILT) NOTE:
[V] The item is indicated, but not monitored
*
: For models without remote keyless entry system, this item is displayed but not monitored.
ACTIVE TEST
On NOTE:
RR FOG LAMP
Off The item is indicated, but cannot be tested.
On NOTE:
ILL DIM SIGNAL
Off The item is indicated, but cannot be tested.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) INFOID:0000000007087534
DATA MONITOR
Monitor item
Description
[Unit]
IGN ON SW
Ignition switch (ON) status judged from IGN signal (ignition power supply)
[On/Off]
ACTIVE TEST
D
Test item Operation Description
RH Outputs the voltage to blink the right side turn signal lamps.
FLASHER LH Outputs the voltage to blink the left side turn signal lamps. E
Off Stops the voltage to turn the turn signal lamps OFF.
EXL
Operation
Inspection location Operation
sequence
1 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamp
2 • License plate lamp 10 seconds
• Tail lamp
3 Headlamp LO for 10 seconds →HI ON ⇔ OFF 5 times
4 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
5 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
JMMIA0887GB F
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto G
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode H
Any of the following components do not operate YES BCM signal input circuit I
• Parking lamp • Lamp or motor
Perform auto active test.
• License plate lamp • Lamp or motor ground circuit
Does the applicable system
• Tail lamp NO • Harness or connector between
• Headlamp (HI, LO)
operate? J
IPDM E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R
• BCM signal input circuit
• CAN communication signal be- K
YES tween BCM and ECM
Perform auto active test. • CAN communication signal be-
A/C compressor does not operate Does the magnet clutch oper- tween ECM and IPDM E/R
EXL
ate? • Magnet clutch
• Harness or connector between
NO
IPDM E/R and magnet clutch
• IPDM E/R M
• ECM signal input circuit
YES • CAN communication signal be-
tween ECM and IPDM E/R N
Perform auto active test.
Cooling fan does not operate • Cooling fan motor
Does the cooling fan operate?
• Harness or connector between
NO
IPDM E/R and cooling fan motor
O
• IPDM E/R
P
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
ACTIVE TEST
Test item
Hi Operates the front wiper relay and front wiper high relay.
1 OFF C
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
4 Operates the cooling fan relay (HI operation). D
NOTE:
HEAD LAMP WASHER Off
This item is indicated, but cannot be tested.
E
Off OFF
TAIL Operates the tail lamp relay.
Lo Operates the headlamp low relay.
F
EXTERNAL LAMPS
Operates simultaneously the headlamp low relay and the headlamp high relay at
Hi
1 second ON/OFF intervals.
NOTE: G
Fog
This item is indicated, but cannot be tested.
EXL
ECU Reference
BCS-28, "Reference Value"
BCS-40, "Fail-safe"
BCM
BCS-41, "DTC Inspection Priority Chart"
BCS-41, "DTC Index"
PCS-12, "Reference Value"
IPDM E/R PCS-16, "Fail-Safe"
PCS-17, "DTC Index"
WIRING DIAGRAM A
EXTERIOR LIGHTING SYSTEM
Wiring Diagram INFOID:0000000007087541
B
EXL
JCLWA5207GB
JCLWA5208GB
EXL
JCLWA5209GB
JCLWA5210GB
EXL
JCLWA5211GB
JCLWA5212GB
EXL
JCLWA5213GB
JCLWA5214GB
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000007087543
B
OVERALL SEQUENCE
C
EXL
P
JMLIA1607GB
DETAILED FLOW
1.INTERVIEW FOR MALFUNCTION
Interview the symptom to the customer.
>> GO TO 3.
3.BASIC INSPECTION
Check the operation of each part. Check that any symptom occurs other than the interviewed symptom.
>> GO TO 4.
4.SELF-DIAGNOSIS WITH CONSULT
Perform the self-diagnosis with CONSULT. Check that any DTC is detected.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform the trouble diagnosis for the detected DTC. Specify the malfunctioning part.
>> GO TO 9.
6.FAIL-SAFE ACTIVATION CHECK
Check that the symptom is applied to the fail-safe activation.
Does the fail-safe activate?
YES >> GO TO 7.
NO >> GO TO 8.
7.SYSTEM DIAGNOSIS
Perform the system diagnosis for the system that the fail-safe activates. Specify the malfunctioning part.
>> GO TO 9.
8.SYMPTOM DIAGNOSIS
Perform the symptom diagnosis. Specify the malfunctioning part.
>> GO TO 9.
9.MALFUNCTION PART REPAIR
Repair or replace the malfunctioning part.
>> GO TO 10.
10.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform the self-diagnosis with CONSULT. Check that any DTC is not detected. Erase DTC if DTC is detected
before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 11.
11.REPAIR CHECK (OPERATION CHECK)
Check the operation of each part.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 3.
DTC/CIRCUIT DIAGNOSIS A
HEADLAMP (HI) CIRCUIT
Component Function Check INFOID:0000000007087545
B
(+) J
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
K
RH Hi Battery voltage
63
Off 0V
E14 Ground EXTERNAL LAMPS
LH Hi Battery voltage EXL
61
Off 0V
Is the inspection result normal?
M
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK HEADLAMP (HI) OPEN CIRCUIT N
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector. O
IPDM E/R Headlamp
Continuity
Connector Terminal Connector Terminal
P
RH 63 E45
E14 1 Existed
LH 61 E26
Is the inspection result normal?
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 63
E14 Not existed
LH 61
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
Lo : Headlamp (LO) ON
Off : Headlamp (LO) OFF D
Is the inspection result normal?
YES >> Headlamp (LO) is normal.
E
NO >> Refer to EXL-31, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000007087548
F
1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE
CONSULT ACTIVE TEST
1. Turn ignition switch OFF. G
2. Disconnect headlamp connector.
3. Turn ignition switch ON.
4. Select “EXTERNAL LAMPS” of IPDM E/R active test item. H
5. With operating the test items, check voltage between IPDM E/R harness connector and ground.
(+)
(−) Voltage I
IPDM E/R Test item
(Approx.)
Connector Terminal
Lo Battery voltage J
RH 40
Off 0V
E12 Ground EXTERNAL LAMPS
Lo Battery voltage
LH 38 K
Off 0V
Is the inspection result normal?
YES >> GO TO 2. EXL
NO >> GO TO 3.
2.CHECK HEADLAMP (LO) OPEN CIRCUIT
1. Turn ignition switch OFF. M
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.
N
IPDM E/R Headlamp
Continuity
Connector Terminal Connector Terminal
RH 40 E45 O
E12 3 Existed
LH 38 E26
Is the inspection result normal?
P
YES >> Replace headlamp bulb.
NO >> Repair or replace harness.
3.CHECK HEADLAMP (LO) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
IPDM E/R
Continuity
Connector Terminal
Ground
RH 40
E12 Not existed
LH 38
Is the inspection result normal?
YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO >> Repair or replace harness. And then replace the fuse.
Headlamp
Continuity
Connector Terminal D
Ground
RH E45
2 Existed
LH E26
E
Is the inspection result normal?
YES >> Headlamp ground circuit is normal.
NO >> Repair or replace harness.
F
EXL
Parking lamp
Continuity
Connector Terminal
Ground
RH E43
2 Existed
LH E24
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Check continuity between rear combination lamp harness connector and ground.
M
Rear combination lamp
Continuity
Connector Terminal
Ground
RH B59 N
3 Existed
LH B80
Is the inspection result normal?
YES >> Check corresponding bulb socket and harness. Repair or replace if necessary. O
NO >> Repair or replace harness.
EXL
LH
60
M
PKID0926E
O
RH
61
P
PKID0926E
OFF 0V
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 4.
BCM
Continuity
Connector Terminal
Ground
RH 61
M67 Not existed
LH 60
Is the inspection result normal?
YES >> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to BCS-57, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between BCM harness connector and front turn signal lamp or rear combination lamp and
ground.
Front turn signal lamp
Front turn signal lamp
Continuity
Connector Terminal
Ground
RH E46
2 Existed
LH E27
(+)
Hazard switch (−) Voltage (Approx.) I
Connector Terminal
M45 2 Ground 12 V
J
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
K
2.CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector. EXL
Hazard switch
Continuity P
Connector Terminal Ground
M45 2 Not existed
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-57, "Removal and Installation".
NO >> Repair or replace harness.
Hazard switch
Continuity
Connector Terminal Ground
M45 1 Existed
Is the inspection result normal?
YES >> Replace hazard switch.
NO >> Repair or replace harness.
SYMPTOM DIAGNOSIS A
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table INFOID:0000000007087569
B
CAUTION:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected. C
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS. B
Diagnosis Procedure INFOID:0000000007087571
EXL
The parking, license plate and tail lamps are not turned ON in any condition. B
Diagnosis Procedure INFOID:0000000007087575
(+)
Voltage
IPDM E/R (−) Test item
(Approx.)
Connector Terminal
PERIODIC MAINTENANCE A
HEADLAMP AIMING ADJUSTMENT
Description INFOID:0000000007087578
B
EXL
JMLIA1020ZZ
JSLIA0030ZZ
JSLIA0031ZZ F
C. Vertical center line of headlamp H. Horizontal center line of headlamp L. Distance from headlamp center to screen
X. Aiming adjustment area Y. Aiming adjustment area
G
(lateral) (Vertical)
EXL
A: UP
B: DOWN
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
JMLIA1040ZZ
JPLIA0008ZZ
A : Cutoff line A
B : High illuminance area
H : Horizontal center line of front fog lamp
V : Vertical center line of front fog lamp B
X : Cutoff line height
EXL
REMOVAL
JMLIA1031ZZ
DISASSEMBLY
H
JMLIA1032ZZ
REMOVAL
CAUTION: K
Disconnect the battery negative terminal or the fuse.
1. Remove front bumper fascia. Refer to EXT-11, "Removal and Installation".
2. Remove the headlamp mounting bolts. EXL
3. Pull out the headlamp assembly forward the vehicle.
4. Disconnect the connectors, and then remove headlamp assembly.
M
INSTALLATION
Note the following item, and then install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to EXL-47, "Description". N
Replacement INFOID:0000000007087586
CAUTION: O
• Disconnect the battery negative terminal or the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. P
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1. Disconnect the headlamp bulb connector.
2. Remove the back cover.
DISASSEMBLY
1. Remove the back cover.
2. Remove the retaining spring lock, and then remove the bulb from the headlamp housing assembly.
3. Rotate the parking lamp bulb socket counterclockwise and unlock it.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6. Remove the bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
The lighting & turn switch is integrated in the combination switch. Refer to BCS-58, "Exploded View". B
EXL
JMLIA1042ZZ
REMOVAL
1. Remove the cluster lid C. Refer to IP-12, "Exploded View".
2. While pressing pawls, push the hazard switch to remove it.
INSTALLATION
Install in the reverse order of removal.
REMOVAL B
JMLIA1034ZZ G
DISASSEMBLY H
EXL
JMLIA1035ZZ M
1. Stop/tail lamp bulb 2. Rear turn signal lamp bulb 3. Back-up lamp bulb
4. Bulb holder 5. Seal packing N
Refer to GI-4, "Components" for symbols in the figure.
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
JMLIA1041ZZ
3. Rotate stop/tail lamp bulb counterclockwise, and then remove stop/tail lamp bulb.
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
JMLIA1041ZZ
3. Rotate rear turn signal lamp bulb counterclockwise, and then remove rear turn signal lamp bulb.
BACK-UP LAMP BULB
1. Remove rear combination lamp assembly.
2. Disengage fixing pawls, and then remove bulb holder.
JMLIA1041ZZ
3. Rotate back-up lamp bulb counterclockwise, and then remove back-up lamp bulb.
G
JMLIA1036ZZ
CAUTION:
Disconnect battery negative terminal or remove the fuse.
J
REMOVAL
1. Disengage high-mounted stop lamp fixing pawls with remover
tool (A). K
: Metal clip
CAUTION: EXL
• Apply protect tape (B) on back door to protect the painted
surface from damage.
M
JMLIA1021ZZ
N
• Never insert remover tool in the back door glass side to
prevent damage of back door glass.
O
JMLIA1022ZZ
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HIGH-MOUNTED STOP LAMP BULB
1. Remove the high-mounted stop lamp.
2. Rotate the bulb socket counterclockwise, and unlock it.
3. Remove the bulb from the bulb socket.
G
JMLIA1037ZZ
1. License plate lamp connector 2. License plate lamp bulb 3. License plate lamp housing
H
Removal and Installation INFOID:0000000007087607
CAUTION: I
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1. While pressing the license plate lamp fixing pawl to direction right side, pull it to direction lower side and J
then remove it.
2. Rotate the bulb socket counterclockwise, and then remove bulb socket.
3. Remove the license plate lamp. K
INSTALLATION
Install in the reverse order of removal.
EXL
Replacement INFOID:0000000007087608
CAUTION: M
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect N
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
O
1. Remove the license plate lamp.
2. Remove the bulb from the socket.
P